sunxi: Add defconfig for Sinlinx SinA31s
PATCH 1/1 sunxi: Add defconfig for Sinlinx SinA31s
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components. There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0 hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume buttons, RS232 style UART and USB OTG (though VBUS is not connected). Various headers are available for other addon modules, such as SDIO WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
--- board/sunxi/MAINTAINERS | 6 ++++++ configs/Sinlinx_SinA31s_defconfig | 21 +++++++++++++++++++++ 2 files changed, 27 insertions(+) create mode 100644 configs/Sinlinx_SinA31s_defconfig
board/sunxi/MAINTAINERS +6 -0
@@ -191,6 +191,12 @@ M: Siarhei Siamashka <[email protected]> S: Maintained F: configs/MSI_Primo81_defconfig +SINLINX SINA31s BOARD +M: Chen-Yu Tsai <[email protected]> +S: Maintained +F: configs/Sinlinx_SinA31s_defconfig +W: http://linux-sunxi.org/Sinlinx_SinA31s + SINLINX SINA33 BOARD M: Chen-Yu Tsai <[email protected]> S: Maintained
configs/Sinlinx_SinA31s_defconfig new file +21 -0
@@ -0,0 +1,21 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_MACH_SUN6I=y +CONFIG_DRAM_CLK=432 +CONFIG_DRAM_ZQ=251 +CONFIG_MMC0_CD_PIN="PA4" +CONFIG_MMC3_PINS="PC" +CONFIG_MMC_SUNXI_SLOT_EXTRA=3 +CONFIG_USB1_VBUS_PIN="" +CONFIG_USB2_VBUS_PIN="" +CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-sina31s" +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_FPGA is not set +CONFIG_ETH_DESIGNWARE=y +CONFIG_AXP_DLDO1_VOLT=3300 +CONFIG_USB_EHCI_HCD=y
Signature · 1 line
2.7.0
Hans de Goede
AppliedPATCH 1/1 sunxi: Add defconfig for Sinlinx SinA31s
Hi,
Quoted 5 lines · Chen-Yu Tsai
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components. There are also pads for UART0, JTAG and I2S.
Quoted 7 lines
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0 hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume buttons, RS232 style UART and USB OTG (though VBUS is not connected). Various headers are available for other addon modules, such as SDIO WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by Chen-Yu Tsai <[email protected]>
Thanks, applied.
Regards,
Hans
Quoted 51 lines
--- board/sunxi/MAINTAINERS | 6 ++++++ configs/Sinlinx_SinA31s_defconfig | 21 +++++++++++++++++++++ 2 files changed, 27 insertions(+)create mode 100644 configs/Sinlinx_SinA31s_defconfig
board/sunxi/MAINTAINERS +6
-0@@ -191,6 +191,12 @@ M: Siarhei Siamashka <[email protected]> S: Maintained F: configs/MSI_Primo81_defconfig +SINLINX SINA31s BOARD +M: Chen-Yu Tsai <[email protected]> +S: Maintained +F: configs/Sinlinx_SinA31s_defconfig +W: http://linux-sunxi.org/Sinlinx_SinA31s + SINLINX SINA33 BOARD M: Chen-Yu Tsai <[email protected]> S: Maintainedconfigs/Sinlinx_SinA31s_defconfig new file +21
-0@@ -0,0 +1,21 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_MACH_SUN6I=y +CONFIG_DRAM_CLK=432 +CONFIG_DRAM_ZQ=251 +CONFIG_MMC0_CD_PIN="PA4" +CONFIG_MMC3_PINS="PC" +CONFIG_MMC_SUNXI_SLOT_EXTRA=3 +CONFIG_USB1_VBUS_PIN="" +CONFIG_USB2_VBUS_PIN="" +CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-sina31s" +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_FPGA is not set +CONFIG_ETH_DESIGNWARE=y +CONFIG_AXP_DLDO1_VOLT=3300 +CONFIG_USB_EHCI_HCD=y