board: atmel: sama5d2_xplained: add SPL support

The sama5d2 Xplained SPL supports the boot medias: spi flash and SD Card.

Signed-off-by Wenyou Yang <[email protected]>

---
This patch is base on [U-Boot] [PATCH v3 0/3] arm: at91/spl: add DDR3-SDRAM initialization support

	http://lists.denx.de/pipermail/u-boot/2016-February/244228.html

Changes in v2:
- adapt to ddr3_init() declaration variation.

 arch/arm/mach-at91/Kconfig                      |    1 +
 arch/arm/mach-at91/Makefile                     |    1 +
 arch/arm/mach-at91/include/mach/sama5d2.h       |   32 +++++++
 board/atmel/sama5d2_xplained/sama5d2_xplained.c |  103 +++++++++++++++++++++++
 configs/sama5d2_xplained_mmc_defconfig          |    1 +
 configs/sama5d2_xplained_spiflash_defconfig     |    1 +
 include/configs/sama5d2_xplained.h              |   39 +++++++++
 7 files changed, 178 insertions(+)

arch/arm/mach-at91/Kconfig +1 -0

index c333647..9426302b 100644
@@ -74,6 +74,7 @@ config TARGET_AT91SAM9X5EK
 config TARGET_SAMA5D2_XPLAINED
 	bool "SAMA5D2 Xplained board"
 	select CPU_V7
+	select SUPPORT_SPL
 
 config TARGET_SAMA5D3_XPLAINED
 	bool "SAMA5D3 Xplained board"

arch/arm/mach-at91/Makefile +1 -0

index 5b89617..abd1d13 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_AT91SAM9G20) += sdram.o spl_at91.o
 obj-$(CONFIG_AT91SAM9M10G45) += mpddrc.o spl_at91.o
 obj-$(CONFIG_AT91SAM9N12) += mpddrc.o spl_at91.o
 obj-$(CONFIG_AT91SAM9X5) += mpddrc.o spl_at91.o
+obj-$(CONFIG_SAMA5D2) += mpddrc.o spl_atmel.o matrix.o atmel_sfr.o
 obj-$(CONFIG_SAMA5D3) += mpddrc.o spl_atmel.o
 obj-$(CONFIG_SAMA5D4) += mpddrc.o spl_atmel.o matrix.o atmel_sfr.o
 obj-y += spl.o

arch/arm/mach-at91/include/mach/sama5d2.h +32 -0

index c85571c..dd5a2a7 100644
@@ -106,6 +106,7 @@
 #define ATMEL_BASE_MPDDRC	0xf000c000
 #define ATMEL_BASE_XDMAC0	0xf0010000
 #define ATMEL_BASE_PMC		0xf0014000
+#define ATMEL_BASE_MATRIX0	0xf0018000
 #define ATMEL_BASE_QSPI0	0xf0020000
 #define ATMEL_BASE_QSPI1	0xf0024000
 #define ATMEL_BASE_SPI0		0xf8000000

@@ -117,6 +118,7 @@
 #define ATMEL_BASE_UART1	0xf8020000
 #define ATMEL_BASE_UART2	0xf8024000
 #define ATMEL_BASE_TWI0		0xf8028000
+#define ATMEL_BASE_SFR		0xf8030000
 #define ATMEL_BASE_SYSC		0xf8048000
 #define ATMEL_BASE_SPI1		0xfc000000
 #define ATMEL_BASE_UART3	0xfc008000

@@ -125,6 +127,7 @@
 #define ATMEL_BASE_UDPHS	0xfc02c000
 
 #define ATMEL_BASE_PIOA		0xfc038000
+#define ATMEL_BASE_MATRIX1	0xfc03c000
 
 #define ATMEL_CHIPID_CIDR	0xfc069000
 #define ATMEL_CHIPID_EXID	0xfc069004

@@ -171,6 +174,35 @@
 #define CPU_HAS_PCR
 #define CPU_HAS_H32MXDIV
 
+/* AICREDIR Unlock Key */
+#define ATMEL_SFR_AICREDIR_KEY		0xB6D81C4D
+
+/* MATRIX0(H64MX) slave id definitions */
+#define H64MX_SLAVE_AXIMX_BRIDGE	0	/* Bridge from H64MX to AXIMX */
+#define H64MX_SLAVE_PERIPH_BRIDGE	1	/* H64MX Peripheral Bridge */
+#define H64MX_SLAVE_DDRC_PORT0		2	/* DDR2 Port0-AESOTF */
+#define H64MX_SLAVE_DDRC_PORT1		3	/* DDR2 Port1 */
+#define H64MX_SLAVE_DDRC_PORT2		4	/* DDR2 Port2 */
+#define H64MX_SLAVE_DDRC_PORT3		5	/* DDR2 Port3 */
+#define H64MX_SLAVE_DDRC_PORT4		6	/* DDR2 Port4 */
+#define H64MX_SLAVE_DDRC_PORT5		7	/* DDR2 Port5 */
+#define H64MX_SLAVE_DDRC_PORT6		8	/* DDR2 Port6 */
+#define H64MX_SLAVE_DDRC_PORT7		9	/* DDR2 Port7 */
+#define H64MX_SLAVE_SRAM		10	/* Internal SRAM 128K */
+#define H64MX_SLAVE_CACHE_L2		11	/* Internal SRAM 128K(L2) */
+#define H64MX_SLAVE_QSPI0		12	/* QSPI0 */
+#define H64MX_SLAVE_QSPI1		13	/* QSPI1 */
+#define H64MX_SLAVE_AESB		14	/* AESB */
+
+/* MATRIX1(H32MX) slave id definitions */
+#define H32MX_SLAVE_H64MX_BRIDGE	0	/* Bridge from H32MX to H64MX */
+#define H32MX_SLAVE_PERIPH_BRIDGE0	1	/* H32MX Peripheral Bridge 0 */
+#define H32MX_SLAVE_PERIPH_BRIDGE1	2	/* H32MX Peripheral Bridge 1 */
+#define H32MX_SLAVE_EBI			3	/* External Bus Interface */
+#define H32MX_SLAVE_NFC_CMD		3	/* NFC command Register */
+#define H32MX_SLAVE_NFC_SRAM		4	/* NFC SRAM */
+#define H32MX_SLAVE_USB			5	/* USB Device & Host */
+
 /* SAMA5D2 series chip id definitions */
 #define ARCH_ID_SAMA5D2		0x8a5c08c0
 #define ARCH_EXID_SAMA5D21CU	0x0000005a

board/atmel/sama5d2_xplained/sama5d2_xplained.c +103 -0

index 0b3397f..8ed01dd 100644
@@ -17,6 +17,7 @@
 #include <asm/arch/at91_common.h>
 #include <asm/arch/at91_pmc.h>
 #include <asm/arch/atmel_pio4.h>
+#include <asm/arch/atmel_mpddrc.h>
 #include <asm/arch/atmel_usba_udc.h>
 #include <asm/arch/atmel_sdhci.h>
 #include <asm/arch/clk.h>

@@ -281,3 +282,105 @@ int board_eth_init(bd_t *bis)
 
 	return rc;
 }
+
+/* SPL */
+#ifdef CONFIG_SPL_BUILD
+void spl_board_init(void)
+{
+#ifdef CONFIG_SYS_USE_SERIALFLASH
+	board_spi0_hw_init();
+#endif
+#ifdef CONFIG_ATMEL_SDHCI
+#ifdef CONFIG_ATMEL_SDHCI0
+	board_sdhci0_hw_init();
+#endif
+#ifdef CONFIG_ATMEL_SDHCI1
+	board_sdhci1_hw_init();
+#endif
+#endif
+}
+
+static void ddrc_conf(struct atmel_mpddrc_config *ddrc)
+{
+	ddrc->md = (ATMEL_MPDDRC_MD_DBW_32_BITS | ATMEL_MPDDRC_MD_DDR3_SDRAM);
+
+	ddrc->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+		    ATMEL_MPDDRC_CR_NR_ROW_14 |
+		    ATMEL_MPDDRC_CR_CAS_DDR_CAS5 |
+		    ATMEL_MPDDRC_CR_DIC_DS |
+		    ATMEL_MPDDRC_CR_DIS_DLL |
+		    ATMEL_MPDDRC_CR_NB_8BANKS |
+		    ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
+		    ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
+
+	ddrc->rtr = 0x511;
+
+	ddrc->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
+		      3 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
+		      4 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
+		      9 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
+		      3 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
+		      4 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
+		      4 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
+		      4 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
+
+	ddrc->tpr1 = (27 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET |
+		      29 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+		      0 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+		      3 << ATMEL_MPDDRC_TPR1_TXP_OFFSET);
+
+	ddrc->tpr2 = (0 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET |
+		      0 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+		      0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+		      4 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+		      7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET);
+}
+
+void mem_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	struct atmel_mpddr *mpddrc = (struct atmel_mpddr *)ATMEL_BASE_MPDDRC;
+	struct atmel_mpddrc_config ddrc_config;
+	u32 reg;
+
+	ddrc_conf(&ddrc_config);
+
+	at91_periph_clk_enable(ATMEL_ID_MPDDRC);
+	writel(AT91_PMC_DDR, &pmc->scer);
+
+	reg = readl(&mpddrc->io_calibr);
+	reg &= ~ATMEL_MPDDRC_IO_CALIBR_RDIV;
+	reg |= ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_55;
+	reg &= ~ATMEL_MPDDRC_IO_CALIBR_TZQIO;
+	reg |= ATMEL_MPDDRC_IO_CALIBR_TZQIO_(100);
+	writel(reg, &mpddrc->io_calibr);
+
+	writel(ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_TWO_CYCLE,
+	       &mpddrc->rd_data_path);
+
+	ddr3_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddrc_config);
+
+	writel(0x3, &mpddrc->cal_mr4);
+	writel(64, &mpddrc->tim_cal);
+}
+
+void at91_pmc_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	u32 tmp;
+
+	tmp = AT91_PMC_PLLAR_29 |
+	      AT91_PMC_PLLXR_PLLCOUNT(0x3f) |
+	      AT91_PMC_PLLXR_MUL(82) |
+	      AT91_PMC_PLLXR_DIV(1);
+	at91_plla_init(tmp);
+
+	writel(0x0 << 8, &pmc->pllicpr);
+
+	tmp = AT91_PMC_MCKR_H32MXDIV |
+	      AT91_PMC_MCKR_PLLADIV_2 |
+	      AT91_PMC_MCKR_MDIV_3 |
+	      AT91_PMC_MCKR_CSS_PLLA;
+	at91_mck_init(tmp);
+}
+#endif

configs/sama5d2_xplained_mmc_defconfig +1 -0

index c1dcbef..75b1713 100644
@@ -1,6 +1,7 @@
 CONFIG_ARM=y
 CONFIG_ARCH_AT91=y
 CONFIG_TARGET_SAMA5D2_XPLAINED=y
+CONFIG_SPL=y
 CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
 # CONFIG_CMD_IMI is not set
 # CONFIG_CMD_IMLS is not set

configs/sama5d2_xplained_spiflash_defconfig +1 -0

index 0271e8e..6d61a7e 100644
@@ -1,6 +1,7 @@
 CONFIG_ARM=y
 CONFIG_ARCH_AT91=y
 CONFIG_TARGET_SAMA5D2_XPLAINED=y
+CONFIG_SPL=y
 CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_SERIALFLASH"
 # CONFIG_CMD_IMI is not set
 # CONFIG_CMD_IMLS is not set

include/configs/sama5d2_xplained.h +39 -0

index ae5ba3d..272257e 100644
@@ -25,8 +25,12 @@
 #define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
 #define CONFIG_SYS_SDRAM_SIZE		0x20000000
 
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_INIT_SP_ADDR		0x210000
+#else
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+#endif
 
 #define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */
 

@@ -119,4 +123,39 @@
 
 #endif
 
+/* SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE		0x200000
+#define CONFIG_SPL_MAX_SIZE		0x10000
+#define CONFIG_SPL_BSS_START_ADDR	0x20000000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x80000
+#define CONFIG_SYS_SPL_MALLOC_START	0x20080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x80000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SYS_MONITOR_LEN		(512 << 10)
+
+#ifdef CONFIG_SYS_USE_MMC
+#define CONFIG_SPL_LDSCRIPT		arch/arm/mach-at91/armv7/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#elif CONFIG_SYS_USE_SERIALFLASH
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x8000
+
+#endif
+
 #endif

The sama5d2 Xplained SPL supports the boot medias: spi flash and SD Card.

Signed-off-by Wenyou Yang <[email protected]>

Reviewed-by Andreas Bie?mann <[email protected]>

---
This patch is base on [U-Boot] [PATCH v3 0/3] arm: at91/spl: add DDR3-SDRAM initialization support

	http://lists.denx.de/pipermail/u-boot/2016-February/244228.html

Changes in v2:
- adapt to ddr3_init() declaration variation.

arch/arm/mach-at91/Kconfig                      |    1 +
arch/arm/mach-at91/Makefile                     |    1 +
arch/arm/mach-at91/include/mach/sama5d2.h       |   32 +++++++
board/atmel/sama5d2_xplained/sama5d2_xplained.c |  103 +++++++++++++++++++++++
configs/sama5d2_xplained_mmc_defconfig          |    1 +
configs/sama5d2_xplained_spiflash_defconfig     |    1 +
include/configs/sama5d2_xplained.h              |   39 +++++++++
7 files changed, 178 insertions(+)