mvneta: implement ethtool autonegotiation control

PATCH In review Stas Sergeev 2 participants 4 messages Dec 2, 2015 – Dec 3, 2015

Subsystems (3)

Networking Network drivers Marvell mvneta Ethernet driver

lore

Share & tools

lore

Stas Sergeev

author

2015-12-02 17:32 UTC #0 lore raw

cover mvneta: implement ethtool autonegotiation control

These 2 patches add an ability to control the autonegotiation via ethtool. For example:

ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on

This is needed if you want to connect the mvneta's MII to different switches or PHYs: the ones the do support the in-band status, and the ones that do not.

Stas Sergeev

author

2015-12-02 17:33 UTC #1 lore raw

PATCH 1/2 mvneta: consolidate autoneg enabling

This moves autoneg-related bit manipulations to the single place.

CC Thomas Petazzoni <[email protected]>

CC [email protected]

Signed-off-by Stas Sergeev <[email protected]>

---
 drivers/net/ethernet/marvell/mvneta.c | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

drivers/net/ethernet/marvell/mvneta.c +13 -3

index e84c7f2..8e0e6de 100644
@@ -1065,15 +1065,28 @@ static void mvneta_defaults_set(struct mvneta_port *pp)
 		       MVNETA_GMAC_AN_SPEED_EN |
 		       MVNETA_GMAC_AN_DUPLEX_EN;
 		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+
 		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
 		val |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
 		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
+		val |= MVNETA_GMAC2_INBAND_AN_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
 	} else {
 		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
 		val &= ~(MVNETA_GMAC_INBAND_AN_ENABLE |
 		       MVNETA_GMAC_AN_SPEED_EN |
 		       MVNETA_GMAC_AN_DUPLEX_EN);
 		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
+		val &= ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
+		val &= ~MVNETA_GMAC2_INBAND_AN_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
 	}
 
 	mvneta_set_ucast_table(pp, -1);

@@ -3223,9 +3236,6 @@ static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
 		return -EINVAL;
 	}
 
-	if (pp->use_inband_status)
-		ctrl |= MVNETA_GMAC2_INBAND_AN_ENABLE;
-
 	/* Cancel Port Reset */
 	ctrl &= ~MVNETA_GMAC2_PORT_RESET;
 	mvreg_write(pp, MVNETA_GMAC_CTRL_2, ctrl);

Signature · 1 line

2.4.3

Stas Sergeev

author

2015-12-02 17:35 UTC #2 lore raw

PATCH 2/2 mvneta: implement ethtool autonegotiation control

In reply to Stas Sergeev

This patch allows to do
ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on
to disable or enable autonegotiation at run-time.
Without that functionality, the only way to control the autonegotiation is to modify the device tree.

This is needed if you plan to use the same kernel with different ethernet switches, the ones that support the in-band status and the ones that not.

CC Thomas Petazzoni <[email protected]>

CC [email protected]

Signed-off-by Stas Sergeev <[email protected]>

---
 drivers/net/ethernet/marvell/mvneta.c | 109 +++++++++++++++++++++++-----------
 1 file changed, 74 insertions(+), 35 deletions(-)

drivers/net/ethernet/marvell/mvneta.c +74 ~~-35~~

index 8e0e6de..d0e1ec5 100644
@@ -369,7 +369,7 @@ struct mvneta_port {
 	unsigned int duplex;
 	unsigned int speed;
 	unsigned int tx_csum_limit;
-	int use_inband_status:1;
+	unsigned int use_inband_status:1;
 
 	u64 ethtool_stats[ARRAY_SIZE(mvneta_statistics)];
 };

@@ -971,6 +971,44 @@ static void mvneta_set_other_mcast_table(struct mvneta_port *pp, int queue)
 		mvreg_write(pp, MVNETA_DA_FILT_OTH_MCAST + offset, val);
 }
 
+static void mvneta_set_autoneg(struct mvneta_port *pp, int enable)
+{
+	u32 val;
+
+	if (enable) {
+		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+		val &= ~(MVNETA_GMAC_FORCE_LINK_PASS |
+			 MVNETA_GMAC_FORCE_LINK_DOWN |
+			 MVNETA_GMAC_AN_FLOW_CTRL_EN);
+		val |= MVNETA_GMAC_INBAND_AN_ENABLE |
+		       MVNETA_GMAC_AN_SPEED_EN |
+		       MVNETA_GMAC_AN_DUPLEX_EN;
+		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
+		val |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
+		val |= MVNETA_GMAC2_INBAND_AN_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
+	} else {
+		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+		val &= ~(MVNETA_GMAC_INBAND_AN_ENABLE |
+		       MVNETA_GMAC_AN_SPEED_EN |
+		       MVNETA_GMAC_AN_DUPLEX_EN);
+		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
+		val &= ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
+		val &= ~MVNETA_GMAC2_INBAND_AN_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
+	}
+}
+
 /* This method sets defaults to the NETA port:
  *	Clears interrupt Cause and Mask registers.
  *	Clears all MAC tables.

@@ -1056,39 +1094,7 @@ static void mvneta_defaults_set(struct mvneta_port *pp)
 	val &= ~MVNETA_PHY_POLLING_ENABLE;
 	mvreg_write(pp, MVNETA_UNIT_CONTROL, val);
 
-	if (pp->use_inband_status) {
-		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
-		val &= ~(MVNETA_GMAC_FORCE_LINK_PASS |
-			 MVNETA_GMAC_FORCE_LINK_DOWN |
-			 MVNETA_GMAC_AN_FLOW_CTRL_EN);
-		val |= MVNETA_GMAC_INBAND_AN_ENABLE |
-		       MVNETA_GMAC_AN_SPEED_EN |
-		       MVNETA_GMAC_AN_DUPLEX_EN;
-		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
-
-		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
-		val |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
-		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
-
-		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
-		val |= MVNETA_GMAC2_INBAND_AN_ENABLE;
-		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
-	} else {
-		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
-		val &= ~(MVNETA_GMAC_INBAND_AN_ENABLE |
-		       MVNETA_GMAC_AN_SPEED_EN |
-		       MVNETA_GMAC_AN_DUPLEX_EN);
-		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
-
-		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
-		val &= ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
-		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
-
-		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
-		val &= ~MVNETA_GMAC2_INBAND_AN_ENABLE;
-		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
-	}
-
+	mvneta_set_autoneg(pp, pp->use_inband_status);
 	mvneta_set_ucast_table(pp, -1);
 	mvneta_set_special_mcast_table(pp, -1);
 	mvneta_set_other_mcast_table(pp, -1);

@@ -2950,10 +2956,43 @@ int mvneta_ethtool_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 int mvneta_ethtool_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 {
 	struct mvneta_port *pp = netdev_priv(dev);
+	struct phy_device *phydev = pp->phy_dev;
 
-	if (!pp->phy_dev)
+	if (!phydev)
 		return -ENODEV;
 
+	if ((cmd->autoneg == AUTONEG_ENABLE) != pp->use_inband_status) {
+		u32 val;
+
+		mvneta_set_autoneg(pp, cmd->autoneg == AUTONEG_ENABLE);
+
+		if (cmd->autoneg == AUTONEG_DISABLE) {
+			val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+			val &= ~(MVNETA_GMAC_CONFIG_MII_SPEED |
+				 MVNETA_GMAC_CONFIG_GMII_SPEED |
+				 MVNETA_GMAC_CONFIG_FULL_DUPLEX);
+
+			if (phydev->duplex)
+				val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
+
+			if (phydev->speed == SPEED_1000)
+				val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
+			else if (phydev->speed == SPEED_100)
+				val |= MVNETA_GMAC_CONFIG_MII_SPEED;
+
+			mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+		}
+
+		pp->use_inband_status = (cmd->autoneg == AUTONEG_ENABLE);
+		netdev_info(pp->dev, "autoneg status set to %i\n",
+			    pp->use_inband_status);
+
+		if (netif_running(dev)) {
+			mvneta_port_down(pp);
+			mvneta_port_up(pp);
+		}
+	}
+
 	return phy_ethtool_sset(pp->phy_dev, cmd);
 }

Signature · 1 line

2.4.3

David Miller

maintainer

2015-12-03 20:18 UTC #3 lore raw

In reply to Stas Sergeev

From: Stas Sergeev <[email protected]>
Date: Wed, 2 Dec 2015 20:32:24 +0300

Quoted 9 lines

These 2 patches add an ability to control the autonegotiation via ethtool. For example:
ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on
This is needed if you want to connect the mvneta's MII to different switches or PHYs: the ones the do support the in-band status, and the ones that do not.

Series applied to net-next, thanks.