xfstests, bad generic tests 009 and 308
Hi all,
working on arm (32bit arch), kernel 4.1.6.
Looking to find the reason of some bad results on xfstests,
-tests/generic/009
------------------
i get several "all holes" messages
generic/009 [ 842.949643] run fstests generic/009 at 2015-09-18 15:29:36
- output mismatch (see/home/angelo/xfstests/results//generic/009.out.bad)
--- tests/generic/009.out 2015-09-17 10:54:06.689071257 +0000
+++ /home/angelo/xfstests/results//generic/009.out.bad 2015-09-18
15:29:41.412784177 +0000
@@ -1,79 +1,45 @@
QA output created by 009
1. into a hole
-0: [0..7]: hole
-1: [8..23]: unwritten
-2: [24..39]: hole
+0: [0..39]: hole
daa100df6e6711906b61c9ab5aa16032also some other tests are giving the same bad notices.
-tests/generic/308
------------------
I have now: CONFIG_LBDAF=y
In my target device this test creates a 16 Terabytes file 308.tempfile
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
While "df" is not complaining about:
/dev/mmcblk0p5 8378368 45252 8333116 1% /media/p5
and next rm -f on it hands the cpu to 95%, forever.
This issue seems known from a long time, as it has been discussed in the thread:
http://oss.sgi.com/archives/xfs/2013-04/msg00273.html
I was wondering if there was any special reason why the Jeff patch has never been finally applied.
I applied this patch anyway, and tests pass.
Signature · 7 lines
Best regards, Angelo Dureghello _______________________________________________ xfs mailing list [email protected] http://oss.sgi.com/mailman/listinfo/xfs
Quoted 3 lines · Angelo Dureghello
Hi all,
working on arm (32bit arch), kernel 4.1.6.
Is this a new platform?
Also, we need to know what compiler you are using, because we know that certain versions of gcc miscompile XFS kernel code on arm (4.6, 4.7 and certain versions of 4.8 are suspect) due to a combination of compiler mis-optimisations and kernel bugs in the arm 64 bit division asm implementation.
As such, it would be worthwhile trying gcc-4.9 and a 4.3-rc1 kernel to see if the problems still occur.
Quoted 22 lines
Looking to find the reason of some bad results on xfstests,
-tests/generic/009
------------------
i get several "all holes" messagesgeneric/009 [ 842.949643] run fstests generic/009 at 2015-09-18
15:29:36
- output mismatch (see/home/angelo/xfstests/results//generic/009.out.bad)--- tests/generic/009.out 2015-09-17 10:54:06.689071257 +0000 +++ /home/angelo/xfstests/results//generic/009.out.bad 2015-09-18 15:29:41.412784177 +0000 @@ -1,79 +1,45 @@ QA output created by 009 1. into a hole -0: [0..7]: hole -1: [8..23]: unwritten -2: [24..39]: hole +0: [0..39]: hole daa100df6e6711906b61c9ab5aa16032
Quoted 1 line
also some other tests are giving the same bad notices.
Can you attach the entire /home/angelo/xfstests/results//generic/009.out.bad file? I'm not sure which of the tests this output comes from, so I need to confirm which specific operations are resulting in errors.
Quoted 15 lines
-tests/generic/308
------------------I have now:
CONFIG_LBDAF=yIn my target device this test creates a 16 Terabytes file 308.tempfile
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
While "df" is not complaining about:
/dev/mmcblk0p58378368 45252 8333116 1% /media/p5and next rm -f on it hands the cpu to 95%, forever.
Quoted 7 lines
This issue seems known from a long time, as it has been discussed in the thread:
http://oss.sgi.com/archives/xfs/2013-04/msg00273.html
I was wondering if there was any special reason why the Jeff patch has never been finally applied.
MAX_LFS_FILESIZE on 32 bits is 8TB, whereas xfs supports 16TB file size on 32 bit systems. The specific issue this test fixed was committed in commit 8695d27 ("xfs: fix infinite loop at xfs_vm_writepage on 32bit system")
http://oss.sgi.com/archives/xfs/2014-05/msg00447.html
And, as you may notice now, generic/308 is the test case for the exact problem the above commit fixed.
Can you find out exactly where the CPU is looping? sysrq-l will help, as will running 'perf top -U -g' to show you the hot code paths, and so on.
Cheers,
Dave.
Signature · 7 lines
Dave Chinner [email protected] _______________________________________________ xfs mailing list [email protected] http://oss.sgi.com/mailman/listinfo/xfs
Hi Dave,
many thanks for the support. Sorry for the double mail, after first registering mails was not accepted, so i re-registered with a company mail.
Quoted 6 lines · Dave Chinner
Quoted 3 lines · Angelo Dureghello
Hi all,
working on arm (32bit arch), kernel 4.1.6.
Is this a new platform?
Quoted 8 lines
Also, we need to know what compiler you are using, because we know that certain versions of gcc miscompile XFS kernel code on arm (4.6, 4.7 and certain versions of 4.8 are suspect) due to a combination of compiler mis-optimisations and kernel bugs in the arm 64 bit division asm implementation.
As such, it would be worthwhile trying gcc-4.9 and a 4.3-rc1 kernel to see if the problems still occur.
I am using actually gcc-linaro-4.9-2015.05-x86_64_arm-linux-gnueabihf
Quoted 22 lines
Quoted 22 lines
Looking to find the reason of some bad results on xfstests,
-tests/generic/009
------------------
i get several "all holes" messagesgeneric/009 [ 842.949643] run fstests generic/009 at 2015-09-18
15:29:36
- output mismatch (see/home/angelo/xfstests/results//generic/009.out.bad)--- tests/generic/009.out 2015-09-17 10:54:06.689071257 +0000 +++ /home/angelo/xfstests/results//generic/009.out.bad 2015-09-18 15:29:41.412784177 +0000 @@ -1,79 +1,45 @@ QA output created by 009 1. into a hole -0: [0..7]: hole -1: [8..23]: unwritten -2: [24..39]: hole +0: [0..39]: hole daa100df6e6711906b61c9ab5aa16032
Quoted 5 lines
Quoted 1 line
also some other tests are giving the same bad notices.
Can you attach the entire
/home/angelo/xfstests/results//generic/009.out.badfile? I'm not sure which of the tests this output comes from, so I need to confirm which specific operations are resulting in errors.
Sure, i completed the whole generic + shared + xfs tests.
In total i have 38 errors. And trying now one by one to understand the reason. I attached the 009 output.
Quoted 27 lines
Quoted 15 lines
-tests/generic/308
------------------I have now:
CONFIG_LBDAF=yIn my target device this test creates a 16 Terabytes file 308.tempfile
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
While "df" is not complaining about:
/dev/mmcblk0p58378368 45252 8333116 1% /media/p5and next rm -f on it hands the cpu to 95%, forever.
Quoted 7 lines
This issue seems known from a long time, as it has been discussed in the thread:
http://oss.sgi.com/archives/xfs/2013-04/msg00273.html
I was wondering if there was any special reason why the Jeff patch has never been finally applied.
MAX_LFS_FILESIZEon 32 bits is 8TB, whereas xfs supports 16TB file size on 32 bit systems. The specific issue this test fixed was committed in commit 8695d27 ("xfs: fix infinite loop atxfs_vm_writepageon 32bit system")
Quoted 4 lines
http://oss.sgi.com/archives/xfs/2014-05/msg00447.html
And, as you may notice now, generic/308 is the test case for the exact problem the above commit fixed.
I have recent git version of xfstests, but generic/308 shows
#! /bin/bash
# FS QA Test No. 308
#
# Regression test for commit:
# f17722f ext4: Fix max file size and logical block counting of extent format file
Quoted 3 lines
Can you find out exactly where the CPU is looping? sysrq-l will help, as will running 'perf top -U -g' to show you the hot code paths, and so on.
Strangely, the patch http://oss.sgi.com/archives/xfs/2014-05/msg00447.html is already included in the xfs that comes with this 4.1.6 kernel, while only applying previous
http://oss.sgi.com/archives/xfs/2013-04/msg00273.html patch from Jeff fix the issue and test 308 get passed.
I have a 16MB partition, and wondering why xfs allows from test 308 to create a 16TB file.
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
When at 308 test exit, rm is invoked, system get blocked in infinite loop.
root 5445 0.7 0.2 3760 3180 ttyS0 S+ 10:53 0:00 /bin/bash /home/angelo/xfstests/tests/generic/308 root 5674 100 0.0 1388 848 ttyS0 R+ 10:53 0:27 rm -f /media/p5/testfile.308
Can't install actually perf-tools for some debian repos issue, but let me know, i will enable sysrq if needed.
Best regards
Angelo
Quoted 4 lines
Cheers,
Dave.
Signature · 2 lines
Best regards, Angelo Dureghello
QA output created by 009
1. into a hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
2. into allocated spacecc58a7417c2d7763adc45b6fcd3fa024
3. into unwritten spacedaa100df6e6711906b61c9ab5aa16032
4. hole -> data
0: [0..39]: holecc63069677939f69a6e8f68cae6a6dac
5. hole -> unwritten
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
6. data -> hole
0: [24..39]: hole1b3779878366498b28c702ef88c4a773
7. data -> unwritten
0: [32..39]: hole1b3779878366498b28c702ef88c4a773
8. unwritten -> hole
0: [24..39]: holedaa100df6e6711906b61c9ab5aa16032
9. unwritten -> data
0: [32..39]: holecc63069677939f69a6e8f68cae6a6dac
10. hole -> data -> hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
11. data -> hole -> dataf6aeca13ec49e5b266cd1c913cd726e3
12. unwritten -> data -> unwrittendaa100df6e6711906b61c9ab5aa16032
13. data -> unwritten -> dataf6aeca13ec49e5b266cd1c913cd726e3
14. data -> hole @ EOFe1f024eedd27ea6b1c3e9b841c850404
15. data -> hole @ 0eecb7aa303d121835de05028751d301c
16. data -> cache cold ->holeeecb7aa303d121835de05028751d301c
17. data -> hole in single block file
0000000 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
0000200 0000 0000 0000 0000 0000 0000 0000 0000
*
0000400 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
1. into a hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
2. into allocated spacecc58a7417c2d7763adc45b6fcd3fa024
3. into unwritten spacedaa100df6e6711906b61c9ab5aa16032
4. hole -> data
0: [0..39]: holecc63069677939f69a6e8f68cae6a6dac
5. hole -> unwritten
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
6. data -> hole
0: [24..39]: hole1b3779878366498b28c702ef88c4a773
7. data -> unwritten
0: [32..39]: hole1b3779878366498b28c702ef88c4a773
8. unwritten -> hole
0: [24..39]: holedaa100df6e6711906b61c9ab5aa16032
9. unwritten -> data
0: [32..39]: holecc63069677939f69a6e8f68cae6a6dac
10. hole -> data -> hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
11. data -> hole -> dataf6aeca13ec49e5b266cd1c913cd726e3
12. unwritten -> data -> unwrittendaa100df6e6711906b61c9ab5aa16032
13. data -> unwritten -> dataf6aeca13ec49e5b266cd1c913cd726e3
14. data -> hole @ EOFe1f024eedd27ea6b1c3e9b841c850404
15. data -> hole @ 0eecb7aa303d121835de05028751d301c
16. data -> cache cold ->holeeecb7aa303d121835de05028751d301c
17. data -> hole in single block file
0000000 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
0000200 0000 0000 0000 0000 0000 0000 0000 0000
*
0000400 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
1. into a hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
2. into allocated spacecc58a7417c2d7763adc45b6fcd3fa024
3. into unwritten spacecc58a7417c2d7763adc45b6fcd3fa024
4. hole -> datacc58a7417c2d7763adc45b6fcd3fa024
5. hole -> unwrittencc58a7417c2d7763adc45b6fcd3fa024
6. data -> holecc58a7417c2d7763adc45b6fcd3fa024
7. data -> unwrittencc58a7417c2d7763adc45b6fcd3fa024
8. unwritten -> holecc58a7417c2d7763adc45b6fcd3fa024
9. unwritten -> datacc58a7417c2d7763adc45b6fcd3fa024
10. hole -> data -> holef6aeca13ec49e5b266cd1c913cd726e3
11. data -> hole -> dataf6aeca13ec49e5b266cd1c913cd726e3
12. unwritten -> data -> unwrittenf6aeca13ec49e5b266cd1c913cd726e3
13. data -> unwritten -> dataf6aeca13ec49e5b266cd1c913cd726e3
14. data -> hole @ EOFe1f024eedd27ea6b1c3e9b841c850404
15. data -> hole @ 0eecb7aa303d121835de05028751d301c
16. data -> cache cold ->holeeecb7aa303d121835de05028751d301c
17. data -> hole in single block file
0000000 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
0000200 0000 0000 0000 0000 0000 0000 0000 0000
*
0000400 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
1. into a hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
2. into allocated spacecc58a7417c2d7763adc45b6fcd3fa024
3. into unwritten spacecc58a7417c2d7763adc45b6fcd3fa024
4. hole -> datacc58a7417c2d7763adc45b6fcd3fa024
5. hole -> unwrittencc58a7417c2d7763adc45b6fcd3fa024
6. data -> holecc58a7417c2d7763adc45b6fcd3fa024
7. data -> unwrittencc58a7417c2d7763adc45b6fcd3fa024
8. unwritten -> holecc58a7417c2d7763adc45b6fcd3fa024
9. unwritten -> datacc58a7417c2d7763adc45b6fcd3fa024
10. hole -> data -> holef6aeca13ec49e5b266cd1c913cd726e3
11. data -> hole -> dataf6aeca13ec49e5b266cd1c913cd726e3
12. unwritten -> data -> unwrittenf6aeca13ec49e5b266cd1c913cd726e3
13. data -> unwritten -> dataf6aeca13ec49e5b266cd1c913cd726e3
14. data -> hole @ EOFe1f024eedd27ea6b1c3e9b841c850404
15. data -> hole @ 0eecb7aa303d121835de05028751d301c
16. data -> cache cold ->holeeecb7aa303d121835de05028751d301c
17. data -> hole in single block file
0000000 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
0000200 0000 0000 0000 0000 0000 0000 0000 0000
*
0000400 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs
Sry, in my previous mail please s/16M/16G. Was a typo.
I am using an SD card with test partitions 8G and 16G.
Best regards
Angelo
Quoted 135 lines · Angelo Dureghello
Hi Dave,
many thanks for the support. Sorry for the double mail, after first registering mails was not accepted, so i re-registered with a company mail.
Quoted 6 lines · Dave Chinner
Quoted 3 lines · Angelo Dureghello
Hi all,
working on arm (32bit arch), kernel 4.1.6.
Is this a new platform?
Quoted 8 lines
Also, we need to know what compiler you are using, because we know that certain versions of gcc miscompile XFS kernel code on arm (4.6, 4.7 and certain versions of 4.8 are suspect) due to a combination of compiler mis-optimisations and kernel bugs in the arm 64 bit division asm implementation.
As such, it would be worthwhile trying gcc-4.9 and a 4.3-rc1 kernel to see if the problems still occur.
I am using actually gcc-linaro-4.9-2015.05-x86_64_arm-linux-gnueabihf
Quoted 22 lines
Quoted 22 lines
Looking to find the reason of some bad results on xfstests,
-tests/generic/009
------------------
i get several "all holes" messagesgeneric/009 [ 842.949643] run fstests generic/009 at 2015-09-18
15:29:36
- output mismatch (see/home/angelo/xfstests/results//generic/009.out.bad)--- tests/generic/009.out 2015-09-17 10:54:06.689071257 +0000 +++ /home/angelo/xfstests/results//generic/009.out.bad 2015-09-18 15:29:41.412784177 +0000 @@ -1,79 +1,45 @@ QA output created by 009 1. into a hole -0: [0..7]: hole -1: [8..23]: unwritten -2: [24..39]: hole +0: [0..39]: hole daa100df6e6711906b61c9ab5aa16032Quoted 5 lines
Quoted 1 line
also some other tests are giving the same bad notices.
Can you attach the entire
/home/angelo/xfstests/results//generic/009.out.badfile? I'm not sure which of the tests this output comes from, so I need to confirm which specific operations are resulting in errors.Sure, i completed the whole generic + shared + xfs tests.
In total i have 38 errors. And trying now one by one to understand the reason. I attached the 009 output.Quoted 27 lines
Quoted 15 lines
-tests/generic/308
------------------I have now:
CONFIG_LBDAF=yIn my target device this test creates a 16 Terabytes file 308.tempfile
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
While "df" is not complaining about:
/dev/mmcblk0p58378368 45252 8333116 1% /media/p5and next rm -f on it hands the cpu to 95%, forever.
Quoted 7 lines
This issue seems known from a long time, as it has been discussed in the thread:
http://oss.sgi.com/archives/xfs/2013-04/msg00273.html
I was wondering if there was any special reason why the Jeff patch has never been finally applied.
MAX_LFS_FILESIZEon 32 bits is 8TB, whereas xfs supports 16TB file size on 32 bit systems. The specific issue this test fixed was committed in commit 8695d27 ("xfs: fix infinite loop atxfs_vm_writepageon 32bit system")Quoted 4 lines
http://oss.sgi.com/archives/xfs/2014-05/msg00447.html
And, as you may notice now, generic/308 is the test case for the exact problem the above commit fixed.
I have recent git version of xfstests, but generic/308 shows
#!
/bin/bash
# FS QA Test No. 308
#
# Regression test for commit:# f17722f ext4: Fix max file size and logical block counting of extent format fileQuoted 3 lines
Can you find out exactly where the CPU is looping? sysrq-l will help, as will running 'perf top -U -g' to show you the hot code paths, and so on.
Strangely, the patch http://oss.sgi.com/archives/xfs/2014-05/msg00447.html is already included in the xfs that comes with this 4.1.6 kernel, while only applying previous
http://oss.sgi.com/archives/xfs/2013-04/msg00273.html patch from Jeff fix the issue and test 308 get passed.
I have a 16MB partition, and wondering why xfs allows from test 308 to create a 16TB file.
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
When at 308 test exit, rm is invoked, system get blocked in infinite loop.
root 5445 0.7 0.2 3760 3180 ttyS0 S+ 10:53 0:00 /bin/bash /home/angelo/xfstests/tests/generic/308 root 5674 100 0.0 1388 848 ttyS0 R+ 10:53 0:27 rm -f /media/p5/testfile.308Can't install actually perf-tools for some debian repos issue, but let me know, i will enable sysrq if needed.
Best regards
AngeloQuoted 4 lines
Cheers,
Dave.
_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs
Signature · 7 lines
Best regards, Angelo Dureghello _______________________________________________ xfs mailing list [email protected] http://oss.sgi.com/mailman/listinfo/xfs
Quoted 20 lines · Angelo Dureghello
Hi Dave,
many thanks for the support. Sorry for the double mail, after first registering mails was not accepted, so i re-registered with a company mail.
Quoted 12 lines · Dave Chinner
Quoted 3 lines · Angelo Dureghello
Hi all,
working on arm (32bit arch), kernel 4.1.6.
Is this a new platform?
Also, we need to know what compiler you are using, because we know that certain versions of gcc miscompile XFS kernel code on arm (4.6, 4.7 and certain versions of 4.8 are suspect) due to a combination of compiler mis-optimisations and kernel bugs in the arm 64 bit division asm implementation.
Quoted 4 lines
Quoted 2 lines
As such, it would be worthwhile trying gcc-4.9 and a 4.3-rc1 kernel to see if the problems still occur.
I am using actually gcc-linaro-4.9-2015.05-x86_64_arm-linux-gnueabihf
So gcc-4.9 patched with a bunch of stuff from linaro and built as a cross compiler from x86-64 to 32 bit arm? ISTR we had a bunch of different compiler problems at one point that only showed up in kernels build with a x86-64 to arm cross-compiler. In case you haven't guessed, XFS has a history of being bitten by ARM compiler problems. There's been a lot more problems in the past couple of years than the historical trend, though.
As it is, I highly recommend that you try a current 4.3 kernel, as there are several code fixes in the XFS kernel code that work around compiler issues we know about. AFAIA, the do_div() asm bug that trips recent gcc optimisations isn't in the upstream kernel yet, but that can be worked around by setting CONFIG_CC_OPTIMIZE_FOR_SIZE=y in your build.
Quoted 28 lines
Quoted 16 lines
Quoted 16 lines
generic/009 [ 842.949643] run fstests generic/009 at 2015-09-18
15:29:36
- output mismatch (see/home/angelo/xfstests/results//generic/009.out.bad)--- tests/generic/009.out 2015-09-17 10:54:06.689071257 +0000 +++ /home/angelo/xfstests/results//generic/009.out.bad 2015-09-18 15:29:41.412784177 +0000 @@ -1,79 +1,45 @@ QA output created by 009 1. into a hole -0: [0..7]: hole -1: [8..23]: unwritten -2: [24..39]: hole +0: [0..39]: hole daa100df6e6711906b61c9ab5aa16032Quoted 5 lines
Quoted 1 line
also some other tests are giving the same bad notices.
Can you attach the entire
/home/angelo/xfstests/results//generic/009.out.badfile? I'm not sure which of the tests this output comes from, so I need to confirm which specific operations are resulting in errors.Sure, i completed the whole generic + shared + xfs tests. In total i have 38 errors. And trying now one by one to understand the reason.
I attached the 009 output.Quoted 2 lines
Quoted 2 lines
-tests/generic/308
------------------
....
Quoted 8 lines
I have recent git version of xfstests, but generic/308 shows
#!
/bin/bash
# FS QA Test No. 308
#
# Regression test for commit:# f17722f ext4: Fix max file size and logical block counting of extent format file
More that one filesystem had problems with maximum file sizes on 32 bit systems. Compare the contents of the test; don't stop reading because the summary of the test makes you think the rest of the test is unrelated to the problem at hand.
Quoted 4 lines
I have a 16MB partition, and wondering why xfs allows from test 308 to create a 16TB file.
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
https://en.wikipedia.org/wiki/Sparse_file
Quoted 8 lines
QA output created by 009
1. into a hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
2. into allocated spacecc58a7417c2d7763adc45b6fcd3fa024
3. into unwritten spacedaa100df6e6711906b61c9ab5aa16032
I don't need to look any further to see that something is badly wrong here. This is telling me that no extents are being allocated at all, which indicates either fiemap is broken, awk/sed is broken or misbehaving (and hence mangling the output) or something deep in the filesystem code is fundamentally broken in some strange, silent way.
Can you create an xfs filesystem on your scratch device, and manually run this command and post the output:
# mkfs.xfs -V # mkfs.xfs <dev> # mount <dev> /mnt/xfs # xfs_io -f -c "pwrite 0 64k" -c sync \ -c "bmap -vp" -c "fiemap -v" \ -c "falloc 1024k 256k" -c sync \ -c "pwrite 1088k 64k" -c sync \ -c "bmap -vp" -c "fiemap -v" \ /mnt/xfs/testfile
and attach the entire output?
It would also be good if you can run this command under trace-cmd and capture all the XFS events that occur during the test. See
http://xfs.org/index.php/XFS_FAQ#Q:_What_information_should_I_include_when_reporting_a_problem.3F
for details, and attach the (compressed) report file.
Cheers,
Dave.
Signature · 7 lines
Dave Chinner [email protected] _______________________________________________ xfs mailing list [email protected] http://oss.sgi.com/mailman/listinfo/xfs
Hi Dave,
still thanks for following.
Quoted 9 lines
Quoted 1 line
I am using actually gcc-linaro-4.9-2015.05-x86_64_arm-linux-gnueabihf
So gcc-4.9 patched with a bunch of stuff from linaro and built as a cross compiler from x86-64 to 32 bit arm? ISTR we had a bunch of different compiler problems at one point that only showed up in kernels build with a x86-64 to arm cross-compiler. In case you haven't guessed, XFS has a history of being bitten by ARM compiler problems. There's been a lot more problems in the past couple of years than the historical trend, though.
Quoted 6 lines
As it is, I highly recommend that you try a current 4.3 kernel, as there are several code fixes in the XFS kernel code that work around compiler issues we know about. AFAIA, the
do_div()asm bug that trips recent gcc optimisations isn't in the upstream kernel yet, but that can be worked around by settingCONFIG_CC_OPTIMIZE_FOR_SIZE=yin your build.
Well, i updated to this toolchain recently, but built the kernel also with an i686 4.9 toolchain, and had exactly same tests errors. Yes i am always cross compiling for armhf btw.
I am using a 4.1.5-rt from TI,
will try possibly some more recent version and let you know.
Quoted 47 lines
Quoted 8 lines
I have recent git version of xfstests, but generic/308 shows
#!
/bin/bash
# FS QA Test No. 308
#
# Regression test for commit:# f17722f ext4: Fix max file size and logical block counting of extent format fileMore that one filesystem had problems with maximum file sizes on 32 bit systems. Compare the contents of the test; don't stop reading because the summary of the test makes you think the rest of the test is unrelated to the problem at hand.
Quoted 4 lines
I have a 16MB partition, and wondering why xfs allows from test 308 to create a 16TB file.
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
https://en.wikipedia.org/wiki/Sparse_file
Quoted 8 lines
QA output created by 009
1. into a hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
2. into allocated spacecc58a7417c2d7763adc45b6fcd3fa024
3. into unwritten spacedaa100df6e6711906b61c9ab5aa16032I don't need to look any further to see that something is badly wrong here. This is telling me that no extents are being allocated at all, which indicates either fiemap is broken, awk/sed is broken or misbehaving (and hence mangling the output) or something deep in the filesystem code is fundamentally broken in some strange, silent way.
Can you create an xfs filesystem on your scratch device, and manually run this command and post the output:
# mkfs.xfs -V # mkfs.xfs <dev> # mount <dev> /mnt/xfs # xfs_io -f -c "pwrite 0 64k" -c sync \ -c "bmap -vp" -c "fiemap -v" \ -c "falloc 1024k 256k" -c sync \ -c "pwrite 1088k 64k" -c sync \ -c "bmap -vp" -c "fiemap -v" \ /mnt/xfs/testfile
Quoted 1 line
and attach the entire output?
I attached the output. I can be completely wrong, but file system seems quite reliable for rootfs operations until now. At least, never had any issue after installing and removing several and several debian packages.
Only issues i had are created from test 308 that, if left running too long, it damages the fs.
Quoted 2 lines
It would also be good if you can run this command under trace-cmd and capture all the XFS events that occur during the test. See
Ok, about test 308, the 2 xfs_io operations passes, it stops on the rm exiting the tests, while trying to erase the 16t file.
# Create a sparse file with an extent lays at one block before old s_maxbytes offset=$(((2**32 - 2) * $block_size))
$XFS_IO_PROG -f -c "pwrite $offset $block_size" -c fsync $testfile >$seqres.full 2>&1
rm can remove remove correctly this file (17592186040320)
# Write to the block after the extent just created
offset=$(((2**32 - 1) * $block_size))
$XFS_IO_PROG -f -c "pwrite $offset $block_size" -c fsync $testfile >>$seqres.full 2>&1
while rm hangs on removing this file (17592186044415)
Magic sysrq l or t is not helping, nothing useful comes out. But i collected the strace log. Since the issue is at unlinkat().
Many thanks
Best regards
Angelo
Signature · 2 lines
Best regards, Angelo Dureghello
root[249] ~
# mkfs.xfs -V
mkfs.xfs version 3.2.1
root[250] ~
# mkfs.xfs /dev/mmcblk0p6
mkfs.xfs: /dev/mmcblk0p6 appears to contain an existing filesystem (xfs).
mkfs.xfs: Use the -f option to force overwrite.
root[251] ~
# mkfs.xfs -f /dev/mmcblk0p6
meta-data=/dev/mmcblk0p6 isize=256 agcount=4, agsize=551008 blks
= sectsz=512 attr=2, projid32bit=1
= crc=0 finobt=0
data = bsize=4096 blocks=2204032, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0 ftype=0
log =internal log bsize=4096 blocks=2560, version=2
= sectsz=512 sunit=0 blks, lazy-count=1
realtime =none extsz=4096 blocks=0, rtextents=0
root[252] ~
# mount /dev/mmcblk0p6 /media/p6
[38946.599770] XFS (mmcblk0p6): Mounting V4 Filesystem
[38946.800708] XFS (mmcblk0p6): Ending clean mount# xfs_io -f -c "pwrite 0 64k" -c sync \
-c "bmap -vp" -c "fiemap -v" \
-c "falloc 1024k 256k" -c sync \
-c "pwrite 1088k 64k" -c sync \
-c "bmap -vp" -c "fiemap -v" \
/media/p6/testfile
wrote 65536/65536 bytes at offset 0
64 KiB, 16 ops; 0.0000 sec (96.154 MiB/sec and 24615.3846 ops/sec)
command "sync" not found
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS
0: [0..127]: 96..223 0 (96..223) 128 00000
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 96..223 128 0x1
command "sync" not found
wrote 65536/65536 bytes at offset 1114112
64 KiB, 16 ops; 0.0000 sec (112.208 MiB/sec and 28725.3142 ops/sec)
command "sync" not found
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS
0: [0..127]: 96..223 0 (96..223) 128 00000
1: [128..2047]: hole 1920
2: [2048..2559]: 2144..2655 0 (2144..2655) 512 10000
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 96..223 128 0x0
1: [128..2047]: hole 1920
2: [2048..2175]: 2144..2271 128 0x800
3: [2176..2303]: 2272..2399 128 0x0
4: [2304..2559]: 2400..2655 256 0x801Step by step xfs_io
-------------------
Due to the "sync" is missing, i tried also command by command with shell "sync" after each command. Output is exactly the same.
-rw------- 1 root root 17592186040320 Sep 22 10:55 testfile.308
rm ok
-rw------- 1 root root 17592186044415 Sep 22 10:58 testfile.308
total 496
drwxr-xr-x 11 root root 4096 Sep 22 10:58 .
drwxr-xr-x 4 root root 101 Sep 22 08:40 .. -rw------- 1 root root 131072 Sep 21 14:50 008.24410 -rw------- 1 root root 131072 Sep 21 14:52 008.2913 -rw------- 1 root root 4096 Sep 21 14:50 009.25001 -rw------- 1 root root 4096 Sep 21 14:52 009.3505 -rw------- 1 root root 81920 Sep 21 14:50 012.26531 -rw------- 1 root root 49152 Sep 21 14:52 012.5039 drwxr-xr-x 3 root root 4096 Sep 21 15:16 14536 drwxr-xr-x 3 root root 38 Sep 21 15:25 16802 drwxr-xr-x 3 root root 4096 Sep 21 15:26 18438 drwxr-xr-x 3 root root 38 Sep 21 15:27 21042 drwxr-xr-x 3 root root 38 Sep 21 14:50 27593 drwxr-xr-x 3 root root 70 Sep 21 15:08 8274 drwxr-xr-x 3 root root 15 Sep 21 14:53 fsstress.5653.1
drwxr-xr-x 22 root root 4096 Sep 21 14:53 fsstress.5653.2
-rw------- 1 root root 17592186044415 Sep 22 11:44 testfile.308
drwxr-xr-x 2 root root 20 Sep 21 15:12 tmp
root[252] vpc24 /media/p5
# rm testfile.308
# strace rm testfile.308
execve("/bin/rm", ["rm", "testfile.308"], [/* 16 vars */]) = 0
brk(0) = 0x2a000
uname({sys="Linux", node="vpc24", ...}) = 0
access("/etc/ld.so.nohwcap", F_OK) = -1 ENOENT (No such file or directory)
mmap2(NULL, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb6f36000
access("/etc/ld.so.preload", R_OK) = -1 ENOENT (No such file or directory)
open("/etc/ld.so.cache", O_RDONLY|O_CLOEXEC) = 3
fstat64(3, {st_mode=S_IFREG|0644, st_size=34089, ...}) = 0
mmap2(NULL, 34089, PROT_READ, MAP_PRIVATE, 3, 0) = 0xb6f2d000
close(3) = 0
access("/etc/ld.so.nohwcap", F_OK) = -1 ENOENT (No such file or directory)
open("/lib/arm-linux-gnueabihf/libc.so.6", O_RDONLY|O_CLOEXEC) = 3
read(3, "\177ELF\1\1\1\3\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0Mw\1\0004\0\0\0"..., 512) = 512
lseek(3, 899996, SEEK_SET) = 899996
read(3, "\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 2880) = 2880
lseek(3, 896548, SEEK_SET) = 896548
read(3, "A4\0\0\0aeabi\0\1*\0\0\0\0057-A\0\6\n\7A\10\1\t\2\n\3\f"..., 53) = 53
fstat64(3, {st_mode=S_IFREG|0755, st_size=902876, ...}) = 0
mmap2(NULL, 972200, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0xb6e23000
mprotect(0xb6efc000, 61440, PROT_NONE) = 0
mmap2(0xb6f0b000, 12288, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0xd8000) = 0xb6f0b000
mmap2(0xb6f0e000, 9640, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0xb6f0e000
close(3) = 0
mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb6f2c000
set_tls(0xb6f2c850, 0xb6f39050, 0xb6f2cf38, 0xb6f2c850, 0xb6f39050) = 0
mprotect(0xb6f0b000, 8192, PROT_READ) = 0
mprotect(0x28000, 4096, PROT_READ) = 0
mprotect(0xb6f38000, 4096, PROT_READ) = 0
munmap(0xb6f2d000, 34089) = 0
brk(0) = 0x2a000
brk(0x4b000) = 0x4b000
ioctl(0, SNDCTL_TMR_TIMEBASE or SNDRV_TIMER_IOCTL_NEXT_DEVICE or TCGETS, {B115200 opost isig icanon echo ...}) = 0
newfstatat(AT_FDCWD, "testfile.308", {st_mode=S_IFREG|0600, st_size=17592186044415, ...}, AT_SYMLINK_NOFOLLOW) = 0
geteuid32() = 0
unlinkat(AT_FDCWD, "testfile.308", 0_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs
Quoted 34 lines · Angelo Dureghello
Quoted 34 lines
Quoted 4 lines
I have a 16MB partition, and wondering why xfs allows from test 308 to create a 16TB file.
-rw------- 1 root root 17592186044415 Sep 18 09:40 testfile.308
https://en.wikipedia.org/wiki/Sparse_file
Quoted 8 lines
QA output created by 009
1. into a hole
0: [0..39]: holedaa100df6e6711906b61c9ab5aa16032
2. into allocated spacecc58a7417c2d7763adc45b6fcd3fa024
3. into unwritten spacedaa100df6e6711906b61c9ab5aa16032I don't need to look any further to see that something is badly wrong here. This is telling me that no extents are being allocated at all, which indicates either fiemap is broken, awk/sed is broken or misbehaving (and hence mangling the output) or something deep in the filesystem code is fundamentally broken in some strange, silent way.
Can you create an xfs filesystem on your scratch device, and manually run this command and post the output:
# mkfs.xfs -V # mkfs.xfs <dev> # mount <dev> /mnt/xfs # xfs_io -f -c "pwrite 0 64k" -c sync \ -c "bmap -vp" -c "fiemap -v" \ -c "falloc 1024k 256k" -c sync \ -c "pwrite 1088k 64k" -c sync \ -c "bmap -vp" -c "fiemap -v" \ /mnt/xfs/testfile
Quoted 3 lines
Quoted 1 line
and attach the entire output?
I attached the output.
Urk, the command should be "fsync", not "sync". Regardless, the last bmap/fiemap pair shows something interesting:
bmap-vp:
Quoted 5 lines
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS 0: [0..127]: 96..223 0 (96..223) 128 00000 1: [128..2047]: hole 1920 2: [2048..2559]: 2144..2655 0 (2144..2655) 512 10000
fiemap -v:
Quoted 7 lines
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..127]: 96..223 128 0x0 1: [128..2047]: hole 1920 2: [2048..2175]: 2144..2271 128 0x800 3: [2176..2303]: 2272..2399 128 0x0 4: [2304..2559]: 2400..2655 256 0x801
Note that they are different - the former shows an unwritten extent of 256k @ offset 1MB, the later shows that extent split by 64k of data @ 1088k.
The bmap -vp output is incorrect - it is supposed to sync data first and so should look the same as the fiemap output. Can you run this test again, this time with s/sync/fsync so the files are clean when bmap/fiemap are run? Can you run it a second time (umount/mkfs again) but with fiemap run first? i.e '-c "fiemap -v" -c "bmap -vp" \' instead of the original order?
Next, can you compile your kernel with CONFIG_XFS_DEBUG=y and rerun the tests? Does anything interesting appear in dmesg during the test run?
Quoted 4 lines
I can be completely wrong, but file system
seems quite reliable for rootfs operations until now. At least, never had any issue after installing and removing several and several debian packages.
right, normal distro operation doesn't use preallocation or hole punching, so you won't have seen issues with that.
Quoted 11 lines
Ok, about test 308, the 2
xfs_iooperations passes, it stops on the rm exiting
the tests, while trying to erase the 16t file.# Create a sparse file with an extent lays at one block before old
s_maxbytes
offset=$(((2**32 - 2) * $block_size))
$XFS_IO_PROG -f -c "pwrite $offset $block_size" -c fsync $testfileQuoted 1 line
$seqres.full 2>&1
rm can remove remove correctly this file (17592186040320)
What is the large number here?
offset: (2**32 - 2) * 4096 = 17592186036224
end file size: (2**32 - 2) * 4096 + 4096 = 17592186040320
So it is the end file size.
Quoted 4 lines
# Write to the block after the extent just created offset=$(((2**32 - 1) * $block_size))
$XFS_IO_PROG -f -c "pwrite $offset $block_size" -c fsync $testfileQuoted 1 line
Quoted 1 line
$seqres.full 2>&1
This should fail with -EFBIG
Quoted 1 line
while rm hangs on removing this file (17592186044415)
offset: (2**32 - 1) * 4096 = 17592186040320
end file size: (2**32 - 1) * 4096 + 4096 = 17592186044416
Hmmm - that file is truncated by one byte. We set sb->s_maxbytes to 17592186044415 in xfs_max_file_offset() on 32 bit systems, so this truncation is expected.
Most definitely need to run this under CONFIG_XFS_DEBUG=y - you should enable this whenever running xfstests to check things are working correctly as it enables all sorts of internal consistency and constraint checking (i.e. checking things that "should never, ever happen" haven't actually occurred).
Quoted 2 lines
Magic sysrq l or t is not helping, nothing useful comes out. But i collected the strace log. Since the issue is at
unlinkat().
Not actually useful - I need to know what is happening inside the unlinkat() call. I'm going to need a trace-cmd event dump of that xfs_io command and the subsequent rm (at least for the first couple of seconds of the rm). Please put the output file from the trace-cmd record command on a tmpfs filesystem so it doesn't pollute the xfs event trace ;)
Cheers,
Dave.
Signature · 7 lines
Dave Chinner [email protected] _______________________________________________ xfs mailing list [email protected] http://oss.sgi.com/mailman/listinfo/xfs
Hi Dave,
many thanks.
Quoted 30 lines · Dave Chinner
Urk, the command should be "fsync", not "sync". Regardless, the last bmap/fiemap pair shows something interesting:
bmap-vp:
Quoted 5 lines
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS 0: [0..127]: 96..223 0 (96..223) 128 00000 1: [128..2047]: hole 1920 2: [2048..2559]: 2144..2655 0 (2144..2655) 512 10000fiemap -v:
Quoted 7 lines
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..127]: 96..223 128 0x0 1: [128..2047]: hole 1920 2: [2048..2175]: 2144..2271 128 0x800 3: [2176..2303]: 2272..2399 128 0x0 4: [2304..2559]: 2400..2655 256 0x801Note that they are different - the former shows an unwritten extent of 256k @ offset 1MB, the later shows that extent split by 64k of data @ 1088k.
The bmap -vp output is incorrect - it is supposed to sync data first and so should look the same as the fiemap output. Can you run this test again, this time with s/sync/fsync so the files are clean when bmap/fiemap are run? Can you run it a second time (umount/mkfs again) but with fiemap run first? i.e '-c "fiemap -v" -c "bmap -vp" \' instead of the original order?
Quoted 3 lines
Next, can you compile your kernel with
CONFIG_XFS_DEBUG=yand rerun the tests? Does anything interesting appear in dmesg during the test run?
Done, see mkfs_output_2.txt attached
Quoted 7 lines
Not actually useful - I need to know what is happening inside the
unlinkat()call. I'm going to need a trace-cmd event dump of thatxfs_iocommand and the subsequent rm (at least for the first couple of seconds of the rm). Please put the output file from the trace-cmd record command on a tmpfs filesystem so it doesn't pollute the xfs event trace ;)
I set some traces inside fs/namei.c do_unlinkat()
root[243] vpc24 (master) /home/angelo/xfstests
# ./start_xfs_test.sh QA output created by 308 [ 144.822616] XFS (mmcblk0p5): Mounting V4 Filesystem [ 145.074537] XFS (mmcblk0p5): Starting recovery (logdev: internal) [ 145.107298] XFS (mmcblk0p5): Ending recovery (logdev: internal) Silence is golden [ 145.413606] do_unlinkat(): entering [ 145.417124] do_unlinkat(): retry [ 145.421156] do_unlinkat(): retry_delegate [ 145.425920] do_unlinkat(): vfs_unlink returns 0 [ 145.430950] do_unlinkat(): exit2
At least that function "seems" to complete, but, as from my previous message looks like strace was not showing nothig over it.
I captured about 10 seconds of events after the "hang" on 308. Hope they are enough.
File is quite long, so you can read it from here:
http://sysam.it/~angelo/events.txt
bye,
Signature · 2 lines
Best regards, Angelo Dureghello
# # xfs_io -f -c "pwrite 0 64k" -c fsync \ -c "bmap -vp" -c "fiemap -v" \ -c "falloc 1024k 256k" -c fsync \ -c "pwrite 1088k 64k" -c fsync \ -c "bmap -vp" -c "fiemap -v" \ /media/p6/testfile
# xfs_io -f -c "pwrite 0 64k" -c fsync \
Quoted 5 lines
-c "bmap -vp" -c "fiemap -v" \
-c "falloc 1024k 256k" -c fsync \
-c "pwrite 1088k 64k" -c fsync \
-c "bmap -vp" -c "fiemap -v" \
/media/p6/testfilewrote 65536/65536 bytes at offset 0
64 KiB, 16 ops; 0.0000 sec (10.271 MiB/sec and 2629.4166 ops/sec) /media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS
0: [0..127]: 96..223 0 (96..223) 128 00000
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 96..223 128 0x1
wrote 65536/65536 bytes at offset 1114112
64 KiB, 16 ops; 0.0000 sec (11.857 MiB/sec and 3035.4771 ops/sec) /media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS 0: [0..127]: 96..223 0 (96..223) 128 00000 1: [128..2047]: hole 1920 2: [2048..2175]: 2144..2271 0 (2144..2271) 128 10000 3: [2176..2303]: 2272..2399 0 (2272..2399) 128 00000 4: [2304..2559]: 2400..2655 0 (2400..2655) 256 10000 /media/p6/testfile: EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..127]: 96..223 128 0x0 1: [128..2047]: hole 1920 2: [2048..2175]: 2144..2271 128 0x800 3: [2176..2303]: 2272..2399 128 0x0 4: [2304..2559]: 2400..2655 256 0x801
root[251] host ~
# mkfs.xfs -f /dev/mmcblk0p6
meta-data=/dev/mmcblk0p6 isize=256 agcount=4, agsize=551008 blks
= sectsz=512 attr=2, projid32bit=1
= crc=0 finobt=0
data = bsize=4096 blocks=2204032, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0 ftype=0
log =internal log bsize=4096 blocks=2560, version=2
= sectsz=512 sunit=0 blks, lazy-count=1
realtime =none extsz=4096 blocks=0, rtextents=0
root[252] host ~
# mount /dev/mmcblk0p6 /media/p6
[ 1000.531021] XFS (mmcblk0p6): Mounting V4 Filesystem
[ 1000.813339] XFS (mmcblk0p6): Ending clean mount
root[253] host ~
# xfs_io -f -c "pwrite 0 64k" -c fsync \Quoted 5 lines
-c "bmap -vp" -c "fiemap -v" \
-c "falloc 1024k 256k" -c fsync \
-c "pwrite 1088k 64k" -c fsync \
-c "fiemap -v" -c "bmap -vp" \
/media/p6/testfilewrote 65536/65536 bytes at offset 0
64 KiB, 16 ops; 0.0000 sec (10.126 MiB/sec and 2592.3526 ops/sec) /media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS
0: [0..127]: 96..223 0 (96..223) 128 00000
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 96..223 128 0x1
wrote 65536/65536 bytes at offset 1114112
64 KiB, 16 ops; 0.0000 sec (11.519 MiB/sec and 2948.7652 ops/sec) /media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..127]: 96..223 128 0x0 1: [128..2047]: hole 1920 2: [2048..2175]: 2144..2271 128 0x800 3: [2176..2303]: 2272..2399 128 0x0 4: [2304..2559]: 2400..2655 256 0x801 /media/p6/testfile: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS 0: [0..127]: 96..223 0 (96..223) 128 00000 1: [128..2047]: hole 1920 2: [2048..2175]: 2144..2271 0 (2144..2271) 128 10000 3: [2176..2303]: 2272..2399 0 (2272..2399) 128 00000 4: [2304..2559]: 2400..2655 0 (2400..2655) 256 10000
root[254] host ~
_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs
Quoted 16 lines · Angelo Dureghello
Hi Dave,
many thanks.
Quoted 11 lines · Dave Chinner
Urk, the command should be "fsync", not "sync". Regardless, the last bmap/fiemap pair shows something interesting:
bmap-vp:
Quoted 5 lines
/media/p6/testfile:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL FLAGS 0: [0..127]: 96..223 0 (96..223) 128 00000 1: [128..2047]: hole 1920 2: [2048..2559]: 2144..2655 0 (2144..2655) 512 10000fiemap -v:
....
Quoted 2 lines
Quoted 2 lines
and so should look the same as the fiemap output. Can you run this test again, this time with s/sync/fsync so the files are clean when
Ok, so a preceding fsync results in bmap displaying all data ranges being written. Hmmm - I'll need to look into that, it's likely not a problem but just a longstanding bmap wart that fiemap doesn't have...
Quoted 3 lines
Quoted 3 lines
Next, can you compile your kernel with
CONFIG_XFS_DEBUG=yand rerun the tests? Does anything interesting appear in dmesg during the test run?
Nothing in dmesg?
Quoted 10 lines
Quoted 7 lines
Not actually useful - I need to know what is happening inside the
unlinkat()call. I'm going to need a trace-cmd event dump of thatxfs_iocommand and the subsequent rm (at least for the first couple of seconds of the rm). Please put the output file from the trace-cmd record command on a tmpfs filesystem so it doesn't pollute the xfs event trace ;)I set some traces inside
fs/namei.cdo_unlinkat()root[243] vpc24 (master)
/home/angelo/xfstests
Quoted 11 lines
# ./start_xfs_test.sh QA output created by 308 [ 144.822616] XFS (mmcblk0p5): Mounting V4 Filesystem [ 145.074537] XFS (mmcblk0p5): Starting recovery (logdev: internal) [ 145.107298] XFS (mmcblk0p5): Ending recovery (logdev: internal) Silence is golden [ 145.413606] do_unlinkat(): entering [ 145.417124] do_unlinkat(): retry [ 145.421156] do_unlinkat(): retry_delegate [ 145.425920] do_unlinkat(): vfs_unlink returns 0 [ 145.430950] do_unlinkat(): exit2
I think you'll find it's the deferred __fput() run from task_work_run() that does all the work of freeing the extents in the file. task_work_run() is executed before the process returns to userspace....
Quoted 7 lines
At least that function "seems" to complete, but, as from my previous message
looks like strace was not showing nothig over it.I captured about 10 seconds of events after the "hang" on 308. Hope they are
enough.
I need to see the events that lead up to the hang, so you need to start tracing before you run the test script, then stop tracing once the hang has occurred. If the trace doesn't have events from the processes the test runs, then you haven't captured the right events...
Cheers,
Dave.
Signature · 7 lines
Dave Chinner [email protected] _______________________________________________ xfs mailing list [email protected] http://oss.sgi.com/mailman/listinfo/xfs
Quoted 1 line · Dave Chinner
As it is, I highly recommend that you try a current 4.3 kernel, as there are several code fixes in the XFS kernel code that work around compiler issues we know about. AFAIA, the
do_div()asm bug that trips recent gcc optimisations isn't in the upstream kernel yet, but that can be worked around by settingCONFIG_CC_OPTIMIZE_FOR_SIZE=yin your build.
Hi dave,
I can confirm that CONFIG_CC_OPTIMIZE_FOR_SIZE=y is (was ?) the only way for me to have reliable XFS kernel code on different arm platforms (Marvell kirkwood, Allwinner A20, Amlogic S805), no matter what recent gcc version I've been using.
I must admit I was cross-compiling from X86-64 too, but I think (not sure) that it was also the case with native gcc.
I must also admit that I didn't tried since some months, because CONFIG_CC_OPTIMIZE_FOR_SIZE=y was the silver bullet for arm xfs kernel crashes. This crash was difficult to understand because it occurs quite randomly (I.e it can take several hours to trigger)
If there's a patch floating around for gcc (or kernel), I'm interested to test.
Cheers,
_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs
Quoted 18 lines · Yann Dupont - Veille Techno
Quoted 6 lines · Dave Chinner
As it is, I highly recommend that you try a current 4.3 kernel, as there are several code fixes in the XFS kernel code that work around compiler issues we know about. AFAIA, the
do_div()asm bug that trips recent gcc optimisations isn't in the upstream kernel yet, but that can be worked around by settingCONFIG_CC_OPTIMIZE_FOR_SIZE=yin your build.Hi dave,
I can confirm that
CONFIG_CC_OPTIMIZE_FOR_SIZE=yis (was ?) the only way for me to have reliable XFS kernel code on different arm platforms (Marvell kirkwood, Allwinner A20, Amlogic S805), no matter what recent gcc version I've been using.I must admit I was cross-compiling from X86-64 too, but I think (not sure) that it was also the case with native gcc.
Quoted 7 lines
I must also admit that I didn't tried since some months, because
CONFIG_CC_OPTIMIZE_FOR_SIZE=ywas the silver bullet for arm xfs kernel crashes. This crash was difficult to understand because it occurs quite randomly (I.e it can take several hours to trigger)If there's a patch floating around for gcc (or kernel), I'm interested to test.
See this subthread from august:
http://oss.sgi.com/archives/xfs/2015-08/msg00234.html
AFAICT, the do_div patch to fix the problem has not yet been picked up - it's not in the 4.3-rc2 kernel...
Cheers,
Dave.
Signature · 7 lines
Dave Chinner [email protected] _______________________________________________ xfs mailing list [email protected] http://oss.sgi.com/mailman/listinfo/xfs
Quoted 23 lines · Dave Chinner
Quoted 22 lines · Yann Dupont - Veille Techno
Quoted 6 lines · Dave Chinner
As it is, I highly recommend that you try a current 4.3 kernel, as there are several code fixes in the XFS kernel code that work around compiler issues we know about. AFAIA, the
do_div()asm bug that trips recent gcc optimisations isn't in the upstream kernel yet, but that can be worked around by settingCONFIG_CC_OPTIMIZE_FOR_SIZE=yin your build.Hi dave,
I can confirm that
CONFIG_CC_OPTIMIZE_FOR_SIZE=yis (was ?) the only way for me to have reliable XFS kernel code on different arm platforms (Marvell kirkwood, Allwinner A20, Amlogic S805), no matter what recent gcc version I've been using.I must admit I was cross-compiling from X86-64 too, but I think (not sure) that it was also the case with native gcc.
I must also admit that I didn't tried since some months, because
CONFIG_CC_OPTIMIZE_FOR_SIZE=ywas the silver bullet for arm xfs kernel crashes. This crash was difficult to understand because it occurs quite randomly (I.e it can take several hours to trigger)
Quoted 5 lines
Quoted 2 lines
If there's a patch floating around for gcc (or kernel), I'm interested to test.
See this subthread from august:
Oh, missed this thread.
Thanks a lot for the pointer, will try this patch ! Cheers,
_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs
Hi Dave and all,
The 99% cpu loop on tests/generic/308 (on "rm") happens also on i686 (32bit), kernel 4.2.0 (gcc 4.9.1)
So, we can exclude it is a cross-compilation issue, or an ARM specific issue. It should just be a 32-bit rch wide related issue.
I hardly found out the reason, at my opinion it doesn't have to be fixed in xfs. I proposed this patch.
http://marc.info/?l=linux-kernel&m=144330858305518&w=2
Let's see if the list reply.
Couldn't proceed still on the other "all hole" errors, will look into that. As far as i know, tests as 009 seems to give same errors to non arm users too.
Will investigate further.
Best regards,
Angelo Dureghello
Quoted 39 lines · Yann Dupont - Veille Techno
Quoted 23 lines · Dave Chinner
Quoted 22 lines · Yann Dupont - Veille Techno
Quoted 6 lines · Dave Chinner
As it is, I highly recommend that you try a current 4.3 kernel, as there are several code fixes in the XFS kernel code that work around compiler issues we know about. AFAIA, the
do_div()asm bug that trips recent gcc optimisations isn't in the upstream kernel yet, but that can be worked around by settingCONFIG_CC_OPTIMIZE_FOR_SIZE=yin your build.Hi dave,
I can confirm that
CONFIG_CC_OPTIMIZE_FOR_SIZE=yis (was ?) the only way for me to have reliable XFS kernel code on different arm platforms (Marvell kirkwood, Allwinner A20, Amlogic S805), no matter what recent gcc version I've been using.I must admit I was cross-compiling from X86-64 too, but I think (not sure) that it was also the case with native gcc.
I must also admit that I didn't tried since some months, because
CONFIG_CC_OPTIMIZE_FOR_SIZE=ywas the silver bullet for arm xfs kernel crashes. This crash was difficult to understand because it occurs quite randomly (I.e it can take several hours to trigger)Quoted 5 lines
Quoted 2 lines
If there's a patch floating around for gcc (or kernel), I'm interested to test.
See this subthread from august:
Oh, missed this thread.
Thanks a lot for the pointer, will try this patch ! Cheers,
_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs
Signature · 2 lines
Best regards, Angelo Dureghello
# cat /sys/kernel/debug/tracing/trace | head -1000
# tracer: function_graph
#
# CPU DURATION FUNCTION CALLS
# | | | | | | |
1) 0.814 us | xfs_file_open();
0) | xfs_xattr_get() {
0) 0.650 us | xfs_attr_get();
0) 5.856 us | }
0) | xfs_file_read_iter() {
0) 1.301 us | xfs_ilock();
0) 1.139 us | xfs_iunlock();
0) + 19.032 us | }
0) | xfs_file_read_iter() {
0) 0.814 us | xfs_ilock();
0) 0.813 us | xfs_iunlock();
0) + 15.942 us | }
0) | xfs_file_read_iter() {
0) 0.488 us | xfs_ilock();
0) 0.813 us | xfs_iunlock();
0) + 12.363 us | }
0) | xfs_vn_follow_link() {
0) | xfs_readlink() {
0) 0.814 us | xfs_ilock();
0) 0.651 us | xfs_iunlock();
0) 9.109 us | }
0) + 14.315 us | }
0) 0.488 us | xfs_file_open();
0) | xfs_file_read_iter() {
0) 0.813 us | xfs_ilock();
0) 0.814 us | xfs_iunlock();
0) + 13.501 us | }
0) | xfs_file_read_iter() {
0) 0.651 us | xfs_ilock();
0) 0.651 us | xfs_iunlock();
0) + 12.200 us | }
0) 0.976 us | xfs_file_mmap();
0) 0.651 us | xfs_file_mmap();
0) | xfs_filemap_fault() {
0) 0.813 us | xfs_ilock();
0) 0.813 us | xfs_iunlock();
0) + 11.550 us | }
0) 0.813 us | xfs_file_mmap();
0) 0.813 us | xfs_file_mmap();
0) | xfs_filemap_fault() {
0) 0.813 us | xfs_ilock();
0) 0.651 us | xfs_iunlock();
0) + 10.410 us | }
0) | xfs_file_release() {
0) | xfs_release() {
0) 0.650 us | xfs_can_free_eofblocks();
0) | xfs_free_eofblocks() {
0) 0.976 us | xfs_ilock();
0) | xfs_bmapi_read() {
0) 0.488 us | xfs_isilocked();
0) | xfs_bmap_search_extents() {
0) | xfs_bmap_search_multi_extents() {
0) | xfs_iext_bno_to_ext() {
0) 0.326 us | xfs_bmbt_get_startoff();
0) 0.650 us | xfs_bmbt_get_blockcount();
0) + 76.291 us | }
0) 0.488 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.488 us | __xfs_bmbt_get_all();
0) 4.067 us | }
0) + 92.070 us | }
0) + 95.648 us | }
0) ! 104.270 us | }
0) 0.650 us | xfs_iunlock();
0) ! 117.608 us | }
0) ! 128.832 us | }
0) ! 132.899 us | }
0) | xfs_file_release() {
0) | xfs_release() {
0) 0.651 us | xfs_can_free_eofblocks();
0) | xfs_free_eofblocks() {
0) 0.976 us | xfs_ilock();
0) | xfs_bmapi_read() {
0) 0.325 us | xfs_isilocked();
0) | xfs_bmap_search_extents() {
0) | xfs_bmap_search_multi_extents() {
0) | xfs_iext_bno_to_ext() {
0) 0.325 us | xfs_bmbt_get_startoff();
0) 0.326 us | xfs_bmbt_get_blockcount();
0) 7.808 us | }
0) 0.488 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.488 us | __xfs_bmbt_get_all();
0) 4.067 us | }
0) + 22.286 us | }
0) + 26.027 us | }
0) + 33.347 us | }
0) 0.651 us | xfs_iunlock();
0) + 49.613 us | }
0) + 60.186 us | }
0) + 64.090 us | }
0) | xfs_file_release() {
0) | xfs_release() {
0) 0.651 us | xfs_can_free_eofblocks();
0) | xfs_free_eofblocks() {
0) 0.650 us | xfs_ilock();
0) | xfs_bmapi_read() {
0) 0.326 us | xfs_isilocked();
0) | xfs_bmap_search_extents() {
0) | xfs_bmap_search_multi_extents() {
0) | xfs_iext_bno_to_ext() {
0) 0.325 us | xfs_bmbt_get_startoff();
0) 0.326 us | xfs_bmbt_get_blockcount();
0) 7.645 us | }
0) 0.325 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.325 us | __xfs_bmbt_get_all();
0) 4.067 us | }
0) + 21.960 us | }
0) + 25.376 us | }
0) + 32.696 us | }
0) 0.650 us | xfs_iunlock();
0) + 44.245 us | }
0) + 54.005 us | }
0) + 57.747 us | }
0) | xfs_file_release() {
0) | xfs_release() {
0) 0.488 us | xfs_can_free_eofblocks();
0) | xfs_free_eofblocks() {
0) 0.813 us | xfs_ilock();
0) | xfs_bmapi_read() {
0) 0.325 us | xfs_isilocked();
0) | xfs_bmap_search_extents() {
0) | xfs_bmap_search_multi_extents() {
0) | xfs_iext_bno_to_ext() {
0) 0.326 us | xfs_bmbt_get_startoff();
0) 0.325 us | xfs_bmbt_get_blockcount();
0) 7.645 us | }
0) 0.488 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.326 us | __xfs_bmbt_get_all();
0) 4.229 us | }
0) + 22.285 us | }
0) + 25.701 us | }
0) + 32.696 us | }
0) 0.651 us | xfs_iunlock();
0) + 44.733 us | }
0) + 54.330 us | }
0) + 57.909 us | }
0) | xfs_file_release() {
0) | xfs_release() {
0) 0.651 us | xfs_can_free_eofblocks();
0) | xfs_free_eofblocks() {
0) 0.650 us | xfs_ilock();
0) | xfs_bmapi_read() {
0) 0.162 us | xfs_isilocked();
0) | xfs_bmap_search_extents() {
0) | xfs_bmap_search_multi_extents() {
0) | xfs_iext_bno_to_ext() {
0) 0.325 us | xfs_bmbt_get_startoff();
0) 0.325 us | xfs_bmbt_get_blockcount();
0) 9.110 us | }
0) 0.326 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.325 us | __xfs_bmbt_get_all();
0) 4.067 us | }
0) + 23.750 us | }
0) + 27.328 us | }
0) + 34.648 us | }
0) 0.651 us | xfs_iunlock();
0) + 46.522 us | }
0) + 56.283 us | }
0) + 59.861 us | }
0) | xfs_file_release() {
0) | xfs_release() {
0) 0.488 us | xfs_can_free_eofblocks();
0) | xfs_free_eofblocks() {
0) 0.814 us | xfs_ilock();
0) | xfs_bmapi_read() {
0) 0.325 us | xfs_isilocked();
0) | xfs_bmap_search_extents() {
0) | xfs_bmap_search_multi_extents() {
0) | xfs_iext_bno_to_ext() {
0) 0.326 us | xfs_bmbt_get_startoff();
0) 0.488 us | xfs_bmbt_get_blockcount();
0) 7.808 us | }
0) 0.325 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.488 us | __xfs_bmbt_get_all();
0) 3.904 us | }
0) + 21.960 us | }
0) + 25.376 us | }
0) + 32.696 us | }
0) 0.651 us | xfs_iunlock();
0) + 44.896 us | }
0) + 54.656 us | }
0) + 58.072 us | }
0) | xfs_file_release() {
0) | xfs_release() {
0) 0.488 us | xfs_can_free_eofblocks();
0) | xfs_free_eofblocks() {
0) 0.651 us | xfs_ilock();
0) | xfs_bmapi_read() {
0) 0.325 us | xfs_isilocked();
0) | xfs_bmap_search_extents() {
0) | xfs_bmap_search_multi_extents() {
0) | xfs_iext_bno_to_ext() {
0) 0.163 us | xfs_bmbt_get_startoff();
0) 0.325 us | xfs_bmbt_get_blockcount();
0) 7.808 us | }
0) 0.325 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.325 us | __xfs_bmbt_get_all();
0) 3.742 us | }
0) + 21.960 us | }
0) + 25.539 us | }
0) + 32.696 us | }
0) 0.651 us | xfs_iunlock();
0) + 44.733 us | }
0) + 54.493 us | }
0) + 57.909 us | }
0) 0.814 us | xfs_file_open();
0) 0.976 us | xfs_vn_getattr();
0) 1.139 us | xfs_file_mmap();
0) | xfs_vn_follow_link() {
0) | xfs_readlink() {
0) 0.651 us | xfs_ilock();
0) 0.650 us | xfs_iunlock();
0) 9.435 us | }
0) + 14.477 us | }
0) 0.651 us | xfs_file_open();
0) | xfs_file_read_iter() {
0) 0.814 us | xfs_ilock();
0) 0.813 us | xfs_iunlock();
0) + 17.731 us | }
0) 1.138 us | xfs_file_llseek();
0) | xfs_file_read_iter() {
0) 0.650 us | xfs_ilock();
0) 0.814 us | xfs_iunlock();
0) + 18.707 us | }
0) 0.488 us | xfs_file_llseek();
0) | xfs_file_read_iter() {
0) 0.651 us | xfs_ilock();
0) 0.650 us | xfs_iunlock();
0) + 12.200 us | }
0) 0.651 us | xfs_vn_getattr();
0) 0.651 us | xfs_file_mmap();
0) 0.976 us | xfs_file_mmap();
0) | xfs_filemap_fault() {
0) 0.813 us | xfs_ilock();
0) 0.650 us | xfs_iunlock();
0) + 10.736 us | }
0) | xfs_file_release() {
0) | xfs_release() {
0) 0.488 us | xfs_can_free_eofblocks();
0) | xfs_free_eofblocks() {
0) 0.813 us | xfs_ilock();
0) | xfs_bmapi_read() {
0) 0.326 us | xfs_isilocked();
0) | xfs_bmap_search_extents() {
0) | xfs_bmap_search_multi_extents() {
0) | xfs_iext_bno_to_ext() {
0) 0.326 us | xfs_bmbt_get_startoff();
0) 0.325 us | xfs_bmbt_get_blockcount();
0) 8.133 us | }
0) 0.325 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.326 us | __xfs_bmbt_get_all();
0) 3.904 us | }
0) + 22.285 us | }
0) + 25.864 us | }
0) + 33.672 us | }
0) 0.650 us | xfs_iunlock();
0) + 46.523 us | }
0) + 57.421 us | }
0) + 61.488 us | }
0) 1.138 us | xfs_vn_getattr();
0) | xfs_vn_unlink() {
0) | xfs_remove() {
0) | xfs_trans_alloc() {
0) 1.464 us | _xfs_trans_alloc();
0) 6.669 us | }
0) | xfs_trans_reserve() {
0) 1.464 us | xfs_mod_fdblocks();
0) | xfs_log_reserve() {
0) 0.650 us | xfs_log_calc_unit_res();
0) + 13.501 us | }
0) + 23.262 us | }
0) 0.976 us | xfs_ilock();
0) | xfs_lock_two_inodes() {
0) 0.651 us | xfs_ilock();
0) 0.976 us | xfs_ilock_nowait();
0) 9.110 us | }
0) 0.326 us | xfs_isilocked();
0) 1.464 us | xfs_trans_add_item();
0) 0.488 us | xfs_isilocked();
0) 1.301 us | xfs_trans_add_item();
0) 0.488 us | xfs_isilocked();
0) 0.163 us | xfs_isilocked();
0) | xfs_droplink() {
0) 0.325 us | xfs_isilocked();
0) 0.326 us | xfs_isilocked();
0) | xfs_iunlink() {
0) | xfs_read_agi() {
0) | xfs_buf_read_map() {
0) | xfs_buf_get_map() {
0) | _xfs_buf_find() {
0) 1.301 us | xfs_perag_get();
0) 0.651 us | xfs_perag_put();
0) 1.302 us | xfs_buf_trylock();
0) + 16.754 us | }
0) + 20.984 us | }
0) + 25.051 us | }
0) 1.301 us | xfs_trans_add_item();
0) + 34.974 us | }
0) + 40.992 us | }
0) + 54.656 us | }
0) | xfs_dir_removename() {
0) | xfs_default_hashname() {
0) 0.325 us | xfs_da_hashname();
0) 4.392 us | }
0) | xfs_dir2_sf_removename() {
0) 0.651 us | xfs_da_compname();
0) | xfs_dir2_sfe_get_ino() {
0) 0.326 us | xfs_dir2_sf_get_ino.isra.8();
0) 4.066 us | }
0) 0.488 us | xfs_dir2_sf_entsize();
0) 0.651 us | xfs_idata_realloc();
0) | xfs_dir2_sf_check.isra.6() {
0) | xfs_dir2_sf_get_parent_ino() {
0) 0.325 us | xfs_dir2_sf_get_ino.isra.8();
0) 3.904 us | }
0) 7.971 us | }
0) 0.326 us | xfs_isilocked();
0) + 36.600 us | }
0) + 53.030 us | }
0) 0.488 us | xfs_bmap_finish();
0) | xfs_trans_commit() {
0) 0.326 us | xfs_isilocked();
0) | xfs_iextents_copy() {
0) 0.488 us | xfs_isilocked();
0) 0.488 us | xfs_bmap_trace_exlist();
0) 0.325 us | xfs_iext_get_ext();
0) 0.488 us | xfs_bmbt_get_startblock();
0) | xfs_validate_extents() {
0) 0.326 us | xfs_iext_get_ext();
0) | xfs_bmbt_get_all() {
0) 0.325 us | __xfs_bmbt_get_all();
0) 3.904 us | }
0) + 11.224 us | }
0) + 30.744 us | }
0) 0.163 us | xfs_isilocked();
0) 0.488 us | xfs_next_bit();
0) 0.326 us | xfs_next_bit();
0) 0.325 us | xfs_next_bit();
0) 0.325 us | xfs_next_bit();
0) 0.488 us | xfs_buf_offset();
0) | xfs_log_done() {
0) 0.488 us | xfs_log_space_wake();
0) 1.302 us | xfs_log_ticket_put();
0) + 12.525 us | }
0) | xfs_trans_unreserve_and_mod_sb() {
0) 1.138 us | xfs_mod_fdblocks();
0) 5.043 us | }
0) | xfs_trans_free_items() {
0) 0.488 us | xfs_isilocked();
0) 1.302 us | xfs_iunlock();
0) 1.302 us | xfs_trans_free_item_desc();
0) 0.488 us | xfs_isilocked();
0) 0.651 us | xfs_iunlock();
0) 1.301 us | xfs_trans_free_item_desc();
0) 1.301 us | xfs_buf_unlock();
0) 0.814 us | xfs_buf_rele();
0) 0.976 us | xfs_trans_free_item_desc();
0) ! 135.176 us | }
0) | xfs_trans_free() {
0) 0.325 us | xfs_extent_busy_clear();
0) 5.694 us | }
0) ! 247.090 us | }
0) ! 452.702 us | }
0) ! 457.256 us | }
0) 0.488 us | xfs_fs_drop_inode();
0) | xfs_fs_evict_inode() {_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs