AM3517 usb host issue
I am trying to get the full-speed USB host working on an custom AM3517 device with the 3.18.12 kernel. The hardware works (a 2.6.37 kernel has been used for testing).
Does anyone have any experience of 3.18 (or similarly recent kernel on an AM3517 system) or have any pointers as where to start debugging? The ti-linux-3.14.y does not have any patches that aren't applied to the usb on 3.18.13.
The cpu port 1 is connected by a TI TUSB1106 usb transceiver that is directly connected to a full-speed hub (TI USB2046) hub so the OHCI driver is the only one in use.
Note, the ohci-omap3 is loaded as a module as this is how their user application expects to be able to shut down usb when it does not need it.
The device tree configuration for the usb host:
Quoted 6 lines
&usbhshost {
status = "okay"; /* just in case it is started disabled */
port1-mode = "ohci-phy-6pin-dpdm";
};Quoted 7 lines
&usbhsohci { status = "okay"; };&usbhsehci {
status = "disabled"; /* no ehci on board */
};
The usb from the logs is as follows. Some extra debugging has been added to verify the device-tree settings:
Quoted 36 lines
[ 0.000000] AM3517 ES1.1 (l2cache sgx neon)[ 0.869706] usbcore: registered new interface driver usbfs [ 0.874270] usbcore: registered new interface driver hub [ 0.878592] usbcore: registered new device driver usb [ 1.223199] usbhs_tll 48062000.usbhstll: starting TI HSUSB TLL Controller [ 1.273000] usbhs_omap 48064000.usbhshost: ports 0 [ 1.278291] usbhs_omap 48064000.usbhshost: port 0: ohci-phy-6pin-dpdm [ 1.284476] usbhs_omap 48064000.usbhshost: port0-mode: ohci-phy-6pin-dpdm ->5 [ 1.288689] usbhs_tll 48062000.usbhstll: omap_tll_init() [ 1.293628] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 1.298434] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 1.302730] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 1.307668] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.310142] stopping usb controller [ 1.419910] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.423547] usbhs_omap 48064000.usbhshost: 3 ports [ 1.429065] usbhs_omap 48064000.usbhshost: starting TI HSUSB Controller [ 1.433831] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 1.438625] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 1.442921] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 1.448548] usbhs_omap 48064000.usbhshost: omap_usbhs_rev1_hostconfig => [ 1.455034] usbhs_omap 48064000.usbhshost: UHH setup done, uhh_hostconfig=80d [ 1.459918] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.462337] stopping usb controller [ 1.569905] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.575408] usbhs_omap 48064000.usbhshost: populating usb sub nodes....[ 77.609168] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 77.613927] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 77.618374] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 77.802694] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 77.816003] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1 [ 77.827391] usb usb1: Product: OHCI Host Controller [ 77.838674] usb usb1: Manufacturer: Linux 3.18.13-00203-ga3c52be-dirty ohci_d [ 77.849913] usb usb1: SerialNumber: 48064400.ohci
Signature · 6 lines
Ben Dooks http://www.codethink.co.uk/ Senior Engineer Codethink - Providing Genius -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi,
Quoted 13 lines · Ben Dooks
I am trying to get the full-speed USB host working on an custom AM3517 device with the 3.18.12 kernel. The hardware works (a 2.6.37 kernel has been used for testing).
Does anyone have any experience of 3.18 (or similarly recent kernel on an AM3517 system) or have any pointers as where to start debugging? The ti-linux-3.14.y does not have any patches that aren't applied to the usb on 3.18.13.
The cpu port 1 is connected by a TI TUSB1106 usb transceiver that is directly connected to a full-speed hub (TI USB2046) hub so the OHCI driver is the only one in use.
Quoted 5 lines
Note, the ohci-omap3 is loaded as a module as this is how their user application expects to be able to shut down usb when it does not need it.
The device tree configuration for the usb host:
and what exactly doesn't work ? That old OHCI driver hasn't been touched in years, it's no surprise that it stopped working :-(
Anyway, what exactly doesn't work ? No device enumerates ? Do you get any IRQs by plugging a new device in ?
Quoted 10 lines
Quoted 10 lines
&usbhshost { status = "okay"; /* just in case it is started disabled */ port1-mode = "ohci-phy-6pin-dpdm"; };&usbhsohci { status = "okay"; };
Quoted 44 lines
Quoted 3 lines
&usbhsehci {
status = "disabled"; /* no ehci on board */
};The usb from the logs is as follows. Some extra debugging has been added to verify the device-tree settings:
Quoted 36 lines
[ 0.000000] AM3517 ES1.1 (l2cache sgx neon)[ 0.869706] usbcore: registered new interface driver usbfs [ 0.874270] usbcore: registered new interface driver hub [ 0.878592] usbcore: registered new device driver usb [ 1.223199] usbhs_tll 48062000.usbhstll: starting TI HSUSB TLL Controller [ 1.273000] usbhs_omap 48064000.usbhshost: ports 0 [ 1.278291] usbhs_omap 48064000.usbhshost: port 0: ohci-phy-6pin-dpdm [ 1.284476] usbhs_omap 48064000.usbhshost: port0-mode: ohci-phy-6pin-dpdm ->5 [ 1.288689] usbhs_tll 48062000.usbhstll: omap_tll_init() [ 1.293628] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 1.298434] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 1.302730] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 1.307668] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.310142] stopping usb controller [ 1.419910] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.423547] usbhs_omap 48064000.usbhshost: 3 ports [ 1.429065] usbhs_omap 48064000.usbhshost: starting TI HSUSB Controller [ 1.433831] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 1.438625] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 1.442921] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 1.448548] usbhs_omap 48064000.usbhshost: omap_usbhs_rev1_hostconfig => [ 1.455034] usbhs_omap 48064000.usbhshost: UHH setup done, uhh_hostconfig=80d [ 1.459918] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.462337] stopping usb controller [ 1.569905] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.575408] usbhs_omap 48064000.usbhshost: populating usb sub nodes....[ 77.609168] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 77.613927] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 77.618374] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 77.802694] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 77.816003] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1 [ 77.827391] usb usb1: Product: OHCI Host Controller [ 77.838674] usb usb1: Manufacturer: Linux 3.18.13-00203-ga3c52be-dirty ohci_d [ 77.849913] usb usb1: SerialNumber: 48064400.ohci
OK, so this is roothub, what happens when a device is plugged to the other end ? Is VBUS charged ? We didn't even enumerate TUSB2046, did you look at its datasheet (http://www.ti.com/lit/ds/symlink/tusb2046b.pdf) ? What is the state of RESETn pin ? Perhaps that's tied to a GPIO and the old TI kernel toggles that ? Anything interesting from usbmon ?
cheers
Signature · 1 line
balbi
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA256
Quoted 20 lines · Felipe Balbi
Hi,
Quoted 17 lines · Ben Dooks
I am trying to get the full-speed USB host working on an custom AM3517 device with the 3.18.12 kernel. The hardware works (a 2.6.37 kernel has been used for testing).
Does anyone have any experience of 3.18 (or similarly recent kernel on an AM3517 system) or have any pointers as where to start debugging? The ti-linux-3.14.y does not have any patches that aren't applied to the usb on 3.18.13.
The cpu port 1 is connected by a TI TUSB1106 usb transceiver that is directly connected to a full-speed hub (TI USB2046) hub so the OHCI driver is the only one in use.
Note, the ohci-omap3 is loaded as a module as this is how their user application expects to be able to shut down usb when it does not need it.
Quoted 7 lines
Quoted 1 line
The device tree configuration for the usb host:
and what exactly doesn't work ? That old OHCI driver hasn't been touched in years, it's no surprise that it stopped working :-(
Anyway, what exactly doesn't work ? No device enumerates ? Do you get any IRQs by plugging a new device in ?
I will check the interrupts when I get back into the office.
There is only one device (the hub) which isn't enumerating and is hard-wired on the board.
Quoted 59 lines
Quoted 5 lines
Quoted 5 lines
&usbhshost { status = "okay"; /* just in case it is started
disabled */port1-mode = "ohci-phy-6pin-dpdm"; };
Quoted 53 lines
Quoted 3 lines
&usbhsohci { status = "okay"; };
&usbhsehci { status = "disabled"; /* no ehci on board */ };
The usb from the logs is as follows. Some extra debugging has been added to verify the device-tree settings:
Quoted 45 lines
[ 0.000000] AM3517 ES1.1 (l2cache sgx neon)[ 0.869706] usbcore: registered new interface driver usbfs [ 0.874270] usbcore: registered new interface driver hub [ 0.878592] usbcore: registered new device driver usb [ 1.223199] usbhs_tll 48062000.usbhstll: starting TI HSUSBTLL Controller [ 1.273000]
usbhs_omap48064000.usbhshost:
ports 0 [ 1.278291]usbhs_omap48064000.usbhshost: port 0:
ohci-phy-6pin-dpdm [ 1.284476]usbhs_omap
48064000.usbhshost: port0-mode: ohci-phy-6pin-dpdm ->5 [ 1.288689]usbhs_tll48062000.usbhstll:omap_tll_init()[ 1.293628] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 1.298434] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 1.302730] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 1.307668] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.310142] stopping usb controller [ 1.419910] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.423547] usbhs_omap 48064000.usbhshost: 3 ports [ 1.429065] usbhs_omap 48064000.usbhshost: starting TIHSUSB Controller [ 1.433831]
usbhs_omap48064000.usbhshost:usbhs_runtime_resume[ 1.438625]usbhs_omap
48064000.usbhshost: sysconfig0x00001009[ 1.442921]usbhs_tll48062000.usbhstll:omap_tll_enable()[ 1.448548] usbhs_omap 48064000.usbhshost: omap_usbhs_rev1_hostconfig => [ 1.455034] usbhs_omap 48064000.usbhshost: UHH setup done, uhh_hostconfig=80d [ 1.459918] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.462337] stopping usb controller [ 1.569905] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.575408] usbhs_omap 48064000.usbhshost: populating usbsub nodes....
[ 77.609168] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 77.613927] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 77.618374] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 77.802694] usb usb1: New USB device found, idVendor=1d6b,idProduct=0001 [ 77.816003] usb usb1: New USB device strings:
Mfr=3, Product=2, SerialNumber1 [ 77.827391] usb usb1:
Product: OHCI Host Controller [ 77.838674] usb usb1:
Manufacturer: Linux 3.18.13-00203-ga3c52be-dirtyohci_d[ 77.849913] usb usb1: SerialNumber: 48064400.ohci
Quoted 6 lines
OK, so this is roothub, what happens when a device is plugged to the other end ? Is VBUS charged ? We didn't even enumerate TUSB2046, did you look at its datasheet
(http://www.ti.com/lit/ds/symlink/tusb2046b.pdf) ? What is the state of RESETn pin ? Perhaps that's tied to a GPIO and the old TI kernel toggles that ? Anything interesting from usbmon ?
I've gone through the schematics and verified the hub's reset line is connected where we think it is (will try and check with a 'scope on monday that it is being taken high, the boot-loader starts it low).
The root has just the one device connected, and unfortunately the hw designer decided to hard-wire the D+ pull-up to 3.3V instead of the transceiver's pull pin.
Not tried usbmon yet. However if the hub is not being detected then probably won't show anything either.
I am going to install devmem2 into the root image and use it to poke around and see the state of the system at run time.
Thanks for looking in to this.
- --
Ben Dooks http://www.codethink.co.uk/
Senior Engineer Codethink - Providing Genius
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAEBCAAGBQJVX43iAAoJEMuhVOkVU3uzaHUH/0rcRBoWJn07wuJZSDmX2cf7 pFV1jya+Qx1zJmVdwDfT1MLAW5XCdio5U+sZyWFe7mxbZd3IPXhMud4xAqjdEnvQ amS3WcLVqbqLCbIq8KYKN6eSZqnf8gO2sPhSo3j86TpWyaQHstiS+FQu4Rv1v1XD IUfXoQyp/taKihVcs7VvP6bT5lARr2lANGCJ6VAchHjLr04NM4VJUUXJ18m/Zxfm A0Y6dJeLuT4MF9QpOd7KYVn2gYpdwtznF87J8gqJcYJHhggY1LWYBKiJSzBT6m/0 JYJldljoCEznro7G0ZaPMubWQO363SVEqDf3b7lmYuBKPo+7z/dr/KVmwiBf2a0= =Hegi
-----END PGP SIGNATURE-----
Hi,
Quoted 29 lines · Ben Dooks
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA256Quoted 25 lines · Felipe Balbi
Hi,
Quoted 13 lines · Ben Dooks
I am trying to get the full-speed USB host working on an custom AM3517 device with the 3.18.12 kernel. The hardware works (a 2.6.37 kernel has been used for testing).
Does anyone have any experience of 3.18 (or similarly recent kernel on an AM3517 system) or have any pointers as where to start debugging? The ti-linux-3.14.y does not have any patches that aren't applied to the usb on 3.18.13.
The cpu port 1 is connected by a TI TUSB1106 usb transceiver that is directly connected to a full-speed hub (TI USB2046) hub so the OHCI driver is the only one in use.
Quoted 5 lines
Note, the ohci-omap3 is loaded as a module as this is how their user application expects to be able to shut down usb when it does not need it.
The device tree configuration for the usb host:
and what exactly doesn't work ? That old OHCI driver hasn't been touched in years, it's no surprise that it stopped working :-(
Quoted 7 lines
Quoted 2 lines
Anyway, what exactly doesn't work ? No device enumerates ? Do you get any IRQs by plugging a new device in ?
I will check the interrupts when I get back into the office.
There is only one device (the hub) which isn't enumerating and is hard-wired on the board.
alright, that makes things a little more difficult :-)
Quoted 74 lines
Quoted 59 lines
Quoted 5 lines
Quoted 5 lines
&usbhshost { status = "okay"; /* just in case it is started
disabled */port1-mode = "ohci-phy-6pin-dpdm"; };
Quoted 53 lines
Quoted 3 lines
&usbhsohci { status = "okay"; };
&usbhsehci { status = "disabled"; /* no ehci on board */ };
The usb from the logs is as follows. Some extra debugging has been added to verify the device-tree settings:
Quoted 45 lines
[ 0.000000] AM3517 ES1.1 (l2cache sgx neon)[ 0.869706] usbcore: registered new interface driver usbfs [ 0.874270] usbcore: registered new interface driver hub [ 0.878592] usbcore: registered new device driver usb [ 1.223199] usbhs_tll 48062000.usbhstll: starting TI HSUSBTLL Controller [ 1.273000]
usbhs_omap48064000.usbhshost:
ports 0 [ 1.278291]usbhs_omap48064000.usbhshost: port 0:
ohci-phy-6pin-dpdm [ 1.284476]usbhs_omap
48064000.usbhshost: port0-mode: ohci-phy-6pin-dpdm ->5 [ 1.288689]usbhs_tll48062000.usbhstll:omap_tll_init()[ 1.293628] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 1.298434] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 1.302730] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 1.307668] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.310142] stopping usb controller [ 1.419910] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.423547] usbhs_omap 48064000.usbhshost: 3 ports [ 1.429065] usbhs_omap 48064000.usbhshost: starting TIHSUSB Controller [ 1.433831]
usbhs_omap48064000.usbhshost:usbhs_runtime_resume[ 1.438625]usbhs_omap
48064000.usbhshost: sysconfig0x00001009[ 1.442921]usbhs_tll48062000.usbhstll:omap_tll_enable()[ 1.448548] usbhs_omap 48064000.usbhshost: omap_usbhs_rev1_hostconfig => [ 1.455034] usbhs_omap 48064000.usbhshost: UHH setup done, uhh_hostconfig=80d [ 1.459918] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.462337] stopping usb controller [ 1.569905] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.575408] usbhs_omap 48064000.usbhshost: populating usbsub nodes....
[ 77.609168] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 77.613927] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 77.618374] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 77.802694] usb usb1: New USB device found, idVendor=1d6b,idProduct=0001 [ 77.816003] usb usb1: New USB device strings:
Mfr=3, Product=2, SerialNumber1 [ 77.827391] usb usb1:
Product: OHCI Host Controller [ 77.838674] usb usb1:
Manufacturer: Linux 3.18.13-00203-ga3c52be-dirtyohci_d[ 77.849913] usb usb1: SerialNumber: 48064400.ohciQuoted 6 lines
OK, so this is roothub, what happens when a device is plugged to the other end ? Is VBUS charged ? We didn't even enumerate TUSB2046, did you look at its datasheet
(http://www.ti.com/lit/ds/symlink/tusb2046b.pdf) ? What is the state of RESETn pin ? Perhaps that's tied to a GPIO and the old TI kernel toggles that ? Anything interesting from usbmon ?I've gone through the schematics and verified the hub's reset line is connected where we think it is (will try and check with a 'scope on monday that it is being taken high, the boot-loader starts it low).
The root has just the one device connected, and unfortunately the hw designer decided to hard-wire the D+ pull-up to 3.3V instead of the transceiver's pull pin.
Quoted 7 lines
Not tried usbmon yet. However if the hub is not being detected then probably won't show anything either.
I am going to install devmem2 into the root image and use it to poke around and see the state of the system at run time.
Thanks for looking in to this.
yeah, no problem. You probably want to first make sure VBUS is alive behind the HUB (iow, make sure the hub is powered up as you'd expect), then make sure VBUS is coming out on the other end (the hub's ports). The make sure RESETn is high as you'd want it to be. After that, then I guess only register pick-and-poke is left.
cheers
Signature · 1 line
balbi
Quoted 108 lines · Ben Dooks
Quoted 20 lines · Felipe Balbi
Hi,
Quoted 17 lines · Ben Dooks
I am trying to get the full-speed USB host working on an custom AM3517 device with the 3.18.12 kernel. The hardware works (a 2.6.37 kernel has been used for testing).
Does anyone have any experience of 3.18 (or similarly recent kernel on an AM3517 system) or have any pointers as where to start debugging? The ti-linux-3.14.y does not have any patches that aren't applied to the usb on 3.18.13.
The cpu port 1 is connected by a TI TUSB1106 usb transceiver that is directly connected to a full-speed hub (TI USB2046) hub so the OHCI driver is the only one in use.
Note, the ohci-omap3 is loaded as a module as this is how their user application expects to be able to shut down usb when it does not need it.
Quoted 7 lines
Quoted 1 line
The device tree configuration for the usb host:
and what exactly doesn't work ? That old OHCI driver hasn't been touched in years, it's no surprise that it stopped working :-(
Anyway, what exactly doesn't work ? No device enumerates ? Do you get any IRQs by plugging a new device in ?
I will check the interrupts when I get back into the office.
There is only one device (the hub) which isn't enumerating and is hard-wired on the board.
Quoted 59 lines
Quoted 5 lines
Quoted 5 lines
&usbhshost { status = "okay"; /* just in case it is started
disabled */port1-mode = "ohci-phy-6pin-dpdm"; };
Quoted 53 lines
Quoted 3 lines
&usbhsohci { status = "okay"; };
&usbhsehci { status = "disabled"; /* no ehci on board */ };
The usb from the logs is as follows. Some extra debugging has been added to verify the device-tree settings:
Quoted 45 lines
[ 0.000000] AM3517 ES1.1 (l2cache sgx neon)[ 0.869706] usbcore: registered new interface driver usbfs [ 0.874270] usbcore: registered new interface driver hub [ 0.878592] usbcore: registered new device driver usb [ 1.223199] usbhs_tll 48062000.usbhstll: starting TI HSUSBTLL Controller [ 1.273000]
usbhs_omap48064000.usbhshost:
ports 0 [ 1.278291]usbhs_omap48064000.usbhshost: port 0:
ohci-phy-6pin-dpdm [ 1.284476]usbhs_omap
48064000.usbhshost: port0-mode: ohci-phy-6pin-dpdm ->5 [ 1.288689]usbhs_tll48062000.usbhstll:omap_tll_init()[ 1.293628] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 1.298434] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 1.302730] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 1.307668] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.310142] stopping usb controller [ 1.419910] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.423547] usbhs_omap 48064000.usbhshost: 3 ports [ 1.429065] usbhs_omap 48064000.usbhshost: starting TIHSUSB Controller [ 1.433831]
usbhs_omap48064000.usbhshost:usbhs_runtime_resume[ 1.438625]usbhs_omap
48064000.usbhshost: sysconfig0x00001009[ 1.442921]usbhs_tll48062000.usbhstll:omap_tll_enable()[ 1.448548] usbhs_omap 48064000.usbhshost: omap_usbhs_rev1_hostconfig => [ 1.455034] usbhs_omap 48064000.usbhshost: UHH setup done, uhh_hostconfig=80d [ 1.459918] usbhs_omap 48064000.usbhshost: usbhs_runtime_suspend [ 1.462337] stopping usb controller [ 1.569905] usbhs_tll 48062000.usbhstll: omap_tll_disable() [ 1.575408] usbhs_omap 48064000.usbhshost: populating usbsub nodes....
[ 77.609168] usbhs_omap 48064000.usbhshost: usbhs_runtime_resume [ 77.613927] usbhs_omap 48064000.usbhshost: sysconfig 0x00001009 [ 77.618374] usbhs_tll 48062000.usbhstll: omap_tll_enable() [ 77.802694] usb usb1: New USB device found, idVendor=1d6b,idProduct=0001 [ 77.816003] usb usb1: New USB device strings:
Mfr=3, Product=2, SerialNumber1 [ 77.827391] usb usb1:
Product: OHCI Host Controller [ 77.838674] usb usb1:
Manufacturer: Linux 3.18.13-00203-ga3c52be-dirtyohci_d[ 77.849913] usb usb1: SerialNumber: 48064400.ohciQuoted 6 lines
OK, so this is roothub, what happens when a device is plugged to the other end ? Is VBUS charged ? We didn't even enumerate TUSB2046, did you look at its datasheet
(http://www.ti.com/lit/ds/symlink/tusb2046b.pdf) ? What is the state of RESETn pin ? Perhaps that's tied to a GPIO and the old TI kernel toggles that ? Anything interesting from usbmon ?I've gone through the schematics and verified the hub's reset line is connected where we think it is (will try and check with a 'scope on monday that it is being taken high, the boot-loader starts it low).
The root has just the one device connected, and unfortunately the hw designer decided to hard-wire the D+ pull-up to 3.3V instead of the transceiver's pull pin.
Quoted 7 lines
Not tried usbmon yet. However if the hub is not being detected then probably won't show anything either.
I am going to install devmem2 into the root image and use it to poke around and see the state of the system at run time.
Thanks for looking in to this.
The hub is functioning, 3.3V is up, the ~RESET line is high and the 6MHz crystal is running at 6MHz.
I will get a register dump from both sets and compare.
Signature · 2 lines
Ben Dooks http://www.codethink.co.uk/ Senior Engineer Codethink - Providing Genius
A message that is not in the archive (sent off-list or not yet received): 20150522135039.GA5582-HgARHv6XitJaoMGHk7MhZQC/[email protected]
Quoted 20 lines · Felipe Balbi
Hi,
Quoted 17 lines · Ben Dooks
I am trying to get the full-speed USB host working on an custom AM3517 device with the 3.18.12 kernel. The hardware works (a 2.6.37 kernel has been used for testing).
Does anyone have any experience of 3.18 (or similarly recent kernel on an AM3517 system) or have any pointers as where to start debugging? The ti-linux-3.14.y does not have any patches that aren't applied to the usb on 3.18.13.
The cpu port 1 is connected by a TI TUSB1106 usb transceiver that is directly connected to a full-speed hub (TI USB2046) hub so the OHCI driver is the only one in use.
Note, the ohci-omap3 is loaded as a module as this is how their user application expects to be able to shut down usb when it does not need it.
Quoted 7 lines
Quoted 1 line
The device tree configuration for the usb host:
and what exactly doesn't work ? That old OHCI driver hasn't been touched in years, it's no surprise that it stopped working :-(
Anyway, what exactly doesn't work ? No device enumerates ? Do you get any IRQs by plugging a new device in ?
I just found this in my backlog, and thought I should follow up with the issue.
It turns out that even if we're not using the EHCI unit, the 120m functional clock needs to be enabled. This may be down to an internal routing of port signals, or the USB front-end needing it.
I've added a local boolean fix to enable the clock, and will post it as soon as we've had a chance to review and document.
Signature · 6 lines
Ben Dooks http://www.codethink.co.uk/ Senior Engineer Codethink - Providing Genius -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html