drivers: net: cpsw: Add readinf of DT phy-handle node

Add the ability to pass the phy-handle node offset to the phy driver. This allows the phy driver to access the DT subnode's data and parse accordingly.

Signed-off-by Dan Murphy <[email protected]>

Add the ability to pass the phy-handle node offset to the phy driver. This allows the phy driver to access the DT subnode's data and parse accordingly.

Signed-off-by Dan Murphy <[email protected]>

---
 drivers/net/zynq_gem.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)

drivers/net/zynq_gem.c +5 -0

index aec8077..722927a 100644
@@ -179,6 +179,7 @@ struct zynq_gem_priv {
 	struct zynq_gem_regs *iobase;
 	phy_interface_t interface;
 	struct phy_device *phydev;
+	int phy_of_handle;
 	struct mii_dev *bus;
 };
 

@@ -352,6 +353,10 @@ static int zynq_phy_init(struct udevice *dev)
 	priv->phydev->supported = supported | ADVERTISED_Pause |
 				  ADVERTISED_Asym_Pause;
 	priv->phydev->advertising = priv->phydev->supported;
+
+	if (priv->phy_of_handle > 0)
+		priv->phydev->dev->of_offset = priv->phy_of_handle;
+
 	phy_config(priv->phydev);
 
 	return 0;

Add the device tree bindings and the accompanying documentation for the TI DP83867 Giga bit ethernet phy driver.

The original document was from:

    [commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel]

Signed-off-by Dan Murphy <[email protected]>

Add the device tree bindings and the accompanying documentation for the TI DP83867 Giga bit ethernet phy driver.

The original document was from:

    [commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel]

Signed-off-by Dan Murphy <[email protected]>

---

v3- Update the bindings to the reflect the implementation

 doc/device-tree-bindings/net/ti,dp83867.txt | 25 +++++++++++++++++++++
 include/dt-bindings/net/ti-dp83867.h        | 35 +++++++++++++++++++++++++++++
 2 files changed, 60 insertions(+)
 create mode 100644 doc/device-tree-bindings/net/ti,dp83867.txt
 create mode 100644 include/dt-bindings/net/ti-dp83867.h

doc/device-tree-bindings/net/ti,dp83867.txt new file +25 -0

new file mode 100644
index 0000000..cb77fdf
@@ -0,0 +1,25 @@
+* Texas Instruments - dp83867 Giga bit ethernet phy
+
+Required properties:
+	- reg - The ID number for the phy, usually a small integer
+	- ti,rx-internal-delay - RGMII Recieve Clock Delay - see dt-bindings/net/ti-dp83867.h
+		for applicable values
+	- ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h
+		for applicable values
+	- ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h
+		for applicable values
+
+Default child nodes are standard Ethernet PHY device
+nodes as described in doc/devicetree/bindings/net/ethernet.txt
+
+Example:
+
+	ethernet-phy at 0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+	};
+
+Datasheet can be found:
+http://www.ti.com/product/DP83867IR/datasheet

include/dt-bindings/net/ti-dp83867.h new file +0 -0

new file mode 100644
index 0000000..5c592fb

include/dt-bindings/net/ti-dp83867.h new file +20 -0

+ */
+
+#ifndef _DT_BINDINGS_TI_DP83867_H
+#define _DT_BINDINGS_TI_DP83867_H
+
+/* PHY CTRL bits */
+#define DP83867_PHYCR_FIFO_DEPTH_3_B_NIB	0x00
+#define DP83867_PHYCR_FIFO_DEPTH_4_B_NIB	0x01
+#define DP83867_PHYCR_FIFO_DEPTH_6_B_NIB	0x02
+#define DP83867_PHYCR_FIFO_DEPTH_8_B_NIB	0x03
+
+/* RGMIIDCTL internal delay for rx and tx */
+#define	DP83867_RGMIIDCTL_250_PS	0x0
+#define	DP83867_RGMIIDCTL_500_PS	0x1
+#define	DP83867_RGMIIDCTL_750_PS	0x2
+#define	DP83867_RGMIIDCTL_1_NS		0x3
+#define	DP83867_RGMIIDCTL_1_25_NS	0x4
+#define	DP83867_RGMIIDCTL_1_50_NS	0x5
+#define	DP83867_RGMIIDCTL_1_75_NS	0x6
+#define	DP83867_RGMIIDCTL_2_00_NS	0x7

Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default.

If devicetree is not used then use the default defines within the driver.

Signed-off-by Dan Murphy <[email protected]>

Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default.

If devicetree is not used then use the default defines within the driver.

Signed-off-by Dan Murphy <[email protected]>

---

v4 - Rebased the driver and changed default values to -1

 drivers/net/phy/ti.c | 85 +++++++++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 75 insertions(+), 10 deletions(-)

drivers/net/phy/ti.c +29 -4

index 937426b..922f0a4 100644
@@ -6,6 +6,14 @@
  */
 #include <common.h>
 #include <phy.h>
+#include <linux/compat.h>
+#include <malloc.h>
+
+#include <fdtdec.h>
+#include <dm.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+DECLARE_GLOBAL_DATA_PTR;
 
 /* TI DP83867 */
 #define DP83867_DEVADDR		0x1f

@@ -71,6 +79,17 @@
 #define MII_MMD_CTRL_INCR_RDWT	0x8000 /* post increment on reads & writes */
 #define MII_MMD_CTRL_INCR_ON_WT	0xC000 /* post increment on writes only */
 
+/* User setting - can be taken from DTS */
+#define DEFAULT_RX_ID_DELAY	DP83867_RGMIIDCTL_2_25_NS
+#define DEFAULT_TX_ID_DELAY	DP83867_RGMIIDCTL_2_75_NS
+#define DEFAULT_FIFO_DEPTH	DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
+
+struct dp83867_private {
+	int rx_id_delay;
+	int tx_id_delay;
+	int fifo_depth;
+};
+
 /**
  * phy_read_mmd_indirect - reads data from the MMD registers
  * @phydev: The PHY device bus

@@ -148,16 +167,58 @@ static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
 		phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
 }
 
-/* User setting - can be taken from DTS */
-#define RX_ID_DELAY	8
-#define TX_ID_DELAY	0xa
-#define FIFO_DEPTH	1
+#if defined(CONFIG_DM_ETH)
+/**
+ * dp83867_data_init - Convenience function for setting PHY specific data
+ *
+ * @phydev: the phy_device struct
+ */
+static int dp83867_of_init(struct phy_device *phydev)
+{
+	struct dp83867_private *dp83867 = phydev->priv;
+	struct udevice *dev = phydev->dev;

drivers/net/phy/ti.c +28 -2

+	return 0;
+}
+#else
+static int dp83867_of_init(struct phy_device *phydev)
+{
+	dp83867->rx_id_delay = DEFAULT_RX_ID_DELAY;
+	dp83867->tx_id_delay = DEFAULT_TX_ID_DELAY;
+	dp83867->fifo_depth = DEFAULT_FIFO_DEPTH;
+
+	return 0;
+}
+#endif
 
 static int dp83867_config(struct phy_device *phydev)
 {
+	struct dp83867_private *dp83867;
 	unsigned int val, delay, cfg2;
 	int ret;
 
+	if (!phydev->priv) {
+		dp83867 = kzalloc(sizeof(*dp83867), GFP_KERNEL);
+		if (!dp83867)
+			return -ENOMEM;
+
+		phydev->priv = dp83867;
+		ret = dp83867_of_init(phydev);
+		if (ret)
+			goto err_out;
+	} else {
+		dp83867 = (struct dp83867_private *)phydev->priv;
+	}
+
 	/* Restart the PHY.  */
 	val = phy_read(phydev, MDIO_DEVAD_NONE, DP83867_CTRL);
 	phy_write(phydev, MDIO_DEVAD_NONE, DP83867_CTRL,

@@ -166,9 +227,9 @@ static int dp83867_config(struct phy_device *phydev)
 	if (phy_interface_is_rgmii(phydev)) {
 		ret = phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_PHYCTRL,
 			(DP83867_MDI_CROSSOVER_AUTO << DP83867_MDI_CROSSOVER) |
-			(FIFO_DEPTH << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
+			(dp83867->fifo_depth << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
 		if (ret)
-			return ret;
+			goto err_out;
 	} else {
 		phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR,
 			  (BMCR_ANENABLE | BMCR_FULLDPLX | BMCR_SPEED1000));

drivers/net/phy/ti.c +2 -2

 		phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_BISCR, 0x0);
 	}
 

@@ -212,8 +273,8 @@ static int dp83867_config(struct phy_device *phydev)
 		phy_write_mmd_indirect(phydev, DP83867_RGMIICTL,
 				       DP83867_DEVADDR, phydev->addr, val);
 
-		delay = (RX_ID_DELAY |
-			 (TX_ID_DELAY << DP83867_RGMII_TX_CLK_DELAY_SHIFT));
+		delay = (dp83867->rx_id_delay |
+			 (dp83867->tx_id_delay << DP83867_RGMII_TX_CLK_DELAY_SHIFT));
 
 		phy_write_mmd_indirect(phydev, DP83867_RGMIIDCTL,
 				       DP83867_DEVADDR, phydev->addr, delay);

Quoted 75 lines · Dan Murphy

Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default.

If devicetree is not used then use the default defines within the driver.

Signed-off-by Dan Murphy <[email protected]>

---

v4 - Rebased the driver and changed default values to -1

 drivers/net/phy/ti.c | 85 +++++++++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 75 insertions(+), 10 deletions(-)

drivers/net/phy/ti.c +33 -4

index 937426b..922f0a4 100644
@@ -6,6 +6,14 @@
  */
 #include <common.h>
 #include <phy.h>
+#include <linux/compat.h>
+#include <malloc.h>
+
+#include <fdtdec.h>
+#include <dm.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+DECLARE_GLOBAL_DATA_PTR;
 
 /* TI DP83867 */
 #define DP83867_DEVADDR		0x1f

@@ -71,6 +79,17 @@
 #define MII_MMD_CTRL_INCR_RDWT	0x8000 /* post increment on reads & writes */
 #define MII_MMD_CTRL_INCR_ON_WT	0xC000 /* post increment on writes only */
 
+/* User setting - can be taken from DTS */
+#define DEFAULT_RX_ID_DELAY	DP83867_RGMIIDCTL_2_25_NS
+#define DEFAULT_TX_ID_DELAY	DP83867_RGMIIDCTL_2_75_NS
+#define DEFAULT_FIFO_DEPTH	DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
+
+struct dp83867_private {
+	int rx_id_delay;
+	int tx_id_delay;
+	int fifo_depth;
+};
+
 /**
  * phy_read_mmd_indirect - reads data from the MMD registers
  * @phydev: The PHY device bus

@@ -148,16 +167,58 @@ static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
 		phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
 }
 
-/* User setting - can be taken from DTS */
-#define RX_ID_DELAY	8
-#define TX_ID_DELAY	0xa
-#define FIFO_DEPTH	1
+#if defined(CONFIG_DM_ETH)
+/**
+ * dp83867_data_init - Convenience function for setting PHY specific data
+ *
+ * @phydev: the phy_device struct
+ */
+static int dp83867_of_init(struct phy_device *phydev)
+{
+	struct dp83867_private *dp83867 = phydev->priv;
+	struct udevice *dev = phydev->dev;
+
+	dp83867->rx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,rx_internal_delay", -1);
+

drivers/net/phy/ti.c static inline bool phy_interface_is_rgmii(struct phy_device *phydev) · line 189

Quoted 6 lines

drivers/net/phy/ti.c +6 -0

+	dp83867->tx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,tx_internal_delay", -1);
+
+	dp83867->fifo_depth = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,fifo_depth", -1);
+

These names are still incompatible with binding you have. There are dashes instead of underscores.

Quoted 50 lines

drivers/net/phy/ti.c +28 -2

+	return 0;
+}
+#else
+static int dp83867_of_init(struct phy_device *phydev)
+{
+	dp83867->rx_id_delay = DEFAULT_RX_ID_DELAY;
+	dp83867->tx_id_delay = DEFAULT_TX_ID_DELAY;
+	dp83867->fifo_depth = DEFAULT_FIFO_DEPTH;
+
+	return 0;
+}
+#endif
 
 static int dp83867_config(struct phy_device *phydev)
 {
+	struct dp83867_private *dp83867;
 	unsigned int val, delay, cfg2;
 	int ret;
 
+	if (!phydev->priv) {
+		dp83867 = kzalloc(sizeof(*dp83867), GFP_KERNEL);
+		if (!dp83867)
+			return -ENOMEM;
+
+		phydev->priv = dp83867;
+		ret = dp83867_of_init(phydev);
+		if (ret)
+			goto err_out;
+	} else {
+		dp83867 = (struct dp83867_private *)phydev->priv;
+	}
+
 	/* Restart the PHY.  */
 	val = phy_read(phydev, MDIO_DEVAD_NONE, DP83867_CTRL);
 	phy_write(phydev, MDIO_DEVAD_NONE, DP83867_CTRL,

@@ -166,9 +227,9 @@ static int dp83867_config(struct phy_device *phydev)
 	if (phy_interface_is_rgmii(phydev)) {
 		ret = phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_PHYCTRL,
 			(DP83867_MDI_CROSSOVER_AUTO << DP83867_MDI_CROSSOVER) |
-			(FIFO_DEPTH << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
+			(dp83867->fifo_depth << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
 		if (ret)
-			return ret;
+			goto err_out;
 	} else {
 		phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR,
 			  (BMCR_ANENABLE | BMCR_FULLDPLX | BMCR_SPEED1000));

drivers/net/phy/ti.c static int dp83867_config(struct phy_device *phydev) · line 254

Quoted 7 lines

drivers/net/phy/ti.c +2 -2

@@ -189,8 +250,8 @@ static int dp83867_config(struct phy_device *phydev)
 			  DP83867_PHYCTRL_SGMIIEN |
 			  (DP83867_MDI_CROSSOVER_MDIX <<
 			  DP83867_MDI_CROSSOVER) |
-			  (FIFO_DEPTH << DP83867_PHYCTRL_RXFIFO_SHIFT) |
-			  (FIFO_DEPTH  << DP83867_PHYCTRL_TXFIFO_SHIFT));
+			  (dp83867->fifo_depth << DP83867_PHYCTRL_RXFIFO_SHIFT) |
+			  (dp83867->fifo_depth  << DP83867_PHYCTRL_TXFIFO_SHIFT));

                                              ^^

Here are 2 spaces instead of 1

Quoted 25 lines

drivers/net/phy/ti.c +6 -2

 		phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_BISCR, 0x0);
 	}
 

@@ -212,8 +273,8 @@ static int dp83867_config(struct phy_device *phydev)
 		phy_write_mmd_indirect(phydev, DP83867_RGMIICTL,
 				       DP83867_DEVADDR, phydev->addr, val);
 
-		delay = (RX_ID_DELAY |
-			 (TX_ID_DELAY << DP83867_RGMII_TX_CLK_DELAY_SHIFT));
+		delay = (dp83867->rx_id_delay |
+			 (dp83867->tx_id_delay << DP83867_RGMII_TX_CLK_DELAY_SHIFT));
 
 		phy_write_mmd_indirect(phydev, DP83867_RGMIIDCTL,
 				       DP83867_DEVADDR, phydev->addr, delay);

@@ -221,6 +282,10 @@ static int dp83867_config(struct phy_device *phydev)
 
 	genphy_config_aneg(phydev);
 	return 0;
+
+err_out:
+	kfree(dp83867);
+	return ret;
 }
 

drivers/net/phy/ti.c static int dp83867_config(struct phy_device *phydev) · line 291

Quoted 2 lines

drivers/net/phy/ti.c +0 -0

 static struct phy_driver DP83867_driver = {

This patch is breaking 80 chars limit reported by checkpatch.

Thanks,
Michal

Quoted 76 lines · Michal Simek

Quoted 75 lines · Dan Murphy

Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default.

If devicetree is not used then use the default defines within the driver.

Signed-off-by Dan Murphy <[email protected]>

---

v4 - Rebased the driver and changed default values to -1

 drivers/net/phy/ti.c | 85 +++++++++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 75 insertions(+), 10 deletions(-)

drivers/net/phy/ti.c +33 -4

index 937426b..922f0a4 100644
@@ -6,6 +6,14 @@
  */
 #include <common.h>
 #include <phy.h>
+#include <linux/compat.h>
+#include <malloc.h>
+
+#include <fdtdec.h>
+#include <dm.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+DECLARE_GLOBAL_DATA_PTR;
 
 /* TI DP83867 */
 #define DP83867_DEVADDR		0x1f

@@ -71,6 +79,17 @@
 #define MII_MMD_CTRL_INCR_RDWT	0x8000 /* post increment on reads & writes */
 #define MII_MMD_CTRL_INCR_ON_WT	0xC000 /* post increment on writes only */
 
+/* User setting - can be taken from DTS */
+#define DEFAULT_RX_ID_DELAY	DP83867_RGMIIDCTL_2_25_NS
+#define DEFAULT_TX_ID_DELAY	DP83867_RGMIIDCTL_2_75_NS
+#define DEFAULT_FIFO_DEPTH	DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
+
+struct dp83867_private {
+	int rx_id_delay;
+	int tx_id_delay;
+	int fifo_depth;
+};
+
 /**
  * phy_read_mmd_indirect - reads data from the MMD registers
  * @phydev: The PHY device bus

@@ -148,16 +167,58 @@ static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
 		phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
 }
 
-/* User setting - can be taken from DTS */
-#define RX_ID_DELAY	8
-#define TX_ID_DELAY	0xa
-#define FIFO_DEPTH	1
+#if defined(CONFIG_DM_ETH)
+/**
+ * dp83867_data_init - Convenience function for setting PHY specific data
+ *
+ * @phydev: the phy_device struct
+ */
+static int dp83867_of_init(struct phy_device *phydev)
+{
+	struct dp83867_private *dp83867 = phydev->priv;
+	struct udevice *dev = phydev->dev;
+
+	dp83867->rx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,rx_internal_delay", -1);
+

Quoted 8 lines

drivers/net/phy/ti.c static inline bool phy_interface_is_rgmii(struct phy_device *phydev) · line 189

Quoted 6 lines

drivers/net/phy/ti.c +6 -0

+	dp83867->tx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,tx_internal_delay", -1);
+
+	dp83867->fifo_depth = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,fifo_depth", -1);
+

These names are still incompatible with binding you have. There are dashes instead of underscores.

OK fixed in new version.

Quoted 58 lines

Quoted 50 lines

drivers/net/phy/ti.c +28 -2

+	return 0;
+}
+#else
+static int dp83867_of_init(struct phy_device *phydev)
+{
+	dp83867->rx_id_delay = DEFAULT_RX_ID_DELAY;
+	dp83867->tx_id_delay = DEFAULT_TX_ID_DELAY;
+	dp83867->fifo_depth = DEFAULT_FIFO_DEPTH;
+
+	return 0;
+}
+#endif
 
 static int dp83867_config(struct phy_device *phydev)
 {
+	struct dp83867_private *dp83867;
 	unsigned int val, delay, cfg2;
 	int ret;
 
+	if (!phydev->priv) {
+		dp83867 = kzalloc(sizeof(*dp83867), GFP_KERNEL);
+		if (!dp83867)
+			return -ENOMEM;
+
+		phydev->priv = dp83867;
+		ret = dp83867_of_init(phydev);
+		if (ret)
+			goto err_out;
+	} else {
+		dp83867 = (struct dp83867_private *)phydev->priv;
+	}
+
 	/* Restart the PHY.  */
 	val = phy_read(phydev, MDIO_DEVAD_NONE, DP83867_CTRL);
 	phy_write(phydev, MDIO_DEVAD_NONE, DP83867_CTRL,

@@ -166,9 +227,9 @@ static int dp83867_config(struct phy_device *phydev)
 	if (phy_interface_is_rgmii(phydev)) {
 		ret = phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_PHYCTRL,
 			(DP83867_MDI_CROSSOVER_AUTO << DP83867_MDI_CROSSOVER) |
-			(FIFO_DEPTH << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
+			(dp83867->fifo_depth << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
 		if (ret)
-			return ret;
+			goto err_out;
 	} else {
 		phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR,
 			  (BMCR_ANENABLE | BMCR_FULLDPLX | BMCR_SPEED1000));

drivers/net/phy/ti.c static int dp83867_config(struct phy_device *phydev) · line 254

Quoted 7 lines

drivers/net/phy/ti.c +2 -2

@@ -189,8 +250,8 @@ static int dp83867_config(struct phy_device *phydev)
 			  DP83867_PHYCTRL_SGMIIEN |
 			  (DP83867_MDI_CROSSOVER_MDIX <<
 			  DP83867_MDI_CROSSOVER) |
-			  (FIFO_DEPTH << DP83867_PHYCTRL_RXFIFO_SHIFT) |
-			  (FIFO_DEPTH  << DP83867_PHYCTRL_TXFIFO_SHIFT));
+			  (dp83867->fifo_depth << DP83867_PHYCTRL_RXFIFO_SHIFT) |
+			  (dp83867->fifo_depth  << DP83867_PHYCTRL_TXFIFO_SHIFT));

                                              ^^

Quoted 1 line

Here are 2 spaces instead of 1

Removed

Quoted 25 lines

Quoted 25 lines

drivers/net/phy/ti.c +6 -2

 		phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_BISCR, 0x0);
 	}
 

@@ -212,8 +273,8 @@ static int dp83867_config(struct phy_device *phydev)
 		phy_write_mmd_indirect(phydev, DP83867_RGMIICTL,
 				       DP83867_DEVADDR, phydev->addr, val);
 
-		delay = (RX_ID_DELAY |
-			 (TX_ID_DELAY << DP83867_RGMII_TX_CLK_DELAY_SHIFT));
+		delay = (dp83867->rx_id_delay |
+			 (dp83867->tx_id_delay << DP83867_RGMII_TX_CLK_DELAY_SHIFT));
 
 		phy_write_mmd_indirect(phydev, DP83867_RGMIIDCTL,
 				       DP83867_DEVADDR, phydev->addr, delay);

@@ -221,6 +282,10 @@ static int dp83867_config(struct phy_device *phydev)
 
 	genphy_config_aneg(phydev);
 	return 0;
+
+err_out:
+	kfree(dp83867);
+	return ret;
 }
 

Quoted 3 lines

drivers/net/phy/ti.c static int dp83867_config(struct phy_device *phydev) · line 291

Quoted 2 lines

drivers/net/phy/ti.c +0 -0

 static struct phy_driver DP83867_driver = {

This patch is breaking 80 chars limit reported by checkpatch.

80 char limit is not an Error it is a Warning.
Well this is up to the maintainer. This is the way the driver is written in the kernel.

I want to keep the uboot file as close to the way I wrote it in the kernel. The same warnings appear in the kernel code and this was accepted

Quoted 85 lines · Dan Murphy

Quoted 84 lines · Michal Simek

Quoted 71 lines · Dan Murphy

Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default.

If devicetree is not used then use the default defines within the driver.

Signed-off-by Dan Murphy <[email protected]>

---

v4 - Rebased the driver and changed default values to -1

 drivers/net/phy/ti.c | 85 +++++++++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 75 insertions(+), 10 deletions(-)

drivers/net/phy/ti.c +29 -4

index 937426b..922f0a4 100644
@@ -6,6 +6,14 @@
  */
 #include <common.h>
 #include <phy.h>
+#include <linux/compat.h>
+#include <malloc.h>
+
+#include <fdtdec.h>
+#include <dm.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+DECLARE_GLOBAL_DATA_PTR;
 
 /* TI DP83867 */
 #define DP83867_DEVADDR		0x1f

@@ -71,6 +79,17 @@
 #define MII_MMD_CTRL_INCR_RDWT	0x8000 /* post increment on reads & writes */
 #define MII_MMD_CTRL_INCR_ON_WT	0xC000 /* post increment on writes only */
 
+/* User setting - can be taken from DTS */
+#define DEFAULT_RX_ID_DELAY	DP83867_RGMIIDCTL_2_25_NS
+#define DEFAULT_TX_ID_DELAY	DP83867_RGMIIDCTL_2_75_NS
+#define DEFAULT_FIFO_DEPTH	DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
+
+struct dp83867_private {
+	int rx_id_delay;
+	int tx_id_delay;
+	int fifo_depth;
+};
+
 /**
  * phy_read_mmd_indirect - reads data from the MMD registers
  * @phydev: The PHY device bus

@@ -148,16 +167,58 @@ static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
 		phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
 }
 
-/* User setting - can be taken from DTS */
-#define RX_ID_DELAY	8
-#define TX_ID_DELAY	0xa
-#define FIFO_DEPTH	1
+#if defined(CONFIG_DM_ETH)
+/**
+ * dp83867_data_init - Convenience function for setting PHY specific data
+ *
+ * @phydev: the phy_device struct
+ */
+static int dp83867_of_init(struct phy_device *phydev)
+{
+	struct dp83867_private *dp83867 = phydev->priv;
+	struct udevice *dev = phydev->dev;

drivers/net/phy/ti.c static inline bool phy_interface_is_rgmii(struct phy_device *phydev) · line 189

Quoted 10 lines

drivers/net/phy/ti.c +10 -0

+
+	dp83867->rx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,rx_internal_delay", -1);
+
+	dp83867->tx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,tx_internal_delay", -1);
+
+	dp83867->fifo_depth = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+				 "ti,fifo_depth", -1);
+

These names are still incompatible with binding you have. There are dashes instead of underscores.

Quoted 1 line

OK fixed in new version.

Move the phy_interface_is_rgmii to the phy.h
file for all phy's to be able to use the API.

This now aligns with the Linux kernel based on
commit e463d88c36d42211aa72ed76d32fb8bf37820ef1

Signed-off-by Dan Murphy <[email protected]>

Move the phy_interface_is_rgmii to the phy.h
file for all phy's to be able to use the API.

This now aligns with the Linux kernel based on
commit e463d88c36d42211aa72ed76d32fb8bf37820ef1

Signed-off-by Dan Murphy <[email protected]>

---
 drivers/net/phy/ti.c | 11 -----------
 include/phy.h        | 11 +++++++++++
 2 files changed, 11 insertions(+), 11 deletions(-)

drivers/net/phy/ti.c +0 -11

index 922f0a4..d503eef 100644
@@ -156,17 +156,6 @@ void phy_write_mmd_indirect(struct phy_device *phydev, int prtad,
 	phy_write(phydev, addr, MII_MMD_DATA, data);
 }
 
-/**
- * phy_interface_is_rgmii - Convenience function for testing if a PHY interface
- * is RGMII (all variants)
- * @phydev: the phy_device struct
- */
-static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
-{
-	return phydev->interface >= PHY_INTERFACE_MODE_RGMII &&
-		phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
-}
-
 #if defined(CONFIG_DM_ETH)
 /**
  * dp83867_data_init - Convenience function for setting PHY specific data

include/phy.h +4 -0

index 21459a8..7b2d1ff 100644
@@ -277,6 +277,17 @@ int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id);
  */
 int phy_get_interface_by_name(const char *str);
 
+/**
+ * phy_interface_is_rgmii - Convenience function for testing if a PHY interface
+ * is RGMII (all variants)
+ * @phydev: the phy_device struct

Add a helper to phy.h to identify whether the
phy is configured for SGMII all variables.

Signed-off-by Dan Murphy <[email protected]>

Add a helper to phy.h to identify whether the
phy is configured for SGMII all variables.

Signed-off-by Dan Murphy <[email protected]>

---
 include/phy.h | 11 +++++++++++
 1 file changed, 11 insertions(+)

include/phy.h +4 -0

index 7b2d1ff..ef3eb51 100644
@@ -288,6 +288,17 @@ static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
 		phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
 }
 
+/**
+ * phy_interface_is_sgmii - Convenience function for testing if a PHY interface
+ * is SGMII (all variants)
+ * @phydev: the phy_device struct

The code assumed that if the interface is not RGMII configured then it must be SGMII configured. This device has the ability to support most of the MII interfaces. Therefore add the helper for SGMII and only configure the device if the interface is configured for SGMII.

Signed-off-by Dan Murphy <[email protected]>

The code assumed that if the interface is not RGMII configured then it must be SGMII configured. This device has the ability to support most of the MII interfaces. Therefore add the helper for SGMII and only configure the device if the interface is configured for SGMII.

Signed-off-by Dan Murphy <[email protected]>

---
 drivers/net/phy/ti.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

drivers/net/phy/ti.c +0 -0

index d503eef..4402c52 100644

Add the ability to read the phy-handle node of the cpsw slave. Upon reading this handle the phy-id can be stored based on the reg node in the DT.

The phy-handle also needs to be stored and passed to the phy to access any phy data that is available.

Signed-off-by Dan Murphy <[email protected]>

Add the ability to read the phy-handle node of the cpsw slave. Upon reading this handle the phy-id can be stored based on the reg node in the DT.

The phy-handle also needs to be stored and passed to the phy to access any phy data that is available.

Signed-off-by Dan Murphy <[email protected]>

---
 drivers/net/cpsw.c | 18 ++++++++++++++++--
 include/cpsw.h     |  1 +
 2 files changed, 17 insertions(+), 2 deletions(-)