imx: mx6slevk add pmic support
v3 cover imx: mx6slevk add pmic support
This patch set is extracted from the previous "imx:mx6 add ldo bypass" patch set, with only one return value change.
patch 1/3 is add pad settings for I2C1
patch 2/3 is add I2C and PMIC support in board header file patch 3/3 is to add pmic support for mx6slevk.
patch 3/3 is from patch 3/12 in previous "imx:mx6 add ldo bypass" patch, with only one small change is return value.
Changes v3:
Take Fabio's suggestion, for patch 3/3, remove ret variable, and directly "return pfuze_mode_init(xxx)"
Changes v2:
Changing "return -EIO" to "return ret".
Peng Fan (3):
imx:mx6sl add I2c pad settings
imx:mx6slevk add pmic and i2c configuration
imx:mx6slevk implement power init board
arch/arm/include/asm/arch-mx6/mx6sl_pins.h | 5 ++++ board/freescale/mx6slevk/mx6slevk.c | 42 ++++++++++++++++++++++++++++++ include/configs/mx6slevk.h | 12 +++++++++ 3 files changed, 59 insertions(+)
Signature · 1 line
1.8.4
PATCH v3 1/3 imx:mx6sl add I2c pad settings
A few pad settings are I2C1
--- arch/arm/include/asm/arch-mx6/mx6sl_pins.h | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/include/asm/arch-mx6/mx6sl_pins.h +5 -0
@@ -58,5 +58,10 @@ enum {MX6_PAD_KEY_COL4__USB_USBOTG1_PWR =IOMUX_PAD (0x0484 ,0x017C ,6 ,0x0000 ,0 ,0 ),MX6_PAD_KEY_COL5__USB_USBOTG2_PWR =IOMUX_PAD (0x0488 ,0x0180 ,6 ,0x0000 ,0 ,0 ), + +MX6_PAD_I2C1_SDA__I2C1_SDA =IOMUX_PAD (0x0450 ,0x0160 ,0x10 ,0x0720 ,2 ,0 ), +MX6_PAD_I2C1_SDA__GPIO_3_13 =IOMUX_PAD (0x0450 ,0x0160 ,5 ,0x0000 ,0 ,0 ), +MX6_PAD_I2C1_SCL__I2C1_SCL =IOMUX_PAD (0x044C ,0x015C ,0x10 ,0x071C ,2 ,0 ), + MX6_PAD_I2C1_SCL__GPIO_3_12 = IOMUX_PAD(0x044C, 0x015C, 5, 0x0000, 0, 0), };#endif /* __ASM_ARCH_MX6_MX6SL_PINS_H__ */
Signature · 1 line
1.8.4
PATCH v3 1/3 imx:mx6sl add I2c pad settings
Quoted 4 lines · Peng Fan
A few pad settings are I2C1
Signed-off-by Peng Fan <[email protected]>---
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v3 2/3 imx:mx6slevk add pmic and i2c configuration
In reply to Peng FanAdd pmic and i2c configuration in board header file.
--- include/configs/mx6slevk.h | 12 ++++++++++++ 1 file changed, 12 insertions(+)
include/configs/mx6slevk.h +12 -0
@@ -48,6 +48,18 @@#define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION +/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_PFUZE100 +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 +#define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_MII
Signature · 1 line
1.8.4
PATCH v3 2/3 imx:mx6slevk add pmic and i2c configuration
Quoted 4 lines · Peng Fan
Add pmic and i2c configuration in board header file.
Signed-off-by Peng Fan <[email protected]>---
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v3 3/3 imx:mx6slevk implement power init board
In reply to Peng FanImplement power_init_board and related I2C interface configuration.
After adding this, uboot can successfully detect and configure pmic.
"
U-Boot 2015.01-00281-ge29eddf (Feb 12 2015 - 09:24:01)
CPU: Freescale i.MX6SL rev1.0 at 396 MHz Reset cause: POR Board: MX6SLEVK I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
"
--- board/freescale/mx6slevk/mx6slevk.c | 42 +++++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+)
board/freescale/mx6slevk/mx6slevk.c +42 -0
@@ -13,13 +13,18 @@#include <asm/arch/sys_proto.h> #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/mxc_i2c.h> #include <asm/imx-common/spi.h> #include <asm/io.h> #include <linux/sizes.h> #include <common.h> #include <fsl_esdhc.h> +#include <i2c.h> #include <mmc.h> #include <netdev.h> +#include <power/pmic.h> +#include <power/pfuze100_pmic.h> +#include "../common/pfuze.h" #include <usb.h> #include <usb/ehci-fsl.h>
@@ -40,6 +45,11 @@ DECLARE_GLOBAL_DATA_PTR;#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) +#define ETH_PHY_RESET IMX_GPIO_NR(4, 21)int dram_init (void )
@@ -221,6 +231,34 @@ int board_mmc_init(bd_t *bis)return 0 ; } +#ifdef CONFIG_SYS_I2C_MXC +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +/* I2C1 for PMIC */ +struct i2c_pads_info i2c_pad_info1 = { + .sda = { + .i2c_mode =MX6_PAD_I2C1_SDA__I2C1_SDA |PC , + .gpio_mode =MX6_PAD_I2C1_SDA__GPIO_3_13 |PC , + .gp =IMX_GPIO_NR (3 ,13 ), + }, + .scl = { + .i2c_mode =MX6_PAD_I2C1_SCL__I2C1_SCL |PC , + .gpio_mode =MX6_PAD_I2C1_SCL__GPIO_3_12 |PC , + .gp =IMX_GPIO_NR (3 ,12 ), + }, +}; + +int power_init_board (void ) +{ +struct pmic *p; + + p =pfuze_common_init (I2C_PMIC ); +if (!p) +return -ENODEV ; + +return pfuze_mode_init (p,APS_PFM ); +} +#endif +#ifdef CONFIG_FEC_MXC int board_eth_init (bd_t *bis) {
@@ -297,6 +335,10 @@ int board_init(void)/* address of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; +#ifdef CONFIG_SYS_I2C_MXC +setup_i2c (0 ,CONFIG_SYS_I2C_SPEED ,0x7f , &i2c_pad_info1); +#endif +#ifdef CONFIG_FEC_MXC setup_fec ();#endif
Signature · 1 line
1.8.4
PATCH v3 3/3 imx:mx6slevk implement power init board
Quoted 14 lines · Peng Fan
Implement
power_init_boardand related I2C interface configuration.After adding this, uboot can successfully detect and configure pmic.
"
U-Boot 2015.01-00281-ge29eddf (Feb 12 2015 - 09:24:01)CPU: Freescale i.MX6SL rev1.0 at 396 MHz Reset cause: POR Board: MX6SLEVK I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Quoted 4 lines
"
Signed-off-by Peng Fan <[email protected]>---
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
v3 cover imx: mx6slevk add pmic support
In reply to Peng FanHi Peng,
Quoted 22 lines · Peng Fan
This patch set is extracted from the previous "imx:mx6 add ldo bypass" patch set, with only one return value change.
patch 1/3 is add pad settings for I2C1
patch 2/3 is add I2C and PMIC support in board header file patch 3/3 is to add pmic support for mx6slevk.patch 3/3 is from patch 3/12 in previous "imx:mx6 add ldo bypass" patch, with only one small change is return value.
Changes v3:
Take Fabio's suggestion, for patch 3/3, remove ret variable, and directly "returnpfuze_mode_init(xxx)"Changes v2:
Changing "return-EIO" to "return ret".Peng Fan (3):
imx:mx6sl add I2c pad settings
imx:mx6slevk add pmic and i2c configuration
imx:mx6slevk implement power init board
Quoted 5 lines
arch/arm/include/asm/arch-mx6/mx6sl_pins.h | 5 ++++ board/freescale/mx6slevk/mx6slevk.c | 42 ++++++++++++++++++++++++++++++ include/configs/mx6slevk.h | 12 +++++++++ 3 files changed, 59 insertions(+)
They look good for me - if no comments will be posted, they will be merge by next iteration.
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================