drivers/regulator/core.c: Don't print error on EPROBE_DEFER
PATCH 1/2 drivers/regulator/core.c: Don't print error on EPROBE_DEFER
If a regulator depends on another regulator that happens to be called later, the kernel always prints a message like this:
reg-fixed-voltage regulator_sd1: Failed to find supply vin
Since the deferral is not something fatal, nor even something the user may need to be aware about, reduce the message to debug level.
This fixes a storm of error messages at boot when a board has a power regulator on an I2C bus which powers GPIO controlled regulators for example.
--- drivers/regulator/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/regulator/core.c +1 -1
@@ -3715,7 +3715,7 @@ regulator_register(const struct regulator_desc *regulator_desc, ret =0 ; goto add_dev; }else if (!r) { -dev_err (dev,"Failed to find supply %s\n" , supply); +dev_dbg (dev,"Failed to find supply %s\n" , supply); ret = -EPROBE_DEFER ; goto scrub; }
Signature · 1 line
1.7.9.5
PATCH 2/2 regulator/fixed.c: Don't report EPROBE_DEFER errors
If the regulator cannot be registered because its supplier is not available yet, don't write an error. There is no need to alert the user of probe deferrals.
This fixes a storm of error messages at boot when a GPIO controlled regulator is supplied by an I2C controlled supply.
--- drivers/regulator/fixed.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/regulator/fixed.c +3 -1
@@ -189,7 +189,9 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev) &cfg);if (IS_ERR (drvdata->dev)) { ret =PTR_ERR (drvdata->dev); -dev_err (&pdev->dev,"Failed to register regulator: %d\n" , ret); +if (ret != -EPROBE_DEFER ) +dev_err (&pdev->dev, +"Failed to register regulator: %d\n" , ret);return ret; }
Signature · 1 line
1.7.9.5
Mark Brown
maintainerQuoted 5 lines · Mike Looijmans
If a regulator depends on another regulator that happens to be called later, the kernel always prints a message like this:
reg-fixed-voltageregulator_sd1: Failed to find supply vin
Since the deferral is not something fatal, nor even something the user may need to be aware about, reduce the message to debug level.
No, we need to tell users if we're deferring since there's no guarantee that the device blocking registration is ever going to be loaded - we need to let the user know why the device isn't appearing so that they can diagnose problems. Yes, it's noisy and ideally we'd have something more efficient than deferred probe but there we are.
Quoted 5 lines · Mark Brown
Quoted 5 lines
If a regulator depends on another regulator that happens to be called later, the kernel always prints a message like this:
reg-fixed-voltageregulator_sd1: Failed to find supply vin
Since the deferral is not something fatal, nor even something the user may need to be aware about, reduce the message to debug level.
Can we instead at least reduce it to WARN or INFO level then?
I have to explain over and over again that there's no problem when that message comes along ten times in a row. And it causes people to overlook the messages that really are errors.
Signature · 1 line
Mike Looijmans
Mark Brown
maintainerQuoted 9 lines · Mike Looijmans
Quoted 5 lines · Mark Brown
Quoted 5 lines
If a regulator depends on another regulator that happens to be called later, the kernel always prints a message like this:
reg-fixed-voltageregulator_sd1: Failed to find supply vin
Since the deferral is not something fatal, nor even something the user may need to be aware about, reduce the message to debug level.Can we instead at least reduce it to WARN or INFO level then?
You appear to have deleted my reply here... one problem with your suggestion is that it means we have to special case all error handling on probe for deferral which isn't wonderful.
Quoted 3 lines
I have to explain over and over again that there's no problem when that message comes along ten times in a row. And it causes people to overlook the messages that really are errors.
Can we do something with the log message that triggers on probe deferral? There tends to be a learning curve with probe deferral but the fact that it's generally extremely noisy tends to be useful - I usually point people at that (not just in the context at regulators) and tell them not to worry unless debugging.
Quoted 2 lines · Mark Brown
Can we do something with the log message that triggers on probe deferral?
Maybe add and use rdev_err_ratelimited?
Mark Brown
maintainerQuoted 6 lines · Joe Perches
Quoted 2 lines · Mark Brown
Can we do something with the log message that triggers on probe deferral?
Maybe add and use
rdev_err_ratelimited?
That's not going to help, the volume isn't sufficiently high and comes from many different devices.
Quoted 9 lines · Mark Brown
Quoted 7 lines · Mike Looijmans
Quoted 5 lines · Mark Brown
Quoted 5 lines
If a regulator depends on another regulator that happens to be called later, the kernel always prints a message like this:
reg-fixed-voltageregulator_sd1: Failed to find supply vin
Since the deferral is not something fatal, nor even something the user may need to be aware about, reduce the message to debug level.
Quoted 5 lines
Quoted 1 line
Can we instead at least reduce it to WARN or INFO level then?
You appear to have deleted my reply here... one problem with your suggestion is that it means we have to special case all error handling on probe for deferral which isn't wonderful.
(Sorry for deleting your reply. It wasn't intentional though.)
special casing deferral may not be "wonderful", but it is what currently happens in many places, and it's just "the best we can do for now". A similar patch for MMC got approval:
https://lkml.org/lkml/2014/10/27/477
Quoted 9 lines
Quoted 3 lines
I have to explain over and over again that there's no problem when that message comes along ten times in a row. And it causes people to overlook the messages that really are errors.
Can we do something with the log message that triggers on probe deferral? There tends to be a learning curve with probe deferral but the fact that it's generally extremely noisy tends to be useful - I usually point people at that (not just in the context at regulators) and tell them not to worry unless debugging.
Using "dev_err" is not really "tell them not to worry unless debugging", I think that is what "dev_dbg" was meant to do.
The only real solution I could come up with here is to replace "return -EPROBE_DEFER" with something that stores the current stack, registers the resource it requires and jumps back to where the driver probe originated. Once the resource is available, the stored stack is resumed and then the probe code path can continue as if nothing bad happened. This would also deliver excellent diagnostic data in case the resource remains absent. I've built something like this in Python which has a "yield" statement one can use for this purpose. It's a bit tougher to do in C I guess. So until then, we're stuck with sprinkling "if (ret == -EPROBE_DEFER)" code snippets all over the place.
Met vriendelijke groet / kind regards,
Mike Looijmans
System Expert
TOPIC Embedded Systems Eindhovenseweg 32-C, NL-5683 KH Best Postbus 440, NL-5680 AK Best
Telefoon: (+31) (0) 499 33 69 79
Telefax: (+31) (0) 499 33 69 70
E-mail: [email protected]
Website: www.topic.nl
Please consider the environment before printing this e-mail
Topic zoekt gedreven (embedded) software specialisten!
http://topic.nl/vacatures/topic-zoekt-software-engineers/
Mark Brown
maintainerQuoted 5 lines · Mike Looijmans
Quoted 3 lines · Mark Brown
Quoted 1 line · Mike Looijmans
Can we instead at least reduce it to WARN or INFO level then?
Quoted 8 lines
Quoted 3 lines
You appear to have deleted my reply here... one problem with your suggestion is that it means we have to special case all error handling on probe for deferral which isn't wonderful.
special casing deferral may not be "wonderful", but it is what currently happens in many places, and it's just "the best we can do for now". A similar patch for MMC got approval:
https://lkml.org/lkml/2014/10/27/477
That's just one call site, were all the other places that might see a probe deferral updated too?
That also looks like a case of the core passing through other errors rather than a case of primary error reporting - I guess there's a reasonable case for the core not logging at all here since the drivers ought to be doing it.
Quoted 4 lines
Quoted 3 lines
Quoted 3 lines
I have to explain over and over again that there's no problem when that message comes along ten times in a row. And it causes people to overlook the messages that really are errors.
Quoted 8 lines
Quoted 5 lines
Can we do something with the log message that triggers on probe deferral? There tends to be a learning curve with probe deferral but the fact that it's generally extremely noisy tends to be useful - I usually point people at that (not just in the context at regulators) and tell them not to worry unless debugging.
Using "
dev_err" is not really "tell them not to worry unless debugging", I think that is what "dev_dbg" was meant to do.
Well, then the core probe deferral stuff ought to be less chatty then...
Quoted 10 lines
The only real solution I could come up with here is to replace "return -EPROBE_DEFER" with something that stores the current stack, registers the resource it requires and jumps back to where the driver probe originated. Once the resource is available, the stored stack is resumed and then the probe code path can continue as if nothing bad happened. This would also deliver excellent diagnostic data in case the resource remains absent. I've built something like this in Python which has a "yield" statement one can use for this purpose. It's a bit tougher to do in C I guess. So until then, we're stuck with sprinkling "if (ret == -EPROBE_DEFER)" code snippets all over the place.
There was a proposal the other day for a restrack framework (name might change in future) which drivers would call in their probe and get a callback when everything appears.