clk: tegra: Fix warning caused by pll_u failing to lock
Subsystems (3)
Jon Hunter
maintainerPATCH 1/2 clk: tegra: Fix warning caused by pll_u failing to lock
If the pll_u is not configured by the bootloader, then on kernel boot the following warning is seen:
clk_pll_wait_for_lock: Timed out waiting for pll pll_u_vco lock
tegra_init_from_table: Failed to enable pll_u_out1
------------[ cut here ]------------ WARNING: at drivers/clk/tegra/clk.c:269 Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc4-next-20151214+ #1 Hardware name: NVIDIA Tegra210 P2371 reference board (E.1) (DT) task: ffffffc0bc0a0000 ti: ffffffc0bc0a8000 task.ti: ffffffc0bc0a8000 PC is at tegra_init_from_table+0x140/0x164 LR is at tegra_init_from_table+0x140/0x164 pc : [<ffffffc0008fee78>] lr : [<ffffffc0008fee78>] pstate: 80000045 sp : ffffffc0bc0abd50 x29: ffffffc0bc0abd50 x28: ffffffc00090b8a8 x27: ffffffc000a06000 x26: ffffffc0bc019780 x25: ffffffc00086a708 x24: ffffffc00086a790 x23: ffffffc0006d7188 x22: ffffffc0bc010000 x21: 000000000000016e x20: ffffffc0bc00d100 x19: ffffffc000944178 x18: 0000000000000007 x17: 000000000000000e x16: 0000000000000001 x15: 0000000000000007 x14: 000000000000000e x13: 0000000000000013 x12: 000000000000001a x11: 000000000000004d x10: 0000000000000750 x9 : ffffffc0bc0a8000 x8 : ffffffc0bc0a07b0 x7 : 0000000000000001 x6 : 0000000002d5f0f8 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000002 x2 : ffffffc000996724 x1 : 0000000000000000 x0 : 0000000000000032 ---[ end trace cbd20ae519e92ced ]--- Call trace: [<ffffffc0008fee78>] tegra_init_from_table+0x140/0x164 [<ffffffc000900ac8>] tegra210_clock_apply_init_table+0x20/0x28 [<ffffffc0008fec40>] tegra_clocks_apply_init_table+0x18/0x24 [<ffffffc00008291c>] do_one_initcall+0x90/0x194 [<ffffffc0008cfab0>] kernel_init_freeable+0x148/0x1e8 [<ffffffc000636bb0>] kernel_init+0x10/0xdc [<ffffffc000085cd0>] ret_from_fork+0x10/0x40 clk_pll_wait_for_lock: Timed out waiting for pll pll_u_vco lock tegra_init_from_table: Failed to enable pll_u_out2 ------------[ cut here ]------------
pll_u can be either controlled by software or hardware and this is selected via the OVERRIDE bit in the pll_u base register. In the function tegra210_pll_init(), the OVERRIDE bit for pll_u is cleared, which selects hardware control of the pll. However, at the same time the pll_u clocks are populated in the init_table for tegra210 and so software will try to configure the pll_u if it is not already configured and hence, the above warning is seen when the pll fails to lock. Remove the pll_u clocks from the init_table so that software does not try to configure this pll on boot.
--- drivers/clk/tegra/clk-tegra210.c | 2 -- 1 file changed, 2 deletions(-)
drivers/clk/tegra/clk-tegra210.c +0 -2
@@ -2739,8 +2739,6 @@ static struct tegra_clk_init_table init_table[] __initdata = { { TEGRA210_CLK_DFLL_REF, TEGRA210_CLK_PLL_P, 51000000, 1 }, { TEGRA210_CLK_SBC4, TEGRA210_CLK_PLL_P, 12000000, 1 }, { TEGRA210_CLK_PLL_RE_VCO, TEGRA210_CLK_CLK_MAX, 672000000, 1 }, - { TEGRA210_CLK_PLL_U_OUT1, TEGRA210_CLK_CLK_MAX, 48000000, 1 }, - { TEGRA210_CLK_PLL_U_OUT2, TEGRA210_CLK_CLK_MAX, 60000000, 1 }, { TEGRA210_CLK_XUSB_GATE, TEGRA210_CLK_CLK_MAX, 0, 1 }, { TEGRA210_CLK_XUSB_SS_SRC, TEGRA210_CLK_PLL_U_480M, 120000000, 0 }, { TEGRA210_CLK_XUSB_FS_SRC, TEGRA210_CLK_PLL_U_48M, 48000000, 0 },
Signature · 1 line
2.1.4
Jon Hunter
maintainerPATCH 2/2 clk: tegra: Use definition for pll_u override bit
The definition, PLLU_BASE_OVERRIDE, for the pll_u OVERRIDE bit is defined but not used and when the OVERRIDE bit is cleared in tegra210_pll_init() the code directly uses the bit number. Therefore, use the definition, PLLU_BASE_OVERRIDE when clearing the OVERRIDE bit.
--- drivers/clk/tegra/clk-tegra210.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/tegra/clk-tegra210.c +1 -1
@@ -2520,7 +2520,7 @@ static void __init tegra210_pll_init(void __iomem *clk_base,/* PLLU_VCO */ val =readl (clk_base + pll_u_vco_params.base_reg); - val &= ~BIT (24 );/* disable PLLU_OVERRIDE */ + val &= ~PLLU_BASE_OVERRIDE ;/* disable PLLU_OVERRIDE */ writel (val, clk_base + pll_u_vco_params.base_reg); clk = tegra_clk_register_pllre("pll_u_vco", "pll_ref", clk_base, pmc,
Signature · 1 line
2.1.4
Re: [PATCH 2/2] clk: tegra: Use definition for pll_u override bit
Quoted 16 lines · Jon Hunter
The definition,
PLLU_BASE_OVERRIDE, for thepll_uOVERRIDE bit is defined but not used and when the OVERRIDE bit is cleared integra210_pll_init()the code directly uses the bit number. Therefore, use the definition,PLLU_BASE_OVERRIDEwhen clearing the OVERRIDE bit.Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/clk/tegra/clk-tegra210.c +0
-0
drivers/clk/tegra/clk-tegra210.c static void __init tegra210_pll_init(void __iomem *clk_base, · line 2526
Quoted 8 lines
drivers/clk/tegra/clk-tegra210.c +1
-1@@ -2520,7 +2520,7 @@ static void __init tegra210_pll_init(void __iomem *clk_base,/* PLLU_VCO */ val =readl (clk_base + pll_u_vco_params.base_reg); - val &= ~BIT (24 );/* disable PLLU_OVERRIDE */ + val &= ~PLLU_BASE_OVERRIDE ;/* disable PLLU_OVERRIDE */ writel (val, clk_base + pll_u_vco_params.base_reg); clk = tegra_clk_register_pllre("pll_u_vco", "pll_ref", clk_base, pmc,
Signature · 1 line
nvpublic
Re: [PATCH 2/2] clk: tegra: Use definition for pll_u override bit
In reply to Jon HunterQuoted 15 lines · Jon Hunter
The definition,
PLLU_BASE_OVERRIDE, for thepll_uOVERRIDE bit is defined but not used and when the OVERRIDE bit is cleared integra210_pll_init()the code directly uses the bit number. Therefore, use the definition,PLLU_BASE_OVERRIDEwhen clearing the OVERRIDE bit.Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/clk/tegra/clk-tegra210.c +0
-0
drivers/clk/tegra/clk-tegra210.c static void __init tegra210_pll_init(void __iomem *clk_base, · line 2526
Quoted 8 lines
drivers/clk/tegra/clk-tegra210.c +1
-1@@ -2520,7 +2520,7 @@ static void __init tegra210_pll_init(void __iomem *clk_base,/* PLLU_VCO */ val =readl (clk_base + pll_u_vco_params.base_reg); - val &= ~BIT (24 );/* disable PLLU_OVERRIDE */ + val &= ~PLLU_BASE_OVERRIDE ;/* disable PLLU_OVERRIDE */ writel (val, clk_base + pll_u_vco_params.base_reg); clk = tegra_clk_register_pllre("pll_u_vco", "pll_ref", clk_base, pmc,
I think the comment is now redundant, given that the code says pretty much the same thing. No need to respin for that, I can remove the comment when I apply the patch. That is, unless anyone feels strongly about keeping the comment.
Thierry
Re: [PATCH 2/2] clk: tegra: Use definition for pll_u override bit
Quoted 25 lines · Thierry Reding
* PGP Signed by an unknown key
Quoted 22 lines · Jon Hunter
The definition,
PLLU_BASE_OVERRIDE, for thepll_uOVERRIDE bit is defined but not used and when the OVERRIDE bit is cleared integra210_pll_init()the code directly uses the bit number. Therefore, use the definition,PLLU_BASE_OVERRIDEwhen clearing the OVERRIDE bit.Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/clk/tegra/clk-tegra210.c +1
-1@@ -2520,7 +2520,7 @@ static void __init tegra210_pll_init(void __iomem *clk_base,/* PLLU_VCO */ val =readl (clk_base + pll_u_vco_params.base_reg); - val &= ~BIT (24 );/* disable PLLU_OVERRIDE */ + val &= ~PLLU_BASE_OVERRIDE ;/* disable PLLU_OVERRIDE */ writel (val, clk_base + pll_u_vco_params.base_reg);
Quoted 6 lines
drivers/clk/tegra/clk-tegra210.c static void __init tegra210_pll_init(void __iomem *clk_base, · line 2526
Quoted 1 line
drivers/clk/tegra/clk-tegra210.c +0
-0clk = tegra_clk_register_pllre("pll_u_vco", "pll_ref", clk_base, pmc,I think the comment is now redundant, given that the code says pretty much the same thing. No need to respin for that, I can remove the comment when I apply the patch. That is, unless anyone feels strongly about keeping the comment.
I agree its redundant. If I am going to post a new version to address other concerns, I can just roll this in while doing so.
-rhyland
Signature · 1 line
nvpublic
Re: [PATCH 2/2] clk: tegra: Use definition for pll_u override bit
Quoted 33 lines · Rhyland Klein
Quoted 25 lines · Thierry Reding
* PGP Signed by an unknown key
Quoted 22 lines · Jon Hunter
The definition,
PLLU_BASE_OVERRIDE, for thepll_uOVERRIDE bit is defined but not used and when the OVERRIDE bit is cleared integra210_pll_init()the code directly uses the bit number. Therefore, use the definition,PLLU_BASE_OVERRIDEwhen clearing the OVERRIDE bit.Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/clk/tegra/clk-tegra210.c +1
-1@@ -2520,7 +2520,7 @@ static void __init tegra210_pll_init(void __iomem *clk_base,/* PLLU_VCO */ val =readl (clk_base + pll_u_vco_params.base_reg); - val &= ~BIT (24 );/* disable PLLU_OVERRIDE */ + val &= ~PLLU_BASE_OVERRIDE ;/* disable PLLU_OVERRIDE */ writel (val, clk_base + pll_u_vco_params.base_reg);Quoted 6 lines
drivers/clk/tegra/clk-tegra210.c static void __init tegra210_pll_init(void __iomem *clk_base, · line 2526
Quoted 1 line
drivers/clk/tegra/clk-tegra210.c +0
-0clk = tegra_clk_register_pllre("pll_u_vco", "pll_ref", clk_base, pmc,I think the comment is now redundant, given that the code says pretty much the same thing. No need to respin for that, I can remove the comment when I apply the patch. That is, unless anyone feels strongly about keeping the comment.
Quoted 2 lines
I agree its redundant. If I am going to post a new version to address other concerns, I can just roll this in while doing so.
This looks like a good fix, or cleanup, on its own. So no need for anyone to carry this forward, I can pick it up into a fixes branch for v4.5.
Thierry
Re: [PATCH 2/2] clk: tegra: Use definition for pll_u override bit
Quoted 36 lines · Thierry Reding
* PGP Signed by an unknown key
Quoted 33 lines · Rhyland Klein
Quoted 31 lines · Thierry Reding
Quoted 1 line
Old Signed by an unknown key
Quoted 15 lines · Jon Hunter
The definition,
PLLU_BASE_OVERRIDE, for thepll_uOVERRIDE bit is defined but not used and when the OVERRIDE bit is cleared integra210_pll_init()the code directly uses the bit number. Therefore, use the definition,PLLU_BASE_OVERRIDEwhen clearing the OVERRIDE bit.Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/clk/tegra/clk-tegra210.c +0
-0drivers/clk/tegra/clk-tegra210.c static void __init tegra210_pll_init(void __iomem *clk_base, · line 2526
Quoted 8 lines
drivers/clk/tegra/clk-tegra210.c +1
-1@@ -2520,7 +2520,7 @@ static void __init tegra210_pll_init(void __iomem *clk_base,/* PLLU_VCO */ val =readl (clk_base + pll_u_vco_params.base_reg); - val &= ~BIT (24 );/* disable PLLU_OVERRIDE */ + val &= ~PLLU_BASE_OVERRIDE ;/* disable PLLU_OVERRIDE */ writel (val, clk_base + pll_u_vco_params.base_reg); clk = tegra_clk_register_pllre("pll_u_vco", "pll_ref", clk_base, pmc,I think the comment is now redundant, given that the code says pretty much the same thing. No need to respin for that, I can remove the comment when I apply the patch. That is, unless anyone feels strongly about keeping the comment.
Quoted 7 lines
Quoted 2 lines
I agree its redundant. If I am going to post a new version to address other concerns, I can just roll this in while doing so.
This looks like a good fix, or cleanup, on its own. So no need for anyone to carry this forward, I can pick it up into a fixes branch for v4.5.
Sure thing.
Thanks,
Rhyland
Signature · 1 line
nvpublic
Jon Hunter
maintainerRe: [PATCH 2/2] clk: tegra: Use definition for pll_u override bit
In reply to Thierry RedingQuoted 25 lines · Thierry Reding
* PGP Signed by an unknown key
Quoted 22 lines · Jon Hunter
The definition,
PLLU_BASE_OVERRIDE, for thepll_uOVERRIDE bit is defined but not used and when the OVERRIDE bit is cleared integra210_pll_init()the code directly uses the bit number. Therefore, use the definition,PLLU_BASE_OVERRIDEwhen clearing the OVERRIDE bit.Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/clk/tegra/clk-tegra210.c +1
-1@@ -2520,7 +2520,7 @@ static void __init tegra210_pll_init(void __iomem *clk_base,/* PLLU_VCO */ val =readl (clk_base + pll_u_vco_params.base_reg); - val &= ~BIT (24 );/* disable PLLU_OVERRIDE */ + val &= ~PLLU_BASE_OVERRIDE ;/* disable PLLU_OVERRIDE */ writel (val, clk_base + pll_u_vco_params.base_reg);
Quoted 6 lines
drivers/clk/tegra/clk-tegra210.c static void __init tegra210_pll_init(void __iomem *clk_base, · line 2526
Quoted 1 line
drivers/clk/tegra/clk-tegra210.c +0
-0clk = tegra_clk_register_pllre("pll_u_vco", "pll_ref", clk_base, pmc,I think the comment is now redundant, given that the code says pretty much the same thing. No need to respin for that, I can remove the comment when I apply the patch. That is, unless anyone feels strongly about keeping the comment.
Fine with me. Thanks.
Jon
Re: [PATCH 2/2] clk: tegra: Use definition for pll_u override bit
In reply to Jon HunterQuoted 9 lines · Jon Hunter
The definition,
PLLU_BASE_OVERRIDE, for thepll_uOVERRIDE bit is defined but not used and when the OVERRIDE bit is cleared integra210_pll_init()the code directly uses the bit number. Therefore, use the definition,PLLU_BASE_OVERRIDEwhen clearing the OVERRIDE bit.Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Applied with the now redundant comment removed.
Thanks,
Thierry
Quoted 66 lines · Jon Hunter
If the
pll_uis not configured by the bootloader, then on kernel boot the following warning is seen:
clk_pll_wait_for_lock: Timed out waiting for pllpll_u_vcolock
tegra_init_from_table: Failed to enablepll_u_out1------------[ cut here ]------------ WARNING: at drivers/clk/tegra/clk.c:269 Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc4-next-20151214+ #1 Hardware name: NVIDIA Tegra210 P2371 reference board (E.1) (DT) task: ffffffc0bc0a0000 ti: ffffffc0bc0a8000 task.ti: ffffffc0bc0a8000 PC is at tegra_init_from_table+0x140/0x164 LR is at tegra_init_from_table+0x140/0x164 pc : [<ffffffc0008fee78>] lr : [<ffffffc0008fee78>] pstate: 80000045 sp : ffffffc0bc0abd50 x29: ffffffc0bc0abd50 x28: ffffffc00090b8a8 x27: ffffffc000a06000 x26: ffffffc0bc019780 x25: ffffffc00086a708 x24: ffffffc00086a790 x23: ffffffc0006d7188 x22: ffffffc0bc010000 x21: 000000000000016e x20: ffffffc0bc00d100 x19: ffffffc000944178 x18: 0000000000000007 x17: 000000000000000e x16: 0000000000000001 x15: 0000000000000007 x14: 000000000000000e x13: 0000000000000013 x12: 000000000000001a x11: 000000000000004d x10: 0000000000000750 x9 : ffffffc0bc0a8000 x8 : ffffffc0bc0a07b0 x7 : 0000000000000001 x6 : 0000000002d5f0f8 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000002 x2 : ffffffc000996724 x1 : 0000000000000000 x0 : 0000000000000032 ---[ end trace cbd20ae519e92ced ]--- Call trace: [<ffffffc0008fee78>] tegra_init_from_table+0x140/0x164 [<ffffffc000900ac8>] tegra210_clock_apply_init_table+0x20/0x28 [<ffffffc0008fec40>] tegra_clocks_apply_init_table+0x18/0x24 [<ffffffc00008291c>] do_one_initcall+0x90/0x194 [<ffffffc0008cfab0>] kernel_init_freeable+0x148/0x1e8 [<ffffffc000636bb0>] kernel_init+0x10/0xdc [<ffffffc000085cd0>] ret_from_fork+0x10/0x40 clk_pll_wait_for_lock: Timed out waiting for pll pll_u_vco lock tegra_init_from_table: Failed to enable pll_u_out2 ------------[ cut here ]------------
pll_ucan be either controlled by software or hardware and this is selected via the OVERRIDE bit in thepll_ubase register. In the functiontegra210_pll_init(), the OVERRIDE bit forpll_uis cleared, which selects hardware control of the pll. However, at the same time thepll_uclocks are populated in theinit_tablefor tegra210 and so software will try to configure thepll_uif it is not already configured and hence, the above warning is seen when the pll fails to lock. Remove thepll_uclocks from theinit_tableso that software does not try to configure this pll on boot.Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 -- 1 file changed, 2 deletions(-)drivers/clk/tegra/clk-tegra210.c +0
-0
drivers/clk/tegra/clk-tegra210.c static struct tegra_clk_init_table init_table[] __initdata = { · line 2744
Quoted 8 lines
drivers/clk/tegra/clk-tegra210.c +0
-2@@ -2739,8 +2739,6 @@ static struct tegra_clk_init_table init_table[] __initdata = { { TEGRA210_CLK_DFLL_REF, TEGRA210_CLK_PLL_P, 51000000, 1 }, { TEGRA210_CLK_SBC4, TEGRA210_CLK_PLL_P, 12000000, 1 }, { TEGRA210_CLK_PLL_RE_VCO, TEGRA210_CLK_CLK_MAX, 672000000, 1 }, - { TEGRA210_CLK_PLL_U_OUT1, TEGRA210_CLK_CLK_MAX, 48000000, 1 }, - { TEGRA210_CLK_PLL_U_OUT2, TEGRA210_CLK_CLK_MAX, 60000000, 1 }, { TEGRA210_CLK_XUSB_GATE, TEGRA210_CLK_CLK_MAX, 0, 1 }, { TEGRA210_CLK_XUSB_SS_SRC, TEGRA210_CLK_PLL_U_480M, 120000000, 0 }, { TEGRA210_CLK_XUSB_FS_SRC, TEGRA210_CLK_PLL_U_48M, 48000000, 0 },
Signature · 1 line
nvpublic
Thierry Reding
AppliedQuoted 55 lines · Jon Hunter
If the
pll_uis not configured by the bootloader, then on kernel boot the following warning is seen:
clk_pll_wait_for_lock: Timed out waiting for pllpll_u_vcolock
tegra_init_from_table: Failed to enablepll_u_out1------------[ cut here ]------------ WARNING: at drivers/clk/tegra/clk.c:269 Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc4-next-20151214+ #1 Hardware name: NVIDIA Tegra210 P2371 reference board (E.1) (DT) task: ffffffc0bc0a0000 ti: ffffffc0bc0a8000 task.ti: ffffffc0bc0a8000 PC is at tegra_init_from_table+0x140/0x164 LR is at tegra_init_from_table+0x140/0x164 pc : [<ffffffc0008fee78>] lr : [<ffffffc0008fee78>] pstate: 80000045 sp : ffffffc0bc0abd50 x29: ffffffc0bc0abd50 x28: ffffffc00090b8a8 x27: ffffffc000a06000 x26: ffffffc0bc019780 x25: ffffffc00086a708 x24: ffffffc00086a790 x23: ffffffc0006d7188 x22: ffffffc0bc010000 x21: 000000000000016e x20: ffffffc0bc00d100 x19: ffffffc000944178 x18: 0000000000000007 x17: 000000000000000e x16: 0000000000000001 x15: 0000000000000007 x14: 000000000000000e x13: 0000000000000013 x12: 000000000000001a x11: 000000000000004d x10: 0000000000000750 x9 : ffffffc0bc0a8000 x8 : ffffffc0bc0a07b0 x7 : 0000000000000001 x6 : 0000000002d5f0f8 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000002 x2 : ffffffc000996724 x1 : 0000000000000000 x0 : 0000000000000032 ---[ end trace cbd20ae519e92ced ]--- Call trace: [<ffffffc0008fee78>] tegra_init_from_table+0x140/0x164 [<ffffffc000900ac8>] tegra210_clock_apply_init_table+0x20/0x28 [<ffffffc0008fec40>] tegra_clocks_apply_init_table+0x18/0x24 [<ffffffc00008291c>] do_one_initcall+0x90/0x194 [<ffffffc0008cfab0>] kernel_init_freeable+0x148/0x1e8 [<ffffffc000636bb0>] kernel_init+0x10/0xdc [<ffffffc000085cd0>] ret_from_fork+0x10/0x40 clk_pll_wait_for_lock: Timed out waiting for pll pll_u_vco lock tegra_init_from_table: Failed to enable pll_u_out2 ------------[ cut here ]------------
pll_ucan be either controlled by software or hardware and this is selected via the OVERRIDE bit in thepll_ubase register. In the functiontegra210_pll_init(), the OVERRIDE bit forpll_uis cleared, which selects hardware control of the pll. However, at the same time thepll_uclocks are populated in theinit_tablefor tegra210 and so software will try to configure thepll_uif it is not already configured and hence, the above warning is seen when the pll fails to lock. Remove thepll_uclocks from theinit_tableso that software does not try to configure this pll on boot.
Quoted 4 lines
Signed-off-by Jon Hunter <[email protected]>--- drivers/clk/tegra/clk-tegra210.c | 2 -- 1 file changed, 2 deletions(-)
Applied, thanks.
Thierry