Skip to contentSkip to conversation

New QorIQ p1020 based board support from Arcturus Networks Inc.

PATCH New Oleksandr G Zhadan 2 participants 2 messages Apr 15, 2015 – Apr 28, 2015 PowerPC

lore
Share & tools
lore

Oleksandr G Zhadan

author
#0 lore raw

PATCH 1/1 New QorIQ p1020 based board support from Arcturus Networks Inc.

New QorIQ p1020 based board support from Arcturus Networks Inc.
http://www.arcturusnetworks.com/products/ucp1020/

Signed-off-by Michael Durrant <[email protected]>
Signed-off-by Oleksandr G Zhadan <[email protected]>

---

 arch/powerpc/cpu/mpc85xx/Kconfig     |    4 +
 board/Arcturus/ucp1020/Kconfig       |   44 ++
 board/Arcturus/ucp1020/MAINTAINERS   |    7 +
 board/Arcturus/ucp1020/Makefile      |   33 ++
 board/Arcturus/ucp1020/README        |   54 ++
 board/Arcturus/ucp1020/cmd_arc.c     |  215 +++++++
 board/Arcturus/ucp1020/ddr.c         |  161 ++++++
 board/Arcturus/ucp1020/law.c         |   25 +
 board/Arcturus/ucp1020/spl.c         |  126 ++++
 board/Arcturus/ucp1020/spl_minimal.c |   67 +++
 board/Arcturus/ucp1020/tlb.c         |  101 ++++
 board/Arcturus/ucp1020/ucp1020.c     |  383 ++++++++++++
 configs/UCP1020_SPIFLASH_defconfig   |    6 +
 configs/UCP1020_defconfig            |    5 +
 include/configs/UCP1020.h            | 1058 ++++++++++++++++++++++++++++++++++
 15 files changed, 2289 insertions(+)
 create mode 100644 board/Arcturus/ucp1020/Kconfig
 create mode 100644 board/Arcturus/ucp1020/MAINTAINERS
 create mode 100644 board/Arcturus/ucp1020/Makefile
 create mode 100644 board/Arcturus/ucp1020/README
 create mode 100644 board/Arcturus/ucp1020/cmd_arc.c
 create mode 100644 board/Arcturus/ucp1020/ddr.c
 create mode 100644 board/Arcturus/ucp1020/law.c
 create mode 100644 board/Arcturus/ucp1020/spl.c
 create mode 100644 board/Arcturus/ucp1020/spl_minimal.c
 create mode 100644 board/Arcturus/ucp1020/tlb.c
 create mode 100644 board/Arcturus/ucp1020/ucp1020.c
 create mode 100644 configs/UCP1020_SPIFLASH_defconfig
 create mode 100644 configs/UCP1020_defconfig
 create mode 100644 include/configs/UCP1020.h
arch/powerpc/cpu/mpc85xx/Kconfig +4 -0
index adb5bd3..e481ab4 100644
@@ -153,6 +153,9 @@ config TARGET_XPEDITE537X
 config TARGET_XPEDITE550X
 	bool "Support xpedite550x"
 
+config TARGET_UCP1020
+	bool "Support uCP1020"
+
 endchoice
 
 source "board/freescale/b4860qds/Kconfig"

@@ -194,5 +197,6 @@ source "board/stx/stxssa/Kconfig"
 source "board/xes/xpedite520x/Kconfig"
 source "board/xes/xpedite537x/Kconfig"
 source "board/xes/xpedite550x/Kconfig"
+source "board/Arcturus/ucp1020/Kconfig"
 
 endmenu
board/Arcturus/ucp1020/Kconfig new file +44 -0

44 lines not on this page · raw message

board/Arcturus/ucp1020/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000..e4a4718
@@ -0,0 +1,7 @@
+UCP1020 BOARD
+M:	Oleksandr Zhadan and Michael Durrant <[email protected]>
+S:	Maintained
+F:	board/Arcturus/ucp1020/
+F:	include/configs/UCP1020.h
+F:	configs/UCP1020_defconfig
+F:	configs/UCP1020_SPIFLASH_defconfig
board/Arcturus/ucp1020/Makefile new file +33 -0
new file mode 100644
index 0000000..35c88b9
@@ -0,0 +1,33 @@
+#
+# Copyright 2013-2015 Arcturus Networks, Inc.
+# based on board/freescale/p1_p2_rdb_pc/Makefile
+# original copyright follows:
+# Copyright 2010-2011 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+
+obj-y	+= spl_minimal.o tlb.o law.o
+
+else
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
+
+obj-y        += ucp1020.o
+obj-y        += ddr.o
+obj-y        += law.o
+obj-y        += tlb.o
+obj-y        += cmd_arc.o
+
+endif
board/Arcturus/ucp1020/README new file +54 -0

54 lines not on this page · raw message

board/Arcturus/ucp1020/cmd_arc.c new file +215 -0

215 lines not on this page · raw message

board/Arcturus/ucp1020/ddr.c new file +161 -0

161 lines not on this page · raw message

board/Arcturus/ucp1020/law.c new file +25 -0
new file mode 100644
index 0000000..7d40905
@@ -0,0 +1,25 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc.
+ *           http://www.arcturusnetworks.com/products/ucp1020/
+ * based on board/freescale/p1_p2_rdb_pc/spl.c
+ * original copyright follows:
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifdef CONFIG_VSC7385_ENET
+	SET_LAW(CONFIG_SYS_VSC7385_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+#endif
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
board/Arcturus/ucp1020/spl.c new file +126 -0

126 lines not on this page · raw message

board/Arcturus/ucp1020/spl_minimal.c new file +67 -0

67 lines not on this page · raw message

board/Arcturus/ucp1020/tlb.c new file +101 -0

101 lines not on this page · raw message

board/Arcturus/ucp1020/ucp1020.c new file +383 -0

383 lines not on this page · raw message

configs/UCP1020_SPIFLASH_defconfig new file +6 -0
new file mode 100644
index 0000000..2ffb8da
@@ -0,0 +1,6 @@
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_UCP1020=y
+CONFIG_TARGET_UCP1020_SPIFLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_UCP1020=y
configs/UCP1020_defconfig new file +5 -0
new file mode 100644
index 0000000..61de360
@@ -0,0 +1,5 @@
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_UCP1020=y
+CONFIG_SPI_FLASH=y
+CONFIG_UCP1020=y
include/configs/UCP1020.h new file +1058 -0

1,058 lines not on this page · raw message

Signature · 1 line
2.1.4
#1 lore raw

PATCH 1/1 New QorIQ p1020 based board support from Arcturus Networks Inc.

Oleks,

I suggest to change the subject to "powerpc/mpc85xx: Add board support for ucp1020".

Quoted 6 lines · Oleksandr G Zhadan

New QorIQ p1020 based board support from Arcturus Networks Inc.
http://www.arcturusnetworks.com/products/ucp1020/

Signed-off-by Michael Durrant <[email protected]>
Signed-off-by Oleksandr G Zhadan <[email protected]>

---

<snip>

Quoted 5 lines
board/Arcturus/ucp1020/cmd_arc.c new file +5 -0
+int get_arc_info(void)
+{
+	int location = 1;
+
+	flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,

board/Arcturus/ucp1020/cmd_arc.c line 118

Quoted 10 lines
board/Arcturus/ucp1020/cmd_arc.c new file +10 -0
+				CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
+
+	if (spi_flash_read(flash, (0x200 - sizeof(smac)), sizeof(smac), smac)) {
+		location++;
+		if (spi_flash_read(flash, (0x400 - sizeof(smac)), sizeof(smac), smac)) {
+			location++;
+			if (spi_flash_read(flash, (CONFIG_ENV_SECT_SIZE + 0x200 - sizeof(smac)), sizeof(smac), smac)) {
+				location++;
+				if (spi_flash_read(flash, (CONFIG_ENV_SECT_SIZE + 0x400 - sizeof(smac)), sizeof(smac), smac)) {
+					printf("%s: ERROR: Failed to read all %d factory info spi locations\n", __func__, location);

These lines are way too long. Please wrap them back at or before 80 characters. You can keep printf string in one line, but the arguments should be in next.

There are many lines over 80 characters. Please try to fix all.

York