sunxi: power: add support for sy8106a driver

SY8106A is a PMIC which is used on the Allwinner H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is implemented to set the default V-CPU voltage to 1200 mV.

This driver is required to retain the SY8106A V-CPU voltage after a software reset. On cold boot the default SY8106A output voltage is selected by a pair of resistors and happens to be 1.2V on the Orange Pi PC and Plus.

Signed-off-by Jelle van der Waa <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

Tested-by Siarhei Siamashka <[email protected]>

Acked-by Siarhei Siamashka <[email protected]>

---
Changes in v2
- Fixed typo in commit message thea => the.
- Made config R_I2C_ENABLE depend on SY8106A_POWER.
- Removed 'default n' from config R_I2C_ENABLE
- Changed SY8106A_POWER description from "most" to "some" boards.
- Added license/copyright to include/sy8106a.h and drivers/power/sy8106a.c.

---
  board/sunxi/Kconfig            |  5 ++++-
  board/sunxi/board.c            |  5 +++++
  configs/orangepi_pc_defconfig  |  2 +-
  drivers/power/Kconfig          | 16 ++++++++++++++++
  drivers/power/Makefile         |  1 +
  drivers/power/sy8106a.c        | 29 +++++++++++++++++++++++++++++
  include/configs/sunxi-common.h |  6 ++++--
  include/sy8106a.h              | 11 +++++++++++
  8 files changed, 71 insertions(+), 4 deletions(-)

create mode 100644 drivers/power/sy8106a.c
create mode 100644 include/sy8106a.h

board/sunxi/Kconfig +4 -1

index a334aa3..5e9d3af 100644
@@ -372,11 +372,14 @@ config I2C3_ENABLE
  	See I2C0_ENABLE help text.
  endif
 
+if SUNXI_GEN_SUN6I
  config R_I2C_ENABLE
  	bool "Enable the PRCM I2C/TWI controller"
-	default n
+	# This is used for the pmic on H3
+	default y if SY8106A_POWER
  	---help---
  	Set this to y to enable the I2C controller which is part of the PRCM.
+endif
 
  if MACH_SUN7I
  config I2C4_ENABLE

board/sunxi/board.c +5 -0

index 420481a..15b7af6 100644
@@ -25,6 +25,7 @@
  #include <asm/io.h>
  #include <nand.h>
  #include <net.h>
+#include <sy8106a.h>
 
  #if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
  /* So that we can use pin names in Kconfig and sunxi_name_to_gpio() */

@@ -436,6 +437,10 @@ void sunxi_board_init(void)
  	int power_failed = 0;
  	unsigned long ramsize;
 
+#ifdef CONFIG_SY8106A_POWER
+	power_failed = sy8106a_set_vout1(CONFIG_SY8106A_VOUT1_VOLT);
+#endif
+
  #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
  	defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
  	power_failed = axp_init();

configs/orangepi_pc_defconfig +1 -1

index ea9ed87..29a8da6 100644
@@ -12,4 +12,4 @@ CONFIG_SPL=y
  # CONFIG_CMD_FLASH is not set
  # CONFIG_CMD_FPGA is not set
  CONFIG_CMD_GPIO=y
-CONFIG_R_I2C_ENABLE=y
+CONFIG_SY8106A_POWER=y

drivers/power/Kconfig +16 -0

index 10683a2..adc6455 100644
@@ -48,6 +48,13 @@ config AXP818_POWER
  	Say y here to enable support for the axp818 pmic found on
  	A83T dev board.
 
+config SY8106A_POWER
+	boolean "SY8106A pmic support"
+	depends on MACH_SUN8I_H3
+	---help---
+	Select this to enable support for the SY8106A pmic found on some
+	H3 boards.
+
  endchoice
 
  config AXP_DCDC1_VOLT

@@ -232,4 +239,13 @@ config AXP_ELDO3_VOLT
  	1.2V for the SSD2828 chip (converter of parallel LCD interface
  	into MIPI DSI).
 
+config SY8106A_VOUT1_VOLT
+	int "SY8106A pmic VOUT1 voltage"
+	depends on SY8106A_POWER
+	default 1200
+	---help---
+	Set the voltage (mV) to program the SY8106A pmic VOUT1. This
+	is typically used to power the VDD-CPU and should be 1200mV.
+	Values can range from 680mV till 1950mV.
+
  endmenu

drivers/power/Makefile +1 -0

index 0fdbca3..690faa0 100644
@@ -12,6 +12,7 @@ obj-$(CONFIG_AXP221_POWER)	+= axp221.o
  obj-$(CONFIG_AXP818_POWER)	+= axp818.o
  obj-$(CONFIG_EXYNOS_TMU)	+= exynos-tmu.o
  obj-$(CONFIG_FTPMU010_POWER)	+= ftpmu010.o
+obj-$(CONFIG_SY8106A_POWER)	+= sy8106a.o
  obj-$(CONFIG_TPS6586X_POWER)	+= tps6586x.o
  obj-$(CONFIG_TWL4030_POWER)	+= twl4030.o
  obj-$(CONFIG_TWL6030_POWER)	+= twl6030.o

drivers/power/sy8106a.c new file +29 -0

new file mode 100644
index 0000000..bbf116f
@@ -0,0 +1,29 @@
+/*
+ * (C) Copyright 2016
+ * Jelle van der Waa <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <i2c.h>
+#include <sy8106a.h>
+
+#define SY8106A_I2C_ADDR 0x65
+#define SY8106A_VOUT1_SEL 1
+#define SY8106A_VOUT1_SEL_ENABLE (1 << 7)
+
+static u8 sy8106a_mvolt_to_cfg(int mvolt, int min, int max, int div)
+{
+	if (mvolt < min)
+		mvolt = min;
+	else if (mvolt > max)
+		mvolt = max;
+
+	return (mvolt - min) / div;
+}
+
+int sy8106a_set_vout1(unsigned int mvolt)
+{
+	u8 data = sy8106a_mvolt_to_cfg(mvolt, 680, 1950, 10) | SY8106A_VOUT1_SEL_ENABLE;
+	return i2c_write(SY8106A_I2C_ADDR, SY8106A_VOUT1_SEL, 1, &data, 1);
+}

include/configs/sunxi-common.h +4 -2

index b4dfb3c..40850e5 100644
@@ -206,7 +206,8 @@
  #define CONFIG_SPL_STACK		LOW_LEVEL_SRAM_STACK
 
  /* I2C */
-#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER
+#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
+    defined CONFIG_SY8106A_POWER
  #define CONFIG_SPL_I2C_SUPPORT
  #endif
 

@@ -240,7 +241,8 @@ extern int soft_i2c_gpio_scl;
 
  /* PMU */
  #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
-    defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
+    defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER || \
+    defined CONFIG_SY8106A_POWER
  #define CONFIG_SPL_POWER_SUPPORT
  #endif
 

include/sy8106a.h new file +11 -0

new file mode 100644
index 0000000..32e8c43
@@ -0,0 +1,11 @@
+/*
+ * (C) Copyright 2016
+ * Jelle van der Waa <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef _SY8106A_PMIC_H_
+
+int sy8106a_set_vout1(unsigned int mvolt);
+
+#endif