Skip to contentSkip to conversation

cpuidle: small improvements & fixes for menu governor (resend)

PATCH In review [email protected] 5 participants 15 messages Nov 3, 2015 – Jan 15, 2016 CPU idle time management framework

lore
Share & tools
lore
#0 lore raw

cover cpuidle: small improvements & fixes for menu governor (resend)

While working on a paravirt cpuidle driver for KVM guests, I noticed a number of small logic errors in the menu governor code.

These patches should get rid of some artifacts that can break the logic in the menu governor under certain corner cases, and make idle state selection work better on CPUs with long C1 exit latencies.

I have not seen any adverse effects with them in my (quick) tests. As expected, they do not seem to do much on systems with many power states and very low C1 exit latencies and target residencies.

#1 lore raw

PATCH 1/3 cpuidle,x86: increase forced cut-off for polling to 20us

From: Rik van Riel <[email protected]>

The cpuidle menu governor has a forced cut-off for polling at 5us, in order to deal with firmware that gives the OS bad information on cpuidle states, leading to the system spending way too much time in polling.

However, at least one x86 CPU family (Atom) has chips that have a 20us break-even point for C1. Forcing the polling cut-off to less than that wastes performance and power.

Increase the polling cut-off to 20us.

Systems with a lower C1 latency will be found in the states table by the menu governor, which will pick those states as appropriate.

---
 drivers/cpuidle/governors/menu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/cpuidle/governors/menu.c +1 -1
index 22e4463d1787..ecc242a586c9 100644
@@ -330,7 +330,7 @@ static int menu_select(struct cpuidle_driver *drv, struct cpuidle_device *dev)
 	 * We want to default to C1 (hlt), not to busy polling
 	 * unless the timer is happening really really soon.
 	 */
-	if (data->next_timer_us > 5 &&
+	if (data->next_timer_us > 20 &&
 	    !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
 		dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
 		data->last_state_idx = CPUIDLE_DRIVER_STATE_START;
Signature · 1 line
2.1.0
#3 lore raw

PATCH 2/3 cpuidle,menu: use interactivity_req to disable polling

In reply to [email protected]

From: Rik van Riel <[email protected]>

The menu governor carefully figures out how much time we typically sleep for an estimated sleep interval, or whether there is a repeating pattern going on, and corrects that estimate for the CPU load.

Then it proceeds to ignore that information when determining whether or not to consider polling. This is not a big deal on most x86 CPUs, which have very low C1 latencies, and the patch should not have any effect on those CPUs.

However, certain CPUs (eg. Atom) have much higher C1 latencies, and it would be good to not waste performance and power on those CPUs if we are expecting a very low wakeup latency.

Disable polling based on the estimated interactivity requirement, not on the time to the next timer interrupt.

---
 drivers/cpuidle/governors/menu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/cpuidle/governors/menu.c +1 -1
index ecc242a586c9..b1a55731f921 100644
@@ -330,7 +330,7 @@ static int menu_select(struct cpuidle_driver *drv, struct cpuidle_device *dev)
 	 * We want to default to C1 (hlt), not to busy polling
 	 * unless the timer is happening really really soon.
 	 */
-	if (data->next_timer_us > 20 &&
+	if (interactivity_req > 20 &&
 	    !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
 		dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
 		data->last_state_idx = CPUIDLE_DRIVER_STATE_START;
Signature · 1 line
2.1.0
Acked-by on v1 2/3
#4 lore raw

Re: [PATCH 2/3] cpuidle,menu: use interactivity_req to disable polling

Quoted 11 lines · On 11/3/2015 2:34 PM, [email protected] wrote:

From: Rik van Riel <[email protected]>

The menu governor carefully figures out how much time we typically sleep for an estimated sleep interval, or whether there is a repeating pattern going on, and corrects that estimate for the CPU load.

Then it proceeds to ignore that information when determining whether or not to consider polling. This is not a big deal on most x86 CPUs, which have very low C1 latencies, and the patch should not have any effect on those CPUs.

Quoted 7 lines

However, certain CPUs (eg. Atom) have much higher C1 latencies, and it would be good to not waste performance and power on those CPUs if we are expecting a very low wakeup latency.

Disable polling based on the estimated interactivity requirement, not on the time to the next timer interrupt.

good catch!

#5 lore raw

Re: [PATCH 2/3] cpuidle,menu: use interactivity_req to disable polling

In reply to [email protected]

Hi Rik,

This change break idle on ARM64(may be on other ARM?) platform. Sorry for reporting late, but missed to check cpuidle in -next.

Quoted 28 lines · On Tue, Nov 3, 2015 at 10:34 PM, <[email protected]> wrote:

From: Rik van Riel <[email protected]>

The menu governor carefully figures out how much time we typically sleep for an estimated sleep interval, or whether there is a repeating pattern going on, and corrects that estimate for the CPU load.

Then it proceeds to ignore that information when determining whether or not to consider polling. This is not a big deal on most x86 CPUs, which have very low C1 latencies, and the patch should not have any effect on those CPUs.

However, certain CPUs (eg. Atom) have much higher C1 latencies, and it would be good to not waste performance and power on those CPUs if we are expecting a very low wakeup latency.

Disable polling based on the estimated interactivity requirement, not on the time to the next timer interrupt.

---
 drivers/cpuidle/governors/menu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/cpuidle/governors/menu.c +0 -0
index ecc242a586c9..b1a55731f921 100644

drivers/cpuidle/governors/menu.c static int menu_select(struct cpuidle_driver *drv, struct cpuidle_device *dev) · line 333

Quoted 5 lines
drivers/cpuidle/governors/menu.c +1 -1
@@ -330,7 +330,7 @@ static int menu_select(struct cpuidle_driver *drv, struct cpuidle_device *dev)
         * We want to default to C1 (hlt), not to busy polling
         * unless the timer is happening really really soon.
         */
-       if (data->next_timer_us > 20 &&
+       if (interactivity_req > 20 &&

I found that data->predicted_us is gets overwritten in get_typical_interval when avg computed = 0 which is the case initially on boot when the past intervals are not yet accumulated.

I just tried a hack and that seem to work and proved what I anticipated (i.e. interactivity_req = 0). Let me know if you have any clues on how to solve it ? I can help you getting the change tested.

Regards,
Sudeep

--->8

drivers/cpuidle/governors/menu.c +0 -0
index 7b0971d97cc3..7c7f4059705a 100644
@@ -330,7 +330,8 @@ static int menu_select(struct cpuidle_driver *drv,

struct cpuidle_device *dev)
* We want to default to C1 (hlt), not to busy polling
* unless the timer is happening really really soon. */
- if (interactivity_req > 20 &&
+ if (((interactivity_req && interactivity_req > 20) ||
+ data->next_timer_us > 20) &&

            !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
                dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
                data->last_state_idx = CPUIDLE_DRIVER_STATE_START;
#6 lore raw

Re: [PATCH 2/3] cpuidle,menu: use interactivity_req to disable polling

Hi,

Quoted 4 lines · Sudeep Holla

Hi Rik,

This change break idle on ARM64(may be on other ARM?) platform. Sorry for reporting late, but missed to check cpuidle in -next.

OK, so first of all, how exactly is idle broken on those systems?

Do they crash or does something different happen? If something different happens, then what's that?

Quoted 53 lines · On Tue, Nov 3, 2015 at 10:34 PM, <[email protected]> wrote:
Quoted 28 lines

From: Rik van Riel <[email protected]>

The menu governor carefully figures out how much time we typically sleep for an estimated sleep interval, or whether there is a repeating pattern going on, and corrects that estimate for the CPU load.

Then it proceeds to ignore that information when determining whether or not to consider polling. This is not a big deal on most x86 CPUs, which have very low C1 latencies, and the patch should not have any effect on those CPUs.

However, certain CPUs (eg. Atom) have much higher C1 latencies, and it would be good to not waste performance and power on those CPUs if we are expecting a very low wakeup latency.

Disable polling based on the estimated interactivity requirement, not on the time to the next timer interrupt.

---
 drivers/cpuidle/governors/menu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/cpuidle/governors/menu.c +0 -0
index ecc242a586c9..b1a55731f921 100644

drivers/cpuidle/governors/menu.c static int menu_select(struct cpuidle_driver *drv, struct cpuidle_device *dev) · line 333

Quoted 5 lines
drivers/cpuidle/governors/menu.c +1 -1
@@ -330,7 +330,7 @@ static int menu_select(struct cpuidle_driver *drv, struct cpuidle_device *dev)
         * We want to default to C1 (hlt), not to busy polling
         * unless the timer is happening really really soon.
         */
-       if (data->next_timer_us > 20 &&
+       if (interactivity_req > 20 &&

I found that data->predicted_us is gets overwritten in get_typical_interval when avg computed = 0 which is the case initially on boot when the past intervals are not yet accumulated.

I just tried a hack and that seem to work and proved what I anticipated (i.e. interactivity_req = 0). Let me know if you have any clues on how to solve it ? I can help you getting the change tested.

Regards,
Sudeep

--->8

drivers/cpuidle/governors/menu.c +0 -0
index 7b0971d97cc3..7c7f4059705a 100644

drivers/cpuidle/governors/menu.c static int menu_select(struct cpuidle_driver *drv, · line 334

Quoted 6 lines
drivers/cpuidle/governors/menu.c +1 -1
@@ -330,7 +330,8 @@ static int menu_select(struct cpuidle_driver *drv,
 struct cpuidle_device *dev)
         * We want to default to C1 (hlt), not to busy polling
         * unless the timer is happening really really soon.
         */
-       if (interactivity_req > 20 &&
+       if (((interactivity_req && interactivity_req > 20) ||

Well, if interactivity_req > 20, then it also is different from 0, so the first check should not be necessary here.

drivers/cpuidle/governors/menu.c static int menu_select(struct cpuidle_driver *drv, · line 335

Quoted 1 line
drivers/cpuidle/governors/menu.c +1 -0
+               data->next_timer_us > 20) &&

I guess that this simply restores the previous behavior on the platforms in question.

Now, the reason why it may matter is because CPUIDLE_DRIVER_STATE_START is 0 and so data->last_state_idx may end up as -1 on them. So I think this piece of code only ever makes sense if CPUIDLE_DRIVER_STATE_START is 1.

Quoted 4 lines
drivers/cpuidle/governors/menu.c +0 -0
            !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
                dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
                data->last_state_idx = CPUIDLE_DRIVER_STATE_START;

--

Thanks,
Rafael

#7 lore raw

Re: [PATCH 2/3] cpuidle,menu: use interactivity_req to disable polling

Quoted 4 lines · Rafael J. Wysocki

Hi,

Quoted 1 line · Sudeep Holla

Hi Rik,

[cut]

Quoted 18 lines

drivers/cpuidle/governors/menu.c static int menu_select(struct cpuidle_driver *drv, · line 334

Quoted 12 lines
drivers/cpuidle/governors/menu.c +1 -1
index 7b0971d97cc3..7c7f4059705a 100644
@@ -330,7 +330,8 @@ static int menu_select(struct cpuidle_driver *drv,
 struct cpuidle_device *dev)
         * We want to default to C1 (hlt), not to busy polling
         * unless the timer is happening really really soon.
         */
-       if (interactivity_req > 20 &&
+       if (((interactivity_req && interactivity_req > 20) ||

Well, if interactivity_req > 20, then it also is different from 0, so the first check should not be necessary here.

drivers/cpuidle/governors/menu.c static int menu_select(struct cpuidle_driver *drv, · line 335

Quoted 1 line
drivers/cpuidle/governors/menu.c +1 -0
+               data->next_timer_us > 20) &&
Quoted 12 lines

I guess that this simply restores the previous behavior on the platforms in question.

Now, the reason why it may matter is because CPUIDLE_DRIVER_STATE_START is 0 and so data->last_state_idx may end up as -1 on them. So I think this piece of code only ever makes sense if CPUIDLE_DRIVER_STATE_START is 1.

Quoted 4 lines
drivers/cpuidle/governors/menu.c +0 -0
            !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
                dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
                data->last_state_idx = CPUIDLE_DRIVER_STATE_START;

--

So I'm wondering if the appended patch helps by any chance?

Rafael

---
 drivers/cpuidle/governors/menu.c |   21 ++++++++++++---------
 1 file changed, 12 insertions(+), 9 deletions(-)
drivers/cpuidle/governors/menu.c +12 -9
Index: linux-pm/drivers/cpuidle/governors/menu.c
===================================================================
@@ -294,8 +294,6 @@ static int menu_select(struct cpuidle_dr
 		data->needs_update = 0;
 	}
 
-	data->last_state_idx = CPUIDLE_DRIVER_STATE_START - 1;
-
 	/* Special case when user has set very strict latency requirement */
 	if (unlikely(latency_req == 0))
 		return 0;
@@ -326,14 +324,19 @@ static int menu_select(struct cpuidle_dr
 	if (latency_req > interactivity_req)
 		latency_req = interactivity_req;
 
-	/*
-	 * We want to default to C1 (hlt), not to busy polling
-	 * unless the timer is happening really really soon.
-	 */
-	if (interactivity_req > 20 &&
-	    !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
-		dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
+	if (CPUIDLE_DRIVER_STATE_START > 0) {
+		data->last_state_idx = CPUIDLE_DRIVER_STATE_START - 1;
+		/*
+		 * We want to default to C1 (hlt), not to busy polling
+		 * unless the timer is happening really really soon.
+		 */
+		if (interactivity_req > 20 &&
+		    !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
+			dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
+			data->last_state_idx = CPUIDLE_DRIVER_STATE_START;
+	} else {
 		data->last_state_idx = CPUIDLE_DRIVER_STATE_START;
+	}
 
 	/*
 	 * Find the idle state with the lowest power while satisfying
#8 lore raw

Re: [PATCH 2/3] cpuidle,menu: use interactivity_req to disable polling

Quoted 1 line · Rafael J. Wysocki

On Wednesday, January 13, 2016 10:58:13 PM Rafael J. Wysocki wrote:

[..]

Quoted 3 lines

So I'm wondering if the appended patch helps by any chance?

Yes it does fix. As you mentioned earlier, CPUIDLE_DRIVER_STATE_START is 0 on ARM platforms and hence data->last_state_idx ended up as -1.

You can add by Tested-by when you push this change. Thanks for the quick fix.

Signature · 2 lines
Regards,
Sudeep
#9 lore raw

Re: [PATCH 2/3] cpuidle,menu: use interactivity_req to disable polling

Quoted 7 lines · Sudeep Holla
Quoted 1 line · Rafael J. Wysocki

On Wednesday, January 13, 2016 10:58:13 PM Rafael J. Wysocki wrote:

[..]

Quoted 1 line
Quoted 8 lines
Quoted 2 lines

So I'm wondering if the appended patch helps by any chance?

Yes it does fix. As you mentioned earlier, CPUIDLE_DRIVER_STATE_START is 0 on ARM platforms and hence data->last_state_idx ended up as -1.

You can add by Tested-by when you push this change. Thanks for the quick fix.

No problem, thanks for testing!

Below it goes again with a changelog and all.

---
From: Rafael J. Wysocki <[email protected]>
Subject: [PATCH] cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0

Commit a9ceb78bc75c (cpuidle,menu: use interactivity_req to disable polling) exposed a bug in menu_select() causing it to return -1 on systems with CPUIDLE_DRIVER_STATE_START equal to zero, although it should have returned 0. As a result, idle states are not entered by CPUs on those systems.

Namely, on the systems in question data->last_state_idx is initially equal to -1 and the above commit modified the condition that would have caused it to be changed to 0 to be less likely to trigger which exposed the problem. However, setting data->last_state_idx initially to -1 doesn't make sense at all and on the affected systems it should always be set to CPUIDLE_DRIVER_STATE_START (ie. 0) unconditionally, so make that happen.

Fixes a9ceb78bc75c (cpuidle,menu: use interactivity_req to disable polling)
Reported-and-tested-by Sudeep Holla <[email protected]>
---
 drivers/cpuidle/governors/menu.c |   21 ++++++++++++---------
 1 file changed, 12 insertions(+), 9 deletions(-)
drivers/cpuidle/governors/menu.c +12 -9
Index: linux-pm/drivers/cpuidle/governors/menu.c
===================================================================
@@ -294,8 +294,6 @@ static int menu_select(struct cpuidle_dr
 		data->needs_update = 0;
 	}
 
-	data->last_state_idx = CPUIDLE_DRIVER_STATE_START - 1;
-
 	/* Special case when user has set very strict latency requirement */
 	if (unlikely(latency_req == 0))
 		return 0;
@@ -326,14 +324,19 @@ static int menu_select(struct cpuidle_dr
 	if (latency_req > interactivity_req)
 		latency_req = interactivity_req;
 
-	/*
-	 * We want to default to C1 (hlt), not to busy polling
-	 * unless the timer is happening really really soon.
-	 */
-	if (interactivity_req > 20 &&
-	    !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
-		dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
+	if (CPUIDLE_DRIVER_STATE_START > 0) {
+		data->last_state_idx = CPUIDLE_DRIVER_STATE_START - 1;
+		/*
+		 * We want to default to C1 (hlt), not to busy polling
+		 * unless the timer is happening really really soon.
+		 */
+		if (interactivity_req > 20 &&
+		    !drv->states[CPUIDLE_DRIVER_STATE_START].disabled &&
+			dev->states_usage[CPUIDLE_DRIVER_STATE_START].disable == 0)
+			data->last_state_idx = CPUIDLE_DRIVER_STATE_START;
+	} else {
 		data->last_state_idx = CPUIDLE_DRIVER_STATE_START;
+	}
 
 	/*
 	 * Find the idle state with the lowest power while satisfying
#10 lore raw

Re: [PATCH 2/3] cpuidle,menu: use interactivity_req to disable polling

In reply to Rafael J. Wysocki
Quoted 10 lines · Rafael J. Wysocki

Hi,

Quoted 4 lines · Sudeep Holla

Hi Rik,

This change break idle on ARM64(may be on other ARM?) platform. Sorry for reporting late, but missed to check cpuidle in -next.

OK, so first of all, how exactly is idle broken on those systems?

Sorry for the hasty bug report.

Quoted 3 lines

Do they crash or does something different happen? If something different happens, then what's that?

No they just don't enter any idle states(as if CPUIdle was disabled)

[...]

Quoted 16 lines

drivers/cpuidle/governors/menu.c static int menu_select(struct cpuidle_driver *drv, · line 334

Quoted 12 lines
drivers/cpuidle/governors/menu.c +1 -1
index 7b0971d97cc3..7c7f4059705a 100644
@@ -330,7 +330,8 @@ static int menu_select(struct cpuidle_driver *drv,
 struct cpuidle_device *dev)
          * We want to default to C1 (hlt), not to busy polling
          * unless the timer is happening really really soon.
          */
-       if (interactivity_req > 20 &&
+       if (((interactivity_req && interactivity_req > 20) ||

Well, if interactivity_req > 20, then it also is different from 0, so the first check should not be necessary here.

True, I just wanted to avoid using interactivity_req when 0, it was just a quick hack.

Quoted 5 lines

drivers/cpuidle/governors/menu.c static int menu_select(struct cpuidle_driver *drv, · line 335

Quoted 1 line
drivers/cpuidle/governors/menu.c +1 -0
+               data->next_timer_us > 20) &&

I guess that this simply restores the previous behavior on the platforms in question.

Yes.

Quoted 5 lines

Now, the reason why it may matter is because CPUIDLE_DRIVER_STATE_START is 0 and so data->last_state_idx may end up as -1 on them. So I think this piece of code only ever makes sense if CPUIDLE_DRIVER_STATE_START is 1.

That's correct.

Signature · 2 lines
Regards,
Sudeep
#11 lore raw

PATCH 3/3 cpuidle,menu: smooth out measured_us calculation

In reply to [email protected]

From: Rik van Riel <[email protected]>

The cpuidle state tables contain the maximum exit latency for each cpuidle state. On x86, that is the exit latency for when the entire package goes into that same idle state.

However, a lot of the time we only go into the core idle state, not the package idle state. This means we see a much smaller exit latency.

We have no way to detect whether we went into the core or package idle state while idle, and that is ok.

However, the current menu_update logic does have the potential to trip up the repeating pattern detection in get_typical_interval. If the system is experiencing an exit latency near the idle state's exit latency, some of the samples will have exit_us subtracted, while others will not. This turns a repeating pattern into mush, potentially breaking get_typical_interval.

Furthermore, for smaller sleep intervals, we know the chance that all the cores in the package went to the same idle state are fairly small. Dividing the measured_us by two, instead of subtracting the full exit latency when hitting a small measured_us, will reduce the error.

---
 drivers/cpuidle/governors/menu.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/cpuidle/governors/menu.c +3 -1
index b1a55731f921..7b0971d97cc3 100644
@@ -404,8 +404,10 @@ static void menu_update(struct cpuidle_driver *drv, struct cpuidle_device *dev)
 	measured_us = cpuidle_get_last_residency(dev);
 
 	/* Deduct exit latency */
-	if (measured_us > target->exit_latency)
+	if (measured_us > 2 * target->exit_latency)
 		measured_us -= target->exit_latency;
+	else
+		measured_us /= 2;
 
 	/* Make sure our coefficients do not exceed unity */
 	if (measured_us > data->next_timer_us)
Signature · 1 line
2.1.0
Acked-by on v1 3/3
#12 lore raw

Re: [PATCH 3/3] cpuidle,menu: smooth out measured_us calculation

Quoted 5 lines · On 11/3/2015 2:34 PM, [email protected] wrote:

Furthermore, for smaller sleep intervals, we know the chance that all the cores in the package went to the same idle state are fairly small. Dividing the measured_us by two, instead of subtracting the full exit latency when hitting a small measured_us, will reduce the error.

there is no perfect answer for this issue; but at least this makes the situation a lot better, so

#13 lore raw
In reply to [email protected]
Quoted 4 lines · On Tuesday, November 03, 2015 05:34:16 PM [email protected] wrote:

While working on a paravirt cpuidle driver for KVM guests, I noticed a number of small logic errors in the menu governor code.

Quoted 8 lines

These patches should get rid of some artifacts that can break the logic in the menu governor under certain corner cases, and make idle state selection work better on CPUs with long C1 exit latencies.

I have not seen any adverse effects with them in my (quick) tests. As expected, they do not seem to do much on systems with many power states and very low C1 exit latencies and target residencies.

Thanks!

The patches look good to me.

I might apply [1-2/3] right away, but I'm a bit hesitant about the [3/3] (I'd like it to spend some time in linux-next before it goes to Linus). Also, we've lived without these changes for quite some time and I don't want to stretch the process too much, so I'll queue them up for v4.5 if that's not a problem.

Thanks,
Rafael

#14 lore raw
Quoted 14 lines · Rafael J. Wysocki
Quoted 4 lines · On Tuesday, November 03, 2015 05:34:16 PM [email protected] wrote:

While working on a paravirt cpuidle driver for KVM guests, I noticed a number of small logic errors in the menu governor code.

Quoted 8 lines

These patches should get rid of some artifacts that can break the logic in the menu governor under certain corner cases, and make idle state selection work better on CPUs with long C1 exit latencies.

I have not seen any adverse effects with them in my (quick) tests. As expected, they do not seem to do much on systems with many power states and very low C1 exit latencies and target residencies.

Quoted 8 lines

Thanks!

The patches look good to me.

I might apply [1-2/3] right away, but I'm a bit hesitant about the [3/3] (I'd like it to spend some time in linux-next before it goes to Linus). Also, we've lived without these changes for quite some time and I don't want to stretch the process too much, so I'll queue them up for v4.5 if that's not a problem.

Not a problem at all. I am all for taking these changes carefully, and seeing what happens.

I did some basic testing with it, but the permutations of what can happen with cpuidle management are just too many to predict in advance everything that could happen.

Signature · 1 line
All rights reversed