ARM: dts: imx6q: extend support for the cm-fx6

index 21c513f..c6f0e58 100644
@@ -12,6 +12,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "imx6q.dtsi"
 
 / {

@@ -31,6 +32,49 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	reg_pcie_power_on_gpio: regulator-pcie-power-on-gpio {
+		compatible = "regulator-fixed";
+		regulator-name = "regulator-pcie-power-on-gpio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_h1_vbus: usb_h1_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg_vbus: usb_otg_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ecspi1 {
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	m25p80 at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
 };
 
 &fec {

@@ -46,7 +90,30 @@
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+	clock-frequency = <100000>;
+
+	eeprom at 50 {
+		compatible = "at24,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
 &iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK	0x100b1
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO	0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI	0x100b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30	0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19	0x100b1
+		>;
+	};
+
 	pinctrl_enet: enetgrp {
 		fsl,pins = <
 			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0

@@ -90,12 +157,55 @@
 		>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x1b0b1
+		>;
+	};
+
 	pinctrl_uart4: uart4grp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
 			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
 		>;
 	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x130b0
+		>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+	vdd-supply = <&reg_pcie_power_on_gpio>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
 };
 
 &uart4 {

@@ -103,3 +213,18 @@
 	pinctrl-0 = <&pinctrl_uart4>;
 	status = "okay";
 };
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	dr_mode = "otg";
+	status = "okay";
+};

index 515a428..287044c 100644
@@ -369,6 +369,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-tx6q-1110.dtb \
 	imx6q-tx6q-11x0-mb7.dtb \
 	imx6q-udoo.dtb \
+	imx6q-utilite-pro.dtb \
 	imx6q-wandboard.dtb \
 	imx6q-wandboard-revb1.dtb \
 	imx6qp-nitrogen6_max.dtb \

153 lines not on this page · raw message

index c6f0e58..fe2c868 100644
@@ -3,12 +3,42 @@
  *
  * Author: Valentin Raevsky <[email protected]>
  *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
  *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;