imx: mx7dsabresd: Add support for MX7D SABRESD board
Subsystems (2)
PATCH v3 13/13 imx: mx7dsabresd: Add support for MX7D SABRESD board
* Add i.MX7D SABRESD target board support with enabled modules:
UART, PMIC, USB/OTG, SD, eMMC, ENET, I2C, 74LV IOX.
Build target: mx7dsabresd_config
---
Changes for V2:
- Include arch/arm/Kconfig target config option
Changes for V3:
- Update target board maintainer contact info
Changes for V4: depends on patchs
- mmc: fsl_esdhc invalidate dcache before read
- imx: usb: ehci-mx6: add usb support for imx7d soc
Changes for V5: depends on patchs
- imx: usb: ehci-mx6: reg accessor cleanups
- imx: usb: ehci-mx6: document board specific functions
- imx: usb: ehci-mx6: wait_for_bit to check reg status
Changes for V6:
- Remove unused macro CONFIG_BOARD_POSTCLK_INIT from mc7_common.h Changes for V7:
- Update target config build settings
- Update mx7_common.h header file to gropup common build options for iMX7 SoC Changes for V8: Resend
Changes for V9:
- Remove non yet completely supported boot device options qspi, nand, to be reintroduced in future patch sets.
arch/arm/Kconfig | 6 + arch/arm/cpu/armv7/mx7/Kconfig | 27 ++ arch/arm/include/asm/arch-mx7/sys_proto.h | 2 + board/freescale/mx7dsabresd/Kconfig | 15 + board/freescale/mx7dsabresd/MAINTAINERS | 6 + board/freescale/mx7dsabresd/Makefile | 6 + board/freescale/mx7dsabresd/imximage.cfg | 94 +++++ board/freescale/mx7dsabresd/mx7dsabresd.c | 555 ++++++++++++++++++++++++++++++ configs/mx7dsabresd_defconfig | 14 + include/configs/mx7_common.h | 95 +++++ include/configs/mx7dsabresd.h | 194 +++++++++++ 11 files changed, 1014 insertions(+) create mode 100644 arch/arm/cpu/armv7/mx7/Kconfig create mode 100644 board/freescale/mx7dsabresd/Kconfig create mode 100644 board/freescale/mx7dsabresd/MAINTAINERS create mode 100644 board/freescale/mx7dsabresd/Makefile create mode 100644 board/freescale/mx7dsabresd/imximage.cfg create mode 100644 board/freescale/mx7dsabresd/mx7dsabresd.c create mode 100644 configs/mx7dsabresd_defconfig create mode 100644 include/configs/mx7_common.h create mode 100644 include/configs/mx7dsabresd.h
arch/arm/Kconfig +6 -0
@@ -472,6 +472,10 @@ config ARCH_KEYSTONE select CPU_V7 select SUPPORT_SPL +config ARCH_MX7 + bool "Freescale MX7" + select CPU_V7 + config ARCH_MX6 bool "Freescale MX6" select CPU_V7
@@ -751,6 +755,8 @@ source "arch/arm/mach-keystone/Kconfig" source "arch/arm/mach-kirkwood/Kconfig" +source "arch/arm/cpu/armv7/mx7/Kconfig" + source "arch/arm/cpu/armv7/mx6/Kconfig" source "arch/arm/cpu/armv7/mx5/Kconfig"
arch/arm/cpu/armv7/mx7/Kconfig new file +27 -0
@@ -0,0 +1,27 @@ +if ARCH_MX7 + +config MX7 + bool + default y + +config MX7D + bool + +choice + prompt "MX7 board select" + optional + +config TARGET_MX7DSABRESD + bool "mx7dsabresd" + select CPU_V7 + select DM + select DM_THERMAL + +endchoice + +config SYS_SOC + default "mx7" + +source "board/freescale/mx7dsabresd/Kconfig" + +endif
arch/arm/include/asm/arch-mx7/sys_proto.h +2 -0
@@ -5,3 +5,5 @@*/ #include <asm/imx-common/sys_proto.h> + +void set_wdog_reset (struct wdog_regs *wdog);
board/freescale/mx7dsabresd/Kconfig new file +15 -0
@@ -0,0 +1,15 @@ +if TARGET_MX7DSABRESD + +config SYS_BOARD + default "mx7dsabresd" + +config SYS_VENDOR + default "freescale" + +config SYS_SOC + default "mx7" + +config SYS_CONFIG_NAME + default "mx7dsabresd" + +endif
board/freescale/mx7dsabresd/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +MX7DSABRESD BOARD +M: Adrian Alonso <[email protected]> +S: Maintained +F: board/freescale/mx7dsabresd +F: include/configs/mx7dsabresd.h +F: configs/mx7dsabresd_defconfig
board/freescale/mx7dsabresd/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# (C) Copyright 2015 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := mx7dsabresd.o
board/freescale/mx7dsabresd/imximage.cfg new file +94 -0
94 lines not on this page · raw message
board/freescale/mx7dsabresd/mx7dsabresd.c new file +555 -0
555 lines not on this page · raw message
configs/mx7dsabresd_defconfig new file +14 -0
@@ -0,0 +1,14 @@ +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg,MX7D" +CONFIG_ARM=y +CONFIG_ARCH_MX7=y +CONFIG_TARGET_MX7DSABRESD=y +CONFIG_SYS_MALLOC_F=y +CONFIG_SYS_MALLOC_F_LEN=0x400 +CONFIG_CMD_NET=y +CONFIG_CMD_PING=y +CONFIG_CMD_DHCP=y +# CONFIG_CMD_BOOTD is not set +# CONFIG_CMD_SETEXPR is not set +# CONFIG_CMD_IMI is not set +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_XIMG is not set
include/configs/mx7_common.h new file +95 -0
95 lines not on this page · raw message
include/configs/mx7dsabresd.h new file +194 -0
194 lines not on this page · raw message
Signature · 1 line
2.1.4
PATCH v3 13/13 imx: mx7dsabresd: Add support for MX7D SABRESD board
Quoted 10 lines · Adrian Alonso
* Add i.MX7D SABRESD target board support with enabled modules:
UART, PMIC, USB/OTG, SD, eMMC, ENET, I2C, 74LV IOX.Build target:
mx7dsabresd_configSigned-off-by Peng Fan <[email protected]>Signed-off-by Fugang Duan <[email protected]>Signed-off-by Ye.Li <[email protected]>Signed-off-by Adrian Alonso <[email protected]>---
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================