arm: mx6: Add UART8 base address for i.MX6UL

This patch add support for the CCV xPress board which is equipped with the i.MX6UL. And provides the following interfaces:

- 128MiB DDR
- UART
- I2C
- eMMC (with booting)
- Ethernet
- USB

This patch adds two build targets. One with and one without SPL. The non-SPL version is used for loading U-Boot via USB (imx_usb_loader).

Signed-off-by Stefan Roese <[email protected]>

Cc Fabio Estevam <[email protected]>

Cc Stefano Babic <[email protected]>

---
 arch/arm/cpu/armv7/mx6/Kconfig |   8 +
 board/ccv/xpress/Kconfig       |  12 ++
 board/ccv/xpress/MAINTAINERS   |   7 +
 board/ccv/xpress/Makefile      |   8 +
 board/ccv/xpress/imximage.cfg  | 176 ++++++++++++++++++++++
 board/ccv/xpress/spl.c         | 116 +++++++++++++++
 board/ccv/xpress/xpress.c      | 331 +++++++++++++++++++++++++++++++++++++++++
 configs/xpress_defconfig       |   6 +
 configs/xpress_spl_defconfig   |   7 +
 include/configs/xpress.h       | 166 +++++++++++++++++++++
 10 files changed, 837 insertions(+)
 create mode 100644 board/ccv/xpress/Kconfig
 create mode 100644 board/ccv/xpress/MAINTAINERS
 create mode 100644 board/ccv/xpress/Makefile
 create mode 100644 board/ccv/xpress/imximage.cfg
 create mode 100644 board/ccv/xpress/spl.c
 create mode 100644 board/ccv/xpress/xpress.c
 create mode 100644 configs/xpress_defconfig
 create mode 100644 configs/xpress_spl_defconfig
 create mode 100644 include/configs/xpress.h

arch/arm/cpu/armv7/mx6/Kconfig +8 -0

index c72a150..f5e62a7 100644
@@ -153,6 +153,13 @@ config TARGET_WANDBOARD
 config TARGET_WARP
 	bool "WaRP"
 
+config TARGET_XPRESS
+	bool "CCV xPress"
+	select MX6UL
+	select DM
+	select DM_THERMAL
+	select SUPPORT_SPL
+
 endchoice
 
 config SYS_SOC

@@ -163,6 +170,7 @@ source "board/bachmann/ot1200/Kconfig"
 source "board/barco/platinum/Kconfig"
 source "board/barco/titanium/Kconfig"
 source "board/boundary/nitrogen6x/Kconfig"
+source "board/ccv/xpress/Kconfig"
 source "board/compulab/cm_fx6/Kconfig"
 source "board/congatec/cgtqmx6eval/Kconfig"
 source "board/embest/mx6boards/Kconfig"

board/ccv/xpress/Kconfig new file +12 -0

new file mode 100644
index 0000000..9157013
@@ -0,0 +1,12 @@
+if TARGET_XPRESS
+
+config SYS_BOARD
+	default "xpress"
+
+config SYS_VENDOR
+	default "ccv"
+
+config SYS_CONFIG_NAME
+	default "xpress"
+
+endif

board/ccv/xpress/MAINTAINERS new file +7 -0

new file mode 100644
index 0000000..e242bfb
@@ -0,0 +1,7 @@
+CCV XPRESS BOARD
+M:	Stefan Roese <[email protected]>
+S:	Maintained
+F:	board/ccv/xpress/
+F:	include/configs/xpress.h
+F:	configs/xpress_defconfig
+F:	configs/xpress_spl_defconfig

board/ccv/xpress/Makefile new file +8 -0

new file mode 100644
index 0000000..0d444b6
@@ -0,0 +1,8 @@
+#
+# Copyright (C) 2015-2016 Stefan Roese <[email protected]>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := xpress.o
+obj-$(CONFIG_SPL_BUILD) += spl.o

board/ccv/xpress/imximage.cfg new file +176 -0

new file mode 100644
index 0000000..92167c9
@@ -0,0 +1,176 @@
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * sd, nand
+ */
+BOOT_FROM      sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *      Addr-type register length (1,2 or 4 bytes)
+ *      Address   absolute address of the register
+ *      value     value to be stored in the register
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* Enable all clocks */
+DATA 4 0x020c4068 0xffffffff
+DATA 4 0x020c406c 0xffffffff
+DATA 4 0x020c4070 0xffffffff
+DATA 4 0x020c4074 0xffffffff
+DATA 4 0x020c4078 0xffffffff
+DATA 4 0x020c407c 0xffffffff
+DATA 4 0x020c4080 0xffffffff
+DATA 4 0x020c4084 0xffffffff
+
+/* ddr io type */
+DATA 4 0x020e04b4 0x000C0000 /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
+DATA 4 0x020e04ac 0x00000000 /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
+
+/* clock */
+DATA 4 0x020e027c 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK0_P */
+
+/* control and address */
+DATA 4 0x020E0250 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
+DATA 4 0x020E024C 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
+DATA 4 0x020E0490 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
+DATA 4 0x020E0288 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
+DATA 4 0x020E0270 0x00000000 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be
+				configured using Group Control Register:
+				IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+DATA 4 0x020E0260 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT0 */
+DATA 4 0x020E0264 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT1 */
+DATA 4 0x020E04A0 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+
+/* data strobes */
+DATA 4 0x020e0494 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
+DATA 4 0x020e0280 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0_P */
+DATA 4 0x020e0284 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1_P */
+
+/* data */
+DATA 4 0x020E04B0 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
+DATA 4 0x020E0498 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B0DS */
+DATA 4 0x020E04A4 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B1DS */
+DATA 4 0x020E0244 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
+DATA 4 0x020E0248 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
+
+/*
+ * DDR Controller Registers
+ *
+ * Manufacturer:  IM
+ * Device Part Number:  IME1G16D3EEBG-15EI
+ * Clock Freq.:   400MHz
+ * Density per CS in Gb: 1
+ * Chip Selects used: 1
+ * Number of Banks: 8
+ * Row address:     13
+ * Column address:  10
+ * Data bus width 16
+ */
+DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit
+				during MMDC set up */
+
+/*
+ * Calibration setup
+ */
+DATA 4 0x021b0800 0xA1390003 /* DDR_PHY_P0_MPZQHWCTRL, enable both one-time &
+				periodic HW ZQ calibration. */
+
+/*
+ * For target board, may need to run write leveling calibration to fine tune
+ * these settings.
+ */
+DATA 4 0x021b080c 0x00000000
+
+/* Read DQS Gating calibration */
+DATA 4 0x021b083c 0x4164015C /* MPDGCTRL0 PHY0 */
+
+/* Read calibration */
+DATA 4 0x021b0848 0x40404446 /* MPRDDLCTL PHY0 */
+
+/* Write calibration */
+DATA 4 0x021b0850 0x40405A52 /* MPWRDLCTL PHY0 */
+
+/*
+ * read data bit delay: (3 is the reccommended default value, although out of
+ * reset value is 0)
+ */
+DATA 4 0x021b081c 0x33333333 /* DDR_PHY_P0_MPREDQBY0DL3 */
+DATA 4 0x021b0820 0x33333333 /* DDR_PHY_P0_MPREDQBY1DL3 */
+DATA 4 0x021b082c 0xF3333333
+DATA 4 0x021b0830 0xF3333333
+
+DATA 4 0x021b08c0 0x00921012
+
+/* Clock Fine Tuning */
+DATA 4 0x021B0858 0x00000F00 /* [MMDC_MPSDCTRL] MMDC PHY CK Control Register */
+
+/* Complete calibration by forced measurement: */
+DATA 4 0x021b08b8 0x00000800 /* DDR_PHY_P0_MPMUR0, frc_msr */
+/*
+ * Calibration setup end
+ */
+
+/* MMDC init: */
+DATA 4 0x021b0004 0x0002002D /* MMDC0_MDPDC */
+DATA 4 0x021b0008 0x1B333030 /* MMDC0_MDOTC */
+DATA 4 0x021b000c 0x3F4352F3 /* MMDC0_MDCFG0 */
+DATA 4 0x021b0010 0xB66D0B63 /* MMDC0_MDCFG1 */
+DATA 4 0x021b0014 0x01FF00DB /* MMDC0_MDCFG2 */
+
+/*
+ * MDMISC: RALAT kept to the high level of 5.
+ * MDMISC: consider reducing RALAT if your 528MHz board design allow that.
+ * Lower RALAT benefits:
+ * a. better operation at low frequency, for LPDDR2 freq < 100MHz, change RALAT
+ *    to 3
+ * b. Small performence improvment
+ */
+DATA 4 0x021b0018 0x00201740 /* MMDC0_MDMISC */
+
+DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit
+				during MMDC set up */
+
+DATA 4 0x021b002c 0x000026D2 /* MMDC0_MDRWD */
+DATA 4 0x021b0030 0x00431023 /* MMDC0_MDOR */
+DATA 4 0x021b0040 0x00000047 /* Chan0 CS0_END */
+DATA 4 0x021b0000 0x82180000 /* MMDC0_MDCTL */
+
+/* Mode register writes */
+DATA 4 0x021b001c 0x02008032 /* MMDC0_MDSCR, MR2 write, CS0 */
+DATA 4 0x021b001c 0x00008033 /* MMDC0_MDSCR, MR3 write, CS0 */
+DATA 4 0x021b001c 0x00048031 /* MMDC0_MDSCR, MR1 write, CS0 */
+DATA 4 0x021b001c 0x15208030 /* MMDC0_MDSCR, MR0 write, CS0 */
+DATA 4 0x021b001c 0x04008040 /* MMDC0_MDSCR, ZQ calibration command sent to
+				device on CS0 */
+
+DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
+DATA 4 0x021b0818 0x00000227 /* DDR_PHY_P0_MPODTCTRL */
+DATA 4 0x021b0004 0x0002556D /* MMDC0_MDPDC now SDCTL power down enabled */
+DATA 4 0x021b0404 0x00011006 /* MMDC0_MAPSR ADOPT power down enabled, MMDC will
+				enter automatically to self-refresh while the
+				number of idle cycle reached. */
+DATA 4 0x021b001c 0x00000000 /* MMDC0_MDSCR, clear this register (especially
+				the configuration bit as initialization is
+				complete) */

board/ccv/xpress/spl.c new file +116 -0

new file mode 100644
index 0000000..d15b842
@@ -0,0 +1,116 @@
+/*
+ * SPL specific code for CCV xPress
+ *
+ * Copyright (C) 2015-2016 Stefan Roese <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/crm_regs.h>
+
+/* Configuration for IM IME1G16D3EEBG-15EI, 64M x 16 -> 128MiB */
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000030,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_ctlds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+	.grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000030,
+	.dram_odt1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000008,
+	.dram_sdqs0 = 0x00000038,
+	.dram_sdqs1 = 0x00000030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00000000,
+	.p0_mpdgctrl0 = 0x4164015C,
+	.p0_mprddlctl = 0x40404446,
+	.p0_mpwrdlctl = 0x40405A52,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,
+	.cs_density = 20,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.rtt_wr = 2,
+	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
+	.walat = 1,		/* Write additional latency */
+	.ralat = 5,		/* Read additional latency */
+	.mif3_mode = 3,		/* Command prediction working mode */
+	.bi_on = 1,		/* Bank interleaving enabled */
+	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	.ddr_type = DDR_TYPE_DDR3,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 800,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 13,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0xFFFFFFFF, &ccm->CCGR0);
+	writel(0xFFFFFFFF, &ccm->CCGR1);
+	writel(0xFFFFFFFF, &ccm->CCGR2);
+	writel(0xFFFFFFFF, &ccm->CCGR3);
+	writel(0xFFFFFFFF, &ccm->CCGR4);
+	writel(0xFFFFFFFF, &ccm->CCGR5);
+	writel(0xFFFFFFFF, &ccm->CCGR6);
+	writel(0xFFFFFFFF, &ccm->CCGR7);
+}
+
+static void spl_dram_init(void)
+{
+	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* Setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+
+	/* Setup iomux and i2c */
+	board_early_init_f();
+
+	/* Setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+}

board/ccv/xpress/xpress.c new file +331 -0

new file mode 100644
index 0000000..6fc76cd
@@ -0,0 +1,331 @@
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6ul_pins.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-fsl.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
+	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |			\
+	PAD_CTL_ODE)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_SPEED_HIGH   |                                  \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
+
+#define MDIO_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
+
+#define ENET_CLK_PAD_CTRL  (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
+	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
+
+#define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm | PAD_CTL_HYS |			\
+	PAD_CTL_SRE_FAST)
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode =  MX6_PAD_GPIO1_IO02__I2C1_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO02 | PC,
+		.gp = IMX_GPIO_NR(1, 2),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO1_IO03__I2C1_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO03 | PC,
+		.gp = IMX_GPIO_NR(1, 3),
+	},
+};
+
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode =  MX6_PAD_GPIO1_IO00__I2C2_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO00 | PC,
+		.gp = IMX_GPIO_NR(1, 0),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO1_IO01__I2C2_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO01 | PC,
+		.gp = IMX_GPIO_NR(1, 1),
+	},
+};
+
+static struct i2c_pads_info i2c_pad_info4 = {
+	.scl = {
+		.i2c_mode =  MX6_PAD_UART2_TX_DATA__I2C4_SCL | PC,
+		.gpio_mode = MX6_PAD_UART2_TX_DATA__GPIO1_IO20 | PC,
+		.gp = IMX_GPIO_NR(1, 20),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_UART2_RX_DATA__I2C4_SDA | PC,
+		.gpio_mode = MX6_PAD_UART2_RX_DATA__GPIO1_IO21 | PC,
+		.gp = IMX_GPIO_NR(1, 21),
+	},
+};
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_UART4_TX_DATA__UART4_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART4_RX_DATA__UART4_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart5_pads[] = {
+	MX6_PAD_GPIO1_IO04__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO05__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO09__UART5_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO08__UART5_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart8_pads[] = {
+	MX6_PAD_ENET2_TX_DATA1__UART8_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_ENET2_TX_EN__UART8_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_ENET2_TX_CLK__UART8_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_ENET2_RX_ER__UART8_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+	imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+	imx_iomux_v3_setup_multiple_pads(uart8_pads, ARRAY_SIZE(uart8_pads));
+}
+
+/* eMMC on USDHC2 */
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/*
+	 * RST_B
+	 */
+	MX6_PAD_NAND_ALE__USDHC2_RESET_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg = {
+	.esdhc_base = USDHC2_BASE_ADDR,
+	.max_bus_width = 8,
+};
+
+#define USDHC2_PWR_GPIO	IMX_GPIO_NR(1, 9)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	/* eMMC is always present */
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+
+	usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg);
+}
+
+#define USB_OTHERREGS_OFFSET	0x800
+#define UCTRL_PWR_POL		(1 << 9)
+
+static iomux_v3_cfg_t const usb_otg_pads[] = {
+	/* OTG1 */
+	MX6_PAD_SD1_CMD__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD1_DATA0__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
+	/* OTG2 */
+	MX6_PAD_SD1_DATA1__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD1_DATA3__ANATOP_OTG2_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
+};
+
+static void setup_usb(void)
+{
+	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+					 ARRAY_SIZE(usb_otg_pads));
+}
+
+int board_usb_phy_mode(int port)
+{
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return usb_phy_mode(port);
+}
+
+int board_ehci_hcd_init(int port)
+{
+	u32 *usbnc_usb_ctrl;
+
+	if (port > 1)
+		return -EINVAL;
+
+	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
+				 port * 4);
+
+	/* Set Power polarity */
+	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+
+	/* ENET1 reset */
+	MX6_PAD_CSI_MCLK__GPIO4_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* ENET1 interrupt */
+	MX6_PAD_CSI_PIXCLK__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(4, 17)
+
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+	/* Reset LAN8742 PHY */
+	ret = gpio_request(ENET_PHY_RESET_GPIO, "phy-reset");
+	if (!ret)
+		gpio_direction_output(ENET_PHY_RESET_GPIO , 0);
+	mdelay(10);
+	gpio_set_value(ENET_PHY_RESET_GPIO, 1);
+	mdelay(10);
+
+	return cpu_eth_init(bis);
+}
+
+static int setup_fec(int fec_id)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	/*
+	 * Use 50M anatop loopback REF_CLK1 for ENET1,
+	 * clear gpr1[13], set gpr1[17].
+	 */
+	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+			IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+
+	ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
+
+	setup_fec(CONFIG_FEC_ENET_DEV);
+
+	setup_usb();
+
+	return 0;
+}
+
+static const struct boot_mode board_boot_modes[] = {
+	/* 8 bit bus width */
+	{"emmc", MAKE_CFGVAL(0x60, 0x28, 0x00, 0x00)},
+	{ NULL, 0 },
+};
+
+int board_late_init(void)
+{
+	add_board_boot_modes(board_boot_modes);
+	setenv("board_name", "xpress");
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: CCV-EVA xPress\n");
+
+	return 0;
+}

configs/xpress_defconfig new file +6 -0

new file mode 100644
index 0000000..033d32b
@@ -0,0 +1,6 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_XPRESS=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ccv/xpress/imximage.cfg"
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y

configs/xpress_spl_defconfig new file +7 -0

new file mode 100644
index 0000000..c2b1075
@@ -0,0 +1,7 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_XPRESS=y
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg"
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y

include/configs/xpress.h new file +156 -0

new file mode 100644
index 0000000..9bc536b
@@ -0,0 +1,166 @@
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <[email protected]>
+ *
+ * Configuration settings for the CCV xPress board
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __XPRESS_CONFIG_H
+#define __XPRESS_CONFIG_H
+
+#include "mx6_common.h"
+#include <asm/imx-common/gpio.h>
+
+/* SPL options */
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#include "imx6_spl.h"
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 << 20)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
+
+/* I2C configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* Miscellaneous configurable options */
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE			(128 << 20)
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+/* Environment is in stored in the eMMC boot partition */
+#define CONFIG_ENV_SIZE			(16 << 10)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET		(512 << 10)
+#define CONFIG_SYS_MMC_ENV_DEV		0	/* USDHC2 */
+#define CONFIG_SYS_MMC_ENV_PART		1	/* boot parition */
+#define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC2 */
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_CACHE
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
+
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define CONFIG_CMD_MII
+#define CONFIG_FEC_ENET_DEV		0
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR          0x0
+#define CONFIG_FEC_XCV_TYPE             RMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_UBOOT_SECTOR_START	0x2
+#define CONFIG_UBOOT_SECTOR_COUNT	0x3fe
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc0\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"fdt_file=undefined\0" \
+	"fdt_addr=0x83000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+	"uboot=ccv/u-boot.imx\0"					\
+	"uboot_start="__stringify(CONFIG_UBOOT_SECTOR_START)"\0"	\
+	"uboot_size="__stringify(CONFIG_UBOOT_SECTOR_COUNT)"\0"		\
+	"update_uboot=if tftp ${uboot}; then "				\
+		"if itest ${filesize} > 0; then "			\
+			"mmc dev 0 1;"					\
+			"setexpr blkc ${filesize} / 0x200;"		\

Add the base address for the i.MX6UL so that this UART can be used.

Signed-off-by Stefan Roese <[email protected]>

Cc Ye Li <[email protected]>

Cc Fabio Estevam <[email protected]>

Cc Stefano Babic <[email protected]>

---
 arch/arm/include/asm/arch-mx6/imx-regs.h | 1 +
 1 file changed, 1 insertion(+)

arch/arm/include/asm/arch-mx6/imx-regs.h +0 -0

index 5c45bf6..d0e6bf2 100644