Skip to contentSkip to conversation

Configuring a Bluetooth PAN server: can't find docs

DISCUSSION Egbert van der Wal 2 participants 3 messages Apr 1, 2016 – Apr 24, 2016 Bluetooth drivers

lore
Share & tools
lore
#0 lore raw

Hi,

Short story: I'd really like to RTFM, but in all of my online quests I can't find where it is. Where can I find documentation about bluez, configuration files and pand?

With a bit more information: I'm trying to configure a device (Odroid XU4 running Ubuntu 14.04, using Bluez 4.101) to accept PAN-connections. Doing this I want to provide the connecting user with a web interface to perform some configuration tasks (such as connecting to a wifi).

The resulting connection will not provide internet access and will only be used to expose access to an internal IP address (e.g. 10.0.0.1). I want the device to basically accept any pairing request using a fixed, pre-configured pin-code.

I've been trying to get this working for a while now using various howto's but it seems to me that each and every one of them uses a different way to configure Bluez, probably resulting from a different version. I basically tried all of them and none seem to work (due to missing / invalid commands or missing / ignored configuration files).

I couldn't find any documentation on bluez.org itself. The bluetoothd man-page refers to a man-page of /etc/bluetooth/main.conf that doesn't seem to exist, and the contents of /etc/bluetooth/main.conf also seem to be ignored so I'm quite stuck here.

Any pointers to any type of documentation that covers my version of bluez and the steps to set this up would be highly appreciated.

Thanks in advance!

Regards,

Egbert

#1 lore raw

Hi Egbert,

Quoted 10 lines · Egbert van der Wal

Hi,

Short story: I'd really like to RTFM, but in all of my online quests I can't find where it is. Where can I find documentation about bluez, configuration files and pand?

With a bit more information: I'm trying to configure a device (Odroid XU4 running Ubuntu 14.04, using Bluez 4.101) to accept PAN-connections. Doing this I want to provide the connecting user with a web interface to perform some configuration tasks (such as connecting to a wifi).

Unfortunately 4.101 is a bit too old and I guess even NetworkManager does support that.

Quoted 10 lines

The resulting connection will not provide internet access and will only be used to expose access to an internal IP address (e.g. 10.0.0.1). I want the device to basically accept any pairing request using a fixed, pre-configured pin-code.

I've been trying to get this working for a while now using various howto's but it seems to me that each and every one of them uses a different way to configure Bluez, probably resulting from a different version. I basically tried all of them and none seem to work (due to missing / invalid commands or missing / ignored configuration files).

Have you tried connman tethering? https://01.org/connman/documentation

Quoted 4 lines

I couldn't find any documentation on bluez.org itself. The bluetoothd man-page refers to a man-page of /etc/bluetooth/main.conf that doesn't seem to exist, and the contents of /etc/bluetooth/main.conf also seem to be ignored so I'm quite stuck here.

https://git.kernel.org/cgit/bluetooth/bluez.git/tree/doc/network-api.txt

Quoted 3 lines

Any pointers to any type of documentation that covers my version of bluez and the steps to set this up would be highly appreciated.

Create a bridge and pass it to org.bluez.NetworkServer1.Register, the process need to remain connected to D-Bus otherwise it will be unregistered, but other than that it should be really simple.

Quoted 11 lines

Thanks in advance!

Regards,

Egbert

--
To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 1 line
Luiz Augusto von Dentz
#2 lore raw

Op 05-04-16 om 17:03 schreef Luiz Augusto von Dentz:

Quoted 32 lines

Hi Egbert,

Quoted 10 lines · Egbert van der Wal

Hi,

Short story: I'd really like to RTFM, but in all of my online quests I can't find where it is. Where can I find documentation about bluez, configuration files and pand?

With a bit more information: I'm trying to configure a device (Odroid XU4 running Ubuntu 14.04, using Bluez 4.101) to accept PAN-connections. Doing this I want to provide the connecting user with a web interface to perform some configuration tasks (such as connecting to a wifi).

Unfortunately 4.101 is a bit too old and I guess even NetworkManager does support that.

Quoted 10 lines

The resulting connection will not provide internet access and will only be used to expose access to an internal IP address (e.g. 10.0.0.1). I want the device to basically accept any pairing request using a fixed, pre-configured pin-code.

I've been trying to get this working for a while now using various howto's but it seems to me that each and every one of them uses a different way to configure Bluez, probably resulting from a different version. I basically tried all of them and none seem to work (due to missing / invalid commands or missing / ignored configuration files).

Have you tried connman tethering? https://01.org/connman/documentation

Quoted 4 lines

I couldn't find any documentation on bluez.org itself. The bluetoothd man-page refers to a man-page of /etc/bluetooth/main.conf that doesn't seem to exist, and the contents of /etc/bluetooth/main.conf also seem to be ignored so I'm quite stuck here.

Quoted 8 lines

https://git.kernel.org/cgit/bluetooth/bluez.git/tree/doc/network-api.txt

Quoted 2 lines

Any pointers to any type of documentation that covers my version of bluez and the steps to set this up would be highly appreciated.

Create a bridge and pass it to org.bluez.NetworkServer1.Register, the process need to remain connected to D-Bus otherwise it will be unregistered, but other than that it should be really simple.

Hi Luiz,

Thank you for the suggestion. The link you provided is a link to an API, not a link to documentation for the entire package and how all parts interoperate, including the available software utilities. Am I correct in concluding that such documentation does not exist, from an official source?

Anyway, I have been able to collect several bits and pieces from more forums and now have been able to create a Bluetooth NAP using the bt-network tool. The name of that tool was basically was I was looking for, combined with some documentation on how to set up the bridge that it works with.

BlueZ 4.101 is the latest version available on Ubuntu 14.04, the most recent LTS distribution of Ubuntu until a couple of days ago, so in that sense, it really isn't that old. And it turns out that NetworkManager is able to interface with BlueZ 4.101 on the other end fine in order to connect to the NAP.

Again, thanks for the help. I've been able to achieve what I attempted.

Kind regards,

Egbert van der Wal