imx: mx7dsabresd: Add support for MX7D SABRESD board

* Add i.MX7D SABRESD target board support with enabled modules:
UART, PMIC, USB/OTG, SD, eMMC, ENET, I2C, 74LV IOX.

Build target: mx7dsabresd_config

Signed-off-by Peng Fan <[email protected]>

Signed-off-by Fugang Duan <[email protected]>

Signed-off-by Ye.Li <[email protected]>

Signed-off-by Adrian Alonso <[email protected]>

---
Changes for V2:
- Include arch/arm/Kconfig target config option
Changes for V3:
- Update target board maintainer contact info
Changes for V4: depends on patchs
- mmc: fsl_esdhc invalidate dcache before read
- imx: usb: ehci-mx6: add usb support for imx7d soc Changes for V5: depends on patchs
- imx: usb: ehci-mx6: reg accessor cleanups
- imx: usb: ehci-mx6: document board specific functions
- imx: usb: ehci-mx6: wait_for_bit to check reg status Changes for V6:
- Remove unused macro CONFIG_BOARD_POSTCLK_INIT from mc7_common.h
- Depends on patchs:
- arm: imx-common: init: rework wdog settings for imx6/imx7
- arm: imx-common: init: extend init_aips to support imx7
- arm: imx: imx-common: init: move arch init common setup
- arm: imx: common rework cache settings for imx6
- thermal: imx_thermal: rework driver to be reused
- thermal: imx: add imx7d soc thermal support

 arch/arm/Kconfig                          |   7 +
 board/freescale/mx7dsabresd/Kconfig       |  15 +
 board/freescale/mx7dsabresd/MAINTAINERS   |   6 +
 board/freescale/mx7dsabresd/Makefile      |   6 +
 board/freescale/mx7dsabresd/imximage.cfg  | 103 +++++
 board/freescale/mx7dsabresd/mx7dsabresd.c | 642 ++++++++++++++++++++++++++++++
 configs/mx7dsabresd_defconfig             |  10 +
 include/configs/mx7_common.h              |  21 +
 include/configs/mx7dsabresd.h             | 355 +++++++++++++++++
 9 files changed, 1165 insertions(+)
 create mode 100644 board/freescale/mx7dsabresd/Kconfig
 create mode 100644 board/freescale/mx7dsabresd/MAINTAINERS
 create mode 100644 board/freescale/mx7dsabresd/Makefile
 create mode 100644 board/freescale/mx7dsabresd/imximage.cfg
 create mode 100644 board/freescale/mx7dsabresd/mx7dsabresd.c
 create mode 100644 configs/mx7dsabresd_defconfig
 create mode 100644 include/configs/mx7_common.h
 create mode 100644 include/configs/mx7dsabresd.h

arch/arm/Kconfig +7 -0

index a99ae28..416c784 100644
@@ -588,6 +588,12 @@ config TARGET_MX6UL_14X14_EVK
 	select DM_THERMAL
 	select SUPPORT_SPL
 
+config TARGET_MX7DSABRESD
+	bool "Support mx7dsabresd"
+	select CPU_V7
+	select DM
+	select DM_THERMAL
+
 config TARGET_GW_VENTANA
 	bool "Support gw_ventana"
 	select CPU_V7

@@ -935,6 +941,7 @@ source "board/freescale/mx6sabresd/Kconfig"
 source "board/freescale/mx6slevk/Kconfig"
 source "board/freescale/mx6sxsabresd/Kconfig"
 source "board/freescale/mx6ul_14x14_evk/Kconfig"
+source "board/freescale/mx7dsabresd/Kconfig"
 source "board/freescale/vf610twr/Kconfig"
 source "board/gateworks/gw_ventana/Kconfig"
 source "board/genesi/mx51_efikamx/Kconfig"

board/freescale/mx7dsabresd/Kconfig new file +15 -0

new file mode 100644
index 0000000..d7c6ae4
@@ -0,0 +1,15 @@
+if TARGET_MX7DSABRESD
+
+config SYS_BOARD
+	default "mx7dsabresd"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_SOC
+	default "mx7"
+
+config SYS_CONFIG_NAME
+	default "mx7dsabresd"
+
+endif

board/freescale/mx7dsabresd/MAINTAINERS new file +6 -0

new file mode 100644
index 0000000..3910ee4
@@ -0,0 +1,6 @@
+MX7DSABRESD BOARD
+M:	Adrian Alonso <[email protected]>
+S:	Maintained
+F:	board/freescale/mx7dsabresd
+F:	include/configs/mx7dsabresd.h
+F:	configs/mx7dsabresd_defconfig

board/freescale/mx7dsabresd/Makefile new file +6 -0

new file mode 100644
index 0000000..14336ab
@@ -0,0 +1,6 @@
+# (C) Copyright 2015 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := mx7dsabresd.o

board/freescale/mx7dsabresd/imximage.cfg new file +103 -0

new file mode 100644
index 0000000..5088d0e
@@ -0,0 +1,103 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+#ifdef CONFIG_SYS_BOOT_QSPI
+BOOT_FROM	qspi
+#elif defined(CONFIG_SYS_BOOT_EIMNOR)
+BOOT_FROM	nor
+#else
+BOOT_FROM	sd
+#endif
+
+#ifdef CONFIG_SECURE_BOOT
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x03040001
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x0040005e
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00020001
+DATA 4 0x307a00d4 0x00010000
+DATA 4 0x307a00dc 0x09300004
+DATA 4 0x307a00e0 0x04080000
+DATA 4 0x307a00e4 0x00090004
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x0908120a
+DATA 4 0x307a0104 0x0002020e
+DATA 4 0x307a0108 0x03040407
+DATA 4 0x307a010c 0x00002006
+DATA 4 0x307a0110 0x04020204
+DATA 4 0x307a0114 0x03030202
+DATA 4 0x307a0120 0x03030803
+DATA 4 0x307a0180 0x00800020
+DATA 4 0x307a0190 0x02098204
+DATA 4 0x307a0194 0x00030303
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00171717
+DATA 4 0x307a0214 0x04040404
+DATA 4 0x307a0218 0x00040404
+DATA 4 0x307a0240 0x06000601
+DATA 4 0x307a0244 0x00001323
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17420f40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790010 0x00060807
+DATA 4 0x3079009c 0x00000d6e
+DATA 4 0x30790020 0x08080808
+DATA 4 0x30790030 0x08080808
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e407304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+DATA 4 0x30790018 0x0000000f
+
+CHECK_BITS_SET 4 0x307a0004 0x1

board/freescale/mx7dsabresd/mx7dsabresd.c new file +221 -0

new file mode 100644
index 0000000..1d5928f
@@ -0,0 +1,642 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/io.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../common/pfuze.h"
+#include <i2c.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/arch/crm_regs.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
+	PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+#define ENET_PAD_CTRL_MII  (PAD_CTL_DSE_3P3V_32OHM)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+
+#define I2C_PAD_CTRL    (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
+
+#define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
+	PAD_CTL_DSE_3P3V_49OHM)
+
+#define QSPI_PAD_CTRL	\
+	(PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define SPI_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define BUTTON_PAD_CTRL    (PAD_CTL_PUS_PU5KOHM | PAD_CTL_DSE_3P3V_98OHM)
+
+#define NAND_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU5KOHM)
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C1 for PMIC */
+struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_I2C1_SCL__I2C1_SCL | PC,
+		.gpio_mode = MX7D_PAD_I2C1_SCL__GPIO4_IO8 | PC,
+		.gp = IMX_GPIO_NR(4, 8),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_I2C1_SDA__I2C1_SDA | PC,
+		.gpio_mode = MX7D_PAD_I2C1_SDA__GPIO4_IO9 | PC,
+		.gp = IMX_GPIO_NR(4, 9),
+	},
+};
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX7D_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_SD1_CD_B__GPIO5_IO0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_RESET_B__GPIO5_IO2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_emmc_pads[] = {
+	MX7D_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_STROBE__SD3_STROBE	 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#define IOX_SDI IMX_GPIO_NR(1, 9)
+#define IOX_STCP IMX_GPIO_NR(1, 12)
+#define IOX_SHCP IMX_GPIO_NR(1, 13)
+
+static iomux_v3_cfg_t const iox_pads[] = {
+	/* IOX_SDI */
+	MX7D_PAD_GPIO1_IO09__GPIO1_IO9	| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* IOX_STCP */
+	MX7D_PAD_GPIO1_IO12__GPIO1_IO12	| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* IOX_SHCP */
+	MX7D_PAD_GPIO1_IO13__GPIO1_IO13	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+/*
+ * PCIE_DIS_B --> Q0
+ * PCIE_RST_B --> Q1
+ * HDMI_RST_B --> Q2
+ * PERI_RST_B --> Q3
+ * SENSOR_RST_B --> Q4
+ * ENET_RST_B --> Q5
+ * PERI_3V3_EN --> Q6
+ * LCD_PWR_EN --> Q7
+ */
+enum qn {
+	PCIE_DIS_B,
+	PCIE_RST_B,
+	HDMI_RST_B,
+	PERI_RST_B,
+	SENSOR_RST_B,
+	ENET_RST_B,
+	PERI_3V3_EN,
+	LCD_PWR_EN,
+};
+
+enum qn_func {
+	qn_reset,
+	qn_enable,
+	qn_disable,
+};
+
+enum qn_level {
+	qn_low = 0,
+	qn_high = 1,
+};
+
+static enum qn_level seq[3][2] = {
+	{0, 1}, {1, 1}, {0, 0}
+};
+
+static enum qn_func qn_output[8] = {
+	qn_disable, qn_reset, qn_reset, qn_reset, qn_reset, qn_reset, qn_enable,
+	qn_enable
+};
+
+void iox74lv_init(void)
+{
+	int i;
+
+	for (i = 7; i >= 0; i--) {
+		gpio_direction_output(IOX_SHCP, 0);
+		gpio_direction_output(IOX_SDI, seq[qn_output[i]][0]);
+		udelay(500);
+		gpio_direction_output(IOX_SHCP, 1);
+		udelay(500);
+	}
+
+	gpio_direction_output(IOX_STCP, 0);
+	udelay(500);
+	/*
+	  * shift register will be output to pins
+	  */
+	gpio_direction_output(IOX_STCP, 1);
+
+	for (i = 7; i >= 0; i--) {
+		gpio_direction_output(IOX_SHCP, 0);
+		gpio_direction_output(IOX_SDI, seq[qn_output[i]][1]);
+		udelay(500);
+		gpio_direction_output(IOX_SHCP, 1);
+		udelay(500);
+	}
+	gpio_direction_output(IOX_STCP, 0);
+	udelay(500);
+	/*
+	  * shift register will be output to pins
+	  */
+	gpio_direction_output(IOX_STCP, 1);
+};
+
+void iox74lv_set(int index)
+{
+	int i;
+	for (i = 7; i >= 0; i--) {
+		gpio_direction_output(IOX_SHCP, 0);
+
+		if (i == index)
+			gpio_direction_output(IOX_SDI, seq[qn_output[i]][0]);
+		else
+			gpio_direction_output(IOX_SDI, seq[qn_output[i]][1]);
+		udelay(500);
+		gpio_direction_output(IOX_SHCP, 1);
+		udelay(500);
+	}
+

board/freescale/mx7dsabresd/mx7dsabresd.c new file +195 -0

+		udelay(500);
+		gpio_direction_output(IOX_SHCP, 1);
+		udelay(500);
+	}
+
+	gpio_direction_output(IOX_STCP, 0);
+	udelay(500);
+	/*
+	  * shift register will be output to pins
+	  */
+	gpio_direction_output(IOX_STCP, 1);
+};
+
+#ifdef CONFIG_SYS_USE_NAND
+static iomux_v3_cfg_t const gpmi_pads[] = {
+	MX7D_PAD_SD3_DATA0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_CLK__NAND_CLE	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__NAND_ALE	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_STROBE__NAND_RE_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_RESET_B__NAND_WE_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_MCLK__NAND_WP_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_RX_BCLK__NAND_CE3_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_RX_SYNC__NAND_CE2_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_RX_DATA__NAND_CE1_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_TX_SYNC__NAND_DQS	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	| MUX_PAD_CTRL(NAND_PAD_READY0_CTRL),
+};
+
+static void setup_gpmi_nand(void)
+{
+	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
+
+	/*
+	 * NAND_USDHC_BUS_CLK is set in rom
+	 */
+
+	set_clk_nand();
+
+	/*
+	 * APBH clock root is set in init_esdhc, USDHC3_CLK.
+	 * There is no clk gate for APBHDMA.
+	 * No touch here.
+	 */
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_GPIO1_IO10__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_GPIO1_IO11__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+};
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_FSL_QSPI
+static iomux_v3_cfg_t const quadspi_pads[] = {
+	MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK  | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+};
+
+int board_qspi_init(void)
+{
+	/* Set the iomux */
+	imx_iomux_v3_setup_multiple_pads(quadspi_pads, ARRAY_SIZE(quadspi_pads));
+
+	/* Set the clock */
+	set_clk_qspi();
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FSL_ESDHC
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(5, 0)
+#define USDHC1_PWR_GPIO	IMX_GPIO_NR(5, 2)
+#define USDHC3_PWR_GPIO IMX_GPIO_NR(6, 11)
+
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC1_BASE_ADDR, 0, 4},
+	{USDHC3_BASE_ADDR},
+};
+
+static int mmc_get_env_devno(void)
+{
+	struct bootrom_sw_info **p =
+		(struct bootrom_sw_info **)ROM_SW_INFO_ADDR;
+
+	u8 boot_type = (*p)->boot_dev_type;
+	u8 dev_no = (*p)->boot_dev_instance;
+
+	/* If not boot from sd/mmc, use default value */
+	if ((boot_type != BOOT_TYPE_SD) && (boot_type != BOOT_TYPE_MMC))
+		return CONFIG_SYS_MMC_ENV_DEV;
+
+	if (2 == dev_no)
+		dev_no--;
+
+	return dev_no;
+}
+
+static int mmc_map_to_kernel_blk(int dev_no)
+{
+	if (1 == dev_no)
+		dev_no++;
+
+	return dev_no;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = 1; /* Assume uSDHC3 emmc is always present */
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 * mmc2                    USDHC3 (eMMC)
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+			gpio_request(USDHC1_CD_GPIO, "usdhc1_cd");
+			gpio_direction_input(USDHC1_CD_GPIO);
+			gpio_request(USDHC1_PWR_GPIO, "usdhc1_pwr");
+			gpio_direction_output(USDHC1_PWR_GPIO, 0);
+			udelay(500);
+			gpio_direction_output(USDHC1_PWR_GPIO, 1);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_emmc_pads, ARRAY_SIZE(usdhc3_emmc_pads));
+			gpio_request(USDHC3_PWR_GPIO, "usdhc3_pwr");
+			gpio_direction_output(USDHC3_PWR_GPIO, 0);
+			udelay(500);
+			gpio_direction_output(USDHC3_PWR_GPIO, 1);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return -EINVAL;
+			}

board/freescale/mx7dsabresd/mx7dsabresd.c new file +101 -0

+{
+	char cmd[32];
+	char mmcblk[32];
+	u32 dev_no = mmc_get_env_devno();
+
+	if (!check_mmc_autodetect())
+		return;
+
+	setenv_ulong("mmcdev", dev_no);
+
+	/* Set mmcblk env */
+	sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw",
+		mmc_map_to_kernel_blk(dev_no));
+	setenv("mmcroot", mmcblk);
+
+	sprintf(cmd, "mmc dev %d", dev_no);
+	run_command(cmd, 0);
+}
+
+#endif
+
+#ifdef CONFIG_FEC_MXC
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+
+	setup_iomux_fec();
+
+	ret = fecmxc_initialize_multi(bis, 0,
+		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+	if (ret)
+		printf("FEC1 MXC: %s:failed\n", __func__);
+
+	return ret;
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
+
+	/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+		(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
+		 IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
+
+	return set_clk_enet(ENET_125MHz);
+}
+
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* enable rgmii rxc skew and phy mode select to RGMII copper */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x21);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x7ea8);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x2f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x71b7);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+	return 0;
+}
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	imx_iomux_v3_setup_multiple_pads(iox_pads, ARRAY_SIZE(iox_pads));
+
+	iox74lv_init();
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+#ifdef CONFIG_SYS_USE_NAND
+	setup_gpmi_nand();
+#endif
+
+#ifdef CONFIG_FSL_QSPI
+	board_qspi_init();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd1", MAKE_CFGVAL(0x10, 0x10, 0x00, 0x00)},

board/freescale/mx7dsabresd/mx7dsabresd.c new file +83 -0

+{
+	struct pmic *p;
+	int ret;
+	unsigned int reg, rev_id;
+
+	ret = power_pfuze3000_init(I2C_PMIC);
+	if (ret)
+		return ret;
+
+	p = pmic_get("PFUZE3000");
+	ret = pmic_probe(p);
+	if (ret)
+		return ret;
+
+	pmic_reg_read(p, PFUZE3000_DEVICEID, &reg);
+	pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
+	printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	pmic_reg_read(p, PFUZE3000_LDOGCTL, &reg);
+	reg |= 0x1;
+	pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
+
+	return 0;
+}
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_init();
+#endif
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset((struct wdog_regs *)WDOG1_BASE_ADDR);
+
+	return 0;
+}
+
+u32 get_board_rev(void)
+{
+	return get_cpu_rev();
+}
+
+int checkboard(void)
+{
+	puts("Board: i.MX7D SABRESD\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_USB_EHCI_MX7
+iomux_v3_cfg_t const usb_otg1_pads[] = {
+	MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const usb_otg2_pads[] = {
+	MX7D_PAD_UART3_CTS_B__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_ehci_hcd_init(int port)
+{
+	switch (port) {
+	case 0:
+		imx_iomux_v3_setup_multiple_pads(usb_otg1_pads,
+						 ARRAY_SIZE(usb_otg1_pads));
+		break;
+	case 1:
+		imx_iomux_v3_setup_multiple_pads(usb_otg2_pads,
+						 ARRAY_SIZE(usb_otg2_pads));
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n", port);
+		return -EINVAL;
+	}
+	return 0;
+}
+#endif

configs/mx7dsabresd_defconfig new file +10 -0

new file mode 100644
index 0000000..879847c
@@ -0,0 +1,10 @@
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg,MX7D"
+CONFIG_ARM=y
+CONFIG_TARGET_MX7DSABRESD=y
+CONFIG_SYS_MALLOC_F=y
+CONFIG_SYS_MALLOC_F_LEN=0x400
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set

include/configs/mx7_common.h new file +21 -0

new file mode 100644
index 0000000..3747237
@@ -0,0 +1,21 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX7.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+
+#ifndef __MX7_COMMON_H
+#define __MX7_COMMON_H
+
+#define CONFIG_MXC_GPT_HCLK
+
+#define CONFIG_SYSCOUNTER_TIMER
+#define CONFIG_SC_TIMER_CLK 8000000 /* 8Mhz */
+
+#define CONFIG_IOMUX_LPSR
+#define CONFIG_IMX_FIXED_IVT_OFFSET
+
+#endif

include/configs/mx7dsabresd.h new file +24 -0

new file mode 100644
index 0000000..b84590a
@@ -0,0 +1,355 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX7D SABRESD board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MX7D_SABRESD_CONFIG_H
+#define __MX7D_SABRESD_CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <linux/sizes.h>
+#include "mx7_common.h"
+#include <asm/imx-common/gpio.h>
+
+#define CONFIG_MX7
+#define CONFIG_ROM_UNIFIED_SECTIONS
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_DBG_MONITOR
+/* uncomment for PLUGIN mode support */

include/configs/mx7dsabresd.h new file +159 -0

+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
+
+#define PHYS_SDRAM_SIZE			SZ_1G
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define CONFIG_FEC_XCV_TYPE             RGMII
+#define CONFIG_ETHPRIME                 "FEC"
+#define CONFIG_FEC_MXC_PHYADDR          0
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_BROADCOM
+#define CONFIG_FEC_DMA_MINALIGN		64
+
+/* ENET1 */
+#define IMX_FEC_BASE			ENET_IPS_BASE_ADDR
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE3000
+#define CONFIG_POWER_PFUZE3000_I2C_ADDR	0x08
+
+#undef CONFIG_BOOTM_NETBSD
+#undef CONFIG_BOOTM_PLAN9
+#undef CONFIG_BOOTM_RTEMS
+
+#undef CONFIG_CMD_EXPORTENV
+#undef CONFIG_CMD_IMPORTENV
+
+/* I2C configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_SPEED		100000
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY		3
+
+#define CONFIG_LOADADDR			0x80800000
+#define CONFIG_SYS_TEXT_BASE		0x87800000
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+#ifdef CONFIG_SYS_BOOT_NAND
+#define CONFIG_MFG_NAND_PARTITION "mtdparts=gpmi-nand:64m(boot),16m(kernel),16m(dtb),-(rootfs) "
+#else
+#define CONFIG_MFG_NAND_PARTITION ""
+#endif
+
+#define CONFIG_MFG_ENV_SETTINGS \
+	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
+		"rdinit=/linuxrc " \
+		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
+		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
+		"g_mass_storage.iSerialNumber=\"\" "\
+		CONFIG_MFG_NAND_PARTITION \
+		"clk_ignore_unused "\
+		"\0" \
+	"initrd_addr=0x83800000\0" \
+	"initrd_high=0xffffffff\0" \
+	"bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
+
+#if defined(CONFIG_SYS_BOOT_NAND)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_MFG_ENV_SETTINGS \
+	"fdt_addr=0x83000000\0" \
+	"fdt_high=0xffffffff\0"	  \
+	"console=ttymxc0\0" \
+	"bootargs=console=ttymxc0,115200 ubi.mtd=3 "  \
+		"root=ubi0:rootfs rootfstype=ubifs "		     \
+		"mtdparts=gpmi-nand:64m(boot),16m(kernel),16m(dtb),-(rootfs)\0"\
+	"bootcmd=nand read ${loadaddr} 0x4000000 0x800000;"\
+		"nand read ${fdt_addr} 0x5000000 0x100000;"\
+		"bootz ${loadaddr} - ${fdt_addr}\0"
+
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_MFG_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc0\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"fdt_file=imx7d-sdb.dtb\0" \
+	"fdt_addr=0x83000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+		"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev};" \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \

include/configs/mx7dsabresd.h new file +117 -0

+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE		1024
+#define CONFIG_SYS_MAXARGS		256
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x20000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE		SZ_128K
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE			SZ_8K
+
+#ifdef CONFIG_SYS_BOOT_QSPI
+#define CONFIG_SYS_USE_QSPI
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#elif defined CONFIG_SYS_BOOT_NAND
+#define CONFIG_SYS_USE_NAND
+#define CONFIG_ENV_IS_IN_NAND
+#else
+#define CONFIG_ENV_IS_IN_MMC
+#endif
+
+#ifdef CONFIG_SYS_USE_NAND
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+
+/* NAND stuff */
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+#endif
+
+#ifdef CONFIG_SYS_USE_QSPI
+#define CONFIG_FSL_QSPI    /* enable the QUADSPI driver */
+#define CONFIG_QSPI_BASE		QSPI1_IPS_BASE_ADDR
+#define CONFIG_QSPI_MEMMAP_BASE		QSPI0_ARB_BASE_ADDR
+
+#define CONFIG_CMD_SF
+#define	CONFIG_SPI_FLASH
+#define	CONFIG_SPI_FLASH_MACRONIX
+#define	CONFIG_SPI_FLASH_BAR
+#define	CONFIG_SF_DEFAULT_BUS		0
+#define	CONFIG_SF_DEFAULT_CS		0
+#define	CONFIG_SF_DEFAULT_SPEED		40000000
+#define	CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#endif
+
+#if defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
+#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
+#define CONFIG_ENV_OFFSET		(768 * 1024)
+#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
+#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
+#elif defined(CONFIG_ENV_IS_IN_NAND)
+#undef CONFIG_ENV_SIZE
+#define CONFIG_ENV_OFFSET		(8 << 20)
+#define CONFIG_ENV_SECT_SIZE		(128 << 10)
+#define CONFIG_ENV_SIZE			CONFIG_ENV_SECT_SIZE
+#endif
+
+#ifdef CONFIG_SYS_USE_NAND
+#define CONFIG_SYS_FSL_USDHC_NUM	1
+#else
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+#endif
+#define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC1 */
+#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
+#define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC1 */
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+
+#define CONFIG_CMD_BMODE
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX7
+#define CONFIG_USB_STORAGE