arm: socfpga: Add support for the Terasic DE-0 Atlas board
Subsystems (3)
PATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
---
v2: add ethernet support
moved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or 'de0_nano_soc' based on u-boot-socfpga/wip/boards branch
--- arch/arm/dts/Makefile | 1 + arch/arm/dts/socfpga_cyclone5_de0_nano_soc.dts | 61 +++ arch/arm/mach-socfpga/Kconfig | 7 + board/terasic/de0-nano-soc/MAINTAINERS | 5 + board/terasic/de0-nano-soc/Makefile | 9 + board/terasic/de0-nano-soc/qts/iocsr_config.h | 658 +++++++++++++++++++++++++ board/terasic/de0-nano-soc/qts/pinmux_config.h | 220 +++++++++ board/terasic/de0-nano-soc/qts/pll_config.h | 85 ++++ board/terasic/de0-nano-soc/qts/sdram_config.h | 342 +++++++++++++ board/terasic/de0-nano-soc/socfpga.c | 72 +++ configs/socfpga_de0_nano_soc_defconfig | 20 + include/configs/socfpga_de0_nano_soc.h | 87 ++++ 12 files changed, 1567 insertions(+) create mode 100644 arch/arm/dts/socfpga_cyclone5_de0_nano_soc.dts create mode 100644 board/terasic/de0-nano-soc/MAINTAINERS create mode 100644 board/terasic/de0-nano-soc/Makefile create mode 100644 board/terasic/de0-nano-soc/qts/iocsr_config.h create mode 100644 board/terasic/de0-nano-soc/qts/pinmux_config.h create mode 100644 board/terasic/de0-nano-soc/qts/pll_config.h create mode 100644 board/terasic/de0-nano-soc/qts/sdram_config.h create mode 100644 board/terasic/de0-nano-soc/socfpga.c create mode 100644 configs/socfpga_de0_nano_soc_defconfig create mode 100644 include/configs/socfpga_de0_nano_soc.h
arch/arm/dts/Makefile +1 -0
@@ -58,6 +58,7 @@ dtb-$(CONFIG_ARCH_SOCFPGA) += \ socfpga_arria5_socdk.dtb \ socfpga_cyclone5_mcvevk.dtb \ socfpga_cyclone5_socdk.dtb \ + socfpga_cyclone5_de0_nano_soc.dtb \ socfpga_cyclone5_sockit.dtb \ socfpga_cyclone5_socrates.dtb dtb-$(CONFIG_TARGET_DRA7XX_EVM) += dra72-evm.dtb
arch/arm/dts/socfpga_cyclone5_de0_nano_soc.dts new file +61 -0
61 lines not on this page · raw message
arch/arm/mach-socfpga/Kconfig +7 -0
@@ -18,6 +18,10 @@ config TARGET_SOCFPGA_CYCLONE5_SOCDK bool "Altera SOCFPGA SoCDK (Cyclone V)" select TARGET_SOCFPGA_CYCLONE5 +config TARGET_SOCFPGA_TERASIC_DE0_NANO + bool "Terasic DE0-Nano-Atlas (Cyclone V)" + select TARGET_SOCFPGA_CYCLONE5 + config TARGET_SOCFPGA_TERASIC_SOCKIT bool "Terasic SoCkit (Cyclone V)" select TARGET_SOCFPGA_CYCLONE5
@@ -31,12 +35,14 @@ endchoice config SYS_BOARD default "arria5-socdk" if TARGET_SOCFPGA_ARRIA5_SOCDK default "cyclone5-socdk" if TARGET_SOCFPGA_CYCLONE5_SOCDK + default "de0-nano-soc" if TARGET_SOCFPGA_TERASIC_DE0_NANO default "sockit" if TARGET_SOCFPGA_TERASIC_SOCKIT default "mcvevk" if TARGET_SOCFPGA_DENX_MCVEVK config SYS_VENDOR default "altera" if TARGET_SOCFPGA_ARRIA5_SOCDK default "altera" if TARGET_SOCFPGA_CYCLONE5_SOCDK + default "terasic" if TARGET_SOCFPGA_TERASIC_DE0_NANO default "terasic" if TARGET_SOCFPGA_TERASIC_SOCKIT default "denx" if TARGET_SOCFPGA_DENX_MCVEVK
@@ -46,6 +52,7 @@ config SYS_SOC config SYS_CONFIG_NAME default "socfpga_arria5" if TARGET_SOCFPGA_ARRIA5_SOCDK default "socfpga_cyclone5" if TARGET_SOCFPGA_CYCLONE5_SOCDK + default "socfpga_de0_nano_soc" if TARGET_SOCFPGA_TERASIC_DE0_NANO default "socfpga_sockit" if TARGET_SOCFPGA_TERASIC_SOCKIT default "socfpga_mcvevk" if TARGET_SOCFPGA_DENX_MCVEVK
board/terasic/de0-nano-soc/MAINTAINERS new file +5 -0
@@ -0,0 +1,5 @@ +SOCFPGA ATLAS BOARD +M: Dinh Nguyen <[email protected]> +S: Maintained +F: include/configs/socfpga_de0_nano_soc.h +F: configs/socfpga_de0_nano_soc_defconfig
board/terasic/de0-nano-soc/Makefile new file +9 -0
@@ -0,0 +1,9 @@ +# +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# (C) Copyright 2010, Thomas Chou <[email protected]> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := socfpga.o
board/terasic/de0-nano-soc/qts/iocsr_config.h new file +658 -0
658 lines not on this page · raw message
board/terasic/de0-nano-soc/qts/pinmux_config.h new file +220 -0
220 lines not on this page · raw message
board/terasic/de0-nano-soc/qts/pll_config.h new file +85 -0
85 lines not on this page · raw message
board/terasic/de0-nano-soc/qts/sdram_config.h new file +342 -0
342 lines not on this page · raw message
board/terasic/de0-nano-soc/socfpga.c new file +72 -0
72 lines not on this page · raw message
configs/socfpga_de0_nano_soc_defconfig new file +20 -0
@@ -0,0 +1,20 @@ +CONFIG_ARM=y +CONFIG_ARCH_SOCFPGA=y +CONFIG_TARGET_SOCFPGA_CYCLONE5=y +CONFIG_TARGET_SOCFPGA_TERASIC_DE0_NANO=y +CONFIG_DEFAULT_DEVICE_TREE="socfpga_cyclone5_de0_nano_soc" +CONFIG_SPL=y +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_OF_CONTROL=y +CONFIG_DM_ETH=y +CONFIG_NETDEVICES=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_DM_GPIO=y +CONFIG_DWAPB_GPIO=y +CONFIG_SPL_DM=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SIMPLE_BUS=y +CONFIG_SPL_STACK_R=y +CONFIG_SPL_STACK_R_ADDR=0x00800000 +CONFIG_SYS_MALLOC_F_LEN=0x2000
include/configs/socfpga_de0_nano_soc.h new file +87 -0
87 lines not on this page · raw message
Signature · 1 line
2.4.5
PATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
Quoted 5 lines · dinguyen at opensource.altera.com
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
Quoted 7 lines
Signed-off-by Dinh Nguyen <[email protected]>---
v2: add ethernet support
moved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or 'de0_nano_soc' based on u-boot-socfpga/wip/boards branch
---
Marek Vasut
AppliedPATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
In reply to dinguyen at opensource.altera.comQuoted 11 lines · dinguyen at opensource.altera.com
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by Dinh Nguyen <[email protected]>---
v2: add ethernet support
moved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or 'de0_nano_soc' based on u-boot-socfpga/wip/boards branch
Applied to wip/boards, thanks. I shuffled the order in arch/arm/mach- socfpga/Kconfig so that things are sorted properly. Can you please double-check that everything builds for you ?
Best regards,
Marek Vasut
PATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
Quoted 14 lines · Marek Vasut
Quoted 11 lines · dinguyen at opensource.altera.com
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by Dinh Nguyen <[email protected]>---
v2: add ethernet support
moved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or 'de0_nano_soc' based on u-boot-socfpga/wip/boards branch
Quoted 4 lines
Applied to wip/boards, thanks. I shuffled the order in
arch/arm/mach-socfpga/Kconfig so that things are sorted properly. Can you please double-check that everything builds for you ?
Yes, everything builds for me. Thanks!
Dinh
PATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
Quoted 18 lines · Dinh Nguyen
Quoted 17 lines · Marek Vasut
On Wednesday, September 02, 2015 at 12:41:52 AM,
dinguyen at opensource.altera.comQuoted 12 lines · wrote:
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by Dinh Nguyen <[email protected]>---
v2: add ethernet supportmoved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or '
de0_nano_soc' based on u-boot-socfpga/wip/boards branch
Quoted 5 lines
Quoted 3 lines
Applied to wip/boards, thanks. I shuffled the order in
arch/arm/mach-socfpga/Kconfig so that things are sorted properly. Can you please double-check that everything builds for you ?Yes, everything builds for me. Thanks!
Cool, thanks :)
Best regards,
Marek Vasut
PATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
In reply to Dinh NguyenQuoted 17 lines · Dinh Nguyen
Quoted 14 lines · Marek Vasut
Quoted 11 lines · dinguyen at opensource.altera.com
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by Dinh Nguyen <[email protected]>---
v2: add ethernet support
moved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or 'de0_nano_soc' based on u-boot-socfpga/wip/boards branch
Quoted 6 lines
Quoted 4 lines
Applied to wip/boards, thanks. I shuffled the order in
arch/arm/mach-socfpga/Kconfig so that things are sorted properly. Can you please double-check that everything builds for you ?Yes, everything builds for me. Thanks!
Hi Dinh
FYI, I just pulled from wip/boards and built withsocfpga_de0_nano_soc_defconfig and booted from SD :
U-Boot SPL 2015.10-rc2-00311-g859de28-dirty (Sep 02 2015 - 14:47:55)
drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration complete
bad magic
spl: mmc: no boot mode left to try
### ERROR ### Please RESET the board ###
Not sure what I have missed.
Regards
Sinan Akman
PATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
Quoted 39 lines · Sinan Akman
Quoted 19 lines · Dinh Nguyen
Quoted 18 lines · Marek Vasut
On Wednesday, September 02, 2015 at 12:41:52 AM,
dinguyen at opensource.altera.comQuoted 13 lines · wrote:
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by Dinh Nguyen <[email protected]>---
v2: add ethernet supportmoved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or '
de0_nano_soc' based on u-boot-socfpga/wip/boards branchQuoted 5 lines
Quoted 3 lines
Applied to wip/boards, thanks. I shuffled the order in
arch/arm/mach-socfpga/Kconfig so that things are sorted properly. Can you please double-check that everything builds for you ?Yes, everything builds for me. Thanks!
Hi Dinh
FYI, I just pulled from wip/boards and built with
socfpga_de0_nano_soc_defconfigand booted from SD :U-Boot SPL 2015.10-rc2-00311-g859de28-dirty (Sep 02 2015 - 14:47:55)
drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration complete
Quoted 7 lines
bad magic
spl: mmc: no boot mode left to try
### ERROR ### Please RESET the board ###
Not sure what I have missed.
Try the following:
git revert 811c9a20823a55decc5e15af0684d3d29cdf610f
and let me know if this fixes things for you.
Best regards,
Marek Vasut
PATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
Quoted 47 lines · Marek Vasut
Quoted 46 lines · Sinan Akman
Quoted 19 lines · Dinh Nguyen
Quoted 18 lines · Marek Vasut
On Wednesday, September 02, 2015 at 12:41:52 AM,
dinguyen at opensource.altera.comQuoted 13 lines · wrote:
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by Dinh Nguyen <[email protected]>---
v2: add ethernet supportmoved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or '
de0_nano_soc' based on u-boot-socfpga/wip/boards branchQuoted 6 lines
Quoted 3 lines
Applied to wip/boards, thanks. I shuffled the order in
arch/arm/mach-socfpga/Kconfig so that things are sorted properly. Can you please double-check that everything builds for you ?Yes, everything builds for me. Thanks!
Hi Dinh
FYI, I just pulled from wip/boards and built with
socfpga_de0_nano_soc_defconfigand booted from SD :U-Boot SPL 2015.10-rc2-00311-g859de28-dirty (Sep 02 2015 - 14:47:55)
drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration completebad magic
spl: mmc: no boot mode left to try
### ERROR ### Please RESET the board ###
Quoted 7 lines
Quoted 1 line
Not sure what I have missed.
Try the following:
git revert
811c9a20823a55decc5e15af0684d3d29cdf610fand let me know if this fixes things for you.
If this doesn't help, undo the revert and repartition the SD card such that the preloader partition is located at 2048 sectors from start (that's where U-Boot expects it for now, there's space for improvement) and write the u-boot-with-spl-dtb.sfp to that partition.
$ sudo fdisk -l /dev/sdg Disk /dev/sdg: 14.9 GiB, 16003891200 bytes, 31257600 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x5452574f
Device Boot Start End Sectors Size Id Type/dev/sdg1 * 2048 4095 2048 1M a2 unknown/dev/sdg2 6144 104447 98304 48M 83 Linux/dev/sdg3 106496 108543 2048 1M 83 Linux
Best regards,
Marek Vasut
PATCH v2 1/1 arm: socfpga: Add support for the Terasic DE-0 Atlas board
Quoted 66 lines · Marek Vasut
Quoted 43 lines · Marek Vasut
Quoted 42 lines · Sinan Akman
Quoted 15 lines · Dinh Nguyen
Quoted 14 lines · Marek Vasut
On Wednesday, September 02, 2015 at 12:41:52 AM,
dinguyen at opensource.altera.comQuoted 10 lines · wrote:
From: Dinh Nguyen <[email protected]>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by Dinh Nguyen <[email protected]>---
v2: add ethernet supportQuoted 8 lines
Quoted 6 lines
Quoted 3 lines
moved board files to board/terasic/de0-nano-soc/ associate everything with 'de0-nano-soc' or '
de0_nano_soc' based on u-boot-socfpga/wip/boards branchApplied to wip/boards, thanks. I shuffled the order in
arch/arm/mach-socfpga/Kconfig so that things are sorted properly. Can you please double-check that everything builds for you ?Yes, everything builds for me. Thanks!
Hi Dinh
FYI, I just pulled from wip/boards and built with
socfpga_de0_nano_soc_defconfigand booted from SD :U-Boot SPL 2015.10-rc2-00311-g859de28-dirty (Sep 02 2015 - 14:47:55)
drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration completebad magic
spl: mmc: no boot mode left to try
Quoted 8 lines
Quoted 3 lines
### ERROR ### Please RESET the board ###
Not sure what I have missed.
Try the following:
git revert
811c9a20823a55decc5e15af0684d3d29cdf610fand let me know if this fixes things for you.
If this doesn't help, undo the revert and repartition the SD card such that the preloader partition is located at 2048 sectors from start (that's where U-Boot expects it for now, there's space for improvement) and write the u-boot-with-spl-dtb.sfp to that partition.
$ sudo fdisk -l /dev/sdg Disk /dev/sdg: 14.9 GiB, 16003891200 bytes, 31257600 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x5452574f
Quoted 4 lines
Device Boot Start End Sectors Size Id Type
/dev/sdg1* 2048 4095 2048 1M a2 unknown/dev/sdg26144 104447 98304 48M 83 Linux/dev/sdg3106496 108543 2048 1M 83 Linux
I repartitioned SD with similar geometry and it boots
fine now.
Thanks
Sinan Akman