Don't export VERBOSE unless V=1 (for CMake)
PATCH 1/1 Don't export VERBOSE unless V=1 (for CMake)
CMake verbose mode is based on VERBOSE environment variable.
* If VERBOSE is exported but empty, only "Dependee ... is newer than depender ..." messages are shown.
* If VERBOSE is exported and set (whatever the value), all compilation commands are shown.
VERBOSE is currently systematically exported by Buildroot, even if it is empty, in the root Makefile, which implies that the "light" verbose mode - with "Dependee ... is newer than depender ..." messages - is always enabled.
VERBOSE should only be exported when V=1, which is the standard way to enable verbose mode in Buildroot.
--- Makefile | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
Makefile +2 -1
@@ -215,6 +215,7 @@ ifeq ($(KBUILD_VERBOSE),1) ifndef VERBOSE VERBOSE = 1 endif +export VERBOSE else quiet = quiet_ Q = @
@@ -228,7 +229,7 @@ SHELL := $(shell if [ -x "$$BASH" ]; then echo $$BASH; \ # kconfig uses CONFIG_SHELL CONFIG_SHELL := $(SHELL) -export SHELL CONFIG_SHELL quiet Q KBUILD_VERBOSE VERBOSE +export SHELL CONFIG_SHELL quiet Q KBUILD_VERBOSE ifndef HOSTAR HOSTAR := ar
Signature · 1 line
2.1.4
PATCH 1/1 Don't export VERBOSE unless V=1 (for CMake)
Quoted 11 lines · C?dric Marie
CMake verbose mode is based on VERBOSE environment variable.
* If VERBOSE is exported but empty, only "Dependee ... is newer than depender ..." messages are shown.
* If VERBOSE is exported and set (whatever the value), all compilation commands are shown.VERBOSE is currently systematically exported by Buildroot, even if it is empty, in the root
Makefile, which implies that the "light" verbose mode - with "Dependee ... is newer than depender ..." messages - is always enabled.
Quoted 4 lines
VERBOSE should only be exported when V=1, which is the standard way to enable verbose mode in Buildroot.
Signed-off-by C?dric Marie <[email protected]>
Regards,
Arnout
Quoted 26 lines
--- Makefile | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)Makefile +2
-1@@ -215,6 +215,7 @@ ifeq ($(KBUILD_VERBOSE),1) ifndef VERBOSE VERBOSE = 1 endif +export VERBOSE else quiet = quiet_ Q = @@@ -228,7 +229,7 @@ SHELL := $(shell if [ -x "$$BASH" ]; then echo $$BASH; \ # kconfig uses CONFIG_SHELL CONFIG_SHELL := $(SHELL) -export SHELL CONFIG_SHELL quiet Q KBUILD_VERBOSE VERBOSE +export SHELL CONFIG_SHELL quiet Q KBUILD_VERBOSE ifndef HOSTAR HOSTAR := ar
Signature · 6 lines
Arnout Vandecappelle arnout at mind be Senior Embedded Software Architect +32-16-286500 Essensium/Mind http://www.mind.be G.Geenslaan 9, 3001 Leuven, Belgium BE 872 984 063 RPR Leuven LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle GPG fingerprint: 7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F
PATCH 1/1 Don't export VERBOSE unless V=1 (for CMake)
In reply to Cédric MarieQuoted 13 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"C?dric" == C?dric Marie <[email protected]> writes:
CMake verbose mode is based on VERBOSE environment variable.
* If VERBOSE is exported but empty, only "Dependee ... is newer than depender ..." messages are shown.
* If VERBOSE is exported and set (whatever the value), all compilation commands are shown.VERBOSE is currently systematically exported by Buildroot, even if it is empty, in the root
Makefile, which implies that the "light" verbose mode - with "Dependee ... is newer than depender ..." messages - is always enabled.
Quoted 4 lines
VERBOSE should only be exported when V=1, which is the standard way to enable verbose mode in Buildroot.
Signed-off-by C?dric Marie <[email protected]>
Committed, thanks.
Signature · 1 line
Bye, Peter Korsgaard