irqchip: Add brcm,bcm6345-l1-intc device tree binding

new file mode 100644
index 0000000..4040905
@@ -0,0 +1,57 @@
+Broadcom BCM6345-style Level 1 interrupt controller
+
+This block is a first level interrupt controller that is typically connected
+directly to one of the HW INT lines on each CPU.
+
+Key elements of the hardware design include:
+
+- 32, 64 or 128 incoming level IRQ lines
+
+- Most onchip peripherals are wired directly to an L1 input
+
+- A separate instance of the register set for each CPU, allowing individual
+  peripheral IRQs to be routed to any CPU
+
+- Contains one or more enable/status word pairs per CPU
+
+- No atomic set/clear operations
+
+- No polarity/level/edge settings
+
+- No FIFO or priority encoder logic; software is expected to read all
+  2-4 status words to determine which IRQs are pending
+
+Required properties:
+
+- compatible: should be "brcm,bcm<soc>-l1-intc", "brcm,bcm6345-l1-intc"
+- reg: specifies the base physical address and size of the registers;
+  the number of supported IRQs is inferred from the size argument
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
+  this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+  node; valid values depend on the type of parent interrupt controller
+
+If multiple reg ranges and interrupt-parent entries are present on an SMP
+system, the driver will allow IRQ SMP affinity to be set up through the
+/proc/irq/ interface.  In the simplest possible configuration, only one
+reg range and one interrupt-parent is needed.
+
+The driver operates in native CPU endian by default, there is no support for
+specifying an alternative endianness.
+
+Example:
+
+periph_intc: interrupt-controller@10000000 {
+        compatible = "brcm,bcm63168-l1-intc", "brcm,bcm6345-l1-intc";
+        reg = <0x10000020 0x20>,
+              <0x10000040 0x20>;
+
+        interrupt-controller;
+        #interrupt-cells = <1>;
+
+        interrupt-parent = <&cpu_intc>;
+        interrupts = <2>, <3>;
+};

index 82f296a..9c49d4e 100644
@@ -2387,6 +2387,7 @@ F:	arch/mips/bmips/*
 F:	arch/mips/include/asm/mach-bmips/*
 F:	arch/mips/kernel/*bmips*
 F:	arch/mips/boot/dts/brcm/bcm*.dts*
+F:	drivers/irqchip/irq-bcm63*
 F:	drivers/irqchip/irq-bcm7*
 F:	drivers/irqchip/irq-brcmstb*
 

index fbf3f66..9caf55a 100644
@@ -151,6 +151,7 @@ config BMIPS_GENERIC
 	select CSRC_R4K
 	select SYNC_R4K
 	select COMMON_CLK
+	select BCM6345_L1_IRQ
 	select BCM7038_L1_IRQ
 	select BCM7120_L2_IRQ
 	select BRCMSTB_L2_IRQ

index 4d7294e..d307bb3 100644
@@ -65,6 +65,11 @@ config I8259
 	bool
 	select IRQ_DOMAIN
 
+config BCM6345_L1_IRQ
+	bool
+	select GENERIC_IRQ_CHIP
+	select IRQ_DOMAIN
+
 config BCM7038_L1_IRQ
 	bool
 	select GENERIC_IRQ_CHIP

index 177f78f..ded59cf 100644
@@ -43,6 +43,7 @@ obj-$(CONFIG_XTENSA)			+= irq-xtensa-pic.o
 obj-$(CONFIG_XTENSA_MX)			+= irq-xtensa-mx.o
 obj-$(CONFIG_IRQ_CROSSBAR)		+= irq-crossbar.o
 obj-$(CONFIG_SOC_VF610)			+= irq-vf610-mscm-ir.o
+obj-$(CONFIG_BCM6345_L1_IRQ)		+= irq-bcm6345-l1.o
 obj-$(CONFIG_BCM7038_L1_IRQ)		+= irq-bcm7038-l1.o
 obj-$(CONFIG_BCM7120_L2_IRQ)		+= irq-bcm7120-l2.o
 obj-$(CONFIG_BRCMSTB_L2_IRQ)		+= irq-brcmstb-l2.o