ARM: BCM5301X: Add DT for D-Link DIR-885L

---
 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/bcm47094-dlink-885l.dts | 112 ++++++++++++++++++++++++++++++
 2 files changed, 113 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-dlink-885l.dts

index eab8a7f..bf9c185 100644
@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-buffalo-wxr-1900dhp.dtb \
 	bcm4709-netgear-r7000.dtb \
 	bcm4709-netgear-r8000.dtb \
+	bcm47094-dlink-885l.dtb \
 	bcm94708.dtb \
 	bcm94709.dtb \
 	bcm953012k.dtb

1.8.4.5

---
V2: Include "dir-" in filename.

---
 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 112 ++++++++++++++++++++++++++
 2 files changed, 113 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts

index eab8a7f..d7fcd46 100644
@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-buffalo-wxr-1900dhp.dtb \
 	bcm4709-netgear-r7000.dtb \
 	bcm4709-netgear-r8000.dtb \
+	bcm47094-dlink-dir-885l.dtb \
 	bcm94708.dtb \
 	bcm94709.dtb \
 	bcm953012k.dtb

1.8.4.5

It would be nice to have a more descriptive commit message which describes what you are doing here, like amount of memory, buttons/LEDs etc.

Thanks!

Florian

It's device based on BCM47094 which is quite similar to BCM4709 except for higher CPU frequency. This device has 2 flash memories, it boots from serial one and stores firmware on NAND. Other than that we define standard stuff like LEDs, buttons and UART.

---
V2: Include "dir-" in filename.
V3: Commit message
Drop "earlyprintk" (which is unwanted, we should switch to earlycon) Define lowmem only (like on all other devices), we still miss swiotlb

---
 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 111 ++++++++++++++++++++++++++
 2 files changed, 112 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts

index eab8a7f..d7fcd46 100644
@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-buffalo-wxr-1900dhp.dtb \
 	bcm4709-netgear-r7000.dtb \
 	bcm4709-netgear-r8000.dtb \
+	bcm47094-dlink-dir-885l.dtb \
 	bcm94708.dtb \
 	bcm94709.dtb \
 	bcm953012k.dtb

1.8.4.5

Applied to devicetree/next, thanks!

Florian