drivers/video/am335x-fb: Add possibility to wait for stable power/picture
PATCH 1/21 drivers/video/am335x-fb: Add possibility to wait for stable power/picture
Often on boards exists a circuit which switches power on/off to LCD display. Due to the need of limiting the in-rush current the output voltage from this circuit rises "slowly", so it is necessary to wait a bit (VCC ramp up time) before starting output on LCD-pins.
This time is specified in <n> ms within the panel-settings, called "pup_delay"
Further some LCDs need a couple of frames to stabilize the image on it. We have now the possibility to wait some time after starting output on LCD. This time is also specified in <n> ms within panel-settings, called "pon_delay"
--- drivers/video/am335x-fb.c | 13 ++++++++----- drivers/video/am335x-fb.h | 9 +++++++-- 2 files changed, 15 insertions(+), 7 deletions(-)
drivers/video/am335x-fb.c +8 -5
@@ -127,6 +127,12 @@ int am335xfb_init(struct am335x_lcdpanel *panel)memset ((void *)gd->fb_base,0 ,0x20 ); *(unsigned int *)gd->fb_base =0x4000 ; +/* turn ON display through powercontrol function if accessible */ +if (0 != panel->panel_power_ctrl) + panel->panel_power_ctrl (1 ); + +debug ("am335x-fb: wait for stable power ...\n" ); +mdelay (panel->pup_delay); lcdhw->clkc_enable =LCD_CORECLKEN |LCD_LIDDCLKEN |LCD_DMACLKEN ; lcdhw->raster_ctrl =0 ; lcdhw->ctrl =LCD_CLK_DIVISOR (panel->pxl_clk_div) |LCD_RASTER_MODE ;
@@ -159,11 +165,8 @@ int am335xfb_init(struct am335x_lcdpanel *panel) gd->fb_base +=0x20 ;/* point fb behind palette */ -/* turn ON display through powercontrol function if accessible */ -if (0 != panel->panel_power_ctrl) { -mdelay (panel->pon_delay); - panel->panel_power_ctrl (1 ); - } +debug ("am335x-fb: waiting picture to be stable.\n." ); +mdelay (panel->pon_delay);return 0 ; }
drivers/video/am335x-fb.h +7 -2
@@ -55,9 +55,14 @@ struct am335x_lcdpanel {unsigned int vsw;/* Vertical Sync Pulse Width */ unsigned int pxl_clk_div;/* Pixel clock divider*/ unsigned int pol;/* polarity of sync, clock signals */ +unsigned int pup_delay;/* +* time in ms after power on to +* initialization of lcd-controller +* (VCC ramp up time) +*/ unsigned int pon_delay;/* -* time in ms for turning on lcd after -* initializing lcd-controller +* time in ms after initialization of +* lcd-controller (pic stabilization) */ void (*panel_power_ctrl)(int );/* fp for power on/off display */ };
Signature · 1 line
1.7.9.5
PATCH 2/21 common/lcd: Add command for setting cursor within lcd-framework
We need this function if we want to make some outputs i.e position the writing cursor out of u-boot scripts.
--- common/lcd.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
common/lcd.c +21 -0
@@ -279,12 +279,33 @@ static int do_lcd_clear(cmd_tbl_t *cmdtp, int flag, int argc,return 0 ; } +static int do_lcd_setcursor (cmd_tbl_t *cmdtp,int flag,int argc, +char *const argv[]) +{ +unsigned int col, row; + +if (argc !=3 ) +return CMD_RET_USAGE ; + + col =simple_strtoul (argv[1 ],NULL ,10 ); + row =simple_strtoul (argv[2 ],NULL ,10 ); +lcd_position_cursor (col, row); + +return 0 ; +} +U_BOOT_CMD ( cls,1 ,1 , do_lcd_clear,"clear screen" ,"" ); +U_BOOT_CMD ( + setcurs,3 ,1 , do_lcd_setcursor, +"sets cursor for 'puts'" , +" <col> <row> in character" +); +/*----------------------------------------------------------------------*/ static int lcd_init (void *lcdbase)
Signature · 1 line
1.7.9.5
PATCH 2/21 common/lcd: Add command for setting cursor within lcd-framework
Hi Hannes,
Quoted 2 lines · Hannes Petermaier
We need this function if we want to make some outputs i.e position the writing cursor out of u-boot scripts.
This commit message is inaccurate. Positioning the writing cursor is not in itself output. Also, what is the use case for such a command?
Quoted 31 lines
Signed-off-by Hannes Petermaier <[email protected]>--- common/lcd.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)common/lcd.c +15
-0@@ -279,12 +279,33 @@ static int do_lcd_clear(cmd_tbl_t *cmdtp, int flag, int argc,return 0 ; } +static int do_lcd_setcursor (cmd_tbl_t *cmdtp,int flag,int argc, +char *const argv[]) +{ +unsigned int col, row; + +if (argc !=3 ) +return CMD_RET_USAGE ; + + col =simple_strtoul (argv[1 ],NULL ,10 ); + row =simple_strtoul (argv[2 ],NULL ,10 ); +lcd_position_cursor (col, row); + +return 0 ; +} + U_BOOT_CMD( cls, 1, 1, do_lcd_clear,
common/lcd.c static int do_lcd_clear(cmd_tbl_t *cmdtp, int flag, int argc, · line 308
Quoted 10 lines
common/lcd.c +6
-0"clear screen" ,"" ); +U_BOOT_CMD ( + setcurs,3 ,1 , do_lcd_setcursor, +"sets cursor for 'puts'" , +" <col> <row> in character" +); +
I think it would be better if the U_BOOT_CMD macros were adjacent to the functions they use. Also, I think this command is better suited for the lcd_console.c file.
Quoted 4 lines
common/lcd.c +0
-0/*----------------------------------------------------------------------*/ static int lcd_init (void *lcdbase)
Signature · 2 lines
Regards, Nikita Kiryanov
PATCH 2/21 common/lcd: Add command for setting cursor within lcd-framework
"U-Boot" <[email protected]> schrieb am 01.02.2015 15:48:51:
Quoted 4 lines
From: Nikita Kiryanov <[email protected]>
To: Hannes Petermaier <[email protected]>, u-boot at lists.denx.de
Date: 01.02.2015 15:49
Subject: Re: [U-Boot] [PATCH 02/21] common/lcd: Add command for setting
cursor
Quoted 4 lines
within lcd-framework
Sent by: "U-Boot" <[email protected]>Hi Hannes,
Hi Nikita,
Quoted 3 lines · Hannes Petermaier
Quoted 1 line
We need this function if we want to make some outputs i.e position the
writing
Quoted 3 lines
Quoted 1 line
cursor out of u-boot scripts.
This commit message is inaccurate. Positioning the writing cursor is not
in
Quoted 3 lines
itself output.
Also, what is the use case for such a command?
I want to set the "cursor" on the screen to a specific position and write there something
with "puts".
For example:
setcurs 1 9; sets the cursor to first column and 9th row
puts "Hello World!" writes the text to the cursor.
Quoted 11 lines
common/lcd.c static int do_lcd_clear(cmd_tbl_t *cmdtp, int
Quoted 11 lines
Signed-off-by Hannes Petermaier <[email protected]>--- common/lcd.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)common/lcd.c +0
-0@@ -279,12 +279,33 @@ static int do_lcd_clear(cmd_tbl_t *cmdtp, int
flag, int argc,
Quoted 24 lines
Quoted 24 lines
common/lcd.c +15
-0return 0 ; } +static int do_lcd_setcursor (cmd_tbl_t *cmdtp,int flag,int argc, +char *const argv[]) +{ +unsigned int col, row; + +if (argc !=3 ) +return CMD_RET_USAGE ; + + col =simple_strtoul (argv[1 ],NULL ,10 ); + row =simple_strtoul (argv[2 ],NULL ,10 ); +lcd_position_cursor (col, row); + +return 0 ; +} +U_BOOT_CMD ( cls,1 ,1 , do_lcd_clear,"clear screen" ,"" );
Quoted 8 lines
common/lcd.c static int do_lcd_clear(cmd_tbl_t *cmdtp, int flag, int argc, · line 308
Quoted 6 lines
common/lcd.c +6
-0+U_BOOT_CMD ( + setcurs,3 ,1 , do_lcd_setcursor, +"sets cursor for 'puts'" , +" <col> <row> in character" +); +I think it would be better if the
U_BOOT_CMDmacros were adjacent to the
functions they
Quoted 1 line
use. Also, I think this command is better suited for the
lcd_console.c
file.
You're maybe right. Only thing for decission was, that existing commands are allready defined withinlcd.c. But i've no problem to move it. What do you say? let's move?
Quoted 2 lines
Quoted 2 lines
/*----------------------------------------------------------------------*/
Quoted 7 lines
Quoted 3 lines
static int
lcd_init(void *lcdbase)Signature · 2 lines
Regards, Nikita Kiryanov
best regards,
Hannes
PATCH 2/21 common/lcd: Add command for setting cursor within lcd-framework
Hi Hannes,
Quoted 24 lines · Hannes Petermaier
"U-Boot" <[email protected]> schrieb am 01.02.2015 15:48:51:
Quoted 4 lines
From: Nikita Kiryanov <[email protected]>
To: Hannes Petermaier <[email protected]>, u-boot at lists.denx.de
Date: 01.02.2015 15:49
Subject: Re: [U-Boot] [PATCH 02/21] common/lcd: Add command for settingcursor
Quoted 4 lines
within lcd-framework
Sent by: "U-Boot" <[email protected]>Hi Hannes,
Hi Nikita,
Quoted 3 lines · Hannes Petermaier
Quoted 1 line
We need this function if we want to make some outputs i.e position the
writing
Quoted 3 lines
Quoted 1 line
cursor out of u-boot scripts.
This commit message is inaccurate. Positioning the writing cursor is not
in
Quoted 3 lines
itself output.
Also, what is the use case for such a command?
Quoted 8 lines
I want to set the "cursor" on the screen to a specific position and write there something
with "puts".For example:
setcurs 1 9; sets the cursor to first column and 9th row
puts "Hello World!" writes the text to the cursor.
Alright... So setcurs does not output anything, just prepares us to do output. I think that's how the commit message should be phrased.
Quoted 37 lines
Quoted 7 lines
Quoted 7 lines
Signed-off-by Hannes Petermaier <[email protected]>--- common/lcd.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)Quoted 5 lines
common/lcd.c static int do_lcd_clear(cmd_tbl_t *cmdtp, int
Quoted 5 lines
common/lcd.c +0
-0@@ -279,12 +279,33 @@ static int do_lcd_clear(cmd_tbl_t *cmdtp, intflag, int argc,
Quoted 24 lines
Quoted 24 lines
common/lcd.c +15
-0return 0 ; } +static int do_lcd_setcursor (cmd_tbl_t *cmdtp,int flag,int argc, +char *const argv[]) +{ +unsigned int col, row; + +if (argc !=3 ) +return CMD_RET_USAGE ; + + col =simple_strtoul (argv[1 ],NULL ,10 ); + row =simple_strtoul (argv[2 ],NULL ,10 ); +lcd_position_cursor (col, row); + +return 0 ; +} +U_BOOT_CMD ( cls,1 ,1 , do_lcd_clear,"clear screen" ,"" );
Quoted 3 lines
Quoted 3 lines
common/lcd.c static int do_lcd_clear(cmd_tbl_t *cmdtp, int flag, int argc, · line 305
Quoted 3 lines
common/lcd.c +3
-0+U_BOOT_CMD( + setcurs, 3, 1, do_lcd_setcursor, + "sets cursor for 'puts'",
Another thing: this function is not really limited to working with puts. It can do preparation for any other command that outputs to console. I recommend rewriting the description string to not mention it, maybe something along the lines of "set cursor on the screen".
Quoted 5 lines
Quoted 5 lines
common/lcd.c static int do_lcd_clear(cmd_tbl_t *cmdtp, int flag, int argc, · line 308
Quoted 3 lines
common/lcd.c +3
-0+" <col> <row> in character" +); +I think it would be better if the
U_BOOT_CMDmacros were adjacent to the
Quoted 7 lines
functions they
Quoted 1 line
use. Also, I think this command is better suited for the
lcd_console.cfile.
You're maybe right. Only thing for decission was, that existing commands are allready defined within
lcd.c.
That's ok; we should place code where it's most relevant, and your command is related to lcd console functionality.
Quoted 1 line
But i've no problem to move it. What do you say? let's move?
Yes, please move it to lcd_console.c
Signature · 2 lines
Regards, Nikita Kiryanov
PATCH 3/21 common/lcd: Add command for writing to lcd-display
In reply to Hannes PetermaierWe need this function if we want to make some outputs out of u-boot scripts.
--- common/lcd.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
common/lcd.c +17 -0
@@ -279,6 +279,17 @@ static int do_lcd_clear(cmd_tbl_t *cmdtp, int flag, int argc,return 0 ; } +static int do_lcd_puts (cmd_tbl_t *cmdtp,int flag,int argc, +char *const argv[]) +{ +if (argc !=2 ) +return CMD_RET_USAGE ; + +lcd_puts (argv[1 ]); + +return 0 ; +} +static int do_lcd_setcursor (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) {
@@ -306,6 +317,12 @@ U_BOOT_CMD(" <col> <row> in character" ); +U_BOOT_CMD ( + puts,2 ,1 , do_lcd_puts, +"print string on lcd-framebuffer" , +" <string>" +); +/*----------------------------------------------------------------------*/ static int lcd_init (void *lcdbase)
Signature · 1 line
1.7.9.5
PATCH 3/21 common/lcd: Add command for writing to lcd-display
Hi Hannes,
Quoted 2 lines · Hannes Petermaier
We need this function if we want to make some outputs out of u-boot scripts.
I think this commit message is missing information. What makes this necessary? Why can't your script use regular echo commands with the lcd console enabled?
Quoted 28 lines
Signed-off-by Hannes Petermaier <[email protected]>--- common/lcd.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)common/lcd.c +11
-0@@ -279,6 +279,17 @@ static int do_lcd_clear(cmd_tbl_t *cmdtp, int flag, int argc,return 0 ; } +static int do_lcd_puts (cmd_tbl_t *cmdtp,int flag,int argc, +char *const argv[]) +{ +if (argc !=2 ) +return CMD_RET_USAGE ; + +lcd_puts (argv[1 ]); + +return 0 ; +} +static int do_lcd_setcursor (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) {
common/lcd.c U_BOOT_CMD( · line 321
Quoted 5 lines
common/lcd.c +2
-0@@ -306,6 +317,12 @@ U_BOOT_CMD(" <col> <row> in character" ); +U_BOOT_CMD( + puts, 2, 1, do_lcd_puts,
"puts" is too generic for an lcd specific function. I would expect to see something with an "lcd" prefix. Also, this code seems better suited for lcd_console.c
Quoted 8 lines
common/lcd.c +4
-0+"print string on lcd-framebuffer" , +" <string>" +); +/*----------------------------------------------------------------------*/ static int lcd_init (void *lcdbase)
Signature · 2 lines
Regards, Nikita Kiryanov
PATCH 3/21 common/lcd: Add command for writing to lcd-display
Quoted 4 lines
From: Nikita Kiryanov <[email protected]>
To: Hannes Petermaier <[email protected]>, u-boot at lists.denx.de
Date: 01.02.2015 15:53
Subject: Re: [U-Boot] [PATCH 03/21] common/lcd: Add command for writing
to lcd-display
Quoted 3 lines
Sent by: "U-Boot" <[email protected]>
Hi Hannes,
Hi Nikita,
Quoted 3 lines · Hannes Petermaier
Quoted 1 line
We need this function if we want to make some outputs out of u-boot
scripts.
Quoted 3 lines
Quoted 1 line
I think this commit message is missing information. What makes this
necessary?
Quoted 1 line
Why can't your script use regular echo commands with the lcd console
enabled?
Since i don't want that stdout is redirected to LCD (customer isn't interested in watching
all output of u-boot) i need something to write out of scripts to the screen.
For example we write of script in which mode we are booting, maybe also some default ip settings
in recovery mode.
Quoted 11 lines
common/lcd.c static int do_lcd_clear(cmd_tbl_t *cmdtp, int
Quoted 11 lines
Signed-off-by Hannes Petermaier <[email protected]>--- common/lcd.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)common/lcd.c +0
-0@@ -279,6 +279,17 @@ static int do_lcd_clear(cmd_tbl_t *cmdtp, int
flag, int argc,
Quoted 21 lines
Quoted 21 lines
common/lcd.c +11
-0return 0 ; } +static int do_lcd_puts (cmd_tbl_t *cmdtp,int flag,int argc, +char *const argv[]) +{ +if (argc !=2 ) +return CMD_RET_USAGE ; + +lcd_puts (argv[1 ]); + +return 0 ; +} +static int do_lcd_setcursor (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) {@@ -306,6 +317,12 @@ U_BOOT_CMD(" <col> <row> in character" );
Quoted 4 lines
common/lcd.c U_BOOT_CMD( · line 321
Quoted 2 lines
common/lcd.c +2
-0+U_BOOT_CMD( + puts, 2, 1, do_lcd_puts,"puts" is too generic for an lcd specific function. I would expect to
see something
Quoted 1 line
with an "lcd" prefix. Also, this code seems better suited for
lcd_console.c
Okay, thats right - should we rename it to "lcdputs" ?
Only thing for decission was, that existing commands are allready defined withinlcd.c. But i've no problem to move it. What do you say? let's move?
Quoted 6 lines
common/lcd.c U_BOOT_CMD( · line 327
Quoted 6 lines
common/lcd.c +4
-0+"print string on lcd-framebuffer" , +" <string>" +); +
/*----------------------------------------------------------------------*/
Quoted 7 lines
Quoted 3 lines
common/lcd.c +0
-0static int lcd_init (void *lcdbase)Signature · 2 lines
Regards, Nikita Kiryanov
best regards,
Hannes
PATCH 3/21 common/lcd: Add command for writing to lcd-display
Hi Hannes,
Quoted 21 lines · Hannes Petermaier
Quoted 4 lines
From: Nikita Kiryanov <[email protected]>
To: Hannes Petermaier <[email protected]>, u-boot at lists.denx.de
Date: 01.02.2015 15:53
Subject: Re: [U-Boot] [PATCH 03/21] common/lcd: Add command for writingto lcd-display
Quoted 3 lines
Sent by: "U-Boot" <[email protected]>
Hi Hannes,
Hi Nikita,
Quoted 3 lines · Hannes Petermaier
Quoted 1 line
We need this function if we want to make some outputs out of u-boot
scripts.
Quoted 3 lines
Quoted 1 line
I think this commit message is missing information. What makes this
necessary?
Quoted 1 line
Why can't your script use regular echo commands with the lcd console
enabled?
Quoted 8 lines
Since i don't want that stdout is redirected to LCD (customer isn't interested in watching
all output of u-boot) i need something to write out of scripts to the screen.For example we write of script in which mode we are booting, maybe also some default ip settings
in recovery mode.
Alright, then please explain in the commit message that this function is meant to give user the option to output to lcd without enabling lcd console.
Quoted 38 lines
Quoted 7 lines
Quoted 7 lines
Signed-off-by Hannes Petermaier <[email protected]>--- common/lcd.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)Quoted 5 lines
common/lcd.c static int do_lcd_clear(cmd_tbl_t *cmdtp, int
Quoted 5 lines
common/lcd.c +0
-0@@ -279,6 +279,17 @@ static int do_lcd_clear(cmd_tbl_t *cmdtp, intflag, int argc,
Quoted 21 lines
Quoted 21 lines
common/lcd.c +11
-0return 0 ; } +static int do_lcd_puts (cmd_tbl_t *cmdtp,int flag,int argc, +char *const argv[]) +{ +if (argc !=2 ) +return CMD_RET_USAGE ; + +lcd_puts (argv[1 ]); + +return 0 ; +} +static int do_lcd_setcursor (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) {@@ -306,6 +317,12 @@ U_BOOT_CMD(" <col> <row> in character" );Quoted 4 lines
common/lcd.c U_BOOT_CMD( · line 321
Quoted 2 lines
common/lcd.c +2
-0+U_BOOT_CMD( + puts, 2, 1, do_lcd_puts,"puts" is too generic for an lcd specific function. I would expect to
Quoted 5 lines
see something
Quoted 1 line
with an "lcd" prefix. Also, this code seems better suited for
lcd_console.cOkay, thats right - should we rename it to "lcdputs" ?
That sounds better, yes.
Quoted 4 lines
Only thing for decission was, that existing commands are allready defined within
lcd.c.
That's ok; we should place code where it's most relevant, and your command is related to lcd console functionality.
Quoted 1 line
But i've no problem to move it. What do you say? let's move?
Yes, please move it to lcd_console.c
Signature · 2 lines
Regards, Nikita Kiryanov
PATCH 4/21 board/BuR/common: Take usage of am335x LCD-Display
In reply to Hannes PetermaierFrom now we use the am335x lcd driver and setup a display with displaying a summary screen to the lcd.
Values are taken from environment and or devicetree blob.
--- board/BuR/common/bur_common.h | 4 + board/BuR/common/common.c | 417 ++++++++++++++++++++++++++++++++++++++++- board/BuR/tseries/board.c | 52 +++-- include/configs/tseries.h | 8 + include/power/tps65217.h | 1 + 5 files changed, 463 insertions(+), 19 deletions(-)
board/BuR/common/bur_common.h +4 -0
@@ -12,6 +12,10 @@#ifndef _BUR_COMMON_H_#define _BUR_COMMON_H_ +#include <../../../drivers/video/am335x-fb.h> + +int load_lcdtiming (struct am335x_lcdpanel *panel); +void br_summaryscreen (void );void blink (u32 blinks,u32 intervall,u32 pin);void pmicsetup (u32 mpupll);void enable_uart0_pin_mux (void );
board/BuR/common/common.c +416 -1
445 lines not on this page · raw message
board/BuR/tseries/board.c +34 -18
78 lines not on this page · raw message
include/configs/tseries.h +8 -0
@@ -14,6 +14,12 @@#include <configs/bur_am335x_common.h> /* ------------------------------------------------------------------------- */ +#define CONFIG_AM335X_LCD +#define CONFIG_LCD +#define CONFIG_LCD_NOSTDOUT +#define CONFIG_SYS_WHITE_ON_BLACK +#define LCD_BPP LCD_COLOR32 +/* Clock Defines */ #define V_OSCK 26000000/* Clock output from T2 */ #define V_SCLK (V_OSCK)
@@ -22,6 +28,8 @@/* Support both device trees and ATAGs. */ #define CONFIG_OF_LIBFDT +#define CONFIG_USE_FDT /* use fdt within board code */ +#define CONFIG_OF_BOARD_SETUP #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG
include/power/tps65217.h +1 -0
@@ -73,6 +73,7 @@ enum {#define TPS65217_LDO_VOLTAGE_OUT_1_8 0x06#define TPS65217_LDO_VOLTAGE_OUT_3_3 0x1F +#define TPS65217_PWR_OFF 0x80#define TPS65217_PWR_SRC_USB_BITMASK 0x4#define TPS65217_PWR_SRC_AC_BITMASK 0x8
Signature · 1 line
1.7.9.5
PATCH 5/21 board/BuR/common: try to setup cpsw mac-address from the devicetree
In reply to Hannes Petermaiersince we have a dtb blob programmed on the board we try to setup the cpsw interface with the programmed mac.
If this method fails, we fall back to the device-fuses.
--- board/BuR/common/common.c | 25 +++++++++++++++---------- 1 file changed, 15 insertions(+), 10 deletions(-)
board/BuR/common/common.c +15 -10
@@ -591,9 +591,9 @@ static struct cpsw_platform_data cpsw_data = {int board_eth_init (bd_t *bis) {int rv =0 ; -uint8_t mac_addr[6 ]; +char mac_addr[6 ]; +const char *mac =0 ;uint32_t mac_hi, mac_lo; -/* try reading mac address from efuse */ mac_lo =readl (&cdev->macid0l); mac_hi =readl (&cdev->macid0h);
@@ -607,14 +607,19 @@ int board_eth_init(bd_t *bis)#if (defined(CONFIG_DRIVER_TI_CPSW ) && !defined(CONFIG_SPL_BUILD )) || \ (defined(CONFIG_SPL_ETH_SUPPORT ) && defined(CONFIG_SPL_BUILD ))if (!getenv ("ethaddr" )) { -printf ("<ethaddr> not set. Validating first E-fuse MAC ... " ); - -if (is_valid_ether_addr (mac_addr)) { -printf ("using: %02X:%02X:%02X:%02X:%02X:%02X.\n" , - mac_addr[0 ], mac_addr[1 ], mac_addr[2 ], - mac_addr[3 ], mac_addr[4 ], mac_addr[5 ] - ); -eth_setenv_enetaddr ("ethaddr" , mac_addr); +#if !defined(CONFIG_SPL_BUILD ) && defined(CONFIG_USE_FDT ) +printf ("<ethaddr> not set. trying DTB ... " ); + mac =dtbmacaddr (0 ); +#endif +if (!mac) { +printf ("<ethaddr> not set. validating E-fuse MAC ... " ); +if (is_valid_ether_addr ((const u8 *)mac_addr)) + mac = (const char *)mac_addr; + } + +if (mac) { +printf ("using: %pM on " , mac); +eth_setenv_enetaddr ("ethaddr" , (const u8 *)mac); } }writel (MII_MODE_ENABLE , &cdev->miisel);
Signature · 1 line
1.7.9.5
PATCH 6/21 board/BuR/tseries: Enable HW-Watchdog
In reply to Hannes Petermaier--- board/BuR/tseries/board.c | 4 ++++ include/configs/tseries.h | 3 +++ 2 files changed, 7 insertions(+)
board/BuR/tseries/board.c +4 -0
@@ -28,6 +28,7 @@#include <power/tps65217.h> #include "../common/bur_common.h" #include <lcd.h> +#include <watchdog.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -144,6 +145,9 @@ void sdram_init(void)/* Basic board specific setup. Pinmux has been handled already. */ int board_init (void ) { +#if defined(CONFIG_HW_WATCHDOG ) +hw_watchdog_init (); +#endif gd->bd->bi_boot_params =CONFIG_SYS_SDRAM_BASE +0x100 ;#ifdef CONFIG_NAND gpmc_init ();
include/configs/tseries.h +3 -0
@@ -20,6 +20,9 @@#define CONFIG_SYS_WHITE_ON_BLACK #define LCD_BPP LCD_COLOR32 +#define CONFIG_HW_WATCHDOG +#define CONFIG_OMAP_WATCHDOG +#define CONFIG_SPL_WATCHDOG_SUPPORT /* Clock Defines */ #define V_OSCK 26000000/* Clock output from T2 */ #define V_SCLK (V_OSCK)
Signature · 1 line
1.7.9.5
PATCH 7/21 board/BuR/tseries: Enable U-Boot BOOTCOUNT feature
In reply to Hannes Petermaier--- include/configs/tseries.h | 4 ++++ 1 file changed, 4 insertions(+)
include/configs/tseries.h +4 -0
@@ -23,6 +23,10 @@#define CONFIG_HW_WATCHDOG #define CONFIG_OMAP_WATCHDOG #define CONFIG_SPL_WATCHDOG_SUPPORT +/* Bootcount using the RTC block */ +#define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000 +#define CONFIG_BOOTCOUNT_LIMIT +#define CONFIG_BOOTCOUNT_AM33XX /* Clock Defines */ #define V_OSCK 26000000/* Clock output from T2 */ #define V_SCLK (V_OSCK)
Signature · 1 line
1.7.9.5
PATCH 8/21 board/BuR/tseries: Enable EXT4 support
In reply to Hannes Petermaier--- include/configs/tseries.h | 4 ++++ 1 file changed, 4 insertions(+)
include/configs/tseries.h +4 -0
@@ -275,6 +275,10 @@#define CONFIG_DOS_PARTITION #define CONFIG_CMD_FAT #define CONFIG_FAT_WRITE +#define CONFIG_FS_EXT4 +#define CONFIG_EXT4_WRITE +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_EXT4_WRITE #define CONFIG_CMD_FS_GENERIC #endif /* CONFIG_MMC, ... */
Signature · 1 line
1.7.9.5
PATCH 9/21 board/BuR/tseries: Change pinmux for GPIO2_28 from GPIO to PWM-Timeroutput
In reply to Hannes PetermaierFrom now we use this pin for the Brightness regulation from LED-Backlight.
--- board/BuR/tseries/mux.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
board/BuR/tseries/mux.c +3 -3
@@ -131,9 +131,9 @@ static struct module_pin_mux gpIOs[] = { {OFFSET(spi0_cs1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},/* TIMER5 (MMC0_DAT3) - TIMER5 (Buzzer) */ {OFFSET(mmc0_dat3), (MODE(3) | PULLUDEN | RXACTIVE)}, -/* TIMER6 (MMC0_DAT2) - PWM_BACK_3V3, later used as MODE3 for PWM */ - {OFFSET(mmc0_dat2), (MODE(7) | PULLUDEN | RXACTIVE)}, -/* GPIO2_27 (MMC0_DAT1) - MII_nNAND */ +/* TIMER6 (MMC0_DAT2) - PWM_BACK_3V3 */ + {OFFSET(mmc0_dat2), (MODE(3) | PULLUDEN | RXACTIVE)}, +/* GPIO2_28 (MMC0_DAT1) - MII_nNAND */ {OFFSET(mmc0_dat1), (MODE(7) | PULLUDEN | RXACTIVE)},/* GPIO2_29 (MMC0_DAT0) - NAND_1n0 */ {OFFSET(mmc0_dat0), (MODE(7) | PULLUDEN | RXACTIVE)},
Signature · 1 line
1.7.9.5
PATCH 10/21 board/BuR/tseries: Chg pinmux - use free NAND Pins in non NAND-config as GPIO
In reply to Hannes PetermaierOn boards were we have no NAND-flash soldered, we want to use those free pins as regular gpio.
--- board/BuR/tseries/mux.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
board/BuR/tseries/mux.c +8 -1
@@ -168,7 +168,14 @@ static struct module_pin_mux gpIOs[] = { {OFFSET(mcasp0_axr0), (MODE(7) | PULLUDDIS) },/* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */ {OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) }, - +#ifndef CONFIG_NAND + /* GPIO2_3 - NAND_OE */ + {OFFSET(gpmc_oen_ren), (MODE(7) | PULLDOWN_EN | RXACTIVE)}, +/* GPIO2_4 - NAND_WEN */ + {OFFSET(gpmc_wen), (MODE(7) | PULLDOWN_EN | RXACTIVE)}, +/* GPIO2_5 - NAND_BE_CLE */ + {OFFSET(gpmc_be0n_cle), (MODE(7) | PULLDOWN_EN | RXACTIVE)}, +#endif {-1}, };
Signature · 1 line
1.7.9.5
PATCH 11/21 board/BuR/tseries: Chg Pinmux - enable UART1 pins
In reply to Hannes Petermaier--- board/BuR/tseries/mux.c | 8 ++++++++ 1 file changed, 8 insertions(+)
board/BuR/tseries/mux.c +8 -0
@@ -25,6 +25,13 @@ static struct module_pin_mux uart0_pin_mux[] = { {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, {-1}, }; +static struct module_pin_mux uart1_pin_mux[] = { +/* UART0_RXD */ + {OFFSET (uart1_rxd), (MODE (0 ) |PULLUDEN |PULLUP_EN |RXACTIVE )}, +/* UART0_TXD */ + {OFFSET (uart1_txd), (MODE (0 ) |PULLUDEN )}, + {-1 }, +};#ifdef CONFIG_MMC static struct module_pin_mux mmc1_pin_mux[] = { {OFFSET(gpmc_ad7), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT7 */
@@ -236,5 +243,6 @@ void enable_board_pin_mux(void)#endif configure_module_pin_mux (spi0_pin_mux);configure_module_pin_mux (lcd_pin_mux); +configure_module_pin_mux (uart1_pin_mux);configure_module_pin_mux (gpIOs); }
Signature · 1 line
1.7.9.5
PATCH 12/21 board/BuR/common: Introduce Network Console and common environment for it
In reply to Hannes PetermaierIt is often necessary to "break in" into boards bootloader commandline if something fails or even for development purposes some parameters have to be changed.
So we enable u-boot's CONFIG_NETCONSOLE feature.
We also modify Networksettings to apply with this new use-case.
--- include/configs/bur_am335x_common.h | 23 +++++++++++++++++++++-- include/configs/tseries.h | 33 ++++----------------------------- 2 files changed, 25 insertions(+), 31 deletions(-)
include/configs/bur_am335x_common.h +21 -2
@@ -12,6 +12,23 @@#ifndef __BUR_AM335X_COMMON_H__#define __BUR_AM335X_COMMON_H__/* ------------------------------------------------------------------------- */ +#define BUR_COMMON_ENV \ +"defaultip=192.168.60.253\0" \ +"defaultsip=192.168.60.254\0" \ +"netconsole=echo switching to network console ...; " \ +"if dhcp; then " \ +"setenv ncip ${serverip}; else " \ +"setenv ncip 192.168.60.254; " \ +"setenv serverip 192.168.60.254; " \ +"setenv gatewayip 192.168.60.254; " \ +"setenv ipaddr 192.168.60.1; " \ +"fi;" \ +"setenv netdisplay0 '" \ +"setcurs 1 9; puts myip; setcurs 10 9; puts ${ipaddr};" \ +"setcurs 1 10;puts serverip; setcurs 10 10; puts ${serverip}\;'" \ +"run netdisplay0; " \ +"setenv stdout nc;setenv stdin nc;setenv stderr nc\0" +#define CONFIG_SYS_GENERIC_BOARD #define CONFIG_AM33XX
@@ -47,7 +64,7 @@#define CONFIG_BOOTP_SEND_HOSTNAME #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_NET_RETRY_COUNT 4 +#define CONFIG_NET_RETRY_COUNT 2#define CONFIG_CMD_PING #define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */ #define CONFIG_MII /* Required in net/eth.c */
@@ -57,7 +74,9 @@#define CONFIG_SPL_NET_SUPPORT #define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */ #define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" - +/* Network console */ +#define CONFIG_NETCONSOLE 1 +#define CONFIG_BOOTP_MAY_FAIL /* if we don't have DHCP environment */ /* * SPL related defines. The Public RAM memory map the ROM defines the * area between 0x402F0400 and 0x4030B800 as a download area and
include/configs/tseries.h +4 -29
@@ -125,35 +125,10 @@#ifndef CONFIG_SPL_BUILD #define CONFIG_EXTRA_ENV_SETTINGS \ - "autoload=0\0" \ - "loadaddr=0x80200000\0" \ - "bootfile=zImage\0" \ - "console=ttyO0,115200n8\0" \ - "optargs=\0" \ - "rootpath=/tftpboot/tseries/rootfs-small\0" \ - "nfsopts=nolock\0" \ - "netargs=setenv bootargs console=${console} " \ - "${optargs} " \ - "root=/dev/nfs " \ - "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ - "ip=dhcp\0" \ - "netboot=echo Booting from network ...; " \ - "setenv autoload no; " \ - "dhcp; " \ - "tftp ${loadaddr} ${bootfile}; " \ - "run netargs; " \ - "bootm ${loadaddr}\0" \ - "usbupdate=echo Updating UBOOT from USB-Stick ...; " \ - "usb start; " \ - "fatload usb 0 0x80000000 updateubootusb.img; " \ - "source;\0" \ - "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ - "setenv autoload 0; " \ - "dhcp;" \ - "tftp 0x80000000 updateUBOOT.img;" \ - "source;\0" \ - NANDARGS \ - MMCARGS +BUR_COMMON_ENV \ +"autoload=0\0" \ +NANDARGS \ +MMCARGS#endif /* !CONFIG_SPL_BUILD*/ #define CONFIG_BOOTCOMMAND \
Signature · 1 line
1.7.9.5
PATCH 13/21 board/BuR/common: Enable CONFIG_CMD_TIME
In reply to Hannes Petermaiertime measurement of u-boot commands is needed very often during development. We add this feature until development is completed. Maybe forever :)
--- include/configs/bur_am335x_common.h | 1 + 1 file changed, 1 insertion(+)
include/configs/bur_am335x_common.h +1 -0
@@ -29,6 +29,7 @@"run netdisplay0; " \ "setenv stdout nc;setenv stdin nc;setenv stderr nc\0" +#define CONFIG_CMD_TIME #define CONFIG_SYS_GENERIC_BOARD #define CONFIG_AM33XX
Signature · 1 line
1.7.9.5
PATCH 14/21 board/BuR/common: Add support for displaying BMP on LCD
In reply to Hannes PetermaierCustomer wants to display some logo very quickly after power on, so we support from now loading a compressed bmp.gz to the screen.
--- include/configs/bur_am335x_common.h | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
include/configs/bur_am335x_common.h +8 -1
@@ -30,6 +30,13 @@ "setenv stdout nc;setenv stdin nc;setenv stderr nc\0"#define CONFIG_CMD_TIME +#define CONFIG_VIDEO_BMP_GZIP +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (1366*767*4) +#define CONFIG_CMD_UNZIP +#define CONFIG_CMD_BMP +#define CONFIG_BMP_24BMP +#define CONFIG_BMP_32BPP +#define CONFIG_SYS_GENERIC_BOARD #define CONFIG_AM33XX
@@ -130,7 +137,7 @@* we are on so we do not need to rely on the command prompt. We set a * console baudrate of 115200 and use the default baud rate table. */ -#define CONFIG_SYS_MALLOC_LEN (1024 << 10) +#define CONFIG_SYS_MALLOC_LEN (5120 << 10)#define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT "U-Boot (BuR V2.0)# "#define CONFIG_SYS_CONSOLE_INFO_QUIET
Signature · 1 line
1.7.9.5
PATCH 15/21 board/BuR/tseries: Rework default-environment settings.
In reply to Hannes PetermaierDue to several changes of the boot-process we've redesigned the default- environment settings completly.
--- include/configs/tseries.h | 71 +++++++++++++++++++++++++++++++++++++++++---- 1 file changed, 66 insertions(+), 5 deletions(-)
include/configs/tseries.h +66 -5
@@ -94,8 +94,8 @@#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000#endif /* CONFIG_NAND */ -/* Always 128 KiB env size */ -#define CONFIG_ENV_SIZE (128 << 10) +/* Always 64 KiB env size */ +#define CONFIG_ENV_SIZE (64 << 10)#ifdef CONFIG_NAND #define NANDARGS \
@@ -118,7 +118,32 @@#ifdef CONFIG_MMC #define MMCARGS \ - "silent=1\0" +"dtbdev=mmc\0" \ +"dtbpart=0:1\0" \ +"logo0=ext4load mmc 0:3 ${loadaddr} /PPTLogo.bmp.gz && " \ + "bmp display ${loadaddr} 0 0\0" \ +"logo1=ext4load mmc 0:1 ${loadaddr} /PPTLogo.bmp.gz && " \ + "bmp display ${loadaddr} 0 0\0" \ +"mmcroot0=setenv bootargs ${optargs} console=${console}\0" \ +"mmcroot1=setenv bootargs ${optargs} console=${console} root=/dev/mmcblk0p2 " \ + "rootfstype=ext4\0" \ +"mmcboot0=echo booting Updatesystem from mmc (ext4-fs) ...; " \ + "ext4load mmc 0:1 ${loadaddr} /${kernel}; " \ + "ext4load mmc 0:1 ${ramaddr} /${ramdisk}; " \ + "run mmcroot0; bootz ${loadaddr} ${ramaddr} ${dtbaddr};\0" \ +"mmcboot1=echo booting PPT-OS from mmc (ext4-fs) ...; " \ + "ext4load mmc 0:2 ${loadaddr} /boot/${kernel}; " \ + "run mmcroot1; bootz ${loadaddr} - ${dtbaddr};\0" \ +"defboot=run logo0 || run logo1; " \ + "ext4load mmc 0:2 ${loadaddr} /boot/PPTImage.md5 && run mmcboot1; " \ + "ext4load mmc 0:1 ${dtbaddr} /$dtb && run mmcboot0; " \ + "run ramboot; run usbupdate;\0" \ +"bootlimit=1\0" \ +"altbootcmd=run logo0 || run logo1; " \ + "run mmcboot0;\0" \ +"upduboot=dhcp; " \ + "tftp ${loadaddr} MLO && mmc write ${loadaddr} 100 100; " \ + "tftp ${loadaddr} u-boot.img && mmc write ${loadaddr} 300 400;\0"#else #define MMCARGS ""#endif /* CONFIG_MMC */
@@ -126,14 +151,50 @@#ifndef CONFIG_SPL_BUILD #define CONFIG_EXTRA_ENV_SETTINGS \ BUR_COMMON_ENV \ +"verify=no\0" \ "autoload=0\0" \ +"dtb=bur-ppt-ts30.dtb\0" \ +"dtbaddr=0x80100000\0" \ +"loadaddr=0x80200000\0" \ +"ramaddr=0x80A00000\0" \ +"kernel=zImage\0" \ +"ramdisk=rootfs.cpio.uboot\0" \ +"console=ttyO0,115200n8\0" \ +"optargs=consoleblank=0 quiet lpj=1191936 panic=2\0" \ +"nfsroot=/tftpboot/tseries/rootfs-small\0" \ +"nfsopts=nolock\0" \ +"ramargs=setenv bootargs ${optargs} console=${console} root=/dev/ram0\0" \ +"netargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${nfsroot},${nfsopts} rw " \ + "ip=dhcp\0" \ +"netboot=echo Booting from network ...; " \ + "dhcp; " \ + "tftp ${loadaddr} ${kernel}; " \ + "tftp ${dtbaddr} ${dtb}; " \ + "run netargs; " \ + "bootz ${loadaddr} - ${dtbaddr}\0" \ +"ramboot=echo Booting from network into RAM ...; "\ + "if dhcp; then; " \ + "tftp ${loadaddr} ${kernel}; " \ + "tftp ${ramaddr} ${ramdisk}; " \ + "if ext4load ${dtbdev} ${dtbpart} ${dtbaddr} /${dtb}; " \ + "then; else tftp ${dtbaddr} ${dtb}; fi;" \ + "run mmcroot0; " \ + "bootz ${loadaddr} ${ramaddr} ${dtbaddr}; fi;\0" \ +"usbupdate=echo Updating UBOOT from USB-Stick ...; " \ + "usb start && fatload usb 0 0x80000000 updateubootusb.img && source\0" \ +"netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ + "setenv autoload 0; " \ + "dhcp && tftp 0x80000000 updateUBOOT.img && source;\0" \ NANDARGS \ MMCARGS#endif /* !CONFIG_SPL_BUILD*/ #define CONFIG_BOOTCOMMAND \ - "run mmcboot1;" -#define CONFIG_BOOTDELAY 1/* TODO: f?r release auf 0 setzen */ + "run defboot;" +#define CONFIG_BOOTDELAY 0#ifdef CONFIG_NAND /*
Signature · 1 line
1.7.9.5
PATCH 16/21 board/BuR/tseries: cosmetic changes
In reply to Hannes Petermaierremove unnary '#define ETHLED_ORANGE (96+16) /* GPIO3_16 */'
--- board/BuR/tseries/board.c | 2 -- 1 file changed, 2 deletions(-)
board/BuR/tseries/board.c +0 -2
@@ -34,10 +34,8 @@ DECLARE_GLOBAL_DATA_PTR;/* --------------------------------------------------------------------------*/ /* -- defines for GPIO -- */ -#define ETHLED_ORANGE (96+16)/* GPIO3_16 */ #define REPSWITCH (0+20)/* GPIO0_20 */ -#if defined(CONFIG_SPL_BUILD )/* TODO: check ram-timing ! */ static const struct ddr_data ddr3_data = {
Signature · 1 line
1.7.9.5
PATCH 17/21 board/BuR/kwb: switch to board HW-Rev3
In reply to Hannes PetermaierThe board has been redesigned, therefore we need from now other I/O Pins to mux and handle.
Older boards aren't supported from now anymore.
--- board/BuR/kwb/board.c | 92 ++++++++++++++++++++++++++++++------------------- board/BuR/kwb/mux.c | 51 +++++++++++++-------------- include/configs/kwb.h | 9 +++-- 3 files changed, 89 insertions(+), 63 deletions(-)
board/BuR/kwb/board.c +56 -36
@@ -26,14 +26,13 @@#include <i2c.h> #include <power/tps65217.h> #include "../common/bur_common.h" +#include <lcd.h> /* -------------------------------------------------------------------------*/ /* -- defines for used GPIO Hardware -- */ -#define KEY (0+4) -#define LCD_PWR (0+5) -#define PUSH_KEY (0+31) -#define USB2SD_NRST (32+29) -#define USB2SD_PWR (96+13) +#define ESC_KEY (0+19) +#define LCD_PWR (0+5) +#define PUSH_KEY (0+31)/* -------------------------------------------------------------------------*/ /* -- PSOC Resetcontroller Register defines -- */
@@ -46,6 +45,7 @@/* -- defines for RSTCTRL_CTRLREG -- */ #define RSTCTRL_FORCE_PWR_NEN 0x0404 +#define RSTCTRL_CAN_STB 0x4040#if defined(CONFIG_SPL_BUILD )/* TODO: check ram-timing ! */
@@ -107,10 +107,13 @@ void am33xx_spl_board_init(void) &cmper->epwmss0clkctrl, &cmper->epwmss1clkctrl, &cmper->epwmss2clkctrl, + &cmper->lcdclkctrl, + &cmper->lcdcclkstctrl, 0 };do_enable_clocks (clk_domains, clk_modules_kwbspecific,1 ); - +/* setup LCD-Pixel Clock */ +writel (0x2 ,CM_DPLL +0x34 );/* power-OFF LCD-Display */ gpio_direction_output (LCD_PWR ,0 );
@@ -121,7 +124,7 @@ void am33xx_spl_board_init(void)/* power-ON 3V3 via Resetcontroller */ oldspeed =i2c_get_bus_speed ();if (i2c_set_bus_speed (CONFIG_SYS_OMAP24_I2C_SPEED_PSOC ) >=0 ) { - buf =RSTCTRL_FORCE_PWR_NEN ; + buf =RSTCTRL_FORCE_PWR_NEN |RSTCTRL_CAN_STB ;i2c_write (RSTCTRL_ADDR ,RSTCTRL_CTRLREG ,1 , (uint8_t *)&buf,sizeof (buf));i2c_set_bus_speed (oldspeed);
@@ -129,15 +132,6 @@ void am33xx_spl_board_init(void)puts ("ERROR: i2c_set_bus_speed failed! (turn on PWR_nEN)\n" ); } -#if defined(CONFIG_AM335X_USB0 ) -/* power on USB2SD Controller */ -gpio_direction_output (USB2SD_PWR ,1 ); -mdelay (1 ); -/* give a reset Pulse to USB2SD Controller */ -gpio_direction_output (USB2SD_NRST ,0 ); -mdelay (1 ); -gpio_set_value (USB2SD_NRST ,1 ); -#endif pmicsetup (0 ); }
@@ -166,7 +160,6 @@ int board_init(void)#ifdef CONFIG_BOARD_LATE_INIT int board_late_init (void ) { -const unsigned int ton =250 ;const unsigned int toff =1000 ;unsigned int cnt =3 ;unsigned short buf =0xAAAA ;
@@ -175,50 +168,77 @@ int board_late_init(void)tps65217_reg_write (TPS65217_PROT_LEVEL_NONE ,TPS65217_WLEDCTRL2 ,0x32 ,0xFF );/* 50% dimlevel */ -if (gpio_get_value (KEY )) { +if (gpio_get_value (ESC_KEY )) {do { -/* turn on light */ -tps65217_reg_write (TPS65217_PROT_LEVEL_NONE , -TPS65217_WLEDCTRL1 ,0x09 ,0xFF ); -mdelay (ton); -/* turn off light */ -tps65217_reg_write (TPS65217_PROT_LEVEL_NONE , -TPS65217_WLEDCTRL1 ,0x01 ,0xFF ); +lcd_position_cursor (1 ,8 ); +switch (cnt) { +case 3 : +lcd_puts ( +"release ESC-KEY to enter SERVICE-mode." ); +break ; +case 2 : +lcd_puts ( +"release ESC-KEY to enter DIAGNOSE-mode." ); +break ; +case 1 : +lcd_puts ( +"release ESC-KEY to enter BOOT-mode. " ); +break ; + }mdelay (toff); cnt--; -if (!gpio_get_value (KEY ) && +if (!gpio_get_value (ESC_KEY ) && +gpio_get_value (PUSH_KEY ) &&2 == cnt) { +lcd_position_cursor (1 ,8 ); +lcd_puts ( +"switching to network-console ... " ); +setenv ("bootcmd" ,"run netconsole" ); + cnt =4 ; +break ; + }else if (!gpio_get_value (ESC_KEY ) &&gpio_get_value (PUSH_KEY ) &&1 == cnt) { -puts ("updating from USB ...\n" ); +lcd_position_cursor (1 ,8 ); +lcd_puts ( +"updating U-BOOT from USB ... " );setenv ("bootcmd" ,"run usbupdate" ); + cnt =4 ;break ; - }else if (!gpio_get_value (KEY )) { + }else if ((!gpio_get_value (ESC_KEY ) && +gpio_get_value (PUSH_KEY ) && cnt ==0 ) || + (gpio_get_value (ESC_KEY ) && +gpio_get_value (PUSH_KEY ) && cnt ==0 )) { +lcd_position_cursor (1 ,8 ); +lcd_puts ( +"starting script from network ... " ); +setenv ("bootcmd" ,"run netscript" ); + cnt =4 ; +break ; + }else if (!gpio_get_value (ESC_KEY )) {break ; } }while (cnt); } +lcd_position_cursor (1 ,8 );switch (cnt) {case 0 : -puts ("3 blinks ... entering BOOT mode.\n" ); +lcd_puts ("entering BOOT-mode. " ); +setenv ("bootcmd" ,"run defaultAR" ); buf =0x0000 ;break ;case 1 : -puts ("2 blinks ... entering DIAGNOSE mode.\n" ); +lcd_puts ("entering DIAGNOSE-mode. " ); buf =0x0F0F ;break ;case 2 : -puts ("1 blinks ... entering SERVICE mode.\n" ); +lcd_puts ("entering SERVICE mode. " ); buf =0xB4B4 ;break ;case 3 : -puts ("0 blinks ... entering RUN mode.\n" ); +lcd_puts ("loading OS... " ); buf =0x0404 ;break ; } -mdelay (ton); -/* turn on light */ -tps65217_reg_write (TPS65217_PROT_LEVEL_NONE , -TPS65217_WLEDCTRL1 ,0x09 ,0xFF );/* write bootinfo into scratchregister of resetcontroller */ oldspeed =i2c_get_bus_speed ();if (i2c_set_bus_speed (CONFIG_SYS_OMAP24_I2C_SPEED_PSOC ) >=0 ) {
board/BuR/kwb/mux.c +26 -25
93 lines not on this page · raw message
include/configs/kwb.h +7 -2
@@ -14,6 +14,11 @@#include <configs/bur_am335x_common.h> /* ------------------------------------------------------------------------- */ +#define CONFIG_AM335X_LCD +#define CONFIG_LCD +#define CONFIG_LCD_NOSTDOUT +#define CONFIG_SYS_WHITE_ON_BLACK +#define LCD_BPP LCD_COLOR32/* Clock Defines */ #define V_OSCK 26000000/* Clock output from T2 */ #define V_SCLK (V_OSCK)
@@ -87,8 +92,6 @@#undef CONFIG_BOOTM_NETBSD#undef CONFIG_BOOTM_PLAN9#undef CONFIG_BOOTM_RTEMS -#undef CONFIG_GZIP -#undef CONFIG_ZLIB/* USB configuration */ #define CONFIG_USB_MUSB_DSPS
@@ -100,6 +103,8 @@#define CONFIG_MUSB_HOST #define CONFIG_AM335X_USB0 #define CONFIG_AM335X_USB0_MODE MUSB_HOST +#define CONFIG_AM335X_USB1 +#define CONFIG_AM335X_USB1_MODE MUSB_HOST#ifdef CONFIG_MUSB_HOST #define CONFIG_CMD_USB
Signature · 1 line
1.7.9.5
PATCH 18/21 board/BuR/kwb: Support booting Linux
In reply to Hannes PetermaierFor series testing purpose we need to boot some linux, therefore we enable the needed features
- bootz
- devicetree
--- include/configs/kwb.h | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
include/configs/kwb.h +8 -1
@@ -88,10 +88,17 @@#define CONFIG_BOOTDELAY 1/* TODO: f?r release auf 0 setzen */ /* undefine command which we not need here */ -#undef CONFIG_BOOTM_LINUX#undef CONFIG_BOOTM_NETBSD#undef CONFIG_BOOTM_PLAN9#undef CONFIG_BOOTM_RTEMS +#undef CONFIG_CMD_CRC32 + +/* Support both device trees and ATAGs. */ +#define CONFIG_OF_LIBFDT +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_CMD_BOOTZ /* USB configuration */ #define CONFIG_USB_MUSB_DSPS
Signature · 1 line
1.7.9.5
PATCH 19/21 board/BuR/kwb: Redesign default-environment
In reply to Hannes PetermaierDue to several changes in the boot-process we do a complete redesign of the default environment.
--- include/configs/kwb.h | 81 +++++++++++++++++++++++++++---------------------- 1 file changed, 45 insertions(+), 36 deletions(-)
include/configs/kwb.h +45 -36
@@ -43,49 +43,58 @@#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200/* 256 KB */ #define CONFIG_SPL_MMC_SUPPORT -#undef CONFIG_SPL_OS_BOOT -#ifdef CONFIG_SPL_OS_BOOT -#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000 - -/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address 0x120000 */ -#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80/* address 0x10000 */ -#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ - -#endif /* CONFIG_SPL_OS_BOOT */ - -/* Always 128 KiB env size */ -#define CONFIG_ENV_SIZE (128 << 10) +/* Always 64 KiB env size */ +#define CONFIG_ENV_SIZE (64 << 10)#ifndef CONFIG_SPL_BUILD #define CONFIG_EXTRA_ENV_SETTINGS \ - "autoload=0\0" \ - "loadaddr=0x80100000\0" \ - "bootfile=arimg\0" \ - "usbboot=echo Booting from USB-Stick ...; " \ - "usb start; " \ - "fatload usb 0 ${loadaddr} ${bootfile}; " \ - "usb stop; " \ - "go ${loadaddr};\0" \ - "netboot=echo Booting from network ...; " \ - "setenv autoload 0; " \ - "dhcp; " \ - "tftp ${loadaddr} arimg; " \ - "go ${loadaddr}\0" \ - "usbupdate=echo Updating UBOOT from USB-Stick ...; " \ - "usb start; " \ - "fatload usb 0 0x80000000 updateubootusb.img; " \ - "source;\0" \ - "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ - "setenv autoload 0; " \ - "dhcp;" \ - "tftp 0x80000000 updateUBOOT.img;" \ - "source;\0" +BUR_COMMON_ENV \ +"vx_romfsbase=0x800E0000\0" \ +"vx_romfssize=0x20000\0" \ +"vx_memtop=0x8FBEF000\0" \ +"loadromfs=mmc read ${vx_romfsbase} 700 100\0" \ +"autoload=0\0" \ +"loadaddr=0x80100000\0" \ +"logoaddr=0x82000000\0" \ +"defaultARlen=0x8000\0" \ +"loaddefaultAR=mmc read ${loadaddr} 800 ${defaultARlen}\0" \ +"defaultAR=run loadromfs; run loaddefaultAR; go ${loadaddr}\0" \ +"logo0=fatload mmc 0:1 ${logoaddr} SYSTEM/ADDON/Bootlogo/Bootlogo.bmp.gz && " \ + "bmp display ${logoaddr} 0 0\0" \ +"logo1=fatload mmc 0:1 ${logoaddr} SYSTEM/BASE/Bootlogo/Bootlogo.bmp.gz && " \ + "bmp display ${logoaddr} 0 0\0" \ +"mmcboot=echo booting AR from eMMC-flash ...; "\ + "run logo0 || run logo1; " \ + "run loadromfs; " \ + "fatload mmc 0:1 ${loadaddr} arimg && go ${loadaddr}; " \ + "run defaultAR;\0" \ +"netboot=echo booting AR from network ...; " \ + "run loadromfs; " \ + "tftp ${loadaddr} arimg && go ${loadaddr}; " \ + "puts 'networkboot failed!';\0" \ +"usbupdate=echo updating u-boot from usb ...; " \ + "usb start; " \ + "fatload usb 0 0x80000000 updateubootusb.img && source; " \ + "puts 'usbupdate failed!'\0" \ +"netscript=echo running script from network (tftp) ...; " \ + "tftp 0x80000000 netscript.img && source; " \ + "puts 'netscript load failed!'\0" \ +"netupdate=tftp ${loadddr} MLO && mmc write ${loadaddr} 100 100; " \ + "tftp ${loadaddr} u-boot.img && mmc write ${loadaddr} 300 300\0" \ +"netupdatedefaultAR=echo updating defaultAR from network (tftp) ...; " \ + "if tftp 0x80100000 arimg.bin; " \ + "then mmc write 0x80100000 800 ${defaultARlen}; " \ + "else setcurs 1 8; puts 'defAR update failed (tftp)!'; fi;\0" \ +"netupdateROMFS=echo updating romfs from network (tftp) ...; " \ + "if tftp 0x80100000 romfs.bin; " \ + "then mmc write 0x80100000 700 100; " \ + "else setcurs 1 8; puts 'romfs update failed (tftp)!'; fi;\0" +#endif /* !CONFIG_SPL_BUILD*/ #define CONFIG_BOOTCOMMAND \ "run usbupdate;" -#define CONFIG_BOOTDELAY 1/* TODO: f?r release auf 0 setzen */ +#define CONFIG_BOOTDELAY 0/* undefine command which we not need here */ #undef CONFIG_BOOTM_NETBSD
Signature · 1 line
1.7.9.5
PATCH 20/21 board/BuR/kwb: Form a bootline for vxWorks
In reply to Hannes PetermaiervxWorks needs several parameters which are set by the bootloader und his environment. So we form a vxWorks bootline and pass the result to vxWorks on a predefined address.
--- board/BuR/kwb/board.c | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
board/BuR/kwb/board.c +30 -0
@@ -47,6 +47,12 @@#define RSTCTRL_FORCE_PWR_NEN 0x0404#define RSTCTRL_CAN_STB 0x4040 +#define VXWORKS_BOOTLINE 0x80001100 +#define DEFAULT_BOOTLINE "cpsw(0,0):pme/vxWorks" +#define VXWORKS_USER "u=vxWorksFTP pw=vxWorks tn=vxtarget" + +DECLARE_GLOBAL_DATA_PTR ; +#if defined(CONFIG_SPL_BUILD )/* TODO: check ram-timing ! */ static const struct ddr_data ddr3_data = {
@@ -248,6 +254,30 @@ int board_late_init(void) }else {puts ("ERROR: i2c_set_bus_speed failed! (scratchregister)\n" ); } +/* setup vxworks bootline */ +char *vxworksbootline = (char *)VXWORKS_BOOTLINE ; + +/* setup default IP, in case if there is nothing in environment */ +if (!getenv ("ipaddr" )) { +setenv ("ipaddr" ,"192.168.60.1" ); +setenv ("netmask" ,"255.255.255.0" ); +setenv ("serverip" ,"192.168.60.254" ); +setenv ("gatewayip" ,"192.168.60.254" ); +puts ("net: had no IP! made default setup.\n" ); + } + +sprintf (vxworksbootline, +"%s h=%s e=%s:%s g=%s %s o=0x%08x;0x%08x;0x%08x;0x%08x" , +DEFAULT_BOOTLINE , +getenv ("serverip" ), +getenv ("ipaddr" ),getenv ("netmask" ), +getenv ("gatewayip" ), +VXWORKS_USER , + (unsigned int ) gd->fb_base-0x20 , + (u32 )getenv_ulong ("vx_memtop" ,16 , gd->fb_base-0x20 ), + (u32 )getenv_ulong ("vx_romfsbase" ,16 ,0 ), + (u32 )getenv_ulong ("vx_romfssize" ,16 ,0 )); +/* * reset VBAR registers to its reset location, VxWorks 6.9.3.2 does * expect that vectors are there, original u-boot moves them to _start
Signature · 1 line
1.7.9.5
PATCH 21/21 board/BuR/kwb: Support modify bootcmd through reset-controller
In reply to Hannes PetermaierFor some cases it is necessary to modify temporaly the bootcommand. This can be done by writing into the Scratchregister a specific value:
* 0xCC - modify bootcmd "run netboot"
* 0xCD - modify bootcmd "run netscript"
* 0xCE - modify bootcmd "run mmcboot"
the environment in flash is NOT overwritten.
--- board/BuR/kwb/board.c | 30 ++++++++++++++++++++++++++++-- 1 file changed, 28 insertions(+), 2 deletions(-)
board/BuR/kwb/board.c +28 -2
@@ -169,10 +169,18 @@ int board_late_init(void)const unsigned int toff =1000 ;unsigned int cnt =3 ;unsigned short buf =0xAAAA ; +unsigned char scratchreg =0 ;unsigned int oldspeed; -tps65217_reg_write (TPS65217_PROT_LEVEL_NONE , -TPS65217_WLEDCTRL2 ,0x32 ,0xFF );/* 50% dimlevel */ +/* try to read out some boot-instruction from resetcontroller */ + oldspeed =i2c_get_bus_speed (); +if (i2c_set_bus_speed (CONFIG_SYS_OMAP24_I2C_SPEED_PSOC ) >=0 ) { +i2c_read (RSTCTRL_ADDR ,RSTCTRL_SCRATCHREG ,1 , + &scratchreg,sizeof (scratchreg)); +i2c_set_bus_speed (oldspeed); + }else { +puts ("ERROR: i2c_set_bus_speed failed! (scratchregister)\n" ); + }if (gpio_get_value (ESC_KEY )) { do {
@@ -223,6 +231,24 @@ int board_late_init(void)break ; } }while (cnt); + }else if (scratchreg ==0xCC ) { +lcd_position_cursor (1 ,8 ); +lcd_puts ( +"starting vxworks from network ... " ); +setenv ("bootcmd" ,"run netboot" ); + cnt =4 ; + }else if (scratchreg ==0xCD ) { +lcd_position_cursor (1 ,8 ); +lcd_puts ( +"starting script from network ... " ); +setenv ("bootcmd" ,"run netscript" ); + cnt =4 ; + }else if (scratchreg ==0xCE ) { +lcd_position_cursor (1 ,8 ); +lcd_puts ( +"starting AR from eMMC ... " ); +setenv ("bootcmd" ,"run mmcboot" ); + cnt =4 ; }lcd_position_cursor (1 ,8 );
Signature · 1 line
1.7.9.5