hwmon: (tmp401) Add support for TI TMP461

Signed-off-by Andrew F. Davis <[email protected]>

---
  Documentation/hwmon/tmp401 | 18 +++++++++--
  drivers/hwmon/Kconfig      |  2 +-
  drivers/hwmon/tmp401.c     | 81 ++++++++++++++++++++++++++++++++++++++++++----
  3 files changed, 92 insertions(+), 9 deletions(-)

Documentation/hwmon/tmp401 +5 -2

index 711f75e..eaa2d3b 100644
@@ -22,6 +22,9 @@ Supported chips:
      Prefix: 'tmp435'
      Addresses scanned: I2C 0x48 - 0x4f
      Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp435.html
+  * Texas Instruments TMP461
+    Prefix: 'tmp461'
+    Datasheet: http://www.ti.com/product/tmp461
 
  Authors:
           Hans de Goede <[email protected]>

@@ -31,8 +34,8 @@ Description
  -----------
 
  This driver implements support for Texas Instruments TMP401, TMP411,
-TMP431, TMP432 and TMP435 chips. These chips implement one or two remote
-and one local temperature sensors. Temperature is measured in degrees
+TMP431, TMP432, TMP435, and TMP461 chips. These chips implement one or two
+remote and one local temperature sensors. Temperature is measured in degrees
  Celsius. Resolution of the remote sensor is 0.0625 degree. Local
  sensor resolution can be set to 0.5, 0.25, 0.125 or 0.0625 degree (not
  supported by the driver so far, so using the default resolution of 0.5

@@ -55,3 +58,14 @@ some additional features.
 
  TMP432 is compatible with TMP401 and TMP431. It supports two external
  temperature sensors.

Documentation/hwmon/tmp401 +1 -0

+  Exported via sysfs attribute tempX_nfactor

drivers/hwmon/Kconfig +1 -1

index ff94007..c571dcf 100644
@@ -1561,7 +1561,7 @@ config SENSORS_TMP401
  	depends on I2C
  	help
  	  If you say yes here you get support for Texas Instruments TMP401,
-	  TMP411, TMP431, TMP432 and TMP435 temperature sensor chips.
+	  TMP411, TMP431, TMP432, TMP435, and TMP461 temperature sensor chips.
 
  	  This driver can also be built as a module.  If so, the module
  	  will be called tmp401.

drivers/hwmon/tmp401.c +0 -0

index ccf4cff..280065b 100644

drivers/hwmon/tmp401.c +9 -3

  /*
   * The TMP401 registers, note some registers have different addresses for

@@ -62,31 +63,37 @@ enum chips { tmp401, tmp411, tmp431, tmp432, tmp435 };
  #define TMP401_MANUFACTURER_ID_REG		0xFE
  #define TMP401_DEVICE_ID_REG			0xFF
 
-static const u8 TMP401_TEMP_MSB_READ[6][2] = {
+static const u8 TMP401_TEMP_MSB_READ[8][2] = {
  	{ 0x00, 0x01 },	/* temp */
  	{ 0x06, 0x08 },	/* low limit */
  	{ 0x05, 0x07 },	/* high limit */
  	{ 0x20, 0x19 },	/* therm (crit) limit */
  	{ 0x30, 0x34 },	/* lowest */
  	{ 0x32, 0x36 },	/* highest */
+	{ 0, 0x11 },	/* offset */
+	{ 0, 0x23 },	/* nfactor */
  };
 
-static const u8 TMP401_TEMP_MSB_WRITE[6][2] = {
+static const u8 TMP401_TEMP_MSB_WRITE[8][2] = {
  	{ 0, 0 },	/* temp (unused) */
  	{ 0x0C, 0x0E },	/* low limit */
  	{ 0x0B, 0x0D },	/* high limit */
  	{ 0x20, 0x19 },	/* therm (crit) limit */
  	{ 0x30, 0x34 },	/* lowest */
  	{ 0x32, 0x36 },	/* highest */
+	{ 0, 0x11 },	/* offset */
+	{ 0, 0x23 },	/* nfactor */
  };
 
-static const u8 TMP401_TEMP_LSB[6][2] = {
+static const u8 TMP401_TEMP_LSB[8][2] = {
  	{ 0x15, 0x10 },	/* temp */
  	{ 0x17, 0x14 },	/* low limit */
  	{ 0x16, 0x13 },	/* high limit */
  	{ 0, 0 },	/* therm (crit) limit (unused) */
  	{ 0x31, 0x35 },	/* lowest */
  	{ 0x33, 0x37 },	/* highest */
+	{ 0, 0x12 },	/* offset */
+	{ 0, 0 },	/* nfactor (unused) */
  };
 
  static const u8 TMP432_TEMP_MSB_READ[4][3] = {

drivers/hwmon/tmp401.c +63 -2

  	{ }
  };
  MODULE_DEVICE_TABLE(i2c, tmp401_id);

@@ -170,7 +178,7 @@ struct tmp401_data {
  	/* register values */
  	u8 status[4];
  	u8 config;
-	u16 temp[6][3];
+	u16 temp[8][3];
  	u8 temp_crit_hyst;
  };
 

@@ -445,6 +453,44 @@ static ssize_t reset_temp_history(struct device *dev,
  	return count;
  }
 
+static ssize_t show_nfactor(struct device *dev,
+			    struct device_attribute *devattr, char *buf)
+{
+	int nr = to_sensor_dev_attr_2(devattr)->nr;
+	int index = to_sensor_dev_attr_2(devattr)->index;
+	struct tmp401_data *data = tmp401_update_device(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%d\n", data->temp[nr][index]);
+}
+
+static ssize_t store_nfactor(struct device *dev,
+			     struct device_attribute *devattr,
+			     const char *buf, size_t count)
+{
+	int nr = to_sensor_dev_attr_2(devattr)->nr;
+	int index = to_sensor_dev_attr_2(devattr)->index;
+	struct tmp401_data *data = dev_get_drvdata(dev);
+	struct i2c_client *client = data->client;
+	long val;
+	u8 regaddr;
+
+	if (kstrtol(buf, 10, &val))
+		return -EINVAL;
+	val = clamp_val(val, -128, 127);
+
+	regaddr = TMP401_TEMP_MSB_WRITE[nr][index];
+
+	mutex_lock(&data->update_lock);
+	i2c_smbus_write_byte_data(client, regaddr, val);
+	data->temp[nr][index] = val;
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
  static ssize_t show_update_interval(struct device *dev,
  				    struct device_attribute *attr, char *buf)
  {

@@ -613,6 +659,26 @@ static const struct attribute_group tmp432_group = {
  };
 
  /*
+ * Additional features of the TMP461 chip.
+ * The TMP461 η-factor correction and temperature offset
+ * for the remote channel.
+ */
+static SENSOR_DEVICE_ATTR_2(temp2_offset, S_IWUSR | S_IRUGO, show_temp,
+			    store_temp, 6, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_nfactor, S_IWUSR | S_IRUGO, show_nfactor,
+			    store_nfactor, 7, 1);
+
+static struct attribute *tmp461_attributes[] = {
+	&sensor_dev_attr_temp2_offset.dev_attr.attr,
+	&sensor_dev_attr_temp2_nfactor.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group tmp461_group = {
+	.attrs = tmp461_attributes,
+};
+
+/*
   * Begin non sysfs callback code (aka Real code)
   */
 

@@ -714,7 +780,7 @@ static int tmp401_probe(struct i2c_client *client,
  			const struct i2c_device_id *id)
  {
  	static const char * const names[] = {
-		"TMP401", "TMP411", "TMP431", "TMP432", "TMP435"
+		"TMP401", "TMP411", "TMP431", "TMP432", "TMP435", "TMP461"
  	};
  	struct device *dev = &client->dev;
  	struct device *hwmon_dev;

@@ -745,6 +811,9 @@ static int tmp401_probe(struct i2c_client *client,
  	if (data->kind == tmp432)
  		data->groups[groups++] = &tmp432_group;
 
+	if (data->kind == tmp461)
+		data->groups[groups++] = &tmp461_group;
+
  	hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
  							   data, data->groups);
  	if (IS_ERR(hwmon_dev))

Quoted 49 lines · Andrew F. Davis

Signed-off-by Andrew F. Davis <[email protected]>

---
  Documentation/hwmon/tmp401 | 18 +++++++++--
  drivers/hwmon/Kconfig      |  2 +-
  drivers/hwmon/tmp401.c     | 81
++++++++++++++++++++++++++++++++++++++++++----
  3 files changed, 92 insertions(+), 9 deletions(-)

Documentation/hwmon/tmp401 +4 -2

index 711f75e..eaa2d3b 100644
@@ -22,6 +22,9 @@ Supported chips:
      Prefix: 'tmp435'
      Addresses scanned: I2C 0x48 - 0x4f
      Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp435.html
+  * Texas Instruments TMP461
+    Prefix: 'tmp461'
+    Datasheet: http://www.ti.com/product/tmp461
 
  Authors:
           Hans de Goede <[email protected]>

@@ -31,8 +34,8 @@ Description
  -----------
 
  This driver implements support for Texas Instruments TMP401, TMP411,
-TMP431, TMP432 and TMP435 chips. These chips implement one or two remote
-and one local temperature sensors. Temperature is measured in degrees
+TMP431, TMP432, TMP435, and TMP461 chips. These chips implement one

or two
+remote and one local temperature sensors. Temperature is measured in degrees
Celsius. Resolution of the remote sensor is 0.0625 degree. Local sensor resolution can be set to 0.5, 0.25, 0.125 or 0.0625 degree (not supported by the driver so far, so using the default resolution of 0.5

Documentation/hwmon/tmp401 +2 -0

@@ -55,3 +58,14 @@ some additional features.
 
  TMP432 is compatible with TMP401 and TMP431. It supports two external
  temperature sensors.
+
+TMP461 is compatible with TMP401. It supports offset and n-factor

correction

Documentation/hwmon/tmp401 +7 -0

+that is applied to the remote sensor.
+
+* Sensor offset values are temperature values
+
+  Exported via sysfs attribute tempX_offset
+
+* n-factor correction, values are in raw form as described in the

Quoted 2 lines

datasheet
+

If you don't mind, I would prefer if you would drop this attribute, at least
for now, for a number of reasons. It should not really be controlled by a sysfs
attribute, but either with devicetree data or platform data. Exposing a raw register value through sysfs isn't really desirable; sysfs is supposed

to provide some kind of abstraction. It enables setting the n-factor, but not beta-compensation which is probably equally desirable. Last but not least, other chips supported by this driver, as well as other chips
supported by hwmon, also support n-factor correction and beta-compensation.
If we provide this functionality we should provide it for all chips in a generic way. In short, this needs more discussion.

Couple of additional additional comments below.

Thanks,
Guenter

Quoted 24 lines

Documentation/hwmon/tmp401 +1 -0

+  Exported via sysfs attribute tempX_nfactor

drivers/hwmon/Kconfig +1 -1

index ff94007..c571dcf 100644
@@ -1561,7 +1561,7 @@ config SENSORS_TMP401
      depends on I2C
      help
        If you say yes here you get support for Texas Instruments TMP401,
-      TMP411, TMP431, TMP432 and TMP435 temperature sensor chips.
+      TMP411, TMP431, TMP432, TMP435, and TMP461 temperature sensor

chips.

This driver can also be built as a module. If so, the module will be called tmp401.

drivers/hwmon/tmp401.c +0 -0

index ccf4cff..280065b 100644
@@ -47,7 +47,8 @@
  static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4c,
 0x4d,
      0x4e, 0x4f, I2C_CLIENT_END };
 

drivers/hwmon/tmp401.c line 52

Quoted 4 lines

drivers/hwmon/tmp401.c +2 -1

-enum chips { tmp401, tmp411, tmp431, tmp432, tmp435 };
+enum chips { tmp401, tmp411, tmp431, tmp432, tmp435, tmp461 };
+
 

Please no double empty lines.

Quoted 44 lines

drivers/hwmon/tmp401.c +0 -0

  /*

* The TMP401 registers, note some registers have different
addresses for

drivers/hwmon/tmp401.c +9 -3

@@ -62,31 +63,37 @@ enum chips { tmp401, tmp411, tmp431, tmp432,
 tmp435 };
  #define TMP401_MANUFACTURER_ID_REG        0xFE
  #define TMP401_DEVICE_ID_REG            0xFF
 
-static const u8 TMP401_TEMP_MSB_READ[6][2] = {
+static const u8 TMP401_TEMP_MSB_READ[8][2] = {
      { 0x00, 0x01 },    /* temp */
      { 0x06, 0x08 },    /* low limit */
      { 0x05, 0x07 },    /* high limit */
      { 0x20, 0x19 },    /* therm (crit) limit */
      { 0x30, 0x34 },    /* lowest */
      { 0x32, 0x36 },    /* highest */
+    { 0, 0x11 },    /* offset */
+    { 0, 0x23 },    /* nfactor */
  };
 
-static const u8 TMP401_TEMP_MSB_WRITE[6][2] = {
+static const u8 TMP401_TEMP_MSB_WRITE[8][2] = {
      { 0, 0 },    /* temp (unused) */
      { 0x0C, 0x0E },    /* low limit */
      { 0x0B, 0x0D },    /* high limit */
      { 0x20, 0x19 },    /* therm (crit) limit */
      { 0x30, 0x34 },    /* lowest */
      { 0x32, 0x36 },    /* highest */
+    { 0, 0x11 },    /* offset */
+    { 0, 0x23 },    /* nfactor */
  };
 
-static const u8 TMP401_TEMP_LSB[6][2] = {
+static const u8 TMP401_TEMP_LSB[8][2] = {
      { 0x15, 0x10 },    /* temp */
      { 0x17, 0x14 },    /* low limit */
      { 0x16, 0x13 },    /* high limit */
      { 0, 0 },    /* therm (crit) limit (unused) */
      { 0x31, 0x35 },    /* lowest */
      { 0x33, 0x37 },    /* highest */
+    { 0, 0x12 },    /* offset */
+    { 0, 0 },    /* nfactor (unused) */
  };
 

drivers/hwmon/tmp401.c static const struct i2c_device_id tmp401_id[] = { · line 159

Quoted 6 lines

  static const u8 TMP432_TEMP_MSB_READ[4][3] = {

drivers/hwmon/tmp401.c +1 -0

@@ -149,6 +156,7 @@ static const struct i2c_device_id tmp401_id[] = {
      { "tmp431", tmp431 },
      { "tmp432", tmp432 },
      { "tmp435", tmp435 },
+    { "tmp461", tmp461 },

Please also provide code in the detect function to auto-detect the chip.

Quoted 107 lines

drivers/hwmon/tmp401.c +39 -1

      { }
  };
  MODULE_DEVICE_TABLE(i2c, tmp401_id);

@@ -170,7 +178,7 @@ struct tmp401_data {
      /* register values */
      u8 status[4];
      u8 config;
-    u16 temp[6][3];
+    u16 temp[8][3];
      u8 temp_crit_hyst;
  };
 

@@ -445,6 +453,44 @@ static ssize_t reset_temp_history(struct device
 *dev,
      return count;
  }
 
+static ssize_t show_nfactor(struct device *dev,
+                struct device_attribute *devattr, char *buf)
+{
+    int nr = to_sensor_dev_attr_2(devattr)->nr;
+    int index = to_sensor_dev_attr_2(devattr)->index;
+    struct tmp401_data *data = tmp401_update_device(dev);
+
+    if (IS_ERR(data))
+        return PTR_ERR(data);
+
+    return sprintf(buf, "%d\n", data->temp[nr][index]);
+}
+
+static ssize_t store_nfactor(struct device *dev,
+                 struct device_attribute *devattr,
+                 const char *buf, size_t count)
+{
+    int nr = to_sensor_dev_attr_2(devattr)->nr;
+    int index = to_sensor_dev_attr_2(devattr)->index;
+    struct tmp401_data *data = dev_get_drvdata(dev);
+    struct i2c_client *client = data->client;
+    long val;
+    u8 regaddr;
+
+    if (kstrtol(buf, 10, &val))
+        return -EINVAL;
+    val = clamp_val(val, -128, 127);
+
+    regaddr = TMP401_TEMP_MSB_WRITE[nr][index];
+
+    mutex_lock(&data->update_lock);
+    i2c_smbus_write_byte_data(client, regaddr, val);
+    data->temp[nr][index] = val;
+    mutex_unlock(&data->update_lock);
+
+    return count;
+}
+
  static ssize_t show_update_interval(struct device *dev,
                      struct device_attribute *attr, char *buf)

  {

drivers/hwmon/tmp401.c +24 -1

@@ -613,6 +659,26 @@ static const struct attribute_group tmp432_group = {
  };
 
  /*
+ * Additional features of the TMP461 chip.
+ * The TMP461 η-factor correction and temperature offset
+ * for the remote channel.
+ */
+static SENSOR_DEVICE_ATTR_2(temp2_offset, S_IWUSR | S_IRUGO, show_temp,
+                store_temp, 6, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_nfactor, S_IWUSR | S_IRUGO,
 show_nfactor,
+                store_nfactor, 7, 1);
+
+static struct attribute *tmp461_attributes[] = {
+    &sensor_dev_attr_temp2_offset.dev_attr.attr,
+    &sensor_dev_attr_temp2_nfactor.dev_attr.attr,
+    NULL
+};
+
+static const struct attribute_group tmp461_group = {
+    .attrs = tmp461_attributes,
+};
+
+/*
   * Begin non sysfs callback code (aka Real code)
   */

@@ -714,7 +780,7 @@ static int tmp401_probe(struct i2c_client *client,
              const struct i2c_device_id *id)
  {
      static const char * const names[] = {
-        "TMP401", "TMP411", "TMP431", "TMP432", "TMP435"
+        "TMP401", "TMP411", "TMP431", "TMP432", "TMP435", "TMP461"
      };
      struct device *dev = &client->dev;
      struct device *hwmon_dev;

@@ -745,6 +811,9 @@ static int tmp401_probe(struct i2c_client *client,
      if (data->kind == tmp432)
          data->groups[groups++] = &tmp432_group;
 
+    if (data->kind == tmp461)
+        data->groups[groups++] = &tmp461_group;
+
      hwmon_dev = devm_hwmon_device_register_with_groups(dev,
 client->name,
                                 data, data->groups);

      if (IS_ERR(hwmon_dev))

Quoted 9 lines

drivers/hwmon/tmp401.c static const struct i2c_device_id tmp401_id[] = { · line 159

Quoted 6 lines

  static const u8 TMP432_TEMP_MSB_READ[4][3] = {

drivers/hwmon/tmp401.c +1 -0

@@ -149,6 +156,7 @@ static const struct i2c_device_id tmp401_id[] = {
      { "tmp431", tmp431 },
      { "tmp432", tmp432 },
      { "tmp435", tmp435 },
+    { "tmp461", tmp461 },

Please also provide code in the detect function to auto-detect the chip.

It looks like the ID reg has been removed (at least from the datasheet) so I'm not sure there is any good way to ID this part.