PORT_LOGIC_SPEED_CHANGE set in PCIe designware driver
Hi All,
In pcie-designware.c, it sets the PORT_LOGIC_SPEED_CHANGE bit after linkup finished:
dw_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val); val |= PORT_LOGIC_SPEED_CHANGE; dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
As far as I know, it will try to use 5G/8G to communicate after setting this bit. When I used LSI SAS2208 PCIe-RAID card to test PCIe host driver, PCIe3.0 link was unstable and can not read/write PCIe-RAID BAR. When I moved above code before linkup, the process of enumeration was successful.
I wonder if anyone who also use the pcie-designware had met the same problem. Could we move the PORT_LOGIC_SPEED_CHANGE before linkup?
It will be very appreciate if anyone can offer some information.
Thanks,
Zhou
Hi All
Looking at par 3.13 of "Synopsis DesignWare Cores PCI Express Controller Databook" v4.20a (pag 159) I've found:
<<Speed Changing
When you set the default of the Directed Speed Change field of the Link Width and Speed Change Control register (GEN2_CTRL_OFF . DIRECT_SPEED_CHANGE) using the DEFAULT_GEN2_SPEED_CHANGE configuration parameter to "1", then the speed change is initiated automatically after link up, and the core clears the contents of GEN2_CTRL_OFF . DIRECT_SPEED_CHANGE. If you want to prevent this automatic speed change, then write a lower speed value to the Target Link Speed field of the Link Control 2 register (LINK_CONTROL2_LINK_STATUS2_REG . PCIE_CAP_TARGET_LINK_SPEED) through the DBI before
link up.>>
So my interpretation would be that at init phase it would be correct to trigger the DIRECT_SPPED_CHANGE before the link is up; that is it seems correct to me to move that part of the code before link up.
Does anybody have any idea about this?
Many Thanks
Gab
Quoted 31 lines
-----Original Message-----
From: Wangzhou (B)
Sent: Tuesday, April 14, 2015 8:21 AM
To: [email protected]
Cc: zhangjukuo; Gabriele Paoloni; Liguozhu (Kenneth)
Subject: [Query]PORT_LOGIC_SPEED_CHANGEset in PCIe designware driverHi All,
In
pcie-designware.c, it sets thePORT_LOGIC_SPEED_CHANGEbit after linkup
finished:
dw_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val); val |=PORT_LOGIC_SPEED_CHANGE;dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);As far as I know, it will try to use 5G/8G to communicate after setting this bit. When I used LSI SAS2208 PCIe-RAID card to test PCIe host driver, PCIe3.0 link was unstable and can not read/write PCIe-RAID BAR. When I moved above code before linkup, the process of enumeration was successful.
I wonder if anyone who also use the pcie-designware had met the same problem.
Could we move thePORT_LOGIC_SPEED_CHANGEbefore linkup?It will be very appreciate if anyone can offer some information.
Thanks,
Zhou
Quoted 15 lines · Gabriele Paoloni
Hi All
Looking at par 3.13 of "Synopsis DesignWare Cores PCI Express Controller Databook" v4.20a (pag 159) I've found:
<<Speed Changing
When you set the default of the Directed Speed Change field of the Link Width and Speed Change Control register (
GEN2_CTRL_OFF.DIRECT_SPEED_CHANGE) using theDEFAULT_GEN2_SPEED_CHANGEconfiguration parameter to "1", then the speed change is initiated automatically after link up, and the core clears the contents ofGEN2_CTRL_OFF.DIRECT_SPEED_CHANGE. If you want to prevent this automatic speed change, then write a lower speed value to the Target Link Speed field of the Link Control 2 register (LINK_CONTROL2_LINK_STATUS2_REG.PCIE_CAP_TARGET_LINK_SPEED) through the DBI before
link up.>>
Quoted 8 lines
So my interpretation would be that at init phase it would be correct to trigger the
DIRECT_SPPED_CHANGEbefore the link is up; that is it seems correct to me to move that part of the code before link up.Does anybody have any idea about this?
Many Thanks
Gab
Hi Gab,
Thanks for your reply. I will send a formal patch based on v4.1-rc1.
Regards,
Zhou
Quoted 36 lines
Quoted 24 lines
-----Original Message-----
From: Wangzhou (B)
Sent: Tuesday, April 14, 2015 8:21 AM
To: [email protected]
Cc: zhangjukuo; Gabriele Paoloni; Liguozhu (Kenneth)
Subject: [Query]PORT_LOGIC_SPEED_CHANGEset in PCIe designware driverHi All,
In
pcie-designware.c, it sets thePORT_LOGIC_SPEED_CHANGEbit after linkup
finished:
dw_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val); val |=PORT_LOGIC_SPEED_CHANGE;dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);As far as I know, it will try to use 5G/8G to communicate after setting this bit. When I used LSI SAS2208 PCIe-RAID card to test PCIe host driver, PCIe3.0 link was unstable and can not read/write PCIe-RAID BAR. When I moved above code before linkup, the process of enumeration was successful.
Quoted 8 lines
I wonder if anyone who also use the pcie-designware had met the same problem.
Could we move thePORT_LOGIC_SPEED_CHANGEbefore linkup?It will be very appreciate if anyone can offer some information.
Thanks,
Zhou.