mx6: Add initial SPL support for HummingBoard-i2eX

From: Fabio Estevam <[email protected]>

Add the initial SPL support for HummingBoard-i2eX, which is based on a MX6 Dual.

For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/

Based on the work from Jon Nettleton and Rabeeh Khoury.

Signed-off-by Fabio Estevam <[email protected]>

From: Fabio Estevam <[email protected]>

Add the initial SPL support for HummingBoard-i2eX, which is based on a MX6 Dual.

For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/

Based on the work from Jon Nettleton and Rabeeh Khoury.

Signed-off-by Fabio Estevam <[email protected]>

---
Currently only HummingBoard-i2eX is supported.

After this initial patch is accepted, then we can add the other Hummingboard and Cubox-i variants as well.

This mem_speed (1600) means that the MMDC imx6 code will calculate timings for 1600 MT/s, but in reality the memory clock will be 528 or 532 MHz. It would be better to override the speed to 1066 to make sure imx6 ddr code calculates proper timings.

To be honest, I don't understand why the code (arch/arm/cpu/armv7 /mx6/ddr.c) supports 1333/1600 MT/s when it's obvious that it's outside chip specs.

And a couple of more notes:
- I see that you don't use the extlinux boot mechanism (from distro defaults). Do you see any advantages of not using it?

- Would be nice to have HDMI support :)

- git patch gives a warning about one empty line

Hi Nikolay,

Quoted 4 lines · Nikolay Dimitrov

This mem_speed (1600) means that the MMDC imx6 code will calculate timings for 1600 MT/s, but in reality the memory clock will be 528 or 532 MHz. It would be better to override the speed to 1066 to make sure imx6 ddr code calculates proper timings.

mem_speed should be retrieved from the DDR3 datasheet.

For clarification, take a look at: board/gateworks/gw_ventana/gw_ventana_spl.c

/* MT41K128M16JT-125 */

static struct mx6_ddr3_cfg mt41k128m16jt_125 = {
     .mem_speed = 1600,

Looking at the MT41K128M16JT-125 datasheet it says it has a cycle time of 1.25ns, which corresponds
to 800MHz. Since this is DDR (double rate) then you get 1600MHz.

Quoted 3 lines

To be honest, I don't understand why the code (arch/arm/cpu/armv7 /mx6/ddr.c) supports 1333/1600 MT/s when it's obvious that it's outside chip specs.

The chip is not out of spec. In this ddr.c file we have:

     /* MX6D/MX6Q: 1066 MHz memory clock, clkper = 1.894ns = 1894ps */
     if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) {
         clock = 528;
         tcwl = 4;
     }

Quoted 3 lines

And a couple of more notes:
- I see that you don't use the extlinux boot mechanism (from distro defaults). Do you see any advantages of not using it?

No, I don't. This could be added later.

Quoted 1 line

- Would be nice to have HDMI support :)

Yes, HDMI, USB, PCI, SATA etc. One step at time ;-)

Quoted 1 line

- git patch gives a warning about one empty line

Thanks, I noticed this on the README file and will fix it in v2.

Regards,

Fabio Estevam

imx6 supports up to 528 MHz DDR3 clock as per datasheet, which makes 1058 MT/s data rate. Unfortunately such comments (like above) in the code doesn't help to clarify the differences. Which is a nice way to say the comments are wrong :).

Here's what happens - chip specs say that the chip supports 1600 MT/s (800 MHz DDR3 clock). The imx6 ddr code looks up in the switch/case and calculates timings for 800 MHz, while in reality the imx6 MMDC officially supports up to 528 MHz. What should happen - mem_speed should be clamped to imx6 model-specific speed limit, so the MMDC code can calculate valid timings.

Hi Nikolay,

Quoted 5 lines · Nikolay Dimitrov

imx6 supports up to 528 MHz DDR3 clock as per datasheet, which makes 1058 MT/s data rate. Unfortunately such comments (like above) in the code doesn't help to clarify the differences. Which is a nice way to say the comments are wrong :).

Quoted 6 lines

Here's what happens - chip specs say that the chip supports 1600 MT/s (800 MHz DDR3 clock). The imx6 ddr code looks up in the switch/case and calculates timings for 800 MHz, while in reality the imx6 MMDC officially supports up to 528 MHz. What should happen - mem_speed should be clamped to imx6 model-specific speed limit, so the MMDC code can calculate valid timings.

Care to submit a patch with your proposal?

This should be independent of this hummingboard support patch.

Thanks,

Fabio Estevam

From: Fabio Estevam <[email protected]>

Add the initial SPL support for HummingBoard-i2eX, which is based on a MX6 Dual.

For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/

Based on the work from Jon Nettleton and Rabeeh Khoury.

Signed-off-by Fabio Estevam <[email protected]>

---
Currently only HummingBoard-i2eX is supported.

After this initial patch is accepted, then we can add the other Hummingboard and Cubox-i variants as well.

 arch/arm/Kconfig                     |   6 +
 board/solidrun/mx6cuboxi/Kconfig     |  15 ++
 board/solidrun/mx6cuboxi/MAINTAINERS |   6 +
 board/solidrun/mx6cuboxi/Makefile    |   9 +
 board/solidrun/mx6cuboxi/README      |  23 +++
 board/solidrun/mx6cuboxi/mx6cuboxi.c | 336 +++++++++++++++++++++++++++++++++++
 configs/mx6cuboxi_spl_defconfig      |   6 +
 include/configs/mx6cuboxi.h          | 257 +++++++++++++++++++++++++++
 8 files changed, 658 insertions(+)
 create mode 100644 board/solidrun/mx6cuboxi/Kconfig
 create mode 100644 board/solidrun/mx6cuboxi/MAINTAINERS
 create mode 100644 board/solidrun/mx6cuboxi/Makefile
 create mode 100644 board/solidrun/mx6cuboxi/README
 create mode 100644 board/solidrun/mx6cuboxi/mx6cuboxi.c
 create mode 100644 configs/mx6cuboxi_spl_defconfig
 create mode 100644 include/configs/mx6cuboxi.h

arch/arm/Kconfig +6 -0

index 7ed0e20..7c383cb 100644
@@ -523,6 +523,11 @@ config TARGET_MX6SABRESD
 	select CPU_V7
 	select SUPPORT_SPL
 
+config TARGET_MX6CUBOXI
+	bool "Support Solid-run mx6 boards"
+	select CPU_V7
+	select SUPPORT_SPL
+
 config TARGET_MX6SLEVK
 	bool "Support mx6slevk"
 	select CPU_V7

@@ -856,6 +861,7 @@ source "board/siemens/draco/Kconfig"
 source "board/siemens/pxm2/Kconfig"
 source "board/siemens/rut/Kconfig"
 source "board/silica/pengwyn/Kconfig"
+source "board/solidrun/mx6cuboxi/Kconfig"
 source "board/solidrun/hummingboard/Kconfig"
 source "board/spear/spear300/Kconfig"
 source "board/spear/spear310/Kconfig"

board/solidrun/mx6cuboxi/Kconfig new file +15 -0

new file mode 100644
index 0000000..31d88b2
@@ -0,0 +1,15 @@
+if TARGET_MX6CUBOXI
+
+config SYS_BOARD
+	default "mx6cuboxi"
+
+config SYS_VENDOR
+	default "solidrun"
+
+config SYS_SOC
+	default "mx6"
+
+config SYS_CONFIG_NAME
+	default "mx6cuboxi"
+
+endif

board/solidrun/mx6cuboxi/MAINTAINERS new file +6 -0

new file mode 100644
index 0000000..3d468ed
@@ -0,0 +1,6 @@
+MX6CUBOXI BOARD
+M:	Fabio Estevam <[email protected]>
+S:	Maintained
+F:	board/solidrun/mx6cuboxi/
+F:	include/configs/mx6cuboxi.h
+F:	configs/mx6cuboxi_spl_defconfig

board/solidrun/mx6cuboxi/Makefile new file +9 -0

new file mode 100644
index 0000000..df425ac
@@ -0,0 +1,9 @@
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <[email protected]>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := mx6cuboxi.o

board/solidrun/mx6cuboxi/README new file +23 -0

new file mode 100644
index 0000000..29bff2b
@@ -0,0 +1,23 @@
+How to use U-boot on Solid-run mx6 hummingboard
+-----------------------------------------------
+
+- Build U-boot for hummingboard:
+
+$ make mrproper
+$ make mx6cuboxi_spl_defconfig
+$ make
+
+This will generate the SPL image called SPL and the u-boot.img.
+
+- Flash the SPL image into the SD card:
+
+sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+
+- Flash the u-boot.img image into the SD card:
+
+sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Insert the SD card in the hummingboard, power it up and U-boot messages
+should come up.
+
+

board/solidrun/mx6cuboxi/mx6cuboxi.c new file +336 -0

new file mode 100644
index 0000000..4cbd832
@@ -0,0 +1,336 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <[email protected]>
+ * Copyright (C) 2013 Jon Nettleton <[email protected]>
+ *
+ * Based on SPL code from Solidrun tree, which is:
+ * Author: Tungyi Lin <[email protected]>
+ *
+ * Derived from EDM_CF_IMX6 code by TechNexion,Inc
+ * Ported to SolidRun microSOM by Rabeeh Khoury <[email protected]>
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mx6-ddr.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_PD  (PAD_CTL_PUS_100K_DOWN |		\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_CLK  ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define ETH_PHY_RESET	IMX_GPIO_NR(4, 15)
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+struct fsl_esdhc_cfg usdhc_cfg[1] = {
+	{USDHC2_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return 1; /* uSDHC2 is always present */
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+	usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+	gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	/* AR8035 reset */
+	MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	/* AR8035 interrupt */
+	MX6_PAD_DI0_PIN2__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* GPIO16 -> AR8035 25MHz */
+	MX6_PAD_GPIO_16__ENET_REF_CLK	  | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC	  | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
+	MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+	gpio_direction_output(ETH_PHY_RESET, 0);
+	mdelay(2);
+	gpio_set_value(ETH_PHY_RESET, 1);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	int ret = enable_fec_anatop_clock(ENET_25MHZ);
+	if (ret)
+		return ret;
+
+	/* set gpr1[ENET_CLK_SEL] */
+	setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
+
+	setup_iomux_enet();
+
+	return cpu_eth_init(bis);
+}
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: MX6 Hummingboard\n");
+	return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+#include <spl.h>
+#include <libfdt.h>
+
+const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_sdclk_0 =  0x00020030,
+	.dram_sdclk_1 =  0x00020030,
+	.dram_cas =  0x00020030,
+	.dram_ras =  0x00020030,
+	.dram_reset =  0x00020030,
+	.dram_sdcke0 =  0x00003000,
+	.dram_sdcke1 =  0x00003000,
+	.dram_sdba2 =  0x00000000,
+	.dram_sdodt0 =  0x00003030,
+	.dram_sdodt1 =  0x00003030,
+	.dram_sdqs0 =  0x00000030,
+	.dram_sdqs1 =  0x00000030,
+	.dram_sdqs2 =  0x00000030,
+	.dram_sdqs3 =  0x00000030,
+	.dram_sdqs4 =  0x00000030,
+	.dram_sdqs5 =  0x00000030,
+	.dram_sdqs6 =  0x00000030,
+	.dram_sdqs7 =  0x00000030,
+	.dram_dqm0 =  0x00020030,
+	.dram_dqm1 =  0x00020030,
+	.dram_dqm2 =  0x00020030,
+	.dram_dqm3 =  0x00020030,
+	.dram_dqm4 =  0x00020030,
+	.dram_dqm5 =  0x00020030,
+	.dram_dqm6 =  0x00020030,
+	.dram_dqm7 =  0x00020030,
+};
+
+const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_ddr_type =  0x000C0000,
+	.grp_ddrmode_ctl =  0x00020000,
+	.grp_ddrpke =  0x00000000,
+	.grp_addds =  0x00000030,
+	.grp_ctlds =  0x00000030,
+	.grp_ddrmode =  0x00020000,
+	.grp_b0ds =  0x00000030,
+	.grp_b1ds =  0x00000030,
+	.grp_b2ds =  0x00000030,
+	.grp_b3ds =  0x00000030,
+	.grp_b4ds =  0x00000030,
+	.grp_b5ds =  0x00000030,
+	.grp_b6ds =  0x00000030,
+	.grp_b7ds =  0x00000030,
+};
+
+const struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x00000000,
+	.p0_mpwldectrl1 =  0x00000000,
+	.p1_mpwldectrl0 =  0x00000000,
+	.p1_mpwldectrl1 =  0x00000000,
+	.p0_mpdgctrl0 =    0x0314031c,
+	.p0_mpdgctrl1 =    0x023e0304,
+	.p1_mpdgctrl0 =    0x03240330,
+	.p1_mpdgctrl1 =    0x03180260,
+	.p0_mprddlctl =    0x3630323c,
+	.p1_mprddlctl =    0x3436283a,
+	.p0_mpwrdlctl =    0x36344038,
+	.p1_mpwrdlctl =    0x422a423c,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 1600,
+	.density = 4,
+	.width = 64,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00C03F3F, &ccm->CCGR0);
+	writel(0x0030FC03, &ccm->CCGR1);
+	writel(0x0FFFC000, &ccm->CCGR2);
+	writel(0x3FF00000, &ccm->CCGR3);
+	writel(0x00FFF300, &ccm->CCGR4);
+	writel(0x0F0000C3, &ccm->CCGR5);
+	writel(0x000003FF, &ccm->CCGR6);
+}
+
+static void gpr_init(void)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	/* enable AXI cache for VDOA/VPU/IPU */
+	writel(0xF00000CF, &iomux->gpr[4]);
+	/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+	writel(0x007F007F, &iomux->gpr[6]);
+	writel(0x007F007F, &iomux->gpr[7]);
+}
+
+/*
+ * This section requires the differentiation between Solidrun mx6 boards, but
+ * for now, it will configure only for the mx6dual hummingboard version.
+ */
+static void spl_dram_init(void)
+{
+	struct mx6_ddr_sysinfo sysinfo = {
+		/* width of data bus:0=16,1=32,2=64 */
+		.dsize = mem_ddr.width/32,
+		/* config for full 4GB range so that get_mem_size() works */
+		.cs_density = 32, /* 32Gb per CS */
+		/* single chip select */
+		.ncs = 1,
+		.cs1_mirror = 0,
+		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr = RZQ/4 */
+		.rtt_nom = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Nom = RZQ/4 */
+		.walat = 1,	/* Write additional latency */
+		.ralat = 5,	/* Read additional latency */
+		.mif3_mode = 3,	/* Command prediction working mode */
+		.bi_on = 1,	/* Bank interleaving enabled */
+		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	};
+
+	mx6dq_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+	gpr_init();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+
+void reset_cpu(ulong addr)
+{
+}
+#endif

configs/mx6cuboxi_spl_defconfig new file +6 -0

new file mode 100644
index 0000000..9847a9b
@@ -0,0 +1,6 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,SPL,MX6Q"
+CONFIG_ARM=y
+CONFIG_TARGET_MX6CUBOXI=y
+CONFIG_DM=y
+CONFIG_DM_THERMAL=y

include/configs/mx6cuboxi.h new file +247 -0

new file mode 100644
index 0000000..7ded5bc
@@ -0,0 +1,257 @@
+/*
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6Q SabreSD board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __MX6CUBOXI_CONFIG_H
+#define __MX6CUBOXI_CONFIG_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+#include "mx6_common.h"
+
+#define CONFIG_MX6
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_IMX6_THERMAL
+#define CONFIG_SYS_GENERIC_BOARD
+
+#define CONFIG_SYS_MALLOC_LEN		(2 * SZ_1M)
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+#define CONFIG_MXC_UART
+
+#define CONFIG_CMD_FUSE
+#if defined(CONFIG_CMD_FUSE) || defined(CONFIG_IMX6_THERMAL)
+#define CONFIG_MXC_OCOTP
+#endif
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/* Ethernet Configuration */
+#define CONFIG_FEC_MXC
+#ifdef CONFIG_FEC_MXC
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_FEC_MXC_PHYADDR		0
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+#endif
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_SETEXPR
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY		1
+
+#define CONFIG_LOADADDR			0x12000000
+#define CONFIG_SYS_TEXT_BASE		0x17800000
+
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+#define EMMC_ENV \
+	"emmcdev=2\0" \
+	"update_emmc_firmware=" \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"if ${get_cmd} ${update_sd_firmware_filename}; then " \
+			"if mmc dev ${emmcdev} 1; then "	\
+				"setexpr fw_sz ${filesize} / 0x200; " \
+				"setexpr fw_sz ${fw_sz} + 1; "	\
+				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
+			"fi; "	\
+		"fi\0"
+#else
+#define EMMC_ENV ""
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_addr=0x18000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"console=" CONFIG_CONSOLE_DEV "\0" \
+	"fdt_high=0xffffffff\0"	  \
+	"initrd_high=0xffffffff\0" \
+	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
+	"mmcpart=1\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"update_sd_firmware=" \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"if mmc dev ${mmcdev}; then "	\
+			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
+				"setexpr fw_sz ${filesize} / 0x200; " \
+				"setexpr fw_sz ${fw_sz} + 1; "	\
+				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
+			"fi; "	\
+		"fi\0" \
+	EMMC_ENV	  \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	"mmc dev ${mmcdev};" \
+	"if mmc rescan; then " \
+		"if run loadbootscript; then " \
+		"run bootscript; " \
+		"else " \
+			"if run loadimage; then " \
+				"run mmcboot; " \
+			"else run netboot; " \
+			"fi; " \
+		"fi; " \
+	"else run netboot; fi"
+
+#define CONFIG_ARP_TIMEOUT     200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE              256
+#define CONFIG_SYS_MAXARGS             16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START       0x10000000
+#define CONFIG_SYS_MEMTEST_END         0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE               (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS           1
+#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_SIZE			(8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+
+#if defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_ENV_OFFSET		(8 * 64 * 1024)
+#endif
+
+#define CONFIG_OF_LIBFDT
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+#ifdef CONFIG_SPL
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#include "imx6_spl.h"
+#endif
+
+#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_CONSOLE_DEV	"ttymxc0"
+#define CONFIG_MMCROOT		"/dev/mmcblk0p2"
+#define CONFIG_DEFAULT_FDT_FILE	"imx6q-hummingboard.dtb"

From: Fabio Estevam <[email protected]>

Add the initial SPL support for HummingBoard-i2eX, which is based on a MX6 Dual.

For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/

Based on the work from Jon Nettleton and Rabeeh Khoury.

Signed-off-by Fabio Estevam <[email protected]>

board/solidrun/mx6cuboxi/mx6cuboxi.c new file +13 -0

+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00C03F3F, &ccm->CCGR0);
+	writel(0x0030FC03, &ccm->CCGR1);
+	writel(0x0FFFC000, &ccm->CCGR2);
+	writel(0x3FF00000, &ccm->CCGR3);
+	writel(0x00FFF300, &ccm->CCGR4);
+	writel(0x0F0000C3, &ccm->CCGR5);
+	writel(0x000003FF, &ccm->CCGR6);
+}
+

+#define CONFIG_ARP_TIMEOUT 200UL

+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "

+#define CONFIG_STACKSIZE (128 * 1024)

+#define CONFIG_DEFAULT_FDT_FILE "imx6q-hummingboard.dtb"

+#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)

From: Fabio Estevam <[email protected]>

Add the initial SPL support for HummingBoard-i2eX, which is based on a MX6 Dual.

For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/

Based on the work from Jon Nettleton and Rabeeh Khoury.

Signed-off-by Fabio Estevam <[email protected]>

include/configs/mx6cuboxi.h new file +6 -0

+/* Command definition */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_SETEXPR
+#undef CONFIG_CMD_IMLS