Help needed: Enabling HPI causes some eMMC devices to stop working
Hi,
As part of the Linux Allwinner SoC support work I do in my spare time, I'm working on getting stock Linux running on the Utoo P66 Allwinner A13 based tablet.
This tablet is interesting because it uses an eMMC rather then raw nand as is typically seen on Allwinner tablets.
It has taken me a while to get the kernel to talk to the eMMC, in the end the following hack does the trick:
From: Hans de Goede <[email protected]>
Date: Wed, 18 Feb 2015 20:04:03 +0100
Subject: [PATCH] mmc: HACK: disable HPI
HACK: trying to enable HPI breaks EMMC access on the Utoo P66 tablet I'm trying to get supported, so disable it. FIXME: come up with a proper fix.
--- drivers/mmc/core/mmc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mmc/core/mmc.c +1 -1
@@ -1418,7 +1418,7 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,/* * Enable HPI feature (if supported) */ -if (card->ext_csd.hpi) { +if (0 && card->ext_csd.hpi) { err =mmc_switch (card,EXT_CSD_CMD_SET_NORMAL ,EXT_CSD_HPI_MGMT ,1 , card->ext_csd.generic_cmd6_time);
This patch has one good thing going for it, which it is that it makes the eMMC work, without this talking to the eMMC fails as soon as the kernel tries to read the partition table, with response-timeout errors when doing a mmc command 18 to read sector 0.
So this is as far as I've come, and beyond this my mmc knowledge is simply not good enough. Could this be a controller specific problem ? IOW do we need a controller flag to not enable HPi, like we've MMC_CAP2_BOOTPART_NOACC ? Or is this likely more something specific to the eMMC used.
Assuming for now it is something specific to the eMMC used, how do we fix this?
Is there maybe some way to figure out that enabling HPI is not a good idea on this eMMC?
Or do we need a quirk for this in devicetree? Now a days we can tie info to an sdio slave device in devicetree, so that is an option too.
Thanks & Regards,
Hans
Hi.
Quoted 39 lines · Hans de Goede
Hi,
As part of the Linux Allwinner SoC support work I do in my spare time, I'm working on getting stock Linux running on the Utoo P66 Allwinner A13 based tablet.
This tablet is interesting because it uses an eMMC rather then raw nand as is typically seen on Allwinner tablets.
It has taken me a while to get the kernel to talk to the eMMC, in the end the following hack does the trick:
From: Hans de Goede <[email protected]>
Date: Wed, 18 Feb 2015 20:04:03 +0100
Subject: [PATCH] mmc: HACK: disable HPIHACK: trying to enable HPI breaks EMMC access on the Utoo P66 tablet I'm trying to get supported, so disable it. FIXME: come up with a proper fix.
Signed-off-by Hans de Goede <[email protected]>--- drivers/mmc/core/mmc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/mmc/core/mmc.c +1
-1@@ -1418,7 +1418,7 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,/* * Enable HPI feature (if supported) */ -if (card->ext_csd.hpi) { +if (0 && card->ext_csd.hpi) { err =mmc_switch (card,EXT_CSD_CMD_SET_NORMAL ,EXT_CSD_HPI_MGMT ,1 , card->ext_csd.generic_cmd6_time);
Quoted 4 lines
This patch has one good thing going for it, which it is that it makes the eMMC work, without this talking to the eMMC fails as soon as the kernel tries to read the partition table, with response-timeout errors when doing a mmc command 18 to read sector 0.
I don't understand what response-timeout error related with HPI?
Quoted 11 lines
So this is as far as I've come, and beyond this my mmc knowledge is simply not good enough. Could this be a controller specific problem ? IOW do we need a controller flag to not enable HPi, like we've
MMC_CAP2_BOOTPART_NOACC? Or is this likely more something specific to the eMMC used.Assuming for now it is something specific to the eMMC used, how do we fix this?
Is there maybe some way to figure out that enabling HPI is not a good idea on this eMMC?
According to eMMC spec, HPI feature is mandatory. And it only needs to consider how the feature use. Do you use the BKOPS or other use-case?
Best Regards,
Jaehoon Chung
Quoted 12 lines
Or do we need a quirk for this in devicetree? Now a days we can tie info to an sdio slave device in devicetree, so that is an option too.
Thanks & Regards,
Hans
Signature · 3 lines
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi,
Quoted 42 lines · Jaehoon Chung
Hi.
Quoted 39 lines · Hans de Goede
Hi,
As part of the Linux Allwinner SoC support work I do in my spare time, I'm working on getting stock Linux running on the Utoo P66 Allwinner A13 based tablet.
This tablet is interesting because it uses an eMMC rather then raw nand as is typically seen on Allwinner tablets.
It has taken me a while to get the kernel to talk to the eMMC, in the end the following hack does the trick:
From: Hans de Goede <[email protected]>
Date: Wed, 18 Feb 2015 20:04:03 +0100
Subject: [PATCH] mmc: HACK: disable HPIHACK: trying to enable HPI breaks EMMC access on the Utoo P66 tablet I'm trying to get supported, so disable it. FIXME: come up with a proper fix.
Signed-off-by Hans de Goede <[email protected]>--- drivers/mmc/core/mmc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/mmc/core/mmc.c +1
-1@@ -1418,7 +1418,7 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,/* * Enable HPI feature (if supported) */ -if (card->ext_csd.hpi) { +if (0 && card->ext_csd.hpi) { err =mmc_switch (card,EXT_CSD_CMD_SET_NORMAL ,EXT_CSD_HPI_MGMT ,1 , card->ext_csd.generic_cmd6_time);
Quoted 6 lines
Quoted 4 lines
This patch has one good thing going for it, which it is that it makes the eMMC work, without this talking to the eMMC fails as soon as the kernel tries to read the partition table, with response-timeout errors when doing a mmc command 18 to read sector 0.
I don't understand what response-timeout error related with HPI?
If I do not apply the above patch / hack, which is in the early mmc init code, then after that any attempts to read something from the card results in a RTO error. It is not the actual use of HPI which breaks things, things break way earlier, as soon as the above piece of code executes.
Quoted 6 lines
Quoted 6 lines
So this is as far as I've come, and beyond this my mmc knowledge is simply not good enough. Could this be a controller specific problem ? IOW do we need a controller flag to not enable HPi, like we've
MMC_CAP2_BOOTPART_NOACC? Or is this likely more something specific to the eMMC used.
Quoted 7 lines
Quoted 4 lines
Assuming for now it is something specific to the eMMC used, how do we fix this?
Is there maybe some way to figure out that enabling HPI is not a good idea on this eMMC?
According to eMMC spec, HPI feature is mandatory. And it only needs to consider how the feature use. Do you use the BKOPS or other use-case?
HPI is not being used, if it were to be used it would be the non BKOPS case (e.g. interrupting an erase) as this card does not have BKOPS. This card does support erase, otherwise we could simply make the HPI enable code only run if the card supported either BKOPS and/or erase, but that will not help here.
We could delay enabling HPI until we do the first erase, but I'm not sure if that is going to be of much help, since eventually we do want to use trim on emmc -s by default and thus erase.
Regards,
Hans