rfi: stmmac: creating an of mdio bus for attached dsa
Subsystems (2)
G'day All,
Prior to submitting a patch I'd just like to get an idea on what the correct way is to create and register an mdio bus for use by the marvell dsa driver. On our system the cpu ethernet port is connected directly to a switch with a fixed link (1Gbit).
So the driver needs to create and persist the mdio bus for the dsa driver using of_mdiobus_register.
The trunk stmmac driver currently doesn't create the mdio bus if a fixed link is found.stmmac_probe_config_dt does hte following check.
if (plat->phy_node || plat->phy_bus_name)
plat->mdio_bus_data = NULL;phy_node is set because a fixed-link is found above and setting mdio_bus_data to null skips mdio bus creation. removing the phy_node check gets things working.
I've also modified stmmac_mdio_register to use of_mdiobus_register and setup the dt to probe for a phy (that doesn't really exist, the switch is on the mdio). This cause a fair bit of log spamming but does seem to work as the switch is detected.
eg: eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
Currently if no phy is found the mdio bus gets de registered so this seems to be required.
In summary what is the correct way to make sure the mdio bus stays registered when a fixed-link is in use? Am I configuring the link to the switch incorrectly?
Phil
+Andrew,
Quoted 12 lines · Phil Reid
G'day All,
Prior to submitting a patch I'd just like to get an idea on what the correct way is to create and register an mdio bus for use by the marvell dsa driver.
On our system the cpu ethernet port is connected directly to a switch with a fixed link (1Gbit).
So the driver needs to create and persist the mdio bus for the dsa driver usingof_mdiobus_register.
The trunk stmmac driver currently doesn't create the mdio bus if a fixed link is found.stmmac_probe_config_dtdoes hte following check.
Quoted 5 lines
if (plat->phy_node || plat->phy_bus_name) plat->mdio_bus_data = NULL;
phy_nodeis set because a fixed-link is found above and settingmdio_bus_datato null skips mdio bus creation. removing thephy_nodecheck gets things working.
It seems to me like you should have the stmmac driver always register its MDIO bus driver, whether or not it will end-up being used depends on the information provided via OF/platform_data.
Even in topologies where a stmmac block is unused, you would expect power/clock gating to be applied for the Ethernet MAC, but still have the ability to use the MDIO bus of this stmmac instance if it connects to a particular device. In your case, I would assume that the stmmac Ethernet MAC and MDIO will be used, so this make even more sense.
Quoted 10 lines
I've also modified
stmmac_mdio_registerto useof_mdiobus_registerand setup the dt to probe for a phy (that doesn't really exist, the switch is on the mdio).
This cause a fair bit of log spamming but does seem to work as the switch is detected.
eg: eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b) Currently if no phy is found the mdio bus gets de registered so this seems to be required.
Quoted 3 lines
In summary what is the correct way to make sure the mdio bus stays registered when a fixed-link is in use?
Am I configuring the link to the switch incorrectly?
This seems reasonable to me. One of the problems with DSA right now is that you need to provide a fixed-link emulated PHY for your Ethernet MAC controller to keep "working" (that is: get link status/parameters etc.), while the switch sits on the MDIO bus and does not look like (yet) a PHY device.
The "problem" here is that the STMMAC driver treats fixed link as there is no MDIO device connected here, so why bother with registering a MDIO bus driver in the first place, which is a valid design shortcut, but not in the case of DSA right now.
In the future, I hope we can have DSA switch devices look like almost regular PHY devices, such that we do not have to use the fixed PHY to keep having the Ethernet MAC controller be happy with link parameters to/from the switch, see [1].
[1]: https://lwn.net/Articles/643149/
Signature · 1 line
Florian