Skip to contentSkip to conversation

dd on a lv?

linux-lvm Michael Munger 2 participants 3 messages Nov 8, 2015

lore
Share & tools
lore
#0 lore raw

In preparing a lv for LUKS, I wanted to write random data to the entirety of the logical volume.

(It's one of two lv's in the vg that are running LUKS, the other lv are not encrypted, and all reside on the same pv, which is a linux-raid (mdadm) device at /dev/md0).

I used dd if=/dev/urandom of=/dev/mygroup/mylogicalvolume to write random data to the entirety of the lv device.

Here's the issue:

The lv is only 4TB (yes... this took days). I had estimated it would stop some time early this morning. This afternoon when I checked it, dd had claimed to have written 4.2 TB of data to a 4TB device.

I immediately thought: "How's that possible" and began to worry that it escaped the logical volume and began to write other areas of the array. But, dd if=/dev/mygroup/othervol1 bs=1K count=1 | hexdump -C showed a LUKS header (as it should) and the same command on the other lv showed the proper header as well. I took this to mean that those lv's were in tact.

How is it possible that I can write 4.2TB to a 4.0 TB logical volume? Should I be worried that I have somehow overritten something somewhere else? If so, how do I find and check that? (I have backups, so if I need to restore, I need to do it now).

P.S. When I did this on the other lv, which is only 100GB, dd behaved as expected, and wrote only 100GB of random data to the logical volume.

Signature · 6 lines
Michael Munger, dCAP, MCPS, MCNPS, MBSS
High Powered Help, Inc.
Microsoft Certified Professional
Microsoft Certified Small Business Specialist
Digium Certified Asterisk Professional
[email protected]
#1 lore raw

Dne 8.11.2015 v 18:41 Michael Munger napsal(a):

Quoted 22 lines

In preparing a lv for LUKS, I wanted to write random data to the entirety of the logical volume.

(It's one of two lv's in the vg that are running LUKS, the other lv are not encrypted, and all reside on the same pv, which is a linux-raid (mdadm) device at /dev/md0).

I used dd if=/dev/urandom of=/dev/mygroup/mylogicalvolume to write random data to the entirety of the lv device.

Here's the issue:

The lv is only 4TB (yes... this took days). I had estimated it would stop some time early this morning. This afternoon when I checked it, dd had claimed to have written 4.2 TB of data to a 4TB device.

I immediately thought: "How's that possible" and began to worry that it escaped the logical volume and began to write other areas of the array. But, dd if=/dev/mygroup/othervol1 bs=1K count=1 | hexdump -C showed a LUKS header (as it should) and the same command on the other lv showed the proper header as well. I took this to mean that those lv's were in tact.

Quoted 7 lines

How is it possible that I can write 4.2TB to a 4.0 TB logical volume? Should I be worried that I have somehow overritten something somewhere else? If so, how do I find and check that? (I have backups, so if I need to restore, I need to do it now).

P.S. When I did this on the other lv, which is only 100GB, dd behaved as expected, and wrote only 100GB of random data to the logical volume.

Please check you compare sizes in same 'units'

dd reports sizes in 1000 units
while lvm2 normally in 1024

And basically if you want to hear any 'analysis' - you need to show us

'dmsetup table'

Zdenek

#2 lore raw
Quoted 9 lines · Zdenek Kabelac

Please check you compare sizes in same 'units'

dd reports sizes in 1000 units
while lvm2 normally in 1024

And basically if you want to hear any 'analysis' - you need to show us

'dmsetup table'

This makes sense, and may be what the other poster was saying, but I mis-understood them to have it backwards. If dd is reporting TB (base 1000) and lvm2 is reporting TiB (base 1024), then that's the answer.

Thanks!