sound/soc/adi/axi-spdif.c: Support programmable master clock
PATCH 1/1 sound/soc/adi/axi-spdif.c: Support programmable master clock
If the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "hw_params" where the rate is known. Move the clock start to the hw_params routine, and keep track of whether the clock has been started, because shutdown may be called without having called hw_params first.
Starting the clock and enabling the SPDIF output AFTER programming the dividers is a more logical order anyway.
--- sound/soc/adi/axi-spdif.c | 56 ++++++++++++++++++++++++++++----------------- 1 file changed, 35 insertions(+), 21 deletions(-)
sound/soc/adi/axi-spdif.c +35 -21
@@ -4,7 +4,6 @@* * Licensed under the GPL-2. */ -#include <linux/init.h> #include <linux/kernel.h> #include <linux/module.h>
@@ -44,6 +43,8 @@ struct axi_spdif {struct snd_ratnum ratnum;struct snd_pcm_hw_constraint_ratnums rate_constraints; + +bool clk_ref_running; }; static int axi_spdif_trigger(struct snd_pcm_substream *substream, int cmd,
@@ -79,6 +80,7 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,struct axi_spdif *spdif =snd_soc_dai_get_drvdata (dai);unsigned int rate =params_rate (params);unsigned int clkdiv, stat; +int ret;switch (params_rate (params)) {case 32000 :
@@ -95,6 +97,9 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,break ; } +/* Try to set the master clock */ +clk_set_rate (spdif->clk_ref, rate *128 ); + clkdiv =DIV_ROUND_CLOSEST (clk_get_rate (spdif->clk_ref), rate *64 *2 ) -1 ; clkdiv <<=AXI_SPDIF_CTRL_CLKDIV_OFFSET ;
@@ -103,6 +108,14 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL ,AXI_SPDIF_CTRL_CLKDIV_MASK , clkdiv); + ret =clk_prepare_enable (spdif->clk_ref); +if (ret) +return ret; + spdif->clk_ref_running = true; + +regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL , +AXI_SPDIF_CTRL_TXEN ,AXI_SPDIF_CTRL_TXEN ); +return 0 ; }
@@ -121,18 +134,13 @@ static int axi_spdif_startup(struct snd_pcm_substream *substream,struct axi_spdif *spdif =snd_soc_dai_get_drvdata (dai);int ret; - ret =snd_pcm_hw_constraint_ratnums (substream->runtime,0 , -SNDRV_PCM_HW_PARAM_RATE , - &spdif->rate_constraints); -if (ret) -return ret; - - ret =clk_prepare_enable (spdif->clk_ref); -if (ret) -return ret; - -regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL , -AXI_SPDIF_CTRL_TXEN ,AXI_SPDIF_CTRL_TXEN ); +if (spdif->rate_constraints.nrats) { + ret =snd_pcm_hw_constraint_ratnums (substream->runtime,0 , +SNDRV_PCM_HW_PARAM_RATE , + &spdif->rate_constraints); +if (ret) +return ret; + }return 0 ; }
@@ -145,7 +153,10 @@ static void axi_spdif_shutdown(struct snd_pcm_substream *substream,regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL ,AXI_SPDIF_CTRL_TXEN ,0 ); -clk_disable_unprepare (spdif->clk_ref); +if (spdif->clk_ref_running) { +clk_disable_unprepare (spdif->clk_ref); + spdif->clk_ref_running = false; + } }static const struct snd_soc_dai_ops axi_spdif_dai_ops = {
@@ -216,14 +227,17 @@ static int axi_spdif_probe(struct platform_device *pdev) spdif->dma_data.addr_width =4 ; spdif->dma_data.maxburst =1 ; - spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; - spdif->ratnum.den_step =1 ; - spdif->ratnum.den_min =1 ; - spdif->ratnum.den_max =64 ; - - spdif->rate_constraints.rats = &spdif->ratnum; - spdif->rate_constraints.nrats =1 ; +/* Determine if the clock rate is fixed. If it cannot change frequency, +* it returns an error here. */ +if (clk_round_rate (spdif->clk_ref,128 *44100 ) <0 ) { + spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; + spdif->ratnum.den_step =1 ; + spdif->ratnum.den_min =1 ; + spdif->ratnum.den_max =64 ; + spdif->rate_constraints.rats = &spdif->ratnum; + spdif->rate_constraints.nrats =1 ; + } ret =devm_snd_soc_register_component (&pdev->dev, &axi_spdif_component, &axi_spdif_dai,1 );if (ret)
Signature · 1 line
1.7.9.5
Quoted 10 lines · Mike Looijmans
If the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "
hw_params" where the rate is known. Move the clock start to thehw_paramsroutine, and keep track of whether the clock has been started, because shutdown may be called without having calledhw_paramsfirst.
Usually that shouldn't be a problem. If your clock chip requires it to be disabled in order to be reprogrammed than the CLK_SET_RATE_GATE flag should be set. This will tell the core to disable the clock before changing it.
[...]
Quoted 5 lines
static const struct snd_soc_dai_ops axi_spdif_dai_ops = {sound/soc/adi/axi-spdif.c +0
-0@@ -216,14 +227,17 @@ static int axi_spdif_probe(struct platform_device *pdev) spdif->dma_data.addr_width =4 ; spdif->dma_data.maxburst =1 ;
sound/soc/adi/axi-spdif.c static int axi_spdif_probe(struct platform_device *pdev) · line 232
Quoted 10 lines
sound/soc/adi/axi-spdif.c +3
-7- spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; - spdif->ratnum.den_step =1 ; - spdif->ratnum.den_min =1 ; - spdif->ratnum.den_max =64 ; - - spdif->rate_constraints.rats = &spdif->ratnum; - spdif->rate_constraints.nrats =1 ; +/* Determine if the clock rate is fixed. If it cannot change frequency, +* it returns an error here. */ +if (clk_round_rate (spdif->clk_ref,128 *44100 ) <0 ) {
I don't think this works. For a fixed clock clk_round_rate() will return the fixed rate rather than an error. I tried the patch and even though I have a fixed clock the constraints are no longer set.
There is unfortunately no good way to enumerate which frequencies are supported by a clock other than just calling round_rate for all possible rates.
I think the best way to implement this for now is to try e.g. 32000 * 128, 44100 * 128, 48000 * 128 and then check if clk_round_rate returns the expected rate and if it does set up a rate constraint for that rate.
Quoted 12 lines · Lars-Peter Clausen
Quoted 10 lines · Mike Looijmans
If the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "
hw_params" where the rate is known. Move the clock start to thehw_paramsroutine, and keep track of whether the clock has been started, because shutdown may be called without having calledhw_paramsfirst.
Quoted 3 lines
Usually that shouldn't be a problem. If your clock chip requires it to be disabled in order to be reprogrammed than the
CLK_SET_RATE_GATEflag should be set. This will tell the core to disable the clock before changing it.
The issue here is not the clock's capabilities, but the order in which things are being done. If the driver just enables the clock without ever having set a rate, the clock will run at whatever happens to be the default. That default may have unpredictable results or even be harmful to the system. So the driver should first set a valid clock rate before enabling the clock. Suggestions on rewording my comments to better reflect that are welcome.
Quoted 22 lines
[...]
Quoted 5 lines
static const struct snd_soc_dai_ops axi_spdif_dai_ops = {sound/soc/adi/axi-spdif.c +0
-0@@ -216,14 +227,17 @@ static int axi_spdif_probe(struct platform_device *pdev) spdif->dma_data.addr_width =4 ; spdif->dma_data.maxburst =1 ;sound/soc/adi/axi-spdif.c static int axi_spdif_probe(struct platform_device *pdev) · line 232
Quoted 10 lines
sound/soc/adi/axi-spdif.c +3
-7- spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; - spdif->ratnum.den_step =1 ; - spdif->ratnum.den_min =1 ; - spdif->ratnum.den_max =64 ; - - spdif->rate_constraints.rats = &spdif->ratnum; - spdif->rate_constraints.nrats =1 ; +/* Determine if the clock rate is fixed. If it cannot change frequency, +* it returns an error here. */ +if (clk_round_rate (spdif->clk_ref,128 *44100 ) <0 ) {I don't think this works. For a fixed clock
clk_round_rate()will return the fixed rate rather than an error. I tried the patch and even though I have a fixed clock the constraints are no longer set.
Quoted 6 lines
There is unfortunately no good way to enumerate which frequencies are supported by a clock other than just calling
round_ratefor all possible rates.I think the best way to implement this for now is to try e.g. 32000 * 128, 44100 * 128, 48000 * 128 and then check if
clk_round_ratereturns the expected rate and if it does set up a rate constraint for that rate.
For what I could see, ALSA never reported or limited the sample rate correctly even before this patch, so maybe the even simpler approach is better: Just remove the constraint. I wonder how you concluded that the constraint didn't get added?
Actually, the SPDIF logic wants a clock that is an "integer multiple of 128*samplerate in the range of 1..64". Other than just looping through them all, there's also no way to request the clock framework for such a requirement.
Your suggestion is quite robust though, but the fixed clock may be set to any integer multiple of the desired frequency, so the algorithm would not work if the fixed clock is running at 48000*256 (12.8MHz like in the reference design). So I guess the best I could do here is just check that:
clk_round_rate(spdif->clk_ref, 128 * 44100) != clk_round_rate(spdif->clk_ref, 128 * 48000)
Only a configurable clock that is compatible with the patch would do that.
Met vriendelijke groet / kind regards,
Mike Looijmans
System Expert
TOPIC Embedded Systems Eindhovenseweg 32-C, NL-5683 KH Best Postbus 440, NL-5680 AK Best
Telefoon: (+31) (0) 499 33 69 79
Telefax: (+31) (0) 499 33 69 70
E-mail: [email protected]
Website: www.topic.nl
Please consider the environment before printing this e-mail
Topic zoekt gedreven (embedded) software specialisten!
http://topic.nl/vacatures/topic-zoekt-software-engineers/
_______________________________________________
Alsa-devel mailing list [email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 58 lines · Mike Looijmans
Quoted 12 lines · Lars-Peter Clausen
Quoted 10 lines · Mike Looijmans
If the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "
hw_params" where the rate is known. Move the clock start to thehw_paramsroutine, and keep track of whether the clock has been started, because shutdown may be called without having calledhw_paramsfirst.Quoted 4 lines
Usually that shouldn't be a problem. If your clock chip requires it to be disabled in order to be reprogrammed than the
CLK_SET_RATE_GATEflag should be
set. This will tell the core to disable the clock before changing it.The issue here is not the clock's capabilities, but the order in which things are being done. If the driver just enables the clock without ever having set a rate, the clock will run at whatever happens to be the default. That default may have unpredictable results or even be harmful to the system. So the driver should first set a valid clock rate before enabling the clock. Suggestions on rewording my comments to better reflect that are welcome.
Quoted 23 lines
[...]
Quoted 6 lines
static const struct snd_soc_dai_ops axi_spdif_dai_ops = {sound/soc/adi/axi-spdif.c +0
-0@@ -216,14 +227,17 @@ static int axi_spdif_probe(struct platform_device *pdev) spdif->dma_data.addr_width =4 ; spdif->dma_data.maxburst =1 ;sound/soc/adi/axi-spdif.c static int axi_spdif_probe(struct platform_device · line 233
Quoted 10 lines
sound/soc/adi/axi-spdif.c +3
-7- spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; - spdif->ratnum.den_step =1 ; - spdif->ratnum.den_min =1 ; - spdif->ratnum.den_max =64 ; - - spdif->rate_constraints.rats = &spdif->ratnum; - spdif->rate_constraints.nrats =1 ; +/* Determine if the clock rate is fixed. If it cannot change frequency, +* it returns an error here. */ +if (clk_round_rate (spdif->clk_ref,128 *44100 ) <0 ) {I don't think this works. For a fixed clock
clk_round_rate()will return the fixed rate rather than an error. I tried the patch and even though I have a fixed clock the constraints are no longer set.Quoted 8 lines
There is unfortunately no good way to enumerate which frequencies are supported by a clock other than just calling
round_ratefor all possible rates.I think the best way to implement this for now is to try e.g. 32000 * 128, 44100 * 128, 48000 * 128 and then check if
clk_round_ratereturns the expected
rate and if it does set up a rate constraint for that rate.
Quoted 4 lines
For what I could see, ALSA never reported or limited the sample rate correctly even before this patch, so maybe the even simpler approach is
better: Just remove the constraint. I wonder how you concluded that the constraint didn't get added?
Newer versions of aplay e.g. support printing the initial constraints:
http://git.alsa-project.org/?p=alsa-utils.git;a=blob;f=aplay/aplay.c;h=e58e1bcbdd7e5c784b85df90f15ef41326d3f6dd;hb=HEAD#l240
And on older versions you can use -v to print the final constraints. E.g. without your patch I see "Actual rate: 96000/2 (48000)" and with your patch just "Actual rate: 48000".
The application you are using might just simply choose to ignore the constraints. But there are definitely applications which honer them which will break if the constraints are removed.
Quoted 5 lines
Actually, the SPDIF logic wants a clock that is an "integer multiple of 128*samplerate in the range of 1..64". Other than just looping through them all, there's also no way to request the clock framework for such a requirement.
Quoted 8 lines
Your suggestion is quite robust though, but the fixed clock may be set to any integer multiple of the desired frequency, so the algorithm would not work if the fixed clock is running at 48000*256 (12.8MHz like in the reference design). So I guess the best I could do here is just check that:
clk_round_rate(spdif->clk_ref, 128 * 44100)!=clk_round_rate(spdif->clk_ref, 128 * 48000)
Sounds like a OK compromise.
- Lars
PATCH v2 1/1 sound/soc/adi/axi-spdif.c: Support programmable master clock
In reply to Mike LooijmansIf the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "hw_params" where the rate is known. Enabling a programmable clock without first setting a valid frequency may harm the system. Move the clock start to the hw_params routine, and keep track of whether the clock has been started, because shutdown may be called without having called hw_params first. Starting the clock and enabling the SPDIF output AFTER programming the dividers is a more logical order anyway.
To detect if the source clock is fixed, the driver calls clk_round_rate for two frequencies. If the results are equal, or if the call returns an error, the driver assumes the clock is fixed.
---
v2: Fix fixed clock detection as discussed.
sound/soc/adi/axi-spdif.c | 60 ++++++++++++++++++++++++++++----------------- 1 file changed, 38 insertions(+), 22 deletions(-)
sound/soc/adi/axi-spdif.c +38 -22
@@ -4,7 +4,6 @@* * Licensed under the GPL-2. */ -#include <linux/init.h> #include <linux/kernel.h> #include <linux/module.h>
@@ -44,6 +43,8 @@ struct axi_spdif {struct snd_ratnum ratnum;struct snd_pcm_hw_constraint_ratnums rate_constraints; + +bool clk_ref_running; }; static int axi_spdif_trigger(struct snd_pcm_substream *substream, int cmd,
@@ -79,6 +80,7 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,struct axi_spdif *spdif =snd_soc_dai_get_drvdata (dai);unsigned int rate =params_rate (params);unsigned int clkdiv, stat; +int ret;switch (params_rate (params)) {case 32000 :
@@ -95,6 +97,9 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,break ; } +/* Try to set the master clock */ +clk_set_rate (spdif->clk_ref, rate *128 ); + clkdiv =DIV_ROUND_CLOSEST (clk_get_rate (spdif->clk_ref), rate *64 *2 ) -1 ; clkdiv <<=AXI_SPDIF_CTRL_CLKDIV_OFFSET ;
@@ -103,6 +108,14 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL ,AXI_SPDIF_CTRL_CLKDIV_MASK , clkdiv); + ret =clk_prepare_enable (spdif->clk_ref); +if (ret) +return ret; + spdif->clk_ref_running = true; + +regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL , +AXI_SPDIF_CTRL_TXEN ,AXI_SPDIF_CTRL_TXEN ); +return 0 ; }
@@ -121,18 +134,13 @@ static int axi_spdif_startup(struct snd_pcm_substream *substream,struct axi_spdif *spdif =snd_soc_dai_get_drvdata (dai);int ret; - ret =snd_pcm_hw_constraint_ratnums (substream->runtime,0 , -SNDRV_PCM_HW_PARAM_RATE , - &spdif->rate_constraints); -if (ret) -return ret; - - ret =clk_prepare_enable (spdif->clk_ref); -if (ret) -return ret; - -regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL , -AXI_SPDIF_CTRL_TXEN ,AXI_SPDIF_CTRL_TXEN ); +if (spdif->rate_constraints.nrats) { + ret =snd_pcm_hw_constraint_ratnums (substream->runtime,0 , +SNDRV_PCM_HW_PARAM_RATE , + &spdif->rate_constraints); +if (ret) +return ret; + }return 0 ; }
@@ -145,7 +153,10 @@ static void axi_spdif_shutdown(struct snd_pcm_substream *substream,regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL ,AXI_SPDIF_CTRL_TXEN ,0 ); -clk_disable_unprepare (spdif->clk_ref); +if (spdif->clk_ref_running) { +clk_disable_unprepare (spdif->clk_ref); + spdif->clk_ref_running = false; + } }static const struct snd_soc_dai_ops axi_spdif_dai_ops = {
@@ -183,6 +194,7 @@ static int axi_spdif_probe(struct platform_device *pdev)struct resource *res;void __iomem *base;int ret; +long rate; spdif =devm_kzalloc (&pdev->dev,sizeof (*spdif),GFP_KERNEL );if (!spdif)
@@ -216,14 +228,18 @@ static int axi_spdif_probe(struct platform_device *pdev) spdif->dma_data.addr_width =4 ; spdif->dma_data.maxburst =1 ; - spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; - spdif->ratnum.den_step =1 ; - spdif->ratnum.den_min =1 ; - spdif->ratnum.den_max =64 ; - - spdif->rate_constraints.rats = &spdif->ratnum; - spdif->rate_constraints.nrats =1 ; - +/* Determine if the clock rate is fixed. If it cannot change frequency, +* it returns an error or it will simply return its fixed value. */ + rate =clk_round_rate (spdif->clk_ref,128 *44100 ); +if (rate <0 || rate !=clk_round_rate (spdif->clk_ref,128 *48000 )) { + spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; + spdif->ratnum.den_step =1 ; + spdif->ratnum.den_min =1 ; + spdif->ratnum.den_max =64 ; + + spdif->rate_constraints.rats = &spdif->ratnum; + spdif->rate_constraints.nrats =1 ; + } ret =devm_snd_soc_register_component (&pdev->dev, &axi_spdif_component, &axi_spdif_dai,1 );if (ret)
Signature · 1 line
1.7.9.5
Quoted 14 lines · Mike Looijmans
If the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "
hw_params" where the rate is known. Enabling a programmable clock without first setting a valid frequency may harm the system. Move the clock start to thehw_paramsroutine, and keep track of whether the clock has been started, because shutdown may be called without having calledhw_paramsfirst. Starting the clock and enabling the SPDIF output AFTER programming the dividers is a more logical order anyway.
Quoted 5 lines
To detect if the source clock is fixed, the driver calls
clk_round_ratefor two frequencies. If the results are equal, or if the call returns an error, the driver assumes the clock is fixed.Signed-off-by Mike Looijmans <[email protected]>
Hi,
Sorry for the delay.
[...]
sound/soc/adi/axi-spdif.c static int axi_spdif_hw_params(struct snd_pcm_substream *substream, · line 111
Quoted 12 lines
sound/soc/adi/axi-spdif.c +4
-0+/* Try to set the master clock */ +clk_set_rate (spdif->clk_ref, rate *128 ); + clkdiv =DIV_ROUND_CLOSEST (clk_get_rate (spdif->clk_ref), rate *64 *2 ) -1 ; clkdiv <<=AXI_SPDIF_CTRL_CLKDIV_OFFSET ;@@ -103,6 +108,14 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL ,AXI_SPDIF_CTRL_CLKDIV_MASK , clkdiv); + ret =clk_prepare_enable (spdif->clk_ref);
I'm still not convinced this is the right place. I do see your point. But it just feels wrong to enable the clock in hw_params. It's a bit of a dilemma. the startup callback is to early, hw_params is the wrong place and we can't put it in the trigger callback as the trigger callback can not sleep.
But in any way hwparmas can be called multiple times, so you need to handle the case where the clock is already enabled.
sound/soc/adi/axi-spdif.c static int axi_spdif_hw_params(struct snd_pcm_substream *substream, · line 117
Quoted 6 lines
sound/soc/adi/axi-spdif.c +6
-0+if (ret) +return ret; + spdif->clk_ref_running = true; + +regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL , +AXI_SPDIF_CTRL_TXEN ,AXI_SPDIF_CTRL_TXEN );
This should probably be moved to the trigger callback though.
Quoted 3 lines
sound/soc/adi/axi-spdif.c +1
-0+return 0 ; }
Quoted 38 lines · Lars-Peter Clausen
Quoted 14 lines · Mike Looijmans
If the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "
hw_params" where the rate is known. Enabling a programmable clock without first setting a valid frequency may harm the system. Move the clock start to thehw_paramsroutine, and keep track of whether the clock has been started, because shutdown may be called without having calledhw_paramsfirst. Starting the clock and enabling the SPDIF output AFTER programming the dividers is a more logical order anyway.Quoted 5 lines
To detect if the source clock is fixed, the driver calls
clk_round_ratefor two frequencies. If the results are equal, or if the call returns an error, the driver assumes the clock is fixed.Signed-off-by Mike Looijmans <[email protected]>Hi,
Sorry for the delay.
[...]
Quoted 12 lines
sound/soc/adi/axi-spdif.c +3
-0+/* Try to set the master clock */ +clk_set_rate (spdif->clk_ref, rate *128 ); + clkdiv =DIV_ROUND_CLOSEST (clk_get_rate (spdif->clk_ref), rate *64 *2 ) -1 ; clkdiv <<=AXI_SPDIF_CTRL_CLKDIV_OFFSET ;@@ -103,6 +108,14 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL ,AXI_SPDIF_CTRL_CLKDIV_MASK , clkdiv);
Quoted 6 lines
sound/soc/adi/axi-spdif.c static int axi_spdif_hw_params(struct snd_pcm_substream *substream, · line 111
Quoted 1 line
sound/soc/adi/axi-spdif.c +1
-0+ ret =clk_prepare_enable (spdif->clk_ref);I'm still not convinced this is the right place. I do see your point. But it just feels wrong to enable the clock in
hw_params. It's a bit of a dilemma. the startup callback is to early,hw_paramsis the wrong place and we can't put it in the trigger callback as the trigger callback can not sleep.
The clock interface suggests that we should do the clk_prepare in hw_params and the clk_enable in trigger then, since clk_prepare may sleep but clk_enable cannot. Which would complicate the clock state housekeeping because I'd have to keep track of prepare and enable states separately.
(Imagine the housekeeping on a board that could have two codecs running on one DAI using the clock generated by a third codec... I never even bothered to submit that...)
Quoted 2 lines
But in any way hwparmas can be called multiple times, so you need to handle the case where the clock is already enabled.
A simple "if (spdif->clk_ref_running)" check would fix that. I wasn't aware of that though, I thought there'd be a shutdown before another hw_params.
Quoted 8 lines
sound/soc/adi/axi-spdif.c static int axi_spdif_hw_params(struct snd_pcm_substream *substream, · line 117
Quoted 6 lines
sound/soc/adi/axi-spdif.c +6
-0+if (ret) +return ret; + spdif->clk_ref_running = true; + +regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL , +AXI_SPDIF_CTRL_TXEN ,AXI_SPDIF_CTRL_TXEN );This should probably be moved to the trigger callback though.
I'll create a v3.
Met vriendelijke groet / kind regards,
Mike Looijmans
System Expert
TOPIC Embedded Systems Eindhovenseweg 32-C, NL-5683 KH Best Postbus 440, NL-5680 AK Best
Telefoon: (+31) (0) 499 33 69 79
Telefax: (+31) (0) 499 33 69 70
E-mail: [email protected]
Website: www.topic.nl
Please consider the environment before printing this e-mail
Topic zoekt gedreven (embedded) software specialisten!
http://topic.nl/vacatures/topic-zoekt-software-engineers/
PATCH v3 1/1 sound/soc/adi/axi-spdif.c: Support programmable master clock
If the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "hw_params" where the rate is known. Enabling a programmable clock without first setting a valid frequency may harm the system. Move the clock start to the hw_params routine, and keep track of whether the clock has been started, because shutdown may be called without having called hw_params first, and hw_params may be called multiple times.
Starting the clock and enabling the SPDIF output AFTER programming the dividers is a more logical order anyway.
To detect if the source clock is fixed, the driver calls clk_round_rate for two frequencies. If the results are equal, or if the call returns an error, the driver assumes the clock is fixed.
---
v3: Only enable clock once in hw_params which may be called multiple times.
sound/soc/adi/axi-spdif.c | 62 +++++++++++++++++++++++++++++---------------- 1 file changed, 40 insertions(+), 22 deletions(-)
sound/soc/adi/axi-spdif.c +40 -22
@@ -4,7 +4,6 @@* * Licensed under the GPL-2. */ -#include <linux/init.h> #include <linux/kernel.h> #include <linux/module.h>
@@ -44,6 +43,8 @@ struct axi_spdif {struct snd_ratnum ratnum;struct snd_pcm_hw_constraint_ratnums rate_constraints; + +bool clk_ref_running; }; static int axi_spdif_trigger(struct snd_pcm_substream *substream, int cmd,
@@ -79,6 +80,7 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,struct axi_spdif *spdif =snd_soc_dai_get_drvdata (dai);unsigned int rate =params_rate (params);unsigned int clkdiv, stat; +int ret;switch (params_rate (params)) {case 32000 :
@@ -95,6 +97,9 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,break ; } +/* Try to set the master clock */ +clk_set_rate (spdif->clk_ref, rate *128 ); + clkdiv =DIV_ROUND_CLOSEST (clk_get_rate (spdif->clk_ref), rate *64 *2 ) -1 ; clkdiv <<=AXI_SPDIF_CTRL_CLKDIV_OFFSET ;
@@ -103,6 +108,16 @@ static int axi_spdif_hw_params(struct snd_pcm_substream *substream,regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL ,AXI_SPDIF_CTRL_CLKDIV_MASK , clkdiv); +if (!spdif->clk_ref_running) { + ret =clk_prepare_enable (spdif->clk_ref); +if (ret) +return ret; + spdif->clk_ref_running = true; + } + +regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL , +AXI_SPDIF_CTRL_TXEN ,AXI_SPDIF_CTRL_TXEN ); +return 0 ; }
@@ -121,18 +136,13 @@ static int axi_spdif_startup(struct snd_pcm_substream *substream,struct axi_spdif *spdif =snd_soc_dai_get_drvdata (dai);int ret; - ret =snd_pcm_hw_constraint_ratnums (substream->runtime,0 , -SNDRV_PCM_HW_PARAM_RATE , - &spdif->rate_constraints); -if (ret) -return ret; - - ret =clk_prepare_enable (spdif->clk_ref); -if (ret) -return ret; - -regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL , -AXI_SPDIF_CTRL_TXEN ,AXI_SPDIF_CTRL_TXEN ); +if (spdif->rate_constraints.nrats) { + ret =snd_pcm_hw_constraint_ratnums (substream->runtime,0 , +SNDRV_PCM_HW_PARAM_RATE , + &spdif->rate_constraints); +if (ret) +return ret; + }return 0 ; }
@@ -145,7 +155,10 @@ static void axi_spdif_shutdown(struct snd_pcm_substream *substream,regmap_update_bits (spdif->regmap,AXI_SPDIF_REG_CTRL ,AXI_SPDIF_CTRL_TXEN ,0 ); -clk_disable_unprepare (spdif->clk_ref); +if (spdif->clk_ref_running) { +clk_disable_unprepare (spdif->clk_ref); + spdif->clk_ref_running = false; + } }static const struct snd_soc_dai_ops axi_spdif_dai_ops = {
@@ -183,6 +196,7 @@ static int axi_spdif_probe(struct platform_device *pdev)struct resource *res;void __iomem *base;int ret; +long rate; spdif =devm_kzalloc (&pdev->dev,sizeof (*spdif),GFP_KERNEL );if (!spdif)
@@ -216,14 +230,18 @@ static int axi_spdif_probe(struct platform_device *pdev) spdif->dma_data.addr_width =4 ; spdif->dma_data.maxburst =1 ; - spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; - spdif->ratnum.den_step =1 ; - spdif->ratnum.den_min =1 ; - spdif->ratnum.den_max =64 ; - - spdif->rate_constraints.rats = &spdif->ratnum; - spdif->rate_constraints.nrats =1 ; - +/* Determine if the clock rate is fixed. If it cannot change frequency, +* it returns an error or it will simply return its fixed value. */ + rate =clk_round_rate (spdif->clk_ref,128 *44100 ); +if (rate <0 || rate !=clk_round_rate (spdif->clk_ref,128 *48000 )) { + spdif->ratnum.num =clk_get_rate (spdif->clk_ref) /128 ; + spdif->ratnum.den_step =1 ; + spdif->ratnum.den_min =1 ; + spdif->ratnum.den_max =64 ; + + spdif->rate_constraints.rats = &spdif->ratnum; + spdif->rate_constraints.nrats =1 ; + } ret =devm_snd_soc_register_component (&pdev->dev, &axi_spdif_component, &axi_spdif_dai,1 );if (ret)
Signature · 1 line
1.7.9.5
Quoted 15 lines · Mike Looijmans
If the master clock supports programmable rates, program it to generate the desired frequency. Only apply constraints when the clock is fixed. This allows proper clock generation for both 44100 and 48000 Hz based sampling rates if the platform supports it.
The clock frequency must be set before enabling it. Enabling the clock was done in "startup", but that occurs before "
hw_params" where the rate is known. Enabling a programmable clock without first setting a valid frequency may harm the system. Move the clock start to thehw_paramsroutine, and keep track of whether the clock has been started, because shutdown may be called without having calledhw_paramsfirst, andhw_paramsmay be called multiple times.
Starting the clock and enabling the SPDIF output AFTER programming the dividers is a more logical order anyway.
Quoted 5 lines
To detect if the source clock is fixed, the driver calls
clk_round_ratefor two frequencies. If the results are equal, or if the call returns an error, the driver assumes the clock is fixed.Signed-off-by Mike Looijmans <[email protected]>
Thanks.