Skip to contentSkip to conversation

drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt

PATCH Superseded [email protected] 7 participants 17 messages Nov 20, 2015 – Dec 4, 2015

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt

From: Stephen Chandler Paul <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

---
So this one has kind of been a tough sell with Jerome, mostly because it's somewhat of a hack. Unfortunately however I've managed to find machines where DVI hotplugging literally doesn't work without a patch like this. We've already tried a couple of ways of handling the situation of retriggering ddc probes:

* Trying the DDC probe in the radeon_dvi_detect() function multiple times.
* Trying to reschedule the hotplug_work task whenever DDC probing fails on DVI but we got a hpd signal (this ended up being a much more complicated patch then anticipated)
* Doing what we do right now, which is just triggering userspace to rescan all the ports when the hpd signal is asserted by the DVI port but there's no DDC probe, and repeating until at least a second passes.

All of these actually work, but I guess it's a question of which one is less of a hack. If anyone here can think of a cleaner way of handling this feel free to let me know.

 drivers/gpu/drm/radeon/radeon.h            |  3 +++
 drivers/gpu/drm/radeon/radeon_connectors.c | 20 +++++++++++++++++---
 drivers/gpu/drm/radeon/radeon_irq_kms.c    |  2 ++
 3 files changed, 22 insertions(+), 3 deletions(-)
drivers/gpu/drm/radeon/radeon.h +3 -0
index b6cbd81..d63f0fe 100644
@@ -2460,6 +2460,9 @@ struct radeon_device {
 	/* amdkfd interface */
 	struct kfd_dev		*kfd;
 
+	/* last time we received an hpd signal */
+	unsigned long hpd_time;
+
 	struct mutex	mn_lock;
 	DECLARE_HASHTABLE(mn_hash, 7);
 };
drivers/gpu/drm/radeon/radeon_connectors.c +17 -3
index 5a2cafb..4ee9440 100644
@@ -1228,19 +1228,33 @@ radeon_dvi_detect(struct drm_connector *connector, bool force)
 	const struct drm_encoder_helper_funcs *encoder_funcs;
 	int i, r;
 	enum drm_connector_status ret = connector_status_disconnected;
-	bool dret = false, broken_edid = false;
+	bool dret = false, broken_edid = false, hpd_unchanged;
 
 	r = pm_runtime_get_sync(connector->dev->dev);
 	if (r < 0)
 		return connector_status_disconnected;
 
-	if (!force && radeon_check_hpd_status_unchanged(connector)) {
+	hpd_unchanged = radeon_check_hpd_status_unchanged(connector);
+	if (!force && hpd_unchanged) {
 		ret = connector->status;
 		goto exit;
 	}
 
-	if (radeon_connector->ddc_bus)
+	if (radeon_connector->ddc_bus) {
 		dret = radeon_ddc_probe(radeon_connector, false);
+
+		/* Sometimes the pins required for the DDC probe on DVI
+		 * connectors don't make contact at the same time that the ones
+		 * for HPD do. If the DDC probe fails even though we had an HPD
+		 * signal, signal userspace to try again */
+		if (!dret && !hpd_unchanged &&
+		    connector->status != connector_status_connected &&
+		    time_before(jiffies, rdev->hpd_time + msecs_to_jiffies(1000))) {
+			DRM_DEBUG_KMS("%s: hpd asserted but ddc probe failed, retrying\n",
+				      connector->name);
+			drm_sysfs_hotplug_event(dev);
+		}
+	}
 	if (dret) {
 		radeon_connector->detected_by_load = false;
 		radeon_connector_free_edid(connector);
drivers/gpu/drm/radeon/radeon_irq_kms.c +2 -0
index 171d3e4..579c22c 100644
@@ -79,6 +79,8 @@ static void radeon_hotplug_work_func(struct work_struct *work)
 	struct drm_mode_config *mode_config = &dev->mode_config;
 	struct drm_connector *connector;
 
+	rdev->hpd_time = jiffies;
+
 	/* we can race here at startup, some boards seem to trigger
 	 * hotplug irqs when they shouldn't. */
 	if (!rdev->mode_info.mode_config_initialized)
Signature · 1 line
2.5.0
maintainer
#1 lore raw
Quoted 13 lines · On 20.11.2015 16:52, [email protected] wrote:

From: Stephen Chandler Paul <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Quoted 5 lines

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I know the HPD pins don't necessary have an RC circuit so we might need to handle this case in software here.

A delay of something between 10-30ms between the last HPD interrupt and further processing of the signal doesn't sounds like such a bad idea.

Retrying on the other hand doesn't necessarily improve the situation cause the delay introduced by this might not be enough.

So I would rather vote for a fixed delay between an HPD interrupt and actually starting to process anything.

Regards,
Christian.

Quoted 83 lines

---
So this one has kind of been a tough sell with Jerome, mostly because it's somewhat of a hack. Unfortunately however I've managed to find machines where DVI hotplugging literally doesn't work without a patch like this. We've already tried a couple of ways of handling the situation of retriggering ddc probes:

* Trying the DDC probe in the radeon_dvi_detect() function multiple times.
* Trying to reschedule the hotplug_work task whenever DDC probing fails on DVI but we got a hpd signal (this ended up being a much more complicated patch then anticipated)
* Doing what we do right now, which is just triggering userspace to rescan all the ports when the hpd signal is asserted by the DVI port but there's no DDC probe, and repeating until at least a second passes.

All of these actually work, but I guess it's a question of which one is less of a hack. If anyone here can think of a cleaner way of handling this feel free to let me know.

  drivers/gpu/drm/radeon/radeon.h            |  3 +++
  drivers/gpu/drm/radeon/radeon_connectors.c | 20 +++++++++++++++++---
  drivers/gpu/drm/radeon/radeon_irq_kms.c    |  2 ++
  3 files changed, 22 insertions(+), 3 deletions(-)
drivers/gpu/drm/radeon/radeon.h +3 -0
index b6cbd81..d63f0fe 100644
@@ -2460,6 +2460,9 @@ struct radeon_device {
  	/* amdkfd interface */
  	struct kfd_dev		*kfd;
 
+	/* last time we received an hpd signal */
+	unsigned long hpd_time;
+
  	struct mutex	mn_lock;
  	DECLARE_HASHTABLE(mn_hash, 7);
  };
drivers/gpu/drm/radeon/radeon_connectors.c +17 -3
index 5a2cafb..4ee9440 100644
@@ -1228,19 +1228,33 @@ radeon_dvi_detect(struct drm_connector *connector, bool force)
  	const struct drm_encoder_helper_funcs *encoder_funcs;
  	int i, r;
  	enum drm_connector_status ret = connector_status_disconnected;
-	bool dret = false, broken_edid = false;
+	bool dret = false, broken_edid = false, hpd_unchanged;
 
  	r = pm_runtime_get_sync(connector->dev->dev);
  	if (r < 0)
  		return connector_status_disconnected;
 
-	if (!force && radeon_check_hpd_status_unchanged(connector)) {
+	hpd_unchanged = radeon_check_hpd_status_unchanged(connector);
+	if (!force && hpd_unchanged) {
  		ret = connector->status;
  		goto exit;
  	}
 
-	if (radeon_connector->ddc_bus)
+	if (radeon_connector->ddc_bus) {
  		dret = radeon_ddc_probe(radeon_connector, false);
+
+		/* Sometimes the pins required for the DDC probe on DVI
+		 * connectors don't make contact at the same time that the ones
+		 * for HPD do. If the DDC probe fails even though we had an HPD
+		 * signal, signal userspace to try again */
+		if (!dret && !hpd_unchanged &&
+		    connector->status != connector_status_connected &&
+		    time_before(jiffies, rdev->hpd_time + msecs_to_jiffies(1000))) {
+			DRM_DEBUG_KMS("%s: hpd asserted but ddc probe failed, retrying\n",
+				      connector->name);
+			drm_sysfs_hotplug_event(dev);
+		}
+	}
  	if (dret) {
  		radeon_connector->detected_by_load = false;
  		radeon_connector_free_edid(connector);
drivers/gpu/drm/radeon/radeon_irq_kms.c +0 -0
index 171d3e4..579c22c 100644

drivers/gpu/drm/radeon/radeon_irq_kms.c static void radeon_hotplug_work_func(struct work_struct *work) · line 86

Quoted 8 lines
drivers/gpu/drm/radeon/radeon_irq_kms.c +2 -0
@@ -79,6 +79,8 @@ static void radeon_hotplug_work_func(struct work_struct *work)
  	struct drm_mode_config *mode_config = &dev->mode_config;
  	struct drm_connector *connector;
 
+	rdev->hpd_time = jiffies;
+
  	/* we can race here at startup, some boards seem to trigger
  	 * hotplug irqs when they shouldn't. */
  	if (!rdev->mode_info.mode_config_initialized)

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

#2 lore raw

Hi,

Quoted 20 lines · Christian König
Quoted 11 lines · On 20.11.2015 16:52, [email protected] wrote:

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I know the HPD pins don't necessary have an RC circuit so we might need to handle this case in software here.

Quoted 8 lines

A delay of something between 10-30ms between the last HPD interrupt and further processing of the signal doesn't sounds like such a bad idea.

Retrying on the other hand doesn't necessarily improve the situation cause the delay introduced by this might not be enough.

So I would rather vote for a fixed delay between an HPD interrupt and actually starting to process anything.

Yes-ish. Debouncing is useful, and ignoring buggy devices (e.g. those on marginal power) which send you HPD storms as well. But DP relies on 'short HPD' pulses which can be as brief as 2ms. So attempting to totally debounce all HPD won't work.

Cheers,
Daniel
_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

maintainer
#3 lore raw
Quoted 28 lines · Daniel Stone

Hi,

Quoted 25 lines · Christian König
Quoted 11 lines · On 20.11.2015 16:52, [email protected] wrote:

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I know the HPD pins don't necessary have an RC circuit so we might need to handle this case in software here.

A delay of something between 10-30ms between the last HPD interrupt and further processing of the signal doesn't sounds like such a bad idea.

Retrying on the other hand doesn't necessarily improve the situation cause the delay introduced by this might not be enough.

Quoted 6 lines
Quoted 2 lines

So I would rather vote for a fixed delay between an HPD interrupt and actually starting to process anything.

Yes-ish. Debouncing is useful, and ignoring buggy devices (e.g. those on marginal power) which send you HPD storms as well. But DP relies on 'short HPD' pulses which can be as brief as 2ms. So attempting to totally debounce all HPD won't work.

Well the discussion so far was about HPD on DVI only.

I'm not so deep into DP, but why should it uses HPD pulses of less than 2ms?

Regards,
Christian.

Quoted 3 lines

Cheers,
Daniel

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

author
#4 lore raw
Quoted 32 lines · Christian König
Quoted 31 lines · Daniel Stone

Hi,

Quoted 27 lines · Christian König
Quoted 10 lines · On 20.11.2015 16:52, [email protected] wrote:

This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.

Quoted 7 lines

Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I
know the HPD pins don't necessary have an RC circuit so we might need to
handle this case in software here.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

A delay of something between 10-30ms between the last HPD interrupt and
further processing of the signal doesn't sounds like such a bad idea.

Unfortunately the delay needed to make hotplugging work on the system mentioned in the commit log can actually be over 700ms.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

Retrying on the other hand doesn't necessarily improve the situation cause
the delay introduced by this might not be enough.

Yeah, but I would think it would make sense to retry here so long as we back off after a certain time. This would also have the benefit of skipping this delay on systems that don't need it.

Quoted 10 lines
Quoted 10 lines
Quoted 4 lines

So I would rather vote for a fixed delay between an HPD interrupt and
actually starting to process anything.

Yes-ish. Debouncing is useful, and ignoring buggy devices (e.g. those
on marginal power) which send you HPD storms as well. But DP relies on
'short HPD' pulses which can be as brief as 2ms. So attempting to totally debounce all HPD won't work.

Quoted 4 lines

Well the discussion so far was about HPD on DVI only.

I'm not so deep into DP, but why should it uses HPD pulses of less than 2ms?

This is part of the DP spec iirc. This being said though, the issue here with the HPD signal coming before the connector is ready only happens on DVI. I haven't ever run into this issue with any HDMI cables or DP cables, so I'm against imposing this on all connectors.

One of the solutions I've been thinking about with this: In radeon_dvi_detect(), if we get a real hotplug signal retry the DDC probe until at least a second has passed, after which we back off and assume the port is disconnected.

Quoted 8 lines

Regards,
Christian.

Quoted 3 lines

Cheers,
Daniel

Signature · 7 lines
Cheers,
	Lyude

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel
#5 lore raw
Quoted 74 lines

-----Original Message-----
From: Lyude [mailto:[email protected]]
Sent: Sunday, November 22, 2015 9:45 PM
To: Koenig, Christian; Daniel Stone
Cc: Deucher, Alexander; David Airlie; dri-devel; Linux Kernel Mailing List; Jerome Glisse; Benjamin Tissoires
Subject: Re: [PATCH] drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt

Quoted 32 lines · Christian König
Quoted 31 lines · Daniel Stone

Hi,

Quoted 27 lines · Christian König
Quoted 10 lines · On 20.11.2015 16:52, [email protected] wrote:

This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.

Quoted 7 lines

Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I
know the HPD pins don't necessary have an RC circuit so we might need to
handle this case in software here.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

A delay of something between 10-30ms between the last HPD interrupt and
further processing of the signal doesn't sounds like such a bad idea.

Unfortunately the delay needed to make hotplugging work on the system mentioned in the commit log can actually be over 700ms.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

Retrying on the other hand doesn't necessarily improve the situation cause
the delay introduced by this might not be enough.

Yeah, but I would think it would make sense to retry here so long as we back off after a certain time. This would also have the benefit of skipping this delay on systems that don't need it.

Quoted 10 lines
Quoted 10 lines
Quoted 4 lines

So I would rather vote for a fixed delay between an HPD interrupt and
actually starting to process anything.

Yes-ish. Debouncing is useful, and ignoring buggy devices (e.g. those
on marginal power) which send you HPD storms as well. But DP relies on
'short HPD' pulses which can be as brief as 2ms. So attempting to totally debounce all HPD won't work.

Quoted 4 lines

Well the discussion so far was about HPD on DVI only.

I'm not so deep into DP, but why should it uses HPD pulses of less than 2ms?

This is part of the DP spec iirc. This being said though, the issue here with the HPD signal coming before the connector is ready only happens on DVI. I haven't ever run into this issue with any HDMI cables or DP cables, so I'm against imposing this on all connectors.

Quoted 4 lines

One of the solutions I've been thinking about with this: In radeon_dvi_detect(), if we get a real hotplug signal retry the DDC probe until at least a second has passed, after which we back off and assume the port is disconnected.

FWIW, there are registers to adjust how long the hpd needs to be asserted before the hpd connection and short pulse interrupts are triggered. See DC_HPDx_CONTROL. Maybe adjusting them would help. We currently just write the default value, but it might be better to RMW the value in case there is a special golden value set by the vbios at init time.

Alex

Quoted 11 lines
Quoted 8 lines

Regards,
Christian.

Quoted 3 lines

Cheers,
Daniel

--
Cheers,
Lyude

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

author
#6 lore raw
Quoted 79 lines · Alexander
Quoted 74 lines

-----Original Message-----
From: Lyude [mailto:[email protected]]
Sent: Sunday, November 22, 2015 9:45 PM
To: Koenig, Christian; Daniel Stone
Cc: Deucher, Alexander; David Airlie; dri-devel; Linux Kernel Mailing List; Jerome Glisse; Benjamin Tissoires
Subject: Re: [PATCH] drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt

Quoted 32 lines · Christian König
Quoted 31 lines · Daniel Stone

Hi,

Quoted 27 lines · Christian König
Quoted 10 lines · On 20.11.2015 16:52, [email protected] wrote:

This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.

Quoted 7 lines

Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I
know the HPD pins don't necessary have an RC circuit so we might need to
handle this case in software here.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

A delay of something between 10-30ms between the last HPD interrupt and
further processing of the signal doesn't sounds like such a bad idea.

Unfortunately the delay needed to make hotplugging work on the system mentioned in the commit log can actually be over 700ms.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

Retrying on the other hand doesn't necessarily improve the situation cause
the delay introduced by this might not be enough.

Yeah, but I would think it would make sense to retry here so long as we back off after a certain time. This would also have the benefit of skipping this delay on systems that don't need it.

Quoted 10 lines
Quoted 10 lines
Quoted 4 lines

So I would rather vote for a fixed delay between an HPD interrupt and
actually starting to process anything.

Yes-ish. Debouncing is useful, and ignoring buggy devices (e.g. those
on marginal power) which send you HPD storms as well. But DP relies on
'short HPD' pulses which can be as brief as 2ms. So attempting to totally debounce all HPD won't work.

Quoted 4 lines

Well the discussion so far was about HPD on DVI only.

I'm not so deep into DP, but why should it uses HPD pulses of less than 2ms?

This is part of the DP spec iirc. This being said though, the issue here with the HPD signal coming before the connector is ready only happens on DVI. I haven't ever run into this issue with any HDMI cables or DP cables, so I'm against imposing this on all connectors.

Quoted 4 lines

One of the solutions I've been thinking about with this: In radeon_dvi_detect(), if we get a real hotplug signal retry the DDC probe until at least a second has passed, after which we back off and assume the port is disconnected.

Quoted 6 lines

FWIW, there are registers to adjust how long the hpd needs to be asserted before the hpd connection and short pulse interrupts are triggered.  See DC_HPDx_CONTROL.  Maybe adjusting them would help.  We currently just write the default value, but it might be better to RMW the value in case there is a special golden value set by the vbios at init time.

This sounds like a much better idea. I'm going to try to come up with a patch that adjusts these by default for DVI ports.

Quoted 14 lines

Alex

Quoted 11 lines
Quoted 8 lines

Regards,
Christian.

Quoted 3 lines

Cheers,
Daniel

--
Cheers,
Lyude

Signature · 7 lines
Cheers,
	Lyude

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel
author
#7 lore raw
Quoted 88 lines · Lyude
Quoted 80 lines · Alexander
Quoted 75 lines

-----Original Message-----
From: Lyude [mailto:[email protected]]
Sent: Sunday, November 22, 2015 9:45 PM
To: Koenig, Christian; Daniel Stone
Cc: Deucher, Alexander; David Airlie; dri-devel; Linux Kernel Mailing List;
Jerome Glisse; Benjamin Tissoires
Subject: Re: [PATCH] drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt

Quoted 32 lines · Christian König
Quoted 31 lines · Daniel Stone

Hi,

Quoted 27 lines · Christian König
Quoted 10 lines · On 20.11.2015 16:52, [email protected] wrote:

This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.

Quoted 7 lines

Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I
know the HPD pins don't necessary have an RC circuit so we might need to
handle this case in software here.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

A delay of something between 10-30ms between the last HPD interrupt and
further processing of the signal doesn't sounds like such a bad idea.

Unfortunately the delay needed to make hotplugging work on the system mentioned in the commit log can actually be over 700ms.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

Retrying on the other hand doesn't necessarily improve the situation cause
the delay introduced by this might not be enough.

Yeah, but I would think it would make sense to retry here so long as we back off after a certain time. This would also have the benefit of skipping this delay on systems that don't need it.

Quoted 10 lines
Quoted 10 lines
Quoted 4 lines

So I would rather vote for a fixed delay between an HPD interrupt and
actually starting to process anything.

Yes-ish. Debouncing is useful, and ignoring buggy devices (e.g. those
on marginal power) which send you HPD storms as well. But DP relies on
'short HPD' pulses which can be as brief as 2ms. So attempting to totally debounce all HPD won't work.

Quoted 4 lines

Well the discussion so far was about HPD on DVI only.

I'm not so deep into DP, but why should it uses HPD pulses of less than 2ms?

This is part of the DP spec iirc. This being said though, the issue here with the HPD signal coming before the connector is ready only happens on DVI. I haven't ever run into this issue with any HDMI cables or DP cables, so I'm against imposing this on all connectors.

Quoted 4 lines

One of the solutions I've been thinking about with this: In radeon_dvi_detect(), if we get a real hotplug signal retry the DDC probe until at least a second has passed, after which we back off and assume the port is disconnected.

Quoted 7 lines

FWIW, there are registers to adjust how long the hpd needs to be asserted before the hpd connection and short pulse interrupts are triggered.  See DC_HPDx_CONTROL.  Maybe adjusting them would help.  We currently just write the default value, but it might be better to RMW the value in case there is a
special golden value set by the vbios at init time.

Quoted 2 lines

This sounds like a much better idea. I'm going to try to come up with a patch that adjusts these by default for DVI ports.

Ignore this; we can't get a long enough delay using those registers to fix the issue so we'll still have to handle this in software.

Quoted 14 lines
Quoted 14 lines

Alex

Quoted 11 lines
Quoted 8 lines

Regards,
Christian.

Quoted 3 lines

Cheers,
Daniel

--
Cheers,
Lyude

Signature · 7 lines
Cheers,
	Lyude

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel
author
#8 lore raw
In reply to Deucher, Alexander

Ping
Do we have any consensus on the best way of handling this situation in the driver?

Quoted 99 lines · Alexander
Quoted 74 lines

-----Original Message-----
From: Lyude [mailto:[email protected]]
Sent: Sunday, November 22, 2015 9:45 PM
To: Koenig, Christian; Daniel Stone
Cc: Deucher, Alexander; David Airlie; dri-devel; Linux Kernel Mailing List; Jerome Glisse; Benjamin Tissoires
Subject: Re: [PATCH] drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt

Quoted 32 lines · Christian König
Quoted 31 lines · Daniel Stone

Hi,

Quoted 27 lines · Christian König
Quoted 10 lines · On 20.11.2015 16:52, [email protected] wrote:

This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.

Quoted 7 lines

Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I
know the HPD pins don't necessary have an RC circuit so we might need to
handle this case in software here.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

A delay of something between 10-30ms between the last HPD interrupt and
further processing of the signal doesn't sounds like such a bad idea.

Unfortunately the delay needed to make hotplugging work on the system mentioned in the commit log can actually be over 700ms.

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

Retrying on the other hand doesn't necessarily improve the situation cause
the delay introduced by this might not be enough.

Yeah, but I would think it would make sense to retry here so long as we back off after a certain time. This would also have the benefit of skipping this delay on systems that don't need it.

Quoted 10 lines
Quoted 10 lines
Quoted 4 lines

So I would rather vote for a fixed delay between an HPD interrupt and
actually starting to process anything.

Yes-ish. Debouncing is useful, and ignoring buggy devices (e.g. those
on marginal power) which send you HPD storms as well. But DP relies on
'short HPD' pulses which can be as brief as 2ms. So attempting to totally debounce all HPD won't work.

Quoted 4 lines

Well the discussion so far was about HPD on DVI only.

I'm not so deep into DP, but why should it uses HPD pulses of less than 2ms?

This is part of the DP spec iirc. This being said though, the issue here with the HPD signal coming before the connector is ready only happens on DVI. I haven't ever run into this issue with any HDMI cables or DP cables, so I'm against imposing this on all connectors.

Quoted 4 lines

One of the solutions I've been thinking about with this: In radeon_dvi_detect(), if we get a real hotplug signal retry the DDC probe until at least a second has passed, after which we back off and assume the port is disconnected.

FWIW, there are registers to adjust how long the hpd needs to be asserted before the hpd connection and short pulse interrupts are triggered.  See DC_HPDx_CONTROL.  Maybe adjusting them would help.  We currently just write the default value, but it might be better to RMW the value in case there is a special golden value set by the vbios at init time.

Alex

Quoted 11 lines
Quoted 8 lines

Regards,
Christian.

Quoted 3 lines

Cheers,
Daniel

--
Cheers,
Lyude

Signature · 7 lines
Cheers,
	Lyude

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel
#9 lore raw

PATCH v2 1/1 drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt

In reply to Deucher, Alexander

From: Lyude <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

---
Sending this version of the patch because Jerome says this will probably be the least controversial of the potential fixes. Instead of sending userspace tons of hotplug events, we just reschedule the hotplug work.

 drivers/gpu/drm/radeon/cik.c               |  2 +-
 drivers/gpu/drm/radeon/evergreen.c         |  2 +-
 drivers/gpu/drm/radeon/r100.c              |  2 +-
 drivers/gpu/drm/radeon/r600.c              |  2 +-
 drivers/gpu/drm/radeon/radeon.h            |  2 +-
 drivers/gpu/drm/radeon/radeon_connectors.c | 21 ++++++++++++++++++++-
 drivers/gpu/drm/radeon/radeon_irq_kms.c    |  8 ++++----
 drivers/gpu/drm/radeon/radeon_mode.h       |  1 +
 drivers/gpu/drm/radeon/rs600.c             |  2 +-
 drivers/gpu/drm/radeon/si.c                |  2 +-
 10 files changed, 32 insertions(+), 12 deletions(-)
drivers/gpu/drm/radeon/cik.c +1 -1
index 248953d..6801a0c 100644
@@ -8472,7 +8472,7 @@ restart_ih:
 	if (queue_dp)
 		schedule_work(&rdev->dp_work);
 	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
 	if (queue_reset) {
 		rdev->needs_reset = true;
 		wake_up_all(&rdev->fence_queue);
drivers/gpu/drm/radeon/evergreen.c +1 -1
index 0acde19..f8e4986 100644
@@ -5368,7 +5368,7 @@ restart_ih:
 	if (queue_dp)
 		schedule_work(&rdev->dp_work);
 	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
 	if (queue_hdmi)
 		schedule_work(&rdev->audio_work);
 	if (queue_thermal && rdev->pm.dpm_enabled)
drivers/gpu/drm/radeon/r100.c +1 -1
index 238b13f..2df3c86 100644
@@ -806,7 +806,7 @@ int r100_irq_process(struct radeon_device *rdev)
 		status = r100_irq_ack(rdev);
 	}
 	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
 	if (rdev->msi_enabled) {
 		switch (rdev->family) {
 		case CHIP_RS400:
drivers/gpu/drm/radeon/r600.c +1 -1
index 4ea5b10..cc2fdf0 100644
@@ -4276,7 +4276,7 @@ restart_ih:
 		WREG32(IH_RB_RPTR, rptr);
 	}
 	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
 	if (queue_hdmi)
 		schedule_work(&rdev->audio_work);
 	if (queue_thermal && rdev->pm.dpm_enabled)
drivers/gpu/drm/radeon/radeon.h +1 -1
index b6cbd81..87db649 100644
@@ -2414,7 +2414,7 @@ struct radeon_device {
 	struct r600_ih ih; /* r6/700 interrupt ring */
 	struct radeon_rlc rlc;
 	struct radeon_mec mec;
-	struct work_struct hotplug_work;
+	struct delayed_work hotplug_work;
 	struct work_struct dp_work;
 	struct work_struct audio_work;
 	int num_crtc; /* number of crtcs */
drivers/gpu/drm/radeon/radeon_connectors.c +20 -1
index 5a2cafb..340f3f5 100644
@@ -1234,13 +1234,32 @@ radeon_dvi_detect(struct drm_connector *connector, bool force)
 	if (r < 0)
 		return connector_status_disconnected;
 
+	if (radeon_connector->detected_hpd_without_ddc) {
+		force = true;
+		radeon_connector->detected_hpd_without_ddc = false;
+	}
+
 	if (!force && radeon_check_hpd_status_unchanged(connector)) {
 		ret = connector->status;
 		goto exit;
 	}
 
-	if (radeon_connector->ddc_bus)
+	if (radeon_connector->ddc_bus) {
 		dret = radeon_ddc_probe(radeon_connector, false);
+
+		/* Sometimes the pins required for the DDC probe on DVI
+		 * connectors don't make contact at the same time that the ones
+		 * for HPD do. If the DDC probe fails even though we had an HPD
+		 * signal, try again later */
+		if (!dret && !force &&
+		    connector->status != connector_status_connected) {
+			DRM_DEBUG_KMS("hpd detected without ddc, retrying in 1 second\n");
+			radeon_connector->detected_hpd_without_ddc = true;
+			schedule_delayed_work(&rdev->hotplug_work,
+					      msecs_to_jiffies(1000));
+			goto exit;
+		}
+	}
 	if (dret) {
 		radeon_connector->detected_by_load = false;
 		radeon_connector_free_edid(connector);
drivers/gpu/drm/radeon/radeon_irq_kms.c +4 -4
index 171d3e4..979f3bf 100644
@@ -74,7 +74,7 @@ irqreturn_t radeon_driver_irq_handler_kms(int irq, void *arg)
 static void radeon_hotplug_work_func(struct work_struct *work)
 {
 	struct radeon_device *rdev = container_of(work, struct radeon_device,
-						  hotplug_work);
+						  hotplug_work.work);
 	struct drm_device *dev = rdev->ddev;
 	struct drm_mode_config *mode_config = &dev->mode_config;
 	struct drm_connector *connector;
@@ -302,7 +302,7 @@ int radeon_irq_kms_init(struct radeon_device *rdev)
 		}
 	}
 
-	INIT_WORK(&rdev->hotplug_work, radeon_hotplug_work_func);
+	INIT_DELAYED_WORK(&rdev->hotplug_work, radeon_hotplug_work_func);
 	INIT_WORK(&rdev->dp_work, radeon_dp_work_func);
 	INIT_WORK(&rdev->audio_work, r600_audio_update_hdmi);
 
@@ -310,7 +310,7 @@ int radeon_irq_kms_init(struct radeon_device *rdev)
 	r = drm_irq_install(rdev->ddev, rdev->ddev->pdev->irq);
 	if (r) {
 		rdev->irq.installed = false;
-		flush_work(&rdev->hotplug_work);
+		flush_delayed_work(&rdev->hotplug_work);
 		return r;
 	}
 
@@ -333,7 +333,7 @@ void radeon_irq_kms_fini(struct radeon_device *rdev)
 		rdev->irq.installed = false;
 		if (rdev->msi_enabled)
 			pci_disable_msi(rdev->pdev);
-		flush_work(&rdev->hotplug_work);
+		flush_delayed_work(&rdev->hotplug_work);
 	}
 }
 
drivers/gpu/drm/radeon/radeon_mode.h +1 -0
index 457b026..0aeb3ee 100644
@@ -553,6 +553,7 @@ struct radeon_connector {
 	void *con_priv;
 	bool dac_load_detect;
 	bool detected_by_load; /* if the connection status was determined by load */
+	bool detected_hpd_without_ddc; /* if an HPD signal was detected on DVI, but ddc probing failed */
 	uint16_t connector_object_id;
 	struct radeon_hpd hpd;
 	struct radeon_router router;
drivers/gpu/drm/radeon/rs600.c +1 -1
index 97a9048..6244f4e 100644
@@ -813,7 +813,7 @@ int rs600_irq_process(struct radeon_device *rdev)
 		status = rs600_irq_ack(rdev);
 	}
 	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
 	if (queue_hdmi)
 		schedule_work(&rdev->audio_work);
 	if (rdev->msi_enabled) {
drivers/gpu/drm/radeon/si.c +1 -1
index 07037e3..fb1a7ec 100644
@@ -6848,7 +6848,7 @@ restart_ih:
 	if (queue_dp)
 		schedule_work(&rdev->dp_work);
 	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
 	if (queue_thermal && rdev->pm.dpm_enabled)
 		schedule_work(&rdev->pm.dpm.thermal.work);
 	rdev->ih.rptr = rptr;
Signature · 1 line
2.5.0
maintainer
#10 lore raw
Quoted 13 lines · On 04.12.2015 00:26, [email protected] wrote:

From: Lyude <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Quoted 5 lines

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

I find a second a bit long, but if it works so what?

Looks sane enough to me, patch is Reviewed-by: Christian König <[email protected]>

Quoted 198 lines

---
Sending this version of the patch because Jerome says this will probably be the least controversial of the potential fixes. Instead of sending userspace tons of hotplug events, we just reschedule the hotplug work.

  drivers/gpu/drm/radeon/cik.c               |  2 +-
  drivers/gpu/drm/radeon/evergreen.c         |  2 +-
  drivers/gpu/drm/radeon/r100.c              |  2 +-
  drivers/gpu/drm/radeon/r600.c              |  2 +-
  drivers/gpu/drm/radeon/radeon.h            |  2 +-
  drivers/gpu/drm/radeon/radeon_connectors.c | 21 ++++++++++++++++++++-
  drivers/gpu/drm/radeon/radeon_irq_kms.c    |  8 ++++----
  drivers/gpu/drm/radeon/radeon_mode.h       |  1 +
  drivers/gpu/drm/radeon/rs600.c             |  2 +-
  drivers/gpu/drm/radeon/si.c                |  2 +-
  10 files changed, 32 insertions(+), 12 deletions(-)
drivers/gpu/drm/radeon/cik.c +1 -1
index 248953d..6801a0c 100644
@@ -8472,7 +8472,7 @@ restart_ih:
  	if (queue_dp)
  		schedule_work(&rdev->dp_work);
  	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
  	if (queue_reset) {
  		rdev->needs_reset = true;
  		wake_up_all(&rdev->fence_queue);
drivers/gpu/drm/radeon/evergreen.c +1 -1
index 0acde19..f8e4986 100644
@@ -5368,7 +5368,7 @@ restart_ih:
  	if (queue_dp)
  		schedule_work(&rdev->dp_work);
  	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
  	if (queue_hdmi)
  		schedule_work(&rdev->audio_work);
  	if (queue_thermal && rdev->pm.dpm_enabled)
drivers/gpu/drm/radeon/r100.c +1 -1
index 238b13f..2df3c86 100644
@@ -806,7 +806,7 @@ int r100_irq_process(struct radeon_device *rdev)
  		status = r100_irq_ack(rdev);
  	}
  	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
  	if (rdev->msi_enabled) {
  		switch (rdev->family) {
  		case CHIP_RS400:
drivers/gpu/drm/radeon/r600.c +1 -1
index 4ea5b10..cc2fdf0 100644
@@ -4276,7 +4276,7 @@ restart_ih:
  		WREG32(IH_RB_RPTR, rptr);
  	}
  	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
  	if (queue_hdmi)
  		schedule_work(&rdev->audio_work);
  	if (queue_thermal && rdev->pm.dpm_enabled)
drivers/gpu/drm/radeon/radeon.h +1 -1
index b6cbd81..87db649 100644
@@ -2414,7 +2414,7 @@ struct radeon_device {
  	struct r600_ih ih; /* r6/700 interrupt ring */
  	struct radeon_rlc rlc;
  	struct radeon_mec mec;
-	struct work_struct hotplug_work;
+	struct delayed_work hotplug_work;
  	struct work_struct dp_work;
  	struct work_struct audio_work;
  	int num_crtc; /* number of crtcs */
drivers/gpu/drm/radeon/radeon_connectors.c +20 -1
index 5a2cafb..340f3f5 100644
@@ -1234,13 +1234,32 @@ radeon_dvi_detect(struct drm_connector *connector, bool force)
  	if (r < 0)
  		return connector_status_disconnected;
 
+	if (radeon_connector->detected_hpd_without_ddc) {
+		force = true;
+		radeon_connector->detected_hpd_without_ddc = false;
+	}
+
  	if (!force && radeon_check_hpd_status_unchanged(connector)) {
  		ret = connector->status;
  		goto exit;
  	}
 
-	if (radeon_connector->ddc_bus)
+	if (radeon_connector->ddc_bus) {
  		dret = radeon_ddc_probe(radeon_connector, false);
+
+		/* Sometimes the pins required for the DDC probe on DVI
+		 * connectors don't make contact at the same time that the ones
+		 * for HPD do. If the DDC probe fails even though we had an HPD
+		 * signal, try again later */
+		if (!dret && !force &&
+		    connector->status != connector_status_connected) {
+			DRM_DEBUG_KMS("hpd detected without ddc, retrying in 1 second\n");
+			radeon_connector->detected_hpd_without_ddc = true;
+			schedule_delayed_work(&rdev->hotplug_work,
+					      msecs_to_jiffies(1000));
+			goto exit;
+		}
+	}
  	if (dret) {
  		radeon_connector->detected_by_load = false;
  		radeon_connector_free_edid(connector);
drivers/gpu/drm/radeon/radeon_irq_kms.c +4 -4
index 171d3e4..979f3bf 100644
@@ -74,7 +74,7 @@ irqreturn_t radeon_driver_irq_handler_kms(int irq, void *arg)
  static void radeon_hotplug_work_func(struct work_struct *work)
  {
  	struct radeon_device *rdev = container_of(work, struct radeon_device,
-						  hotplug_work);
+						  hotplug_work.work);
  	struct drm_device *dev = rdev->ddev;
  	struct drm_mode_config *mode_config = &dev->mode_config;
  	struct drm_connector *connector;
@@ -302,7 +302,7 @@ int radeon_irq_kms_init(struct radeon_device *rdev)
  		}
  	}
 
-	INIT_WORK(&rdev->hotplug_work, radeon_hotplug_work_func);
+	INIT_DELAYED_WORK(&rdev->hotplug_work, radeon_hotplug_work_func);
  	INIT_WORK(&rdev->dp_work, radeon_dp_work_func);
  	INIT_WORK(&rdev->audio_work, r600_audio_update_hdmi);
 
@@ -310,7 +310,7 @@ int radeon_irq_kms_init(struct radeon_device *rdev)
  	r = drm_irq_install(rdev->ddev, rdev->ddev->pdev->irq);
  	if (r) {
  		rdev->irq.installed = false;
-		flush_work(&rdev->hotplug_work);
+		flush_delayed_work(&rdev->hotplug_work);
  		return r;
  	}
 
@@ -333,7 +333,7 @@ void radeon_irq_kms_fini(struct radeon_device *rdev)
  		rdev->irq.installed = false;
  		if (rdev->msi_enabled)
  			pci_disable_msi(rdev->pdev);
-		flush_work(&rdev->hotplug_work);
+		flush_delayed_work(&rdev->hotplug_work);
  	}
  }
 
drivers/gpu/drm/radeon/radeon_mode.h +1 -0
index 457b026..0aeb3ee 100644
@@ -553,6 +553,7 @@ struct radeon_connector {
  	void *con_priv;
  	bool dac_load_detect;
  	bool detected_by_load; /* if the connection status was determined by load */
+	bool detected_hpd_without_ddc; /* if an HPD signal was detected on DVI, but ddc probing failed */
  	uint16_t connector_object_id;
  	struct radeon_hpd hpd;
  	struct radeon_router router;
drivers/gpu/drm/radeon/rs600.c +1 -1
index 97a9048..6244f4e 100644
@@ -813,7 +813,7 @@ int rs600_irq_process(struct radeon_device *rdev)
  		status = rs600_irq_ack(rdev);
  	}
  	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
  	if (queue_hdmi)
  		schedule_work(&rdev->audio_work);
  	if (rdev->msi_enabled) {
drivers/gpu/drm/radeon/si.c +1 -1
index 07037e3..fb1a7ec 100644
@@ -6848,7 +6848,7 @@ restart_ih:
  	if (queue_dp)
  		schedule_work(&rdev->dp_work);
  	if (queue_hotplug)
-		schedule_work(&rdev->hotplug_work);
+		schedule_delayed_work(&rdev->hotplug_work, 0);
  	if (queue_thermal && rdev->pm.dpm_enabled)
  		schedule_work(&rdev->pm.dpm.thermal.work);
  	rdev->ih.rptr = rptr;
#11 lore raw

2015-12-04 09:53 keltezéssel, Christian König írta:

Quoted 18 lines · On 04.12.2015 00:26, [email protected] wrote:
Quoted 17 lines

From: Lyude <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

Quoted 5 lines
Quoted 1 line

I find a second a bit long, but if it works so what?

Looks sane enough to me, patch is Reviewed-by: Christian König <[email protected]>

Does this patch help in case of the Radeon chip only has HDMI and DP outputs exposed (Zotac ZBOXNANO-AQ01) but used with DVI or VGA monitors with converter cables? We have some problems with such scenarios that sounds eerily similar to this description.

;-)

Thanks in advance.

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

maintainer
#12 lore raw
Quoted 19 lines · Boszormenyi Zoltan

2015-12-04 09:53 keltezéssel, Christian König írta:

Quoted 18 lines · On 04.12.2015 00:26, [email protected] wrote:
Quoted 17 lines

From: Lyude <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

Quoted 8 lines
Quoted 4 lines
Quoted 1 line

I find a second a bit long, but if it works so what?

Looks sane enough to me, patch is Reviewed-by: Christian König <[email protected]>

Does this patch help in case of the Radeon chip only has HDMI and DP outputs exposed (Zotac ZBOXNANO-AQ01) but used with DVI or VGA monitors with converter cables? We have some problems with such scenarios that sounds eerily similar to this description.

No, at least active converter cables are a completely different case.

Regards,
Christian.

Quoted 6 lines

;-)

Thanks in advance.

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

Applied
#13 lore raw
In reply to Christian König
Quoted 19 lines · Christian König
Quoted 18 lines · On 04.12.2015 00:26, [email protected] wrote:

From: Lyude <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

Quoted 7 lines
Quoted 1 line

I find a second a bit long, but if it works so what?

Looks sane enough to me, patch is Reviewed-by: Christian König <[email protected]>

Applied. thanks!

Alex

Quoted 208 lines
Quoted 208 lines

---
Sending this version of the patch because Jerome says this will probably be the
least controversial of the potential fixes. Instead of sending userspace tons of
hotplug events, we just reschedule the hotplug work.

  drivers/gpu/drm/radeon/cik.c               |  2 +-
  drivers/gpu/drm/radeon/evergreen.c         |  2 +-
  drivers/gpu/drm/radeon/r100.c              |  2 +-
  drivers/gpu/drm/radeon/r600.c              |  2 +-
  drivers/gpu/drm/radeon/radeon.h            |  2 +-
  drivers/gpu/drm/radeon/radeon_connectors.c | 21 ++++++++++++++++++++-
  drivers/gpu/drm/radeon/radeon_irq_kms.c    |  8 ++++----
  drivers/gpu/drm/radeon/radeon_mode.h       |  1 +
  drivers/gpu/drm/radeon/rs600.c             |  2 +-
  drivers/gpu/drm/radeon/si.c                |  2 +-
  10 files changed, 32 insertions(+), 12 deletions(-)
drivers/gpu/drm/radeon/cik.c +1 -1
index 248953d..6801a0c 100644
@@ -8472,7 +8472,7 @@ restart_ih:
        if (queue_dp)
                schedule_work(&rdev->dp_work);
        if (queue_hotplug)
-               schedule_work(&rdev->hotplug_work);
+               schedule_delayed_work(&rdev->hotplug_work, 0);
        if (queue_reset) {
                rdev->needs_reset = true;
                wake_up_all(&rdev->fence_queue);
drivers/gpu/drm/radeon/evergreen.c +1 -1
index 0acde19..f8e4986 100644
@@ -5368,7 +5368,7 @@ restart_ih:
        if (queue_dp)
                schedule_work(&rdev->dp_work);
        if (queue_hotplug)
-               schedule_work(&rdev->hotplug_work);
+               schedule_delayed_work(&rdev->hotplug_work, 0);
        if (queue_hdmi)
                schedule_work(&rdev->audio_work);
        if (queue_thermal && rdev->pm.dpm_enabled)
drivers/gpu/drm/radeon/r100.c +1 -1
index 238b13f..2df3c86 100644
@@ -806,7 +806,7 @@ int r100_irq_process(struct radeon_device *rdev)
                status = r100_irq_ack(rdev);
        }
        if (queue_hotplug)
-               schedule_work(&rdev->hotplug_work);
+               schedule_delayed_work(&rdev->hotplug_work, 0);
        if (rdev->msi_enabled) {
                switch (rdev->family) {
                case CHIP_RS400:
drivers/gpu/drm/radeon/r600.c +1 -1
index 4ea5b10..cc2fdf0 100644
@@ -4276,7 +4276,7 @@ restart_ih:
                WREG32(IH_RB_RPTR, rptr);
        }
        if (queue_hotplug)
-               schedule_work(&rdev->hotplug_work);
+               schedule_delayed_work(&rdev->hotplug_work, 0);
        if (queue_hdmi)
                schedule_work(&rdev->audio_work);
        if (queue_thermal && rdev->pm.dpm_enabled)
drivers/gpu/drm/radeon/radeon.h +1 -1
index b6cbd81..87db649 100644
@@ -2414,7 +2414,7 @@ struct radeon_device {
        struct r600_ih ih; /* r6/700 interrupt ring */
        struct radeon_rlc rlc;
        struct radeon_mec mec;
-       struct work_struct hotplug_work;
+       struct delayed_work hotplug_work;
        struct work_struct dp_work;
        struct work_struct audio_work;
        int num_crtc; /* number of crtcs */
drivers/gpu/drm/radeon/radeon_connectors.c +8 -0
index 5a2cafb..340f3f5 100644
@@ -1234,13 +1234,32 @@ radeon_dvi_detect(struct drm_connector *connector,
 bool force)
        if (r < 0)
                return connector_status_disconnected;
  +     if (radeon_connector->detected_hpd_without_ddc) {
+               force = true;
+               radeon_connector->detected_hpd_without_ddc = false;
+       }
+
        if (!force && radeon_check_hpd_status_unchanged(connector)) {
                ret = connector->status;
                goto exit;
        }
  -     if (radeon_connector->ddc_bus)
+       if (radeon_connector->ddc_bus) {
                dret = radeon_ddc_probe(radeon_connector, false);
+
+               /* Sometimes the pins required for the DDC probe on DVI
+                * connectors don't make contact at the same time that the

ones
+ * for HPD do. If the DDC probe fails even though we had
an HPD

drivers/gpu/drm/radeon/radeon_connectors.c +4 -0
+                * signal, try again later */
+               if (!dret && !force &&
+                   connector->status != connector_status_connected) {
+                       DRM_DEBUG_KMS("hpd detected without ddc, retrying

in 1 second\n");

drivers/gpu/drm/radeon/radeon_connectors.c +6 -0
+                       radeon_connector->detected_hpd_without_ddc = true;
+                       schedule_delayed_work(&rdev->hotplug_work,
+                                             msecs_to_jiffies(1000));
+                       goto exit;
+               }
+       }
        if (dret) {
                radeon_connector->detected_by_load = false;
                radeon_connector_free_edid(connector);
drivers/gpu/drm/radeon/radeon_irq_kms.c +1 -1
index 171d3e4..979f3bf 100644
@@ -74,7 +74,7 @@ irqreturn_t radeon_driver_irq_handler_kms(int irq, void
 *arg)
  static void radeon_hotplug_work_func(struct work_struct *work)
  {
        struct radeon_device *rdev = container_of(work, struct
 radeon_device,
-                                                 hotplug_work);
+                                                 hotplug_work.work);
        struct drm_device *dev = rdev->ddev;
        struct drm_mode_config *mode_config = &dev->mode_config;
        struct drm_connector *connector;
drivers/gpu/drm/radeon/radeon_irq_kms.c +3 -2
@@ -302,7 +302,7 @@ int radeon_irq_kms_init(struct radeon_device *rdev)
                }
        }
  -     INIT_WORK(&rdev->hotplug_work, radeon_hotplug_work_func);
+       INIT_DELAYED_WORK(&rdev->hotplug_work, radeon_hotplug_work_func);
        INIT_WORK(&rdev->dp_work, radeon_dp_work_func);
        INIT_WORK(&rdev->audio_work, r600_audio_update_hdmi);
  @@ -310,7 +310,7 @@ int radeon_irq_kms_init(struct radeon_device *rdev)
        r = drm_irq_install(rdev->ddev, rdev->ddev->pdev->irq);
        if (r) {
                rdev->irq.installed = false;
-               flush_work(&rdev->hotplug_work);
+               flush_delayed_work(&rdev->hotplug_work);
                return r;
        }
  @@ -333,7 +333,7 @@ void radeon_irq_kms_fini(struct radeon_device *rdev)
                rdev->irq.installed = false;
                if (rdev->msi_enabled)
                        pci_disable_msi(rdev->pdev);
-               flush_work(&rdev->hotplug_work);
+               flush_delayed_work(&rdev->hotplug_work);
        }
  }
  diff --git a/drivers/gpu/drm/radeon/radeon_mode.h

b/drivers/gpu/drm/radeon/radeon_mode.h
index 457b026..0aeb3ee 100644

drivers/gpu/drm/radeon/radeon_mode.h +0 -0
@@ -553,6 +553,7 @@ struct radeon_connector {
        void *con_priv;
        bool dac_load_detect;
        bool detected_by_load; /* if the connection status was determined

by load */
+ bool detected_hpd_without_ddc; /* if an HPD signal was detected on
DVI, but ddc probing failed */

        uint16_t connector_object_id;
        struct radeon_hpd hpd;
        struct radeon_router router;
drivers/gpu/drm/radeon/rs600.c +1 -1
index 97a9048..6244f4e 100644
@@ -813,7 +813,7 @@ int rs600_irq_process(struct radeon_device *rdev)
                status = rs600_irq_ack(rdev);
        }
        if (queue_hotplug)
-               schedule_work(&rdev->hotplug_work);
+               schedule_delayed_work(&rdev->hotplug_work, 0);
        if (queue_hdmi)
                schedule_work(&rdev->audio_work);
        if (rdev->msi_enabled) {
drivers/gpu/drm/radeon/si.c +1 -1
index 07037e3..fb1a7ec 100644
@@ -6848,7 +6848,7 @@ restart_ih:
        if (queue_dp)
                schedule_work(&rdev->dp_work);
        if (queue_hotplug)
-               schedule_work(&rdev->hotplug_work);
+               schedule_delayed_work(&rdev->hotplug_work, 0);
        if (queue_thermal && rdev->pm.dpm_enabled)
Quoted 8 lines

drivers/gpu/drm/radeon/si.c restart_ih: · line 6854

Quoted 2 lines
drivers/gpu/drm/radeon/si.c +0 -0
                schedule_work(&rdev->pm.dpm.thermal.work);
        rdev->ih.rptr = rptr;

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

#14 lore raw
In reply to Daniel Stone
Quoted 29 lines · Daniel Stone

Hi,

Quoted 26 lines · Christian König
Quoted 11 lines · On 20.11.2015 16:52, [email protected] wrote:

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I know the HPD pins don't necessary have an RC circuit so we might need to handle this case in software here.

A delay of something between 10-30ms between the last HPD interrupt and further processing of the signal doesn't sounds like such a bad idea.

Retrying on the other hand doesn't necessarily improve the situation cause the delay introduced by this might not be enough.

Quoted 7 lines
Quoted 2 lines

So I would rather vote for a fixed delay between an HPD interrupt and actually starting to process anything.

Yes-ish. Debouncing is useful, and ignoring buggy devices (e.g. those on marginal power) which send you HPD storms as well. But DP relies on 'short HPD' pulses which can be as brief as 2ms. So attempting to totally debounce all HPD won't work.

In our experience in i915 DP hpd works perfectly on all machines. At least we never had to add timeout hacks to settle hpd, storm handling code isn't enabled for DP either and we always checked hpd status bits to decide whether something is connected or not.

hdmi/dvi is the troublemaker which needs settling time and storm handling. -Daniel

Signature · 3 lines
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
#15 lore raw
In reply to Christian König
Quoted 26 lines · Christian König
Quoted 13 lines · On 20.11.2015 16:52, [email protected] wrote:

From: Stephen Chandler Paul <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Quoted 5 lines

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

Yeah, that's something I always wondered a about bit as well.

Debouncing is something very common done in electronics, but as far as I know the HPD pins don't necessary have an RC circuit so we might need to handle this case in software here.

Quoted 8 lines

A delay of something between 10-30ms between the last HPD interrupt and further processing of the signal doesn't sounds like such a bad idea.

Retrying on the other hand doesn't necessarily improve the situation cause the delay introduced by this might not be enough.

So I would rather vote for a fixed delay between an HPD interrupt and actually starting to process anything.

Might be interesting to compare what we do in i915 in latest kernels:

- in the hpd handler we check the hpd status bits before probing the edid. This will take care of slow unplug case where we get the hpd interrupt/status change, but i2c is still working.

- but because crap screens (or whatever it is) if hpd is _not_ set we retest the status for 30ms (and bail out as soon as hpd status is asserted). This seems to be enough time to settle all screens.

Note that this is in intel_hdmi.c since native dvi ports on intel hw also always supported hdmi features. Not sure whether we could extract this into some kind of helper and share.
-Daniel

Quoted 95 lines

Regards,
Christian.

Quoted 79 lines

---
So this one has kind of been a tough sell with Jerome, mostly because it's somewhat of a hack. Unfortunately however I've managed to find machines where DVI hotplugging literally doesn't work without a patch like this. We've already tried a couple of ways of handling the situation of retriggering ddc probes:

* Trying the DDC probe in the radeon_dvi_detect() function multiple times.
* Trying to reschedule the hotplug_work task whenever DDC probing fails on DVI but we got a hpd signal (this ended up being a much more complicated patch then anticipated)
* Doing what we do right now, which is just triggering userspace to rescan all the ports when the hpd signal is asserted by the DVI port but there's no DDC probe, and repeating until at least a second passes.

All of these actually work, but I guess it's a question of which one is less of a hack. If anyone here can think of a cleaner way of handling this feel free to let me know.

 drivers/gpu/drm/radeon/radeon.h            |  3 +++
 drivers/gpu/drm/radeon/radeon_connectors.c | 20 +++++++++++++++++---
 drivers/gpu/drm/radeon/radeon_irq_kms.c    |  2 ++
 3 files changed, 22 insertions(+), 3 deletions(-)
drivers/gpu/drm/radeon/radeon.h +3 -0
index b6cbd81..d63f0fe 100644
@@ -2460,6 +2460,9 @@ struct radeon_device {
 	/* amdkfd interface */
 	struct kfd_dev		*kfd;
+	/* last time we received an hpd signal */
+	unsigned long hpd_time;
+
 	struct mutex	mn_lock;
 	DECLARE_HASHTABLE(mn_hash, 7);
 };
drivers/gpu/drm/radeon/radeon_connectors.c +17 -3
index 5a2cafb..4ee9440 100644
@@ -1228,19 +1228,33 @@ radeon_dvi_detect(struct drm_connector *connector, bool force)
 	const struct drm_encoder_helper_funcs *encoder_funcs;
 	int i, r;
 	enum drm_connector_status ret = connector_status_disconnected;
-	bool dret = false, broken_edid = false;
+	bool dret = false, broken_edid = false, hpd_unchanged;
 	r = pm_runtime_get_sync(connector->dev->dev);
 	if (r < 0)
 		return connector_status_disconnected;
-	if (!force && radeon_check_hpd_status_unchanged(connector)) {
+	hpd_unchanged = radeon_check_hpd_status_unchanged(connector);
+	if (!force && hpd_unchanged) {
 		ret = connector->status;
 		goto exit;
 	}
-	if (radeon_connector->ddc_bus)
+	if (radeon_connector->ddc_bus) {
 		dret = radeon_ddc_probe(radeon_connector, false);
+
+		/* Sometimes the pins required for the DDC probe on DVI
+		 * connectors don't make contact at the same time that the ones
+		 * for HPD do. If the DDC probe fails even though we had an HPD
+		 * signal, signal userspace to try again */
+		if (!dret && !hpd_unchanged &&
+		    connector->status != connector_status_connected &&
+		    time_before(jiffies, rdev->hpd_time + msecs_to_jiffies(1000))) {
+			DRM_DEBUG_KMS("%s: hpd asserted but ddc probe failed, retrying\n",
+				      connector->name);
+			drm_sysfs_hotplug_event(dev);
+		}
+	}
 	if (dret) {
 		radeon_connector->detected_by_load = false;
 		radeon_connector_free_edid(connector);
drivers/gpu/drm/radeon/radeon_irq_kms.c +0 -0
index 171d3e4..579c22c 100644

drivers/gpu/drm/radeon/radeon_irq_kms.c static void radeon_hotplug_work_func(struct work_struct *work) · line 85

Quoted 7 lines
drivers/gpu/drm/radeon/radeon_irq_kms.c +2 -0
@@ -79,6 +79,8 @@ static void radeon_hotplug_work_func(struct work_struct *work)
 	struct drm_mode_config *mode_config = &dev->mode_config;
 	struct drm_connector *connector;
+	rdev->hpd_time = jiffies;
+
 	/* we can race here at startup, some boards seem to trigger
 	 * hotplug irqs when they shouldn't. */
 	if (!rdev->mode_info.mode_config_initialized)

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

Signature · 7 lines
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel
#16 lore raw
In reply to [email protected]

2015-11-20 16:52 keltezéssel, [email protected] írta:

Quoted 101 lines

From: Stephen Chandler Paul <[email protected]>

HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing.

This is somewhat rare on most cards (depending on what angle you plug the DVI connector in), but on some cards it happens constantly. The Radeon R5 on the machine used for testing this patch for instance, runs into this issue just about every time I try to hotplug a DVI monitor and as a result hotplugging almost never works.

Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue.

---
So this one has kind of been a tough sell with Jerome, mostly because it's somewhat of a hack. Unfortunately however I've managed to find machines where DVI hotplugging literally doesn't work without a patch like this. We've already tried a couple of ways of handling the situation of retriggering ddc probes:

* Trying the DDC probe in the radeon_dvi_detect() function multiple times.
* Trying to reschedule the hotplug_work task whenever DDC probing fails on DVI but we got a hpd signal (this ended up being a much more complicated patch then anticipated)
* Doing what we do right now, which is just triggering userspace to rescan all the ports when the hpd signal is asserted by the DVI port but there's no DDC probe, and repeating until at least a second passes.

All of these actually work, but I guess it's a question of which one is less of a hack. If anyone here can think of a cleaner way of handling this feel free to let me know.

 drivers/gpu/drm/radeon/radeon.h            |  3 +++
 drivers/gpu/drm/radeon/radeon_connectors.c | 20 +++++++++++++++++---
 drivers/gpu/drm/radeon/radeon_irq_kms.c    |  2 ++
 3 files changed, 22 insertions(+), 3 deletions(-)
drivers/gpu/drm/radeon/radeon.h +3 -0
index b6cbd81..d63f0fe 100644
@@ -2460,6 +2460,9 @@ struct radeon_device {
 	/* amdkfd interface */
 	struct kfd_dev		*kfd;
 
+	/* last time we received an hpd signal */
+	unsigned long hpd_time;
+
 	struct mutex	mn_lock;
 	DECLARE_HASHTABLE(mn_hash, 7);
 };
drivers/gpu/drm/radeon/radeon_connectors.c +17 -3
index 5a2cafb..4ee9440 100644
@@ -1228,19 +1228,33 @@ radeon_dvi_detect(struct drm_connector *connector, bool force)
 	const struct drm_encoder_helper_funcs *encoder_funcs;
 	int i, r;
 	enum drm_connector_status ret = connector_status_disconnected;
-	bool dret = false, broken_edid = false;
+	bool dret = false, broken_edid = false, hpd_unchanged;
 
 	r = pm_runtime_get_sync(connector->dev->dev);
 	if (r < 0)
 		return connector_status_disconnected;
 
-	if (!force && radeon_check_hpd_status_unchanged(connector)) {
+	hpd_unchanged = radeon_check_hpd_status_unchanged(connector);
+	if (!force && hpd_unchanged) {
 		ret = connector->status;
 		goto exit;
 	}
 
-	if (radeon_connector->ddc_bus)
+	if (radeon_connector->ddc_bus) {
 		dret = radeon_ddc_probe(radeon_connector, false);
+
+		/* Sometimes the pins required for the DDC probe on DVI
+		 * connectors don't make contact at the same time that the ones
+		 * for HPD do. If the DDC probe fails even though we had an HPD
+		 * signal, signal userspace to try again */
+		if (!dret && !hpd_unchanged &&
+		    connector->status != connector_status_connected &&
+		    time_before(jiffies, rdev->hpd_time + msecs_to_jiffies(1000))) {
+			DRM_DEBUG_KMS("%s: hpd asserted but ddc probe failed, retrying\n",
+				      connector->name);
+			drm_sysfs_hotplug_event(dev);
+		}
+	}
 	if (dret) {
 		radeon_connector->detected_by_load = false;
 		radeon_connector_free_edid(connector);
drivers/gpu/drm/radeon/radeon_irq_kms.c +0 -0
index 171d3e4..579c22c 100644

drivers/gpu/drm/radeon/radeon_irq_kms.c static void radeon_hotplug_work_func(struct work_struct *work) · line 86

Quoted 8 lines
drivers/gpu/drm/radeon/radeon_irq_kms.c +2 -0
@@ -79,6 +79,8 @@ static void radeon_hotplug_work_func(struct work_struct *work)
 	struct drm_mode_config *mode_config = &dev->mode_config;
 	struct drm_connector *connector;
 
+	rdev->hpd_time = jiffies;
+
 	/* we can race here at startup, some boards seem to trigger
 	 * hotplug irqs when they shouldn't. */
 	if (!rdev->mode_info.mode_config_initialized)

Does this patch help in case I use a DP-2-DVI-D or HDMI-2-DVI-D converter cable?

Thanks in advance,
Zoltán Böszörményi

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel