Skip to contentSkip to conversation

sunxi: Support SID e-fuses on A83T and H3

PATCH Applied Chen-Yu Tsai 3 participants 6 messages Jan 27, 2016 – Mar 20, 2016

Subsystems (2)
Arm (32-bit) Arm/Allwinner sunXi SoC support
lore
Share & tools
lore

Chen-Yu Tsai

author
#0 lore raw

PATCH 1/1 sunxi: Support SID e-fuses on A83T and H3

On the A83T and H3, the SID block is at a different address. Furthurmore, the e-fuses are at an offset of 0x200 within the hardware's address space.

Signed-off-by Chen-Yu Tsai <[email protected]>
---
 arch/arm/include/asm/arch-sunxi/cpu_sun4i.h | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm/include/asm/arch-sunxi/cpu_sun4i.h +7 -0
index 0cdefdc..f797649 100644
@@ -74,7 +74,14 @@
 #define SUNXI_AD_DA_BASE		0x01c22c00
 #define SUNXI_KEYPAD_BASE		0x01c23000
 #define SUNXI_TZPC_BASE			0x01c23400
+
+#if defined(CONFIG_MACH_SUN8I_A83T) || defined(CONFIG_MACH_SUN8I_H3)
+/* SID address space starts at 0x01c1400, but e-fuse is at offset 0x200 */
+#define SUNXI_SID_BASE			0x01c14200
+#else
 #define SUNXI_SID_BASE			0x01c23800
+#endif
+
 #define SUNXI_SJTAG_BASE		0x01c23c00
 
 #define SUNXI_TP_BASE			0x01c25000
Signature · 1 line
2.7.0
author
#1 lore raw

PATCH 1/1 sunxi: Add support for Cubietruck Plus

Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.

DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 is connected to the reset control of the PHY. EMAC is not actually supported yet.

The DTS is the same as the one already in the kernel.

Signed-off-by Chen-Yu Tsai <[email protected]>
---
 arch/arm/dts/Makefile                       |  1 +
 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 65 +++++++++++++++++++++++++++++
 configs/Cubietruck_plus_defconfig           | 18 ++++++++
 3 files changed, 84 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
 create mode 100644 configs/Cubietruck_plus_defconfig
arch/arm/dts/Makefile +1 -0
index 1c7d359..e338db5 100644
@@ -184,6 +184,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \
 	sun8i-a33-sinlinx-sina33.dtb
 dtb-$(CONFIG_MACH_SUN8I_A83T) += \
 	sun8i-a83t-allwinner-h8homlet-v2.dtb \
+	sun8i-a83t-cubietruck-plus.dtb \
 	sun8i-a83t-sinovoip-bpi-m3.dtb
 dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h3-orangepi-pc.dtb \
arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file +65 -0

65 lines not on this page · raw message

configs/Cubietruck_plus_defconfig new file +18 -0
new file mode 100644
index 0000000..bb0b336
@@ -0,0 +1,18 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A83T=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=15355
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_I2C0_ENABLE=y
+CONFIG_AXP_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO3_VOLT=2500
+CONFIG_AXP_DLDO4_VOLT=3300
Signature · 1 line
2.7.0
#2 lore raw

PATCH 1/1 sunxi: Add support for Cubietruck Plus

Hans,

What is the status of this patch?

Dennis

Quoted 130 lines · CDT Chen-Yu Tsai

Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.

DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 is connected to the reset control of the PHY. EMAC is not actually supported yet.

The DTS is the same as the one already in the kernel.

Signed-off-by Chen-Yu Tsai <[email protected]>
---
 arch/arm/dts/Makefile                       |  1 +
 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 65
+++++++++++++++++++++++++++++ configs/Cubietruck_plus_defconfig           |
18 ++++++++
 3 files changed, 84 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
 create mode 100644 configs/Cubietruck_plus_defconfig
arch/arm/dts/Makefile +1 -0
index 1c7d359..e338db5 100644
@@ -184,6 +184,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \
 	sun8i-a33-sinlinx-sina33.dtb
 dtb-$(CONFIG_MACH_SUN8I_A83T) += \
 	sun8i-a83t-allwinner-h8homlet-v2.dtb \
+	sun8i-a83t-cubietruck-plus.dtb \
 	sun8i-a83t-sinovoip-bpi-m3.dtb
 dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h3-orangepi-pc.dtb \
(quoted diff) +0 -0

b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file mode 100644 index 0000000..88b1e09

arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file +65 -0
@@ -0,0 +1,65 @@
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a83t.dtsi"
+
+/ {
+	model = "Cubietech Cubietruck Plus";
+	compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_b>;
+	status = "okay";
+};
(quoted diff) +0 -0

b/configs/Cubietruck_plus_defconfig new file mode 100644 index 0000000..bb0b336

configs/Cubietruck_plus_defconfig new file +18 -0
@@ -0,0 +1,18 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A83T=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=15355
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_I2C0_ENABLE=y
+CONFIG_AXP_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO3_VOLT=2500
+CONFIG_AXP_DLDO4_VOLT=3300
#3 lore raw

PATCH 1/1 sunxi: Add support for Cubietruck Plus

Quoted 5 lines · CDT Dennis Gilmore

Hans,

What is the status of this patch?

Dennis

With the patch applied building for Cubietruck_plus fails with

ld.bfd -pie --gc-sections -Bstatic -Ttext 0x4a000000 -o u-boot -T u-
boot.lds arch/arm/cpu/armv7/start.o --start-group arch/arm/cpu/built-in.o arch/arm/cpu/armv7/built-in.o arch/arm/lib/built-in.o board/sunxi/built-in.o cmd/built-in.o common/built-in.o disk/built-in.o drivers/built-in.o drivers/dma/built-in.o drivers/gpio/built-in.o drivers/i2c/built-in.o drivers/mmc/built-in.o drivers/mtd/built-in.o drivers/mtd/onenand/built-in.o drivers/mtd/spi/built-in.o drivers/net/built-in.o drivers/net/phy/built-in.o drivers/pci/built-in.o drivers/power/built-in.o drivers/power/battery/built- in.o drivers/power/fuel_gauge/built-in.o drivers/power/mfd/built-in.o drivers/power/pmic/built-in.o drivers/power/regulator/built-in.o drivers/ serial/built-in.o drivers/spi/built-in.o drivers/usb/dwc3/built-in.o drivers/usb/emul/built-in.o drivers/usb/eth/built-in.o drivers/usb/gadget/ built-in.o drivers/usb/gadget/udc/built-in.o drivers/usb/host/built-in.o drivers/usb/musb-new/built-in.o drivers/usb/musb/built-in.o drivers/usb/phy/ built-in.o drivers/usb/ulpi/built-in.o fs/built-in.o lib/built-in.o net/ built-in.o test/built-in.o test/dm/built-in.o --end-group arch/arm/lib/ eabi_compat.o -L /usr/lib/gcc/armv7hl-redhat-linux-gnueabi/6.0.0 -lgcc -Map u-boot.map
board/sunxi/built-in.o: In function `i2c_init_board':
/builddir/build/BUILD/u-boot-2016.03/board/sunxi/board.c:363: undefined reference to `clock_twi_onoff'
ld.bfd: BFD version 2.26.20160125 assertion fail elf32-arm.c:8434 ld.bfd: error: required section '.rel.plt' not found in the linker script ld.bfd: final link failed: Invalid operation

Quoted 140 lines · CDT Chen-Yu Tsai
Quoted 139 lines

Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.

DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 is connected to the reset control of the PHY. EMAC is not actually supported yet.

The DTS is the same as the one already in the kernel.

Signed-off-by Chen-Yu Tsai <[email protected]>

---

 arch/arm/dts/Makefile                       |  1 +
 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 65

+++++++++++++++++++++++++++++ configs/Cubietruck_plus_defconfig |
18 ++++++++

 3 files changed, 84 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
 create mode 100644 configs/Cubietruck_plus_defconfig
arch/arm/dts/Makefile +1 -0
index 1c7d359..e338db5 100644
@@ -184,6 +184,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \
 
 	sun8i-a33-sinlinx-sina33.dtb
 
 dtb-$(CONFIG_MACH_SUN8I_A83T) += \
 
 	sun8i-a83t-allwinner-h8homlet-v2.dtb \
 
+	sun8i-a83t-cubietruck-plus.dtb \
 
 	sun8i-a83t-sinovoip-bpi-m3.dtb
 
 dtb-$(CONFIG_MACH_SUN8I_H3) += \
 
 	sun8i-h3-orangepi-pc.dtb \
(quoted diff) +0 -0

b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file mode 100644 index 0000000..88b1e09

arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file +65 -0
@@ -0,0 +1,65 @@
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a83t.dtsi"
+
+/ {
+	model = "Cubietech Cubietruck Plus";
+	compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_b>;
+	status = "okay";
+};
(quoted diff) +0 -0

b/configs/Cubietruck_plus_defconfig new file mode 100644 index 0000000..bb0b336

configs/Cubietruck_plus_defconfig new file +15 -0
@@ -0,0 +1,18 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A83T=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=15355
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_I2C0_ENABLE=y
+CONFIG_AXP_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
Quoted 8 lines

configs/Cubietruck_plus_defconfig line 18

Quoted 3 lines
configs/Cubietruck_plus_defconfig new file +3 -0
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO3_VOLT=2500
+CONFIG_AXP_DLDO4_VOLT=3300

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: This is a digitally signed message part.
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20160319/c818a94d/attachment.sig>

#4 lore raw

[U-Boot] [linux-sunxi] Re: [PATCH] sunxi: Add support for Cubietruck Plus

In reply to Dennis Gilmore

hI,

Quoted 3 lines · Dennis Gilmore

Hans,

What is the status of this patch?

I added this to my sunxi-wip tree (including a fix for the build error) a couple of days ago. I will send a pull-req for various u-boot sunxi patch soonish and then it will hit mainline.

Regards,

Hans

Quoted 136 lines

Dennis

Quoted 130 lines · CDT Chen-Yu Tsai

Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.

DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 is connected to the reset control of the PHY. EMAC is not actually supported yet.

The DTS is the same as the one already in the kernel.

Signed-off-by Chen-Yu Tsai <[email protected]>
---
  arch/arm/dts/Makefile                       |  1 +
  arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 65
+++++++++++++++++++++++++++++ configs/Cubietruck_plus_defconfig           |
18 ++++++++
  3 files changed, 84 insertions(+)

create mode 100644 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts create mode 100644 configs/Cubietruck_plus_defconfig

arch/arm/dts/Makefile +1 -0
index 1c7d359..e338db5 100644
@@ -184,6 +184,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \
  	sun8i-a33-sinlinx-sina33.dtb
  dtb-$(CONFIG_MACH_SUN8I_A83T) += \
  	sun8i-a83t-allwinner-h8homlet-v2.dtb \
+	sun8i-a83t-cubietruck-plus.dtb \
  	sun8i-a83t-sinovoip-bpi-m3.dtb
  dtb-$(CONFIG_MACH_SUN8I_H3) += \
  	sun8i-h3-orangepi-pc.dtb \
(quoted diff) +0 -0

b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file mode 100644 index 0000000..88b1e09

arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file +65 -0
@@ -0,0 +1,65 @@
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a83t.dtsi"
+
+/ {
+	model = "Cubietech Cubietruck Plus";
+	compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_b>;
+	status = "okay";
+};
(quoted diff) +0 -0

b/configs/Cubietruck_plus_defconfig new file mode 100644 index 0000000..bb0b336

configs/Cubietruck_plus_defconfig new file +18 -0
@@ -0,0 +1,18 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A83T=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=15355
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_I2C0_ENABLE=y
+CONFIG_AXP_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO3_VOLT=2500
+CONFIG_AXP_DLDO4_VOLT=3300
Applied
#5 lore raw
In reply to Chen-Yu Tsai

Hi,

Quoted 5 lines · Chen-Yu Tsai

On the A83T and H3, the SID block is at a different address. Furthurmore, the e-fuses are at an offset of 0x200 within the hardware's address space.

Signed-off-by Chen-Yu Tsai <[email protected]>

Thanks, applied to my tree and this will go out with the next pull-req.

Regards,

Hans

Quoted 24 lines
---
  arch/arm/include/asm/arch-sunxi/cpu_sun4i.h | 7 +++++++
  1 file changed, 7 insertions(+)
arch/arm/include/asm/arch-sunxi/cpu_sun4i.h +7 -0
index 0cdefdc..f797649 100644
@@ -74,7 +74,14 @@
  #define SUNXI_AD_DA_BASE		0x01c22c00
  #define SUNXI_KEYPAD_BASE		0x01c23000
  #define SUNXI_TZPC_BASE			0x01c23400
+
+#if defined(CONFIG_MACH_SUN8I_A83T) || defined(CONFIG_MACH_SUN8I_H3)
+/* SID address space starts at 0x01c1400, but e-fuse is at offset 0x200 */
+#define SUNXI_SID_BASE			0x01c14200
+#else
  #define SUNXI_SID_BASE			0x01c23800
+#endif
+
  #define SUNXI_SJTAG_BASE		0x01c23c00
 
  #define SUNXI_TP_BASE			0x01c25000