Skip to contentSkip to conversation

sunxi: Enable USB DRC on Wexler TAB7200

PATCH New Aleksei Mamlin 2 participants 2 messages Jul 30, 2015 – Jul 31, 2015

lore
Share & tools
lore

Aleksei Mamlin

author
#0 lore raw

PATCH 1/1 sunxi: Enable USB DRC on Wexler TAB7200

Enable the otg/drc usb controller on the Wexler TAB7200 tablet.

Signed-off-by Aleksei Mamlin <[email protected]>
---
 configs/Wexler_TAB7200_defconfig | 5 +++++
 1 file changed, 5 insertions(+)
configs/Wexler_TAB7200_defconfig +5 -0
index eadceb2..55e1b6b 100644
@@ -2,10 +2,15 @@ CONFIG_ARM=y
 CONFIG_ARCH_SUNXI=y
 CONFIG_MACH_SUN7I=y
 CONFIG_DRAM_CLK=384
+CONFIG_USB0_VBUS_PIN="PB9"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH4"
+CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:24,pclk_khz:33000,le:45,ri:210,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_POWER="PH8"
 CONFIG_VIDEO_LCD_BL_EN="PH7"
 CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_USB_MUSB_SUNXI=y
 CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-wexler-tab7200"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_SPL=y
Signature · 1 line
2.3.6
#1 lore raw

PATCH 1/1 sunxi: Enable USB DRC on Wexler TAB7200

Hi Aleksei,

Quoted 3 lines · Aleksei Mamlin

Enable the otg/drc usb controller on the Wexler TAB7200 tablet.

Signed-off-by Aleksei Mamlin <[email protected]>

There are some other u-boot USB patches pending which change how to enable the MUSB controller in the defconfig. So I'm going to hold of with merging this until those are merged.

Once those are merged I'll adjust your patch to the new Kconfig options to use and then merge it.

Regards,

Hans

Quoted 25 lines
---
  configs/Wexler_TAB7200_defconfig | 5 +++++
  1 file changed, 5 insertions(+)
configs/Wexler_TAB7200_defconfig +5 -0
index eadceb2..55e1b6b 100644
@@ -2,10 +2,15 @@ CONFIG_ARM=y
  CONFIG_ARCH_SUNXI=y
  CONFIG_MACH_SUN7I=y
  CONFIG_DRAM_CLK=384
+CONFIG_USB0_VBUS_PIN="PB9"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH4"
+CONFIG_AXP_GPIO=y
  CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:24,pclk_khz:33000,le:45,ri:210,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
  CONFIG_VIDEO_LCD_POWER="PH8"
  CONFIG_VIDEO_LCD_BL_EN="PH7"
  CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_USB_MUSB_SUNXI=y
  CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-wexler-tab7200"
  # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
  CONFIG_SPL=y