board/t1023rdb: add support for T1023RDB RevC

PATCH New Shengzhou Liu 2 participants 2 messages Jun 17, 2015 – Jul 31, 2015

Share & tools

Shengzhou Liu

author

2015-06-17 08:37 UTC #0 lore raw

PATCH v2 1/1 board/t1023rdb: add support for T1023RDB RevC

Add support for NOR flash and GPIO/I2C switch control on RevC.
- NOR support
- bank0/bank4 switch
- SD/eMMC switch
- board version

Signed-off-by Shengzhou Liu <[email protected]>

---
v2: updated rcw.

 board/freescale/t102xrdb/README        |  18 +++--
 board/freescale/t102xrdb/t1023_rcw.cfg |   2 +-
 board/freescale/t102xrdb/t102xrdb.c    | 141 ++++++++++++++++++++++++---------
 board/freescale/t102xrdb/t102xrdb.h    |   3 +-
 include/configs/T102xRDB.h             |  15 ++--
 5 files changed, 123 insertions(+), 56 deletions(-)

board/freescale/t102xrdb/README +11 -7

index 922450e..7d3794a 100644
@@ -70,6 +70,7 @@ Deep Sleep:	yes    no
 I2C controller: 4      3
 DDR:		64-bit 32-bit
 IFC:		32-bit 28-bit
+Package:	23x23  19x19
 
 
 T1024RDB board Overview

@@ -192,7 +193,7 @@ Software configurations and board settings
 	on T1024RDB:
 	   set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
 	on T1023RDB:
-	   set SW1[1:8] = '00010110', SW2[1] = '0', SW3[4] = '0' for NOR boot
+	   set SW1[1:8] = '00010111', SW2[1] = '1', SW3[4] = '0' for NOR boot
 
    Switching between default bank0 and alternate bank4 on NOR flash
    To change boot source to vbank4:

@@ -200,7 +201,7 @@ Software configurations and board settings
 	via software:   run command 'cpld reset altbank' in u-boot.
 	via DIP-switch: set SW3[5:7] = '100'
    on T1023RDB:
-	via software:   run command 'gpio vbank4' in u-boot.
+	via software:   run command 'switch bank4' in u-boot.
 	via DIP-switch: set SW3[5:7] = '100'
 
    To change boot source to vbank0:

@@ -208,7 +209,7 @@ Software configurations and board settings
 	via software:   run command 'cpld reset' in u-boot.
 	via DIP-Switch: set SW3[5:7] = '000'
    on T1023RDB:
-	via software:   run command 'gpio vbank0' in u-boot.
+	via software:   run command 'switch bank0' in u-boot.
 	via DIP-switch: set SW3[5:7] = '000'
 
 2. NAND Boot:

@@ -219,7 +220,7 @@ Software configurations and board settings
 	=> tftp 1000000 u-boot-with-spl-pbl.bin
 	=> nand erase 0 $filesize
 	=> nand write 1000000 0 $filesize
-	set SW1[1:8] = '10001000', SW2[1] = '1', SW3[4] = '1' for NAND boot
+	set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot
 
 3. SPI Boot:
    a. build PBL image for SPI boot

@@ -241,11 +242,14 @@ Software configurations and board settings
 	$ make
    b. program u-boot-with-spl-pbl.bin to SD/MMC card
 	=> tftp 1000000 u-boot-with-spl-pbl.bin
-	=> mmc write 1000000 8 0x800
+	=> mmc write 1000000 8 0x7f0
 	=> tftp 1000000 fsl_fman_ucode_t1024_xx.bin
 	=> mmc write 1000000 0x820 80
 	set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
 
+   SW3[3] = '1' for SD card(or 'switch sd' by software)
+   SW3[3] = '0' for eMMC (or 'switch emmc' by software)
+
 
 2-stage NAND/SPI/SD boot loader
 -------------------------------

@@ -292,7 +296,7 @@ Start		End		Definition	Size
 0x160000	0x17FFFF	FMAN Ucode	128KB
 
 
-SD Card memory Map on T1024RDB
+SD Card memory Map on T102xRDB
 ----------------------------------------------------
 Block		#blocks		Definition	Size
 0x008		2048		u-boot img	1MB

@@ -313,5 +317,5 @@ Start		End		Definition	Size
 0xa00000	0x3FFFFFF	rootfs		54MB
 
 
-For more details, please refer to T1024RDB Reference Manual
+For more details, please refer to T1024RDB/T1023RDB User Guide
 and Freescale QorIQ SDK Infocenter document.

board/freescale/t102xrdb/t1023_rcw.cfg +1 -1

index fa781d6..1d11a2e 100644
@@ -4,5 +4,5 @@ aa55aa55 010e0100
 #Core/DDR: 1400Mhz/1600MT/s with single source clock
 0810000e 00000000 00000000 00000000
 3b800003 00000012 e8104000 21000000
-00000000 00000000 00000000 00020800
+00000000 00000000 00000000 00022800
 00000130 04020200 00000000 00000006

board/freescale/t102xrdb/t102xrdb.c +104 ~~-37~~

204 lines not on this page · raw message

board/freescale/t102xrdb/t102xrdb.h +2 -1

index 3f5d85a..ae5c60f 100644
@@ -10,6 +10,7 @@
 void fdt_fixup_board_enet(void *blob);
 void pci_of_setup(void *blob, bd_t *bd);
 #ifdef CONFIG_T1023RDB
-static u32 t1023rdb_gpio_ctrl(u32 ctrl_type);
+static u32 t1023rdb_ctrl(u32 ctrl_type);
+static void fdt_enable_nor(void *blob);
 #endif
 #endif

include/configs/T102xRDB.h +5 ~~-10~~

index b871204..c62058c 100644
@@ -11,12 +11,6 @@
 #ifndef __T1024RDB_H
 #define __T1024RDB_H
 
-#if defined(CONFIG_T1023RDB)
-#ifdef CONFIG_SPL
-#define CONFIG_SYS_NO_FLASH
-#endif
-#endif
-
 /* High Level Configuration Options */
 #define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO

@@ -320,7 +314,7 @@ unsigned long get_board_ddr_clk(void);
 #if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
 #elif defined(CONFIG_T1023RDB)
-#define CONFIG_SYS_NOR_CSOR    (CSOR_NOR_ADM_SHIFT(4) | \
+#define CONFIG_SYS_NOR_CSOR    (CSOR_NOR_ADM_SHIFT(0) | \
 				CSOR_NAND_TRHZ_80 | CSOR_NOR_ADM_SHFT_MODE_EN)
 #endif
 #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \

@@ -560,9 +554,8 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x118100
 
-#define I2C_MUX_PCA_ADDR		0x77
-#define I2C_MUX_PCA_ADDR_PRI		0x77 /* Primary Mux*/
-
+#define I2C_PCA6408_BUS_NUM		1
+#define I2C_PCA6408_ADDR		0x20
 
 /* I2C bus multiplexer */
 #define I2C_MUX_CH_DEFAULT	0x8

@@ -761,8 +754,10 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_SYS_DPAA_FMAN
 
+#ifdef CONFIG_T1024RDB
 #define CONFIG_QE
 #define CONFIG_U_QE
+#endif
 /* Default address of microcode for the Linux FMan driver */
 #if defined(CONFIG_SPIFLASH)
 /*

Signature · 1 line

2.1.0.27.g96db324

York Sun

2015-07-31 15:53 UTC #1 lore raw

PATCH v2 1/1 board/t1023rdb: add support for T1023RDB RevC

Quoted 10 lines · Shengzhou Liu

Add support for NOR flash and GPIO/I2C switch control on RevC.
- NOR support
- bank0/bank4 switch
- SD/eMMC switch
- board version
Signed-off-by Shengzhou Liu <[email protected]>
---
v2: updated rcw.

Applied to u-boot-mpc85xx master after fixing subject.

Thanks.

York