Skip to contentSkip to conversation

usbkbd input double echoed

U-Boot Nikita Kiryanov 2 participants 3 messages Nov 23, 2014 – Nov 24, 2014

lore
Share & tools
lore
#0 lore raw

Hi all,

I've enabled USB keyboard for cm_fx6 using these three defines:

#define CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL
#define CONFIG_SYS_STDIO_DEREGISTER

I am able to probe it with usb start, and set it as input using setenv stdin usbkbd.

It works, save for one problem: all key presses are echoed twice. The double echo happens both on serial and vga stdout. It is not dependant on the keyboard (tried different ones). Output from commands looks normal.
Switching to CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP did not help. Shell still understands each key press as one key press, so even though "pprriinntteennvv" is displayed, the shell still sees "printenv".

Any idea what the cause may be?

Signature · 2 lines
Regards,
Nikita Kiryanov
#1 lore raw

Hi,

Quoted 20 lines · Nikita Kiryanov

Hi all,

I've enabled USB keyboard for cm_fx6 using these three defines:

#define CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL
#define CONFIG_SYS_STDIO_DEREGISTER

I am able to probe it with usb start, and set it as input using setenv stdin usbkbd.

It works, save for one problem: all key presses are echoed twice. The double echo happens both on serial and vga stdout. It is not dependant on the keyboard (tried different ones). Output from commands looks normal.
Switching to CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP did not help. Shell still understands each key press as one key press, so even though "pprriinntteennvv" is displayed, the shell still sees "printenv".

Quoted 1 line

Any idea what the cause may be?

In my experience both polling methods are sub-optimal, if your board has an ehci controller, try using CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE

Also I use CONFIG_CONSOLE_MUX, then you can do:

setenv stdin serial,usbkbd

And get both, using this usb-kbd support works fine for me, without the double echo, both on the serial console and on the sunxi-cfb console over hdmi.

Regards,

Hans

#2 lore raw

Hi Hans,

Quoted 32 lines · Hans de Goede

Hi,

Quoted 20 lines · Nikita Kiryanov

Hi all,

I've enabled USB keyboard for cm_fx6 using these three defines:

#define CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL
#define CONFIG_SYS_STDIO_DEREGISTER

I am able to probe it with usb start, and set it as input using setenv stdin usbkbd.

It works, save for one problem: all key presses are echoed twice. The double echo happens both on serial and vga stdout. It is not dependant on the keyboard (tried different ones). Output from commands looks normal.
Switching to CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP did not help. Shell still understands each key press as one key press, so even though "pprriinntteennvv" is displayed, the shell still sees "printenv".

Quoted 1 line

Any idea what the cause may be?

In my experience both polling methods are sub-optimal, if your board has an ehci controller, try using CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE

Also I use CONFIG_CONSOLE_MUX, then you can do:

setenv stdin serial,usbkbd

Quoted 8 lines

And get both, using this usb-kbd support works fine for me, without the double echo, both on the serial console and on the sunxi-cfb console over hdmi.

Regards,

Hans

I think I must have encountered some toolchain bug. After switching to another branch to work on something else I came back to my dev branch and the compiled images no longer have this bug.

Thanks for the help though..

Signature · 2 lines
Regards,
Nikita Kiryanov