Skip to contentSkip to conversation

drm/i915: Consider SPLL as another shared pll.

RFC PATCH In review Maarten Lankhorst 4 participants 6 messages Sep 16, 2015 – Nov 13, 2015

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/1 drm/i915: Consider SPLL as another shared pll.

When diagnosing a unrelated bug for someone on irc, it would seem the hardware can be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.

Right now this is not handled well in i915, and it calculates the crtc needs to be reprogrammed on the first modeset without SSC, but the SPLL itself was kept active. Fix this by exposing SPLL as a shared pll that will not be returned by intel_get_shared_dpll; you have to know it exists to use it. ;-)

Cc Emil Renner Berthing <[email protected]>

---
RFC because I haven't tested it with VGA, but it seems to work according to fix the problem mentioned above.

drivers/gpu/drm/i915/i915_drv.h +2 -0
index 81adf89b92f1..cacdac67d9ba 100644
@@ -345,6 +345,8 @@ enum intel_dpll_id {
 	/* hsw/bdw */
 	DPLL_ID_WRPLL1 = 0,
 	DPLL_ID_WRPLL2 = 1,
+	DPLL_ID_SPLL = 2,
+
 	/* skl */
 	DPLL_ID_SKL_DPLL1 = 0,
 	DPLL_ID_SKL_DPLL2 = 1,
drivers/gpu/drm/i915/intel_crt.c +2 -27
index af5e43bef4a4..592d8fe9f991 100644
@@ -138,18 +138,6 @@ static void hsw_crt_get_config(struct intel_encoder *encoder,
 	pipe_config->base.adjusted_mode.flags |= intel_crt_get_flags(encoder);
 }
 
-static void hsw_crt_pre_enable(struct intel_encoder *encoder)
-{
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-
-	WARN(I915_READ(SPLL_CTL) & SPLL_PLL_ENABLE, "SPLL already enabled\n");
-	I915_WRITE(SPLL_CTL,
-		   SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz | SPLL_PLL_SSC);
-	POSTING_READ(SPLL_CTL);
-	udelay(20);
-}
-
 /* Note: The caller is required to filter out dpms modes not supported by the
  * platform. */
 static void intel_crt_set_dpms(struct intel_encoder *encoder, int mode)
@@ -216,19 +204,6 @@ static void pch_post_disable_crt(struct intel_encoder *encoder)
 	intel_disable_crt(encoder);
 }
 
-static void hsw_crt_post_disable(struct intel_encoder *encoder)
-{
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	uint32_t val;
-
-	DRM_DEBUG_KMS("Disabling SPLL\n");
-	val = I915_READ(SPLL_CTL);
-	WARN_ON(!(val & SPLL_PLL_ENABLE));
-	I915_WRITE(SPLL_CTL, val & ~SPLL_PLL_ENABLE);
-	POSTING_READ(SPLL_CTL);
-}
-
 static void intel_enable_crt(struct intel_encoder *encoder)
 {
 	struct intel_crt *crt = intel_encoder_to_crt(encoder);
@@ -280,6 +255,8 @@ static bool intel_crt_compute_config(struct intel_encoder *encoder,
 	if (HAS_DDI(dev)) {
 		pipe_config->ddi_pll_sel = PORT_CLK_SEL_SPLL;
 		pipe_config->port_clock = 135000 * 2;
+		pipe_config->dpll_hw_state.wrpll =
+			SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz | SPLL_PLL_SSC;
 	}
 
 	return true;
@@ -861,8 +838,6 @@ void intel_crt_init(struct drm_device *dev)
 	if (HAS_DDI(dev)) {
 		crt->base.get_config = hsw_crt_get_config;
 		crt->base.get_hw_state = intel_ddi_get_hw_state;
-		crt->base.pre_enable = hsw_crt_pre_enable;
-		crt->base.post_disable = hsw_crt_post_disable;
 	} else {
 		crt->base.get_config = intel_crt_get_config;
 		crt->base.get_hw_state = intel_crt_get_hw_state;
drivers/gpu/drm/i915/intel_ddi.c +38 -9

86 lines not on this page · raw message

drivers/gpu/drm/i915/intel_display.c +7 -2
index ca9278be49f7..582360d2fa08 100644
@@ -4208,6 +4208,7 @@ struct intel_shared_dpll *intel_get_shared_dpll(struct intel_crtc *crtc,
 	struct intel_shared_dpll *pll;
 	struct intel_shared_dpll_config *shared_dpll;
 	enum intel_dpll_id i;
+	int max = dev_priv->num_shared_dpll;
 
 	shared_dpll = intel_atomic_get_shared_dpll_state(crtc_state->base.state);
 
@@ -4242,9 +4243,11 @@ struct intel_shared_dpll *intel_get_shared_dpll(struct intel_crtc *crtc,
 		WARN_ON(shared_dpll[i].crtc_mask);
 
 		goto found;
-	}
+	} else if (INTEL_INFO(dev_priv)->gen < 9 && HAS_DDI(dev_priv))
+		/* Do not consider SPLL */
+		max = 2;
 
-	for (i = 0; i < dev_priv->num_shared_dpll; i++) {
+	for (i = 0; i < max; i++) {
 		pll = &dev_priv->shared_dplls[i];
 
 		/* Only want to check enabled timings first */
@@ -9696,6 +9699,8 @@ static void haswell_get_ddi_pll(struct drm_i915_private *dev_priv,
 	case PORT_CLK_SEL_WRPLL2:
 		pipe_config->shared_dpll = DPLL_ID_WRPLL2;
 		break;
+	case PORT_CLK_SEL_SPLL:
+		pipe_config->shared_dpll = DPLL_ID_SPLL;
 	}
 }
 

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#1 lore raw
Quoted 8 lines · Maarten Lankhorst

When diagnosing a unrelated bug for someone on irc, it would seem the hardware can be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.

Right now this is not handled well in i915, and it calculates the crtc needs to be reprogrammed on the first modeset without SSC, but the SPLL itself was kept active. Fix this by exposing SPLL as a shared pll that will not be returned by intel_get_shared_dpll; you have to know it exists to use it. ;-)

Quoted 5 lines
Cc Emil Renner Berthing <[email protected]>

---
RFC because I haven't tested it with VGA, but it seems to work according to fix the problem mentioned above.

lgtm and gets rid of some of the fdi vs. normal ddi special-casing, which is nice (since that's a problem for bxt dsi too). I'll pick this up as soon as you managed to run this on some hsw (since we inject a fake vga screen for igt tests you don't even need a real screen). -Daniel

Quoted 208 lines
drivers/gpu/drm/i915/i915_drv.h +2 -0
index 81adf89b92f1..cacdac67d9ba 100644
@@ -345,6 +345,8 @@ enum intel_dpll_id {
 	/* hsw/bdw */
 	DPLL_ID_WRPLL1 = 0,
 	DPLL_ID_WRPLL2 = 1,
+	DPLL_ID_SPLL = 2,
+
 	/* skl */
 	DPLL_ID_SKL_DPLL1 = 0,
 	DPLL_ID_SKL_DPLL2 = 1,
drivers/gpu/drm/i915/intel_crt.c +2 -27
index af5e43bef4a4..592d8fe9f991 100644
@@ -138,18 +138,6 @@ static void hsw_crt_get_config(struct intel_encoder *encoder,
 	pipe_config->base.adjusted_mode.flags |= intel_crt_get_flags(encoder);
 }
 
-static void hsw_crt_pre_enable(struct intel_encoder *encoder)
-{
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-
-	WARN(I915_READ(SPLL_CTL) & SPLL_PLL_ENABLE, "SPLL already enabled\n");
-	I915_WRITE(SPLL_CTL,
-		   SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz | SPLL_PLL_SSC);
-	POSTING_READ(SPLL_CTL);
-	udelay(20);
-}
-
 /* Note: The caller is required to filter out dpms modes not supported by the
  * platform. */
 static void intel_crt_set_dpms(struct intel_encoder *encoder, int mode)
@@ -216,19 +204,6 @@ static void pch_post_disable_crt(struct intel_encoder *encoder)
 	intel_disable_crt(encoder);
 }
 
-static void hsw_crt_post_disable(struct intel_encoder *encoder)
-{
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	uint32_t val;
-
-	DRM_DEBUG_KMS("Disabling SPLL\n");
-	val = I915_READ(SPLL_CTL);
-	WARN_ON(!(val & SPLL_PLL_ENABLE));
-	I915_WRITE(SPLL_CTL, val & ~SPLL_PLL_ENABLE);
-	POSTING_READ(SPLL_CTL);
-}
-
 static void intel_enable_crt(struct intel_encoder *encoder)
 {
 	struct intel_crt *crt = intel_encoder_to_crt(encoder);
@@ -280,6 +255,8 @@ static bool intel_crt_compute_config(struct intel_encoder *encoder,
 	if (HAS_DDI(dev)) {
 		pipe_config->ddi_pll_sel = PORT_CLK_SEL_SPLL;
 		pipe_config->port_clock = 135000 * 2;
+		pipe_config->dpll_hw_state.wrpll =
+			SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz | SPLL_PLL_SSC;
 	}
 
 	return true;
@@ -861,8 +838,6 @@ void intel_crt_init(struct drm_device *dev)
 	if (HAS_DDI(dev)) {
 		crt->base.get_config = hsw_crt_get_config;
 		crt->base.get_hw_state = intel_ddi_get_hw_state;
-		crt->base.pre_enable = hsw_crt_pre_enable;
-		crt->base.post_disable = hsw_crt_post_disable;
 	} else {
 		crt->base.get_config = intel_crt_get_config;
 		crt->base.get_hw_state = intel_crt_get_hw_state;
drivers/gpu/drm/i915/intel_ddi.c +38 -9
index 61575f67a626..dabd903147fa 100644
@@ -1269,6 +1269,18 @@ hsw_ddi_pll_select(struct intel_crtc *intel_crtc,
 		}
 
 		crtc_state->ddi_pll_sel = PORT_CLK_SEL_WRPLL(pll->id);
+	} else if (crtc_state->ddi_pll_sel == PORT_CLK_SEL_SPLL) {
+		struct drm_atomic_state *state = crtc_state->base.state;
+		struct intel_shared_dpll_config *spll =
+			&intel_atomic_get_shared_dpll_state(state)[DPLL_ID_SPLL];
+
+		if (spll->crtc_mask &&
+		    WARN_ON(spll->hw_state.wrpll != crtc_state->dpll_hw_state.wrpll))
+			return false;
+
+		crtc_state->shared_dpll = DPLL_ID_SPLL;
+		spll->hw_state.wrpll = crtc_state->dpll_hw_state.wrpll;
+		spll->crtc_mask |= 1 << intel_crtc->pipe;
 	}
 
 	return true;
@@ -2414,19 +2426,31 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder)
 static void hsw_ddi_pll_enable(struct drm_i915_private *dev_priv,
 			       struct intel_shared_dpll *pll)
 {
-	I915_WRITE(WRPLL_CTL(pll->id), pll->config.hw_state.wrpll);
-	POSTING_READ(WRPLL_CTL(pll->id));
+	uint32_t reg;
+
+	if (pll->id == DPLL_ID_SPLL)
+		reg = SPLL_CTL;
+	else
+		reg = WRPLL_CTL(pll->id);
+
+	I915_WRITE(reg, pll->config.hw_state.wrpll);
+	POSTING_READ(reg);
 	udelay(20);
 }
 
 static void hsw_ddi_pll_disable(struct drm_i915_private *dev_priv,
 				struct intel_shared_dpll *pll)
 {
-	uint32_t val;
+	uint32_t reg, val;
 
-	val = I915_READ(WRPLL_CTL(pll->id));
-	I915_WRITE(WRPLL_CTL(pll->id), val & ~WRPLL_PLL_ENABLE);
-	POSTING_READ(WRPLL_CTL(pll->id));
+	if (pll->id == DPLL_ID_SPLL)
+		reg = SPLL_CTL;
+	else
+		reg = WRPLL_CTL(pll->id);
+
+	val = I915_READ(reg);
+	I915_WRITE(reg, val & ~WRPLL_PLL_ENABLE);
+	POSTING_READ(reg);
 }
 
 static bool hsw_ddi_pll_get_hw_state(struct drm_i915_private *dev_priv,
@@ -2438,23 +2462,28 @@ static bool hsw_ddi_pll_get_hw_state(struct drm_i915_private *dev_priv,
 	if (!intel_display_power_is_enabled(dev_priv, POWER_DOMAIN_PLLS))
 		return false;
 
-	val = I915_READ(WRPLL_CTL(pll->id));
-	hw_state->wrpll = val;
+	if (pll->id == DPLL_ID_SPLL)
+		val = I915_READ(SPLL_CTL);
+	else
+		val = I915_READ(WRPLL_CTL(pll->id));
 
+	hw_state->wrpll = val;
 	return val & WRPLL_PLL_ENABLE;
 }
 
 static const char * const hsw_ddi_pll_names[] = {
 	"WRPLL 1",
 	"WRPLL 2",
+	"SPLL"
 };
 
 static void hsw_shared_dplls_init(struct drm_i915_private *dev_priv)
 {
 	int i;
 
-	dev_priv->num_shared_dpll = 2;
+	dev_priv->num_shared_dpll = 3;
 
+	/* SPLL is special, but needs to be initialized anyway.. */
 	for (i = 0; i < dev_priv->num_shared_dpll; i++) {
 		dev_priv->shared_dplls[i].id = i;
 		dev_priv->shared_dplls[i].name = hsw_ddi_pll_names[i];
drivers/gpu/drm/i915/intel_display.c +7 -2
index ca9278be49f7..582360d2fa08 100644
@@ -4208,6 +4208,7 @@ struct intel_shared_dpll *intel_get_shared_dpll(struct intel_crtc *crtc,
 	struct intel_shared_dpll *pll;
 	struct intel_shared_dpll_config *shared_dpll;
 	enum intel_dpll_id i;
+	int max = dev_priv->num_shared_dpll;
 
 	shared_dpll = intel_atomic_get_shared_dpll_state(crtc_state->base.state);
 
@@ -4242,9 +4243,11 @@ struct intel_shared_dpll *intel_get_shared_dpll(struct intel_crtc *crtc,
 		WARN_ON(shared_dpll[i].crtc_mask);
 
 		goto found;
-	}
+	} else if (INTEL_INFO(dev_priv)->gen < 9 && HAS_DDI(dev_priv))
+		/* Do not consider SPLL */
+		max = 2;
 
-	for (i = 0; i < dev_priv->num_shared_dpll; i++) {
+	for (i = 0; i < max; i++) {
 		pll = &dev_priv->shared_dplls[i];
 
 		/* Only want to check enabled timings first */
@@ -9696,6 +9699,8 @@ static void haswell_get_ddi_pll(struct drm_i915_private *dev_priv,
 	case PORT_CLK_SEL_WRPLL2:
 		pipe_config->shared_dpll = DPLL_ID_WRPLL2;
 		break;
+	case PORT_CLK_SEL_SPLL:
+		pipe_config->shared_dpll = DPLL_ID_SPLL;
 	}
 }
 

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 7 lines
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw

Op 23-09-15 om 14:42 schreef Daniel Vetter:

Quoted 14 lines · Maarten Lankhorst
Quoted 8 lines

When diagnosing a unrelated bug for someone on irc, it would seem the hardware can be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.

Right now this is not handled well in i915, and it calculates the crtc needs to be reprogrammed on the first modeset without SSC, but the SPLL itself was kept active. Fix this by exposing SPLL as a shared pll that will not be returned by intel_get_shared_dpll; you have to know it exists to use it. ;-)

Quoted 5 lines
Cc Emil Renner Berthing <[email protected]>

---
RFC because I haven't tested it with VGA, but it seems to work according to fix the problem mentioned above.

Quoted 5 lines

lgtm and gets rid of some of the fdi vs. normal ddi special-casing, which is nice (since that's a problem for bxt dsi too). I'll pick this up as soon as you managed to run this on some hsw (since we inject a fake vga screen for igt tests you don't even need a real screen).

Emil, do you have a haswell and if so can you test with intel-gpu-tools? kms_pipe_crc_basic and see if it works correctly.
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#3 lore raw
Quoted 15 lines · Maarten Lankhorst

Op 23-09-15 om 14:42 schreef Daniel Vetter:

Quoted 14 lines · Maarten Lankhorst
Quoted 13 lines

When diagnosing a unrelated bug for someone on irc, it would seem the hardware can be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.

Right now this is not handled well in i915, and it calculates the crtc needs to be reprogrammed on the first modeset without SSC, but the SPLL itself was kept active. Fix this by exposing SPLL as a shared pll that will not be returned by intel_get_shared_dpll; you have to know it exists to use it. ;-)

Cc Emil Renner Berthing <[email protected]>

---
RFC because I haven't tested it with VGA, but it seems to work according to fix the problem mentioned above.

Quoted 6 lines
Quoted 5 lines

lgtm and gets rid of some of the fdi vs. normal ddi special-casing, which is nice (since that's a problem for bxt dsi too). I'll pick this up as soon as you managed to run this on some hsw (since we inject a fake vga screen for igt tests you don't even need a real screen).

Emil, do you have a haswell and if so can you test with intel-gpu-tools? kms_pipe_crc_basic and see if it works correctly.

Yeah, I just tested this on my Thinkpad X1 Carbon 2nd gen. with 00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 0b).

It works fine.

--
Emil

IGT-Version: 1.12-ga167042 (x86_64) (Linux: 4.3.0.rc2-2-knud x86_64) Subtest bad-pipe: SUCCESS (0.000s)
Subtest bad-source: SUCCESS (0.000s)
Subtest bad-nb-words-1: SUCCESS (0.000s)
Subtest bad-nb-words-3: SUCCESS (0.000s)
read-crc-pipe-A: Testing connector eDP-1 using pipe A
read-crc-pipe-A: Testing connector DP-1 using pipe A
read-crc-pipe-A: Testing connector HDMI-A-2 using pipe A Subtest read-crc-pipe-A: SUCCESS (6.541s) read-crc-pipe-A-frame-sequence: Testing connector eDP-1 using pipe A read-crc-pipe-A-frame-sequence: Testing connector DP-1 using pipe A read-crc-pipe-A-frame-sequence: Testing connector HDMI-A-2 using pipe A Subtest read-crc-pipe-A-frame-sequence: SUCCESS (6.764s)
rtcwake: assuming RTC uses UTC ...
rtcwake: wakeup from "mem" using /dev/rtc0 at Wed Sep 23 15:29:01 2015
suspend-read-crc-pipe-A: Testing connector eDP-1 using pipe A
suspend-read-crc-pipe-A: Testing connector DP-1 using pipe A
suspend-read-crc-pipe-A: Testing connector HDMI-A-2 using pipe A Subtest suspend-read-crc-pipe-A: SUCCESS (9.309s)
hang-read-crc-pipe-A: Testing connector eDP-1 using pipe A
hang-read-crc-pipe-A: Testing connector DP-1 using pipe A
hang-read-crc-pipe-A: Testing connector HDMI-A-2 using pipe A Subtest hang-read-crc-pipe-A: SUCCESS (13.283s)
read-crc-pipe-B: Testing connector eDP-1 using pipe B
read-crc-pipe-B: Testing connector DP-1 using pipe B
read-crc-pipe-B: Testing connector HDMI-A-2 using pipe B Subtest read-crc-pipe-B: SUCCESS (3.866s) read-crc-pipe-B-frame-sequence: Testing connector eDP-1 using pipe B read-crc-pipe-B-frame-sequence: Testing connector DP-1 using pipe B read-crc-pipe-B-frame-sequence: Testing connector HDMI-A-2 using pipe B Subtest read-crc-pipe-B-frame-sequence: SUCCESS (3.878s)
rtcwake: assuming RTC uses UTC ...
rtcwake: wakeup from "mem" using /dev/rtc0 at Wed Sep 23 15:30:02 2015
suspend-read-crc-pipe-B: Testing connector eDP-1 using pipe B
suspend-read-crc-pipe-B: Testing connector DP-1 using pipe B
suspend-read-crc-pipe-B: Testing connector HDMI-A-2 using pipe B Subtest suspend-read-crc-pipe-B: SUCCESS (6.286s)
hang-read-crc-pipe-B: Testing connector eDP-1 using pipe B
hang-read-crc-pipe-B: Testing connector DP-1 using pipe B
hang-read-crc-pipe-B: Testing connector HDMI-A-2 using pipe B Subtest hang-read-crc-pipe-B: SUCCESS (9.961s)
read-crc-pipe-C: Testing connector eDP-1 using pipe C
read-crc-pipe-C: Testing connector DP-1 using pipe C
read-crc-pipe-C: Testing connector HDMI-A-2 using pipe C Subtest read-crc-pipe-C: SUCCESS (3.850s) read-crc-pipe-C-frame-sequence: Testing connector eDP-1 using pipe C read-crc-pipe-C-frame-sequence: Testing connector DP-1 using pipe C read-crc-pipe-C-frame-sequence: Testing connector HDMI-A-2 using pipe C Subtest read-crc-pipe-C-frame-sequence: SUCCESS (3.830s)
rtcwake: assuming RTC uses UTC ...
rtcwake: wakeup from "mem" using /dev/rtc0 at Wed Sep 23 15:30:56 2015
suspend-read-crc-pipe-C: Testing connector eDP-1 using pipe C
suspend-read-crc-pipe-C: Testing connector DP-1 using pipe C
suspend-read-crc-pipe-C: Testing connector HDMI-A-2 using pipe C Subtest suspend-read-crc-pipe-C: SUCCESS (6.503s)
hang-read-crc-pipe-C: Testing connector eDP-1 using pipe C
hang-read-crc-pipe-C: Testing connector DP-1 using pipe C
hang-read-crc-pipe-C: Testing connector HDMI-A-2 using pipe C Subtest hang-read-crc-pipe-C: SUCCESS (9.807s)

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#4 lore raw
In reply to Maarten Lankhorst
Quoted 113 lines · Maarten Lankhorst

When diagnosing a unrelated bug for someone on irc, it would seem the hardware can be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.

Right now this is not handled well in i915, and it calculates the crtc needs to be reprogrammed on the first modeset without SSC, but the SPLL itself was kept active. Fix this by exposing SPLL as a shared pll that will not be returned by intel_get_shared_dpll; you have to know it exists to use it. ;-)

Cc Emil Renner Berthing <[email protected]>

---
RFC because I haven't tested it with VGA, but it seems to work according to fix the problem mentioned above.

drivers/gpu/drm/i915/i915_drv.h +2 -0
index 81adf89b92f1..cacdac67d9ba 100644
@@ -345,6 +345,8 @@ enum intel_dpll_id {
 	/* hsw/bdw */
 	DPLL_ID_WRPLL1 = 0,
 	DPLL_ID_WRPLL2 = 1,
+	DPLL_ID_SPLL = 2,
+
 	/* skl */
 	DPLL_ID_SKL_DPLL1 = 0,
 	DPLL_ID_SKL_DPLL2 = 1,
drivers/gpu/drm/i915/intel_crt.c +2 -27
index af5e43bef4a4..592d8fe9f991 100644
@@ -138,18 +138,6 @@ static void hsw_crt_get_config(struct intel_encoder *encoder,
 	pipe_config->base.adjusted_mode.flags |= intel_crt_get_flags(encoder);
 }
 
-static void hsw_crt_pre_enable(struct intel_encoder *encoder)
-{
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-
-	WARN(I915_READ(SPLL_CTL) & SPLL_PLL_ENABLE, "SPLL already enabled\n");
-	I915_WRITE(SPLL_CTL,
-		   SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz | SPLL_PLL_SSC);
-	POSTING_READ(SPLL_CTL);
-	udelay(20);
-}
-
 /* Note: The caller is required to filter out dpms modes not supported by the
  * platform. */
 static void intel_crt_set_dpms(struct intel_encoder *encoder, int mode)
@@ -216,19 +204,6 @@ static void pch_post_disable_crt(struct intel_encoder *encoder)
 	intel_disable_crt(encoder);
 }
 
-static void hsw_crt_post_disable(struct intel_encoder *encoder)
-{
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	uint32_t val;
-
-	DRM_DEBUG_KMS("Disabling SPLL\n");
-	val = I915_READ(SPLL_CTL);
-	WARN_ON(!(val & SPLL_PLL_ENABLE));
-	I915_WRITE(SPLL_CTL, val & ~SPLL_PLL_ENABLE);
-	POSTING_READ(SPLL_CTL);
-}
-
 static void intel_enable_crt(struct intel_encoder *encoder)
 {
 	struct intel_crt *crt = intel_encoder_to_crt(encoder);
@@ -280,6 +255,8 @@ static bool intel_crt_compute_config(struct intel_encoder *encoder,
 	if (HAS_DDI(dev)) {
 		pipe_config->ddi_pll_sel = PORT_CLK_SEL_SPLL;
 		pipe_config->port_clock = 135000 * 2;
+		pipe_config->dpll_hw_state.wrpll =
+			SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz | SPLL_PLL_SSC;
 	}
 
 	return true;
@@ -861,8 +838,6 @@ void intel_crt_init(struct drm_device *dev)
 	if (HAS_DDI(dev)) {
 		crt->base.get_config = hsw_crt_get_config;
 		crt->base.get_hw_state = intel_ddi_get_hw_state;
-		crt->base.pre_enable = hsw_crt_pre_enable;
-		crt->base.post_disable = hsw_crt_post_disable;
 	} else {
 		crt->base.get_config = intel_crt_get_config;
 		crt->base.get_hw_state = intel_crt_get_hw_state;
drivers/gpu/drm/i915/intel_ddi.c +12 -0
index 61575f67a626..dabd903147fa 100644
@@ -1269,6 +1269,18 @@ hsw_ddi_pll_select(struct intel_crtc *intel_crtc,
 		}
 
 		crtc_state->ddi_pll_sel = PORT_CLK_SEL_WRPLL(pll->id);
+	} else if (crtc_state->ddi_pll_sel == PORT_CLK_SEL_SPLL) {
+		struct drm_atomic_state *state = crtc_state->base.state;
+		struct intel_shared_dpll_config *spll =
+			&intel_atomic_get_shared_dpll_state(state)[DPLL_ID_SPLL];
+
+		if (spll->crtc_mask &&
+		    WARN_ON(spll->hw_state.wrpll != crtc_state->dpll_hw_state.wrpll))
+			return false;
+
+		crtc_state->shared_dpll = DPLL_ID_SPLL;
+		spll->hw_state.wrpll = crtc_state->dpll_hw_state.wrpll;
+		spll->crtc_mask |= 1 << intel_crtc->pipe;
 	}
 
 	return true;
@@ -2414,19 +2426,31 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder)
 static void hsw_ddi_pll_enable(struct drm_i915_private *dev_priv,

drivers/gpu/drm/i915/intel_ddi.c static void intel_disable_ddi(struct intel_encoder *intel_encoder) · line 2434

Quoted 10 lines
drivers/gpu/drm/i915/intel_ddi.c +6 -2
 			       struct intel_shared_dpll *pll)
 {
-	I915_WRITE(WRPLL_CTL(pll->id), pll->config.hw_state.wrpll);
-	POSTING_READ(WRPLL_CTL(pll->id));
+	uint32_t reg;
+
+	if (pll->id == DPLL_ID_SPLL)
+		reg = SPLL_CTL;
+	else
+		reg = WRPLL_CTL(pll->id);

This is a bit ugly, and reusing hw_sate.wrpll is also a bit fragile due to the overlaps. I think it'd be better to add hw_state.spll (including hw state cross-checking) and specialising the enable/disable/get_hw_state functions.

With that this is Reviewed-by: Daniel Vetter <[email protected]>

Quoted 98 lines
drivers/gpu/drm/i915/intel_ddi.c +20 -7
+
+	I915_WRITE(reg, pll->config.hw_state.wrpll);
+	POSTING_READ(reg);
 	udelay(20);
 }
 
 static void hsw_ddi_pll_disable(struct drm_i915_private *dev_priv,
 				struct intel_shared_dpll *pll)
 {
-	uint32_t val;
+	uint32_t reg, val;
 
-	val = I915_READ(WRPLL_CTL(pll->id));
-	I915_WRITE(WRPLL_CTL(pll->id), val & ~WRPLL_PLL_ENABLE);
-	POSTING_READ(WRPLL_CTL(pll->id));
+	if (pll->id == DPLL_ID_SPLL)
+		reg = SPLL_CTL;
+	else
+		reg = WRPLL_CTL(pll->id);
+
+	val = I915_READ(reg);
+	I915_WRITE(reg, val & ~WRPLL_PLL_ENABLE);
+	POSTING_READ(reg);
 }
 
 static bool hsw_ddi_pll_get_hw_state(struct drm_i915_private *dev_priv,
@@ -2438,23 +2462,28 @@ static bool hsw_ddi_pll_get_hw_state(struct drm_i915_private *dev_priv,
 	if (!intel_display_power_is_enabled(dev_priv, POWER_DOMAIN_PLLS))
 		return false;
 
-	val = I915_READ(WRPLL_CTL(pll->id));
-	hw_state->wrpll = val;
+	if (pll->id == DPLL_ID_SPLL)
+		val = I915_READ(SPLL_CTL);
+	else
+		val = I915_READ(WRPLL_CTL(pll->id));
 
+	hw_state->wrpll = val;
 	return val & WRPLL_PLL_ENABLE;
 }
 
 static const char * const hsw_ddi_pll_names[] = {
 	"WRPLL 1",
 	"WRPLL 2",
+	"SPLL"
 };
 
 static void hsw_shared_dplls_init(struct drm_i915_private *dev_priv)
 {
 	int i;
 
-	dev_priv->num_shared_dpll = 2;
+	dev_priv->num_shared_dpll = 3;
 
+	/* SPLL is special, but needs to be initialized anyway.. */
 	for (i = 0; i < dev_priv->num_shared_dpll; i++) {
 		dev_priv->shared_dplls[i].id = i;
 		dev_priv->shared_dplls[i].name = hsw_ddi_pll_names[i];
drivers/gpu/drm/i915/intel_display.c +7 -2
index ca9278be49f7..582360d2fa08 100644
@@ -4208,6 +4208,7 @@ struct intel_shared_dpll *intel_get_shared_dpll(struct intel_crtc *crtc,
 	struct intel_shared_dpll *pll;
 	struct intel_shared_dpll_config *shared_dpll;
 	enum intel_dpll_id i;
+	int max = dev_priv->num_shared_dpll;
 
 	shared_dpll = intel_atomic_get_shared_dpll_state(crtc_state->base.state);
 
@@ -4242,9 +4243,11 @@ struct intel_shared_dpll *intel_get_shared_dpll(struct intel_crtc *crtc,
 		WARN_ON(shared_dpll[i].crtc_mask);
 
 		goto found;
-	}
+	} else if (INTEL_INFO(dev_priv)->gen < 9 && HAS_DDI(dev_priv))
+		/* Do not consider SPLL */
+		max = 2;
 
-	for (i = 0; i < dev_priv->num_shared_dpll; i++) {
+	for (i = 0; i < max; i++) {
 		pll = &dev_priv->shared_dplls[i];
 
 		/* Only want to check enabled timings first */
@@ -9696,6 +9699,8 @@ static void haswell_get_ddi_pll(struct drm_i915_private *dev_priv,
 	case PORT_CLK_SEL_WRPLL2:
 		pipe_config->shared_dpll = DPLL_ID_WRPLL2;
 		break;
+	case PORT_CLK_SEL_SPLL:
+		pipe_config->shared_dpll = DPLL_ID_SPLL;
 	}
 }
 

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 7 lines
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
maintainer
#5 lore raw
Quoted 130 lines · Daniel Vetter
Quoted 113 lines · Maarten Lankhorst

When diagnosing a unrelated bug for someone on irc, it would seem the hardware can be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.

Right now this is not handled well in i915, and it calculates the crtc needs to be reprogrammed on the first modeset without SSC, but the SPLL itself was kept active. Fix this by exposing SPLL as a shared pll that will not be returned by intel_get_shared_dpll; you have to know it exists to use it. ;-)

Cc Emil Renner Berthing <[email protected]>

---
RFC because I haven't tested it with VGA, but it seems to work according to fix the problem mentioned above.

drivers/gpu/drm/i915/i915_drv.h +2 -0
index 81adf89b92f1..cacdac67d9ba 100644
@@ -345,6 +345,8 @@ enum intel_dpll_id {
 	/* hsw/bdw */
 	DPLL_ID_WRPLL1 = 0,
 	DPLL_ID_WRPLL2 = 1,
+	DPLL_ID_SPLL = 2,
+
 	/* skl */
 	DPLL_ID_SKL_DPLL1 = 0,
 	DPLL_ID_SKL_DPLL2 = 1,
drivers/gpu/drm/i915/intel_crt.c +2 -27
index af5e43bef4a4..592d8fe9f991 100644
@@ -138,18 +138,6 @@ static void hsw_crt_get_config(struct intel_encoder *encoder,
 	pipe_config->base.adjusted_mode.flags |= intel_crt_get_flags(encoder);
 }
 
-static void hsw_crt_pre_enable(struct intel_encoder *encoder)
-{
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-
-	WARN(I915_READ(SPLL_CTL) & SPLL_PLL_ENABLE, "SPLL already enabled\n");
-	I915_WRITE(SPLL_CTL,
-		   SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz | SPLL_PLL_SSC);
-	POSTING_READ(SPLL_CTL);
-	udelay(20);
-}
-
 /* Note: The caller is required to filter out dpms modes not supported by the
  * platform. */
 static void intel_crt_set_dpms(struct intel_encoder *encoder, int mode)
@@ -216,19 +204,6 @@ static void pch_post_disable_crt(struct intel_encoder *encoder)
 	intel_disable_crt(encoder);
 }
 
-static void hsw_crt_post_disable(struct intel_encoder *encoder)
-{
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	uint32_t val;
-
-	DRM_DEBUG_KMS("Disabling SPLL\n");
-	val = I915_READ(SPLL_CTL);
-	WARN_ON(!(val & SPLL_PLL_ENABLE));
-	I915_WRITE(SPLL_CTL, val & ~SPLL_PLL_ENABLE);
-	POSTING_READ(SPLL_CTL);
-}
-
 static void intel_enable_crt(struct intel_encoder *encoder)
 {
 	struct intel_crt *crt = intel_encoder_to_crt(encoder);
@@ -280,6 +255,8 @@ static bool intel_crt_compute_config(struct intel_encoder *encoder,
 	if (HAS_DDI(dev)) {
 		pipe_config->ddi_pll_sel = PORT_CLK_SEL_SPLL;
 		pipe_config->port_clock = 135000 * 2;
+		pipe_config->dpll_hw_state.wrpll =
+			SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz | SPLL_PLL_SSC;
 	}
 
 	return true;
@@ -861,8 +838,6 @@ void intel_crt_init(struct drm_device *dev)
 	if (HAS_DDI(dev)) {
 		crt->base.get_config = hsw_crt_get_config;
 		crt->base.get_hw_state = intel_ddi_get_hw_state;
-		crt->base.pre_enable = hsw_crt_pre_enable;
-		crt->base.post_disable = hsw_crt_post_disable;
 	} else {
 		crt->base.get_config = intel_crt_get_config;
 		crt->base.get_hw_state = intel_crt_get_hw_state;
drivers/gpu/drm/i915/intel_ddi.c +12 -0
index 61575f67a626..dabd903147fa 100644
@@ -1269,6 +1269,18 @@ hsw_ddi_pll_select(struct intel_crtc *intel_crtc,
 		}
 
 		crtc_state->ddi_pll_sel = PORT_CLK_SEL_WRPLL(pll->id);
+	} else if (crtc_state->ddi_pll_sel == PORT_CLK_SEL_SPLL) {
+		struct drm_atomic_state *state = crtc_state->base.state;
+		struct intel_shared_dpll_config *spll =
+			&intel_atomic_get_shared_dpll_state(state)[DPLL_ID_SPLL];
+
+		if (spll->crtc_mask &&
+		    WARN_ON(spll->hw_state.wrpll != crtc_state->dpll_hw_state.wrpll))
+			return false;
+
+		crtc_state->shared_dpll = DPLL_ID_SPLL;
+		spll->hw_state.wrpll = crtc_state->dpll_hw_state.wrpll;
+		spll->crtc_mask |= 1 << intel_crtc->pipe;
 	}
 
 	return true;
@@ -2414,19 +2426,31 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder)
 static void hsw_ddi_pll_enable(struct drm_i915_private *dev_priv,

drivers/gpu/drm/i915/intel_ddi.c static void intel_disable_ddi(struct intel_encoder *intel_encoder) · line 2434

Quoted 10 lines
drivers/gpu/drm/i915/intel_ddi.c +6 -2
 			       struct intel_shared_dpll *pll)
 {
-	I915_WRITE(WRPLL_CTL(pll->id), pll->config.hw_state.wrpll);
-	POSTING_READ(WRPLL_CTL(pll->id));
+	uint32_t reg;
+
+	if (pll->id == DPLL_ID_SPLL)
+		reg = SPLL_CTL;
+	else
+		reg = WRPLL_CTL(pll->id);

This is a bit ugly, and reusing hw_sate.wrpll is also a bit fragile due to the overlaps. I think it'd be better to add hw_state.spll (including hw state cross-checking) and specialising the enable/disable/get_hw_state functions.

Quoted 1 line

With that this is Reviewed-by: Daniel Vetter <[email protected]>

Maarten, please update the patch according to Daniel's comments, as this fixes [1].

BR,
Jani.

[1] http://mid.gmane.org/[email protected]

Quoted 108 lines
Quoted 99 lines
drivers/gpu/drm/i915/intel_ddi.c +20 -7
+
+	I915_WRITE(reg, pll->config.hw_state.wrpll);
+	POSTING_READ(reg);
 	udelay(20);
 }
 
 static void hsw_ddi_pll_disable(struct drm_i915_private *dev_priv,
 				struct intel_shared_dpll *pll)
 {
-	uint32_t val;
+	uint32_t reg, val;
 
-	val = I915_READ(WRPLL_CTL(pll->id));
-	I915_WRITE(WRPLL_CTL(pll->id), val & ~WRPLL_PLL_ENABLE);
-	POSTING_READ(WRPLL_CTL(pll->id));
+	if (pll->id == DPLL_ID_SPLL)
+		reg = SPLL_CTL;
+	else
+		reg = WRPLL_CTL(pll->id);
+
+	val = I915_READ(reg);
+	I915_WRITE(reg, val & ~WRPLL_PLL_ENABLE);
+	POSTING_READ(reg);
 }
 
 static bool hsw_ddi_pll_get_hw_state(struct drm_i915_private *dev_priv,
@@ -2438,23 +2462,28 @@ static bool hsw_ddi_pll_get_hw_state(struct drm_i915_private *dev_priv,
 	if (!intel_display_power_is_enabled(dev_priv, POWER_DOMAIN_PLLS))
 		return false;
 
-	val = I915_READ(WRPLL_CTL(pll->id));
-	hw_state->wrpll = val;
+	if (pll->id == DPLL_ID_SPLL)
+		val = I915_READ(SPLL_CTL);
+	else
+		val = I915_READ(WRPLL_CTL(pll->id));
 
+	hw_state->wrpll = val;
 	return val & WRPLL_PLL_ENABLE;
 }
 
 static const char * const hsw_ddi_pll_names[] = {
 	"WRPLL 1",
 	"WRPLL 2",
+	"SPLL"
 };
 
 static void hsw_shared_dplls_init(struct drm_i915_private *dev_priv)
 {
 	int i;
 
-	dev_priv->num_shared_dpll = 2;
+	dev_priv->num_shared_dpll = 3;
 
+	/* SPLL is special, but needs to be initialized anyway.. */
 	for (i = 0; i < dev_priv->num_shared_dpll; i++) {
 		dev_priv->shared_dplls[i].id = i;
 		dev_priv->shared_dplls[i].name = hsw_ddi_pll_names[i];
drivers/gpu/drm/i915/intel_display.c +7 -2
index ca9278be49f7..582360d2fa08 100644
@@ -4208,6 +4208,7 @@ struct intel_shared_dpll *intel_get_shared_dpll(struct intel_crtc *crtc,
 	struct intel_shared_dpll *pll;
 	struct intel_shared_dpll_config *shared_dpll;
 	enum intel_dpll_id i;
+	int max = dev_priv->num_shared_dpll;
 
 	shared_dpll = intel_atomic_get_shared_dpll_state(crtc_state->base.state);
 
@@ -4242,9 +4243,11 @@ struct intel_shared_dpll *intel_get_shared_dpll(struct intel_crtc *crtc,
 		WARN_ON(shared_dpll[i].crtc_mask);
 
 		goto found;
-	}
+	} else if (INTEL_INFO(dev_priv)->gen < 9 && HAS_DDI(dev_priv))
+		/* Do not consider SPLL */
+		max = 2;
 
-	for (i = 0; i < dev_priv->num_shared_dpll; i++) {
+	for (i = 0; i < max; i++) {
 		pll = &dev_priv->shared_dplls[i];
 
 		/* Only want to check enabled timings first */
@@ -9696,6 +9699,8 @@ static void haswell_get_ddi_pll(struct drm_i915_private *dev_priv,
 	case PORT_CLK_SEL_WRPLL2:
 		pipe_config->shared_dpll = DPLL_ID_WRPLL2;
 		break;
+	case PORT_CLK_SEL_SPLL:
+		pipe_config->shared_dpll = DPLL_ID_SPLL;
 	}
 }
 

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 7 lines
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx