ARM: at91: at91sam9x5: enable ISI and ov2640 support

index 17b8799..a7da0dd 100644
@@ -7,6 +7,7 @@
  */
 
 #include "at91sam9x5.dtsi"
+#include "at91sam9x5_isi.dtsi"
 #include "at91sam9x5_usart3.dtsi"
 #include "at91sam9x5_macb0.dtsi"
 

57 lines not on this page · raw message

index bd16bd3..b633b0f 100644
@@ -66,9 +66,47 @@
 					compatible = "wm8731";
 					reg = <0x1a>;
 				};
+
+				ov2640: camera at 0x30 {
+					compatible = "ovti,ov2640";
+					reg = <0x30>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+					resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
+					pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
+					clocks = <&pck0>;
+					clock-names = "xvclk";
+					assigned-clocks = <&pck0>;
+					assigned-clock-rates = <25000000>;
+					status = "disabled";
+
+					port {
+						ov2640_0: endpoint {
+							remote-endpoint = <&isi_0>;
+							bus-width = <8>;
+						};
+					};
+				};
 			};
 
 			pinctrl at fffff400 {
+				camera_sensor {
+					pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 {
+						atmel,pins =
+							<AT91_PIOC 15 AT91_PERIPH_C AT91_PINCTRL_NONE>;			/* PC15 periph C ISI_MCK */
+					};
+
+					pinctrl_sensor_reset: sensor_reset-0 {
+						atmel,pins =
+							<AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;		/* PA7 gpio */
+					};
+
+					pinctrl_sensor_power: sensor_power-0 {
+						atmel,pins =
+							<AT91_PIOA 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;		/* PA13 gpio */
+					};
+				};
+
 				mmc0 {
 					pinctrl_board_mmc0: mmc0-board {
 						atmel,pins =

@@ -122,6 +160,16 @@
 		usb1: ehci at 00700000 {
 			status = "okay";
 		};
+
+		isi: isi at f8048000 {
+			status = "disabled";
+			port {
+				isi_0: endpoint at 0 {
+					remote-endpoint = <&ov2640_0>;
+					bus-width = <8>;
+				};
+			};
+		};
 	};
 
 	sound {

index 1e4c49c..9808990 100644
@@ -16,10 +16,28 @@
 
 	ahb {
 		apb {
+			spi0: spi at f0000000 {
+				status = "disabled";
+			};
+
+			mmc1: mmc at f000c000 {
+				status = "disabled";
+			};
+
+			i2c0: i2c at f8010000 {
+				ov2640: camera at 0x30 {
+					status = "okay";
+				};
+			};
+
 			macb0: ethernet at f802c000 {
 				phy-mode = "rmii";
 				status = "okay";
 			};
 		};
+
+		isi: isi at f8048000 {
+			status = "okay";
+		};
 	};
 };

index a67375f..de4e1a5 100644
@@ -135,6 +135,12 @@ CONFIG_POWER_RESET=y
 CONFIG_WATCHDOG=y
 CONFIG_AT91SAM9X_WATCHDOG=y
 CONFIG_SSB=m
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_VIDEO_ATMEL_ISI=y
+CONFIG_SOC_CAMERA_OV2640=y
 CONFIG_FB=y
 CONFIG_FB_ATMEL=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y