Skip to contentSkip to conversation

clocksource/drivers/clksrc-of: Improve error handling

PATCH In review Daniel Lezcano 26 participants 125 messages Jun 16, 2016 – Jun 26, 2016

Subsystems (31)
lore
Share & tools
lore
#0 lore raw

v2 cover clocksource/drivers/clksrc-of: Improve error handling

First of all, I apologize for the size of this series. The changes are always going on the same direction and apply for the same init function in the different drivers.

The macro CLOCKSOURCE_OF_DECLARE is widely used in the timer drivers.

Basically, this macro is defined to insert in a table a tuple name,function. This function is an init function called when the name matches the DT node and its signature is:

        typedef void (*of_init_fn_1)(struct device_node *);

It does not return an error code.

That results in the clocksource-probe not being able to figure out if the driver was correctly initialized or not, the different drivers to act as they were the only ones on the system (panic, instead of failing gracefully), and duplicated code for error reporting.

This series initiates the logic change and centralize the error handling in the clocksource probe code.

In order to do the changes little by little, a new macro was introduced:

CLOCKSOURCE_OF_DECLARE_RET()

It expects an init function signature:

        typedef int (*of_init_ret_fn_1)(struct device_node *);

When all drivers have their init functions signature changed to return a value, CLOCKSOURCE_OF_DECLARE_RET changes its name back to CLOCKSOURCE_OF_DECLARE, so the entire patchset is git-bisect safe.

Changelog:

V2:
- Added Reviewed-by tags
- Added all the clocksource drivers changes, so the series contains the entire conversion of the init function returning an error code
- Some fixes reported by the automated compilation bots
V1:
- initial post

Daniel Lezcano (63):
of: Add a new macro to declare_of for one parameter function returning
a value
clocksource/drivers/clksrc-probe: Introduce init functions with return
code
clocksource/drivers/rockchip_timer: Convert init function to return
error
clocksource/drivers/mkt_timer: Convert init function to return error clocksource/drivers/exynos_mct: Convert init function to return error clocksource/drivers/asm9260: Convert init function to return error clocksource/drivers/cadence_ttc: Convert init function to return error clocksource/drivers/st_lpc: Convert init function to return error clocksource/drivers/dw_apb_timer: Convert init function to return
error
clocksource/drivers/clps711x: Convert init function to return error clocksource/drivers/digitcolor: Convert init function to return error clocksource/drivers/armv7m_systick: Convert init function to return
error
clocksource/drivers/bcm2835_timer: Convert init function to return
error
clocksource/drivers/bcm_kona: Convert init function to return error clocksource/drivers/clksrc-dbx500: Convert init function to return
error
clocksource/drivers/fsl_ftm_timer: Convert init function to return
error
clocksource/drivers/arm_arch_timer: Convert init function to return
error
clocksource/drivers/arm_global_timer: Convert init function to return
error
clocksource/drivers/h8300_timer16: Convert init function to return
error
clocksource/drivers/h8300_tpu: Convert init function to return error clocksource/drivers/h8300_tpu: Convert init function to return error clocksource/drivers/mips-gic-timer: Convert init function to return
error
clocksource/drivers/moxart_timer: Convert init function to return
error
clocksource/drivers/mps2-timer: Convert init function to return error clocksource/drivers/mxs_timer: Convert init function to return error clocksource/drivers/nomadik-mtu: Convert init function to return error clocksource/drivers/pxa_timer: Convert init function to return error clocksource/drivers/qcom-timer: Convert init function to return error clocksource/drivers/samsung_pwm_timer: Convert init function to return
error
clocksource/drivers/sun4i_time: Convert init function to return error clocksource/drivers/tango_xtal: Convert init function to return error clocksource/drivers/tegra20_timer: Convert init function to return
error
clocksource/drivers/time-armada-370-xp: Convert init function to
return error
clocksource/drivers/time-efm32: Convert init function to return error clocksource/drivers/time-lpc32xx: Convert init function to return
error
clocksource/drivers/time-orion: Convert init function to return error clocksource/drivers/time-pistachio: Convert init function to return
error
clocksource/drivers/time-pistachio: Convert init function to return
error
clocksource/drivers/timer-atlas7: Convert init function to return
error
clocksource/drivers/timer-atmel-pit: Convert init function to return
error
clocksource/drivers/timer-atmel-st: Convert init function to return
error
clocksource/drivers/prima2: Convert init function to return error clocksource/drivers/timer-imx-gpt: Convert init function to return
error
clocksource/drivers/timer-integrator-ap: Convert init function to
return error
clocksource/drivers/timer-keystone: Convert init function to return
error
clocksource/drivers/timer-sp804: Convert init function to return error clocksource/drivers/timer-stm32: Convert init function to return error clocksource/drivers/timer-sun5i: Convert init function to return error clocksource/drivers/timer-ti-32k: Convert init function to return
error
clocksource/drivers/timer-u300: Convert init function to return error clocksource/drivers/versatile: Convert init function to return error clocksource/drivers/vf_pit_timer: Convert init function to return
error
clocksource/drivers/vt8500_timer: Convert init function to return
error
clocksource/drivers/zevio-timer: Convert init function to return error clocksource/drivers/timer-sp804: Convert init function to return error clocksource/drivers/microblaze: Convert init function to return error clocksource/drivers/ralink: Convert init function to return error clocksource/drivers/nios2: Convert init function to return error clocksource/drivers/smp_twd: Convert init function to return error clocksource/drivers/nps: Convert init function to return error clocksource/drivers/arc: Convert init function to return error clocksource/drivers/oxnas-rps: Convert init function to return error
clocksources: Switch back to the clksrc table

 arch/arc/kernel/time.c                    | 63 ++++++++++++--------
 arch/arm/kernel/smp_twd.c                 |  3 +-
 arch/microblaze/kernel/timer.c            | 49 ++++++++++++----
 arch/mips/ralink/cevt-rt3352.c            | 17 ++++--
 arch/nios2/kernel/time.c                  | 67 ++++++++++++++-------
 drivers/clocksource/arm_arch_timer.c      | 46 +++++++++------
 drivers/clocksource/arm_global_timer.c    | 26 ++++++---
 drivers/clocksource/armv7m_systick.c      | 16 ++++--
 drivers/clocksource/asm9260_timer.c       | 22 ++++---
 drivers/clocksource/bcm2835_timer.c       | 38 ++++++++----
 drivers/clocksource/bcm_kona_timer.c      |  8 ++-
 drivers/clocksource/cadence_ttc_timer.c   | 74 +++++++++++++++---------
 drivers/clocksource/clksrc-dbx500-prcmu.c |  4 +-
 drivers/clocksource/clksrc-probe.c        | 14 ++++-
 drivers/clocksource/clksrc_st_lpc.c       | 20 ++++---
 drivers/clocksource/clps711x-timer.c      | 10 ++--
 drivers/clocksource/dw_apb_timer_of.c     |  4 +-
 drivers/clocksource/exynos_mct.c          | 32 +++++++----
 drivers/clocksource/fsl_ftm_timer.c       | 20 ++++---
 drivers/clocksource/h8300_timer16.c       | 12 ++--
 drivers/clocksource/h8300_timer8.c        | 11 ++--
 drivers/clocksource/h8300_tpu.c           | 10 ++--
 drivers/clocksource/meson6_timer.c        | 19 ++++--
 drivers/clocksource/mips-gic-timer.c      | 24 +++++---
 drivers/clocksource/moxart_timer.c        | 39 ++++++++-----
 drivers/clocksource/mps2-timer.c          |  8 ++-
 drivers/clocksource/mtk_timer.c           |  8 ++-
 drivers/clocksource/mxs_timer.c           | 24 +++++---
 drivers/clocksource/nomadik-mtu.c         | 43 +++++++++-----
 drivers/clocksource/pxa_timer.c           | 44 ++++++++++----
 drivers/clocksource/qcom-timer.c          | 23 ++++----
 drivers/clocksource/rockchip_timer.c      | 18 +++---
 drivers/clocksource/samsung_pwm_timer.c   | 54 +++++++++--------
 drivers/clocksource/sun4i_timer.c         | 43 ++++++++++----
 drivers/clocksource/tango_xtal.c          | 10 ++--
 drivers/clocksource/tegra20_timer.c       | 24 ++++----
 drivers/clocksource/time-armada-370-xp.c  | 96 +++++++++++++++++++++++--------
 drivers/clocksource/time-efm32.c          | 16 ++++--
 drivers/clocksource/time-lpc32xx.c        | 10 ++--
 drivers/clocksource/time-orion.c          | 50 +++++++++++-----
 drivers/clocksource/time-pistachio.c      | 18 +++---
 drivers/clocksource/timer-atlas7.c        | 30 ++++++----
 drivers/clocksource/timer-atmel-pit.c     | 41 ++++++++-----
 drivers/clocksource/timer-atmel-st.c      | 42 +++++++++-----
 drivers/clocksource/timer-digicolor.c     | 14 +++--
 drivers/clocksource/timer-imx-gpt.c       | 51 ++++++++++------
 drivers/clocksource/timer-integrator-ap.c | 57 +++++++++++-------
 drivers/clocksource/timer-keystone.c      | 13 +++--
 drivers/clocksource/timer-nps.c           | 14 +++--
 drivers/clocksource/timer-oxnas-rps.c     | 29 ++++++----
 drivers/clocksource/timer-prima2.c        | 41 +++++++++----
 drivers/clocksource/timer-sp804.c         | 87 ++++++++++++++++++----------
 drivers/clocksource/timer-stm32.c         |  8 ++-
 drivers/clocksource/timer-sun5i.c         | 33 +++++++----
 drivers/clocksource/timer-ti-32k.c        |  8 ++-
 drivers/clocksource/timer-u300.c          | 36 ++++++++----
 drivers/clocksource/versatile.c           |  6 +-
 drivers/clocksource/vf_pit_timer.c        | 25 +++++---
 drivers/clocksource/vt8500_timer.c        | 24 +++++---
 drivers/clocksource/zevio-timer.c         |  4 +-
 include/clocksource/timer-sp804.h         |  8 +--
 include/linux/clocksource.h               |  2 +-
 include/linux/of.h                        |  3 +
 63 files changed, 1133 insertions(+), 580 deletions(-)
Signature · 1 line
1.9.1
#1 lore raw

PATCH v2 1/63 of: Add a new macro to declare_of for one parameter function returning a value

The macro OF_DECLARE_1 expect a void (*func)(struct device_node *) while the OF_DECLARE_2 expect a int (*func)(struct device_node *, struct device_node *).

The second one allows to pass an init function returning a value, which make possible to call the functions in the table and check the return value in order to catch at a higher level the errors and handle them from there instead of doing a panic in each driver (well at least this is the case for the clkevt).

Unfortunately the OF_DECLARE_1 does not allow that and that lead to some code duplication and crappyness in the drivers.

The OF_DECLARE_1 is used by all the clk drivers and the clocksource/clockevent drivers. It is not possible to do the change in one shot as we have to change all the init functions.

The OF_DECLARE_2 specifies an init function prototype with two parameters with the node and its parent. The latter won't be used, ever, in the timer drivers.

Introduce a OF_DECLARE_1_RET macro to be used, and hopefully we can smoothly and iteratively change the users of OF_DECLARE_1 to use the new macro instead.

---
 include/linux/of.h | 3 +++
 1 file changed, 3 insertions(+)
include/linux/of.h +3 -0
index c7292e8..552943d 100644
@@ -1009,10 +1009,13 @@ static inline int of_get_available_child_count(const struct device_node *np)
 #endif
 
 typedef int (*of_init_fn_2)(struct device_node *, struct device_node *);
+typedef int (*of_init_fn_1_ret)(struct device_node *);
 typedef void (*of_init_fn_1)(struct device_node *);
 
 #define OF_DECLARE_1(table, name, compat, fn) \
 		_OF_DECLARE(table, name, compat, fn, of_init_fn_1)
+#define OF_DECLARE_1_RET(table, name, compat, fn) \
+		_OF_DECLARE(table, name, compat, fn, of_init_fn_1_ret)
 #define OF_DECLARE_2(table, name, compat, fn) \
 		_OF_DECLARE(table, name, compat, fn, of_init_fn_2)
 
Signature · 1 line
1.9.1
Acked-by on v2 1/63
#2 lore raw

Re: [PATCH V2 01/63] of: Add a new macro to declare_of for one parameter function returning a value

Quoted 18 lines · Daniel Lezcano

The macro OF_DECLARE_1 expect a void (*func)(struct device_node *) while the OF_DECLARE_2 expect a int (*func)(struct device_node *, struct device_node *).

The second one allows to pass an init function returning a value, which make possible to call the functions in the table and check the return value in order to catch at a higher level the errors and handle them from there instead of doing a panic in each driver (well at least this is the case for the clkevt).

Unfortunately the OF_DECLARE_1 does not allow that and that lead to some code duplication and crappyness in the drivers.

The OF_DECLARE_1 is used by all the clk drivers and the clocksource/clockevent drivers. It is not possible to do the change in one shot as we have to change all the init functions.

The OF_DECLARE_2 specifies an init function prototype with two parameters with the node and its parent. The latter won't be used, ever, in the timer drivers.

Quoted 7 lines

Introduce a OF_DECLARE_1_RET macro to be used, and hopefully we can smoothly and iteratively change the users of OF_DECLARE_1 to use the new macro instead.

---
 include/linux/of.h | 3 +++
 1 file changed, 3 insertions(+)

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html

#3 lore raw

PATCH v2 2/63 clocksource/drivers/clksrc-probe: Introduce init functions with return code

In reply to Daniel Lezcano

Currently, the clksrc-probe is not able to handle any error from the init functions. There are different issues with the current code:
- the code is duplicated in the init functions by writing error
- every driver tends to panic in its own init function
- counting the number of clocksources is not reliable

This patch adds another table to store the functions returning an error. The table is temporary while we convert all the drivers to return an error and will disappear.

---
 drivers/clocksource/clksrc-probe.c | 22 ++++++++++++++++++++++
 include/asm-generic/vmlinux.lds.h  |  2 ++
 include/linux/clocksource.h        |  3 +++
 3 files changed, 27 insertions(+)
drivers/clocksource/clksrc-probe.c +22 -0
index 7cb6c92..5fa6a55 100644
@@ -20,16 +20,22 @@
 #include <linux/clocksource.h>
 
 extern struct of_device_id __clksrc_of_table[];
+extern struct of_device_id __clksrc_ret_of_table[];
 
 static const struct of_device_id __clksrc_of_table_sentinel
 	__used __section(__clksrc_of_table_end);
 
+static const struct of_device_id __clksrc_ret_of_table_sentinel
+	__used __section(__clksrc_ret_of_table_end);
+
 void __init clocksource_probe(void)
 {
 	struct device_node *np;
 	const struct of_device_id *match;
 	of_init_fn_1 init_func;
+	of_init_fn_1_ret init_func_ret;
 	unsigned clocksources = 0;
+	int ret;
 
 	for_each_matching_node_and_match(np, __clksrc_of_table, &match) {
 		if (!of_device_is_available(np))
@@ -40,6 +46,22 @@ void __init clocksource_probe(void)
 		clocksources++;
 	}
 
+	for_each_matching_node_and_match(np, __clksrc_ret_of_table, &match) {
+		if (!of_device_is_available(np))
+			continue;
+
+		init_func_ret = match->data;
+
+		ret = init_func_ret(np);
+		if (ret) {
+			pr_err("Failed to initialize '%s': %d",
+			       of_node_full_name(np), ret);
+			continue;
+		}
+
+		clocksources++;
+	}
+
 	clocksources += acpi_probe_device_table(clksrc);
 
 	if (!clocksources)
include/asm-generic/vmlinux.lds.h +2 -0
index 6a67ab9..8c6c626 100644
@@ -173,6 +173,7 @@
 	*(__##name##_of_table_end)
 
 #define CLKSRC_OF_TABLES()	OF_TABLE(CONFIG_CLKSRC_OF, clksrc)
+#define CLKSRC_RET_OF_TABLES()	OF_TABLE(CONFIG_CLKSRC_OF, clksrc_ret)
 #define IRQCHIP_OF_MATCH_TABLE() OF_TABLE(CONFIG_IRQCHIP, irqchip)
 #define CLK_OF_TABLES()		OF_TABLE(CONFIG_COMMON_CLK, clk)
 #define IOMMU_OF_TABLES()	OF_TABLE(CONFIG_OF_IOMMU, iommu)
@@ -531,6 +532,7 @@
 	CLK_OF_TABLES()							\
 	RESERVEDMEM_OF_TABLES()						\
 	CLKSRC_OF_TABLES()						\
+	CLKSRC_RET_OF_TABLES()						\
 	IOMMU_OF_TABLES()						\
 	CPU_METHOD_OF_TABLES()						\
 	CPUIDLE_METHOD_OF_TABLES()					\
include/linux/clocksource.h +3 -0
index 44a1aff..15c3839 100644
@@ -246,6 +246,9 @@ extern int clocksource_i8253_init(void);
 #define CLOCKSOURCE_OF_DECLARE(name, compat, fn) \
 	OF_DECLARE_1(clksrc, name, compat, fn)
 
+#define CLOCKSOURCE_OF_DECLARE_RET(name, compat, fn) \
+	OF_DECLARE_1_RET(clksrc_ret, name, compat, fn)
+
 #ifdef CONFIG_CLKSRC_PROBE
 extern void clocksource_probe(void);
 #else
Signature · 1 line
1.9.1
#4 lore raw

PATCH v2 3/63 clocksource/drivers/rockchip_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/rockchip_timer.c | 26 ++++++++++++++------------
 1 file changed, 14 insertions(+), 12 deletions(-)
drivers/clocksource/rockchip_timer.c +14 -12
index a3f22b0..d10bdee 100644
@@ -113,17 +113,17 @@ static irqreturn_t rk_timer_interrupt(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
-static void __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
+static int __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
 {
 	struct clock_event_device *ce = &bc_timer.ce;
 	struct clk *timer_clk;
 	struct clk *pclk;
-	int ret, irq;
+	int ret = -EINVAL, irq;
 
 	bc_timer.base = of_iomap(np, 0);
 	if (!bc_timer.base) {
 		pr_err("Failed to get base address for '%s'\n", TIMER_NAME);
-		return;
+		return -ENXIO;
 	}
 	bc_timer.ctrl = bc_timer.base + ctrl_reg;
 
@@ -178,7 +178,7 @@ static void __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
 
 	clockevents_config_and_register(ce, bc_timer.freq, 1, UINT_MAX);
 
-	return;
+	return 0;
 
 out_irq:
 	clk_disable_unprepare(timer_clk);
@@ -186,19 +186,21 @@ out_timer_clk:
 	clk_disable_unprepare(pclk);
 out_unmap:
 	iounmap(bc_timer.base);
+
+	return ret;
 }
 
-static void __init rk3288_timer_init(struct device_node *np)
+static int __init rk3288_timer_init(struct device_node *np)
 {
-	rk_timer_init(np, TIMER_CONTROL_REG3288);
+	return rk_timer_init(np, TIMER_CONTROL_REG3288);
 }
 
-static void __init rk3399_timer_init(struct device_node *np)
+static int __init rk3399_timer_init(struct device_node *np)
 {
-	rk_timer_init(np, TIMER_CONTROL_REG3399);
+	return rk_timer_init(np, TIMER_CONTROL_REG3399);
 }
 
-CLOCKSOURCE_OF_DECLARE(rk3288_timer, "rockchip,rk3288-timer",
-		       rk3288_timer_init);
-CLOCKSOURCE_OF_DECLARE(rk3399_timer, "rockchip,rk3399-timer",
-		       rk3399_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(rk3288_timer, "rockchip,rk3288-timer",
+			   rk3288_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(rk3399_timer, "rockchip,rk3399-timer",
+			   rk3399_timer_init);
Signature · 1 line
1.9.1
maintainer
#5 lore raw

Re: [PATCH V2 03/63] clocksource/drivers/rockchip_timer: Convert init function to return error

Am Donnerstag, 16. Juni 2016, 23:26:22 schrieb Daniel Lezcano:

Quoted 35 lines

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/rockchip_timer.c | 26 ++++++++++++++------------
 1 file changed, 14 insertions(+), 12 deletions(-)
(quoted diff) +0 -0

b/drivers/clocksource/rockchip_timer.c index a3f22b0..d10bdee 100644

drivers/clocksource/rockchip_timer.c +1 -1
@@ -113,17 +113,17 @@ static irqreturn_t rk_timer_interrupt(int irq, void
 *dev_id) return IRQ_HANDLED;
 }
 
-static void __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
+static int __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
 {
 	struct clock_event_device *ce = &bc_timer.ce;
 	struct clk *timer_clk;
 	struct clk *pclk;

drivers/clocksource/rockchip_timer.c static irqreturn_t rk_timer_interrupt(int irq, void · line 128

Quoted 10 lines
drivers/clocksource/rockchip_timer.c +2 -2
-	int ret, irq;
+	int ret = -EINVAL, irq;
 
 	bc_timer.base = of_iomap(np, 0);
 	if (!bc_timer.base) {
 		pr_err("Failed to get base address for '%s'\n", TIMER_NAME);
-		return;
+		return -ENXIO;
 	}
 	bc_timer.ctrl = bc_timer.base + ctrl_reg;

wouldn't it be nicer to also save the error values from all the intermediate clock calls (ret = PTR_ERR(pclk) and so on).
Right now it will be always -EINVAL for all those clk calls and also the irq_of_parse_and_map.

Heiko

#6 lore raw

PATCH v3 1/1 clocksource/drivers/rockchip_timer: Convert init function to return error

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/rockchip_timer.c | 35 +++++++++++++++++++++--------------
 1 file changed, 21 insertions(+), 14 deletions(-)
drivers/clocksource/rockchip_timer.c +21 -14
index a3f22b0..85aee69 100644
@@ -113,38 +113,42 @@ static irqreturn_t rk_timer_interrupt(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
-static void __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
+static int __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
 {
 	struct clock_event_device *ce = &bc_timer.ce;
 	struct clk *timer_clk;
 	struct clk *pclk;
-	int ret, irq;
+	int ret = -EINVAL, irq;
 
 	bc_timer.base = of_iomap(np, 0);
 	if (!bc_timer.base) {
 		pr_err("Failed to get base address for '%s'\n", TIMER_NAME);
-		return;
+		return -ENXIO;
 	}
 	bc_timer.ctrl = bc_timer.base + ctrl_reg;
 
 	pclk = of_clk_get_by_name(np, "pclk");
 	if (IS_ERR(pclk)) {
+		ret = PTR_ERR(pclk);
 		pr_err("Failed to get pclk for '%s'\n", TIMER_NAME);
 		goto out_unmap;
 	}
 
-	if (clk_prepare_enable(pclk)) {
+	ret = clk_prepare_enable(pclk);
+	if (ret) {
 		pr_err("Failed to enable pclk for '%s'\n", TIMER_NAME);
 		goto out_unmap;
 	}
 
 	timer_clk = of_clk_get_by_name(np, "timer");
 	if (IS_ERR(timer_clk)) {
+		ret = PTR_ERR(timer_clk);
 		pr_err("Failed to get timer clock for '%s'\n", TIMER_NAME);
 		goto out_timer_clk;
 	}
 
-	if (clk_prepare_enable(timer_clk)) {
+	ret = clk_prepare_enable(timer_clk);
+	if (ret) {
 		pr_err("Failed to enable timer clock\n");
 		goto out_timer_clk;
 	}
@@ -153,6 +157,7 @@ static void __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
 
 	irq = irq_of_parse_and_map(np, 0);
 	if (!irq) {
+		ret = -EINVAL;
 		pr_err("Failed to map interrupts for '%s'\n", TIMER_NAME);
 		goto out_irq;
 	}
@@ -178,7 +183,7 @@ static void __init rk_timer_init(struct device_node *np, u32 ctrl_reg)
 
 	clockevents_config_and_register(ce, bc_timer.freq, 1, UINT_MAX);
 
-	return;
+	return 0;
 
 out_irq:
 	clk_disable_unprepare(timer_clk);
@@ -186,19 +191,21 @@ out_timer_clk:
 	clk_disable_unprepare(pclk);
 out_unmap:
 	iounmap(bc_timer.base);
+
+	return ret;
 }
 
-static void __init rk3288_timer_init(struct device_node *np)
+static int __init rk3288_timer_init(struct device_node *np)
 {
-	rk_timer_init(np, TIMER_CONTROL_REG3288);
+	return rk_timer_init(np, TIMER_CONTROL_REG3288);
 }
 
-static void __init rk3399_timer_init(struct device_node *np)
+static int __init rk3399_timer_init(struct device_node *np)
 {
-	rk_timer_init(np, TIMER_CONTROL_REG3399);
+	return rk_timer_init(np, TIMER_CONTROL_REG3399);
 }
 
-CLOCKSOURCE_OF_DECLARE(rk3288_timer, "rockchip,rk3288-timer",
-		       rk3288_timer_init);
-CLOCKSOURCE_OF_DECLARE(rk3399_timer, "rockchip,rk3399-timer",
-		       rk3399_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(rk3288_timer, "rockchip,rk3288-timer",
+			   rk3288_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(rk3399_timer, "rockchip,rk3399-timer",
+			   rk3399_timer_init);
Signature · 1 line
1.9.1
maintainer Reviewed-by Tested-by on v3 1/1
#7 lore raw

Re: [PATCH V3] clocksource/drivers/rockchip_timer: Convert init function to return error

Am Samstag, 18. Juni 2016, 14:54:07 schrieb Daniel Lezcano:

Quoted 9 lines

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Quoted 8 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

looks good now :-)

on a rk3399-evb

Heiko

#8 lore raw

PATCH v2 4/63 clocksource/drivers/mkt_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mtk_timer.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/clocksource/mtk_timer.c +6 -4
index 7e583f8..432a2c0 100644
@@ -181,7 +181,7 @@ static void mtk_timer_enable_irq(struct mtk_clock_event_device *evt, u8 timer)
 			evt->gpt_base + GPT_IRQ_EN_REG);
 }
 
-static void __init mtk_timer_init(struct device_node *node)
+static int __init mtk_timer_init(struct device_node *node)
 {
 	struct mtk_clock_event_device *evt;
 	struct resource res;
@@ -190,7 +190,7 @@ static void __init mtk_timer_init(struct device_node *node)
 
 	evt = kzalloc(sizeof(*evt), GFP_KERNEL);
 	if (!evt)
-		return;
+		return -ENOMEM;
 
 	evt->dev.name = "mtk_tick";
 	evt->dev.rating = 300;
@@ -248,7 +248,7 @@ static void __init mtk_timer_init(struct device_node *node)
 
 	mtk_timer_enable_irq(evt, GPT_CLK_EVT);
 
-	return;
+	return 0;
 
 err_clk_disable:
 	clk_disable_unprepare(clk);
@@ -262,5 +262,7 @@ err_mem:
 	release_mem_region(res.start, resource_size(&res));
 err_kzalloc:
 	kfree(evt);
+
+	return -EINVAL;
 }
-CLOCKSOURCE_OF_DECLARE(mtk_mt6577, "mediatek,mt6577-timer", mtk_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mtk_mt6577, "mediatek,mt6577-timer", mtk_timer_init);
Signature · 1 line
1.9.1
maintainer Acked-by on v2 4/63
#9 lore raw

Re: [PATCH V2 04/63] clocksource/drivers/mkt_timer: Convert init function to return error

Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 9 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
  drivers/clocksource/mtk_timer.c | 10 ++++++----
  1 file changed, 6 insertions(+), 4 deletions(-)
Quoted 41 lines
drivers/clocksource/mtk_timer.c +6 -4
index 7e583f8..432a2c0 100644
@@ -181,7 +181,7 @@ static void mtk_timer_enable_irq(struct mtk_clock_event_device *evt, u8 timer)
  			evt->gpt_base + GPT_IRQ_EN_REG);
  }
 
-static void __init mtk_timer_init(struct device_node *node)
+static int __init mtk_timer_init(struct device_node *node)
  {
  	struct mtk_clock_event_device *evt;
  	struct resource res;
@@ -190,7 +190,7 @@ static void __init mtk_timer_init(struct device_node *node)
 
  	evt = kzalloc(sizeof(*evt), GFP_KERNEL);
  	if (!evt)
-		return;
+		return -ENOMEM;
 
  	evt->dev.name = "mtk_tick";
  	evt->dev.rating = 300;
@@ -248,7 +248,7 @@ static void __init mtk_timer_init(struct device_node *node)
 
  	mtk_timer_enable_irq(evt, GPT_CLK_EVT);
 
-	return;
+	return 0;
 
  err_clk_disable:
  	clk_disable_unprepare(clk);
@@ -262,5 +262,7 @@ err_mem:
  	release_mem_region(res.start, resource_size(&res));
  err_kzalloc:
  	kfree(evt);
+
+	return -EINVAL;
  }
-CLOCKSOURCE_OF_DECLARE(mtk_mt6577, "mediatek,mt6577-timer", mtk_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mtk_mt6577, "mediatek,mt6577-timer", mtk_timer_init);
#10 lore raw

PATCH v2 5/63 clocksource/drivers/exynos_mct: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/exynos_mct.c | 36 ++++++++++++++++++++++++------------
 1 file changed, 24 insertions(+), 12 deletions(-)
drivers/clocksource/exynos_mct.c +24 -12
index be09bc0..f6caed0 100644
@@ -232,7 +232,7 @@ static cycles_t exynos4_read_current_timer(void)
 	return exynos4_read_count_32();
 }
 
-static void __init exynos4_clocksource_init(void)
+static int __init exynos4_clocksource_init(void)
 {
 	exynos4_mct_frc_start();
 
@@ -244,6 +244,8 @@ static void __init exynos4_clocksource_init(void)
 		panic("%s: can't register clocksource\n", mct_frc.name);
 
 	sched_clock_register(exynos4_read_sched_clock, 32, clk_rate);
+
+	return 0;
 }
 
 static void exynos4_mct_comp0_stop(void)
@@ -335,12 +337,14 @@ static struct irqaction mct_comp_event_irq = {
 	.dev_id		= &mct_comp_device,
 };
 
-static void exynos4_clockevent_init(void)
+static int exynos4_clockevent_init(void)
 {
 	mct_comp_device.cpumask = cpumask_of(0);
 	clockevents_config_and_register(&mct_comp_device, clk_rate,
 					0xf, 0xffffffff);
 	setup_irq(mct_irqs[MCT_G0_IRQ], &mct_comp_event_irq);
+
+	return 0;
 }
 
 static DEFINE_PER_CPU(struct mct_clock_event_device, percpu_mct_tick);
@@ -516,7 +520,7 @@ static struct notifier_block exynos4_mct_cpu_nb = {
 	.notifier_call = exynos4_mct_cpu_notify,
 };
 
-static void __init exynos4_timer_resources(struct device_node *np, void __iomem *base)
+static int __init exynos4_timer_resources(struct device_node *np, void __iomem *base)
 {
 	int err, cpu;
 	struct mct_clock_event_device *mevt = this_cpu_ptr(&percpu_mct_tick);
@@ -572,15 +576,17 @@ static void __init exynos4_timer_resources(struct device_node *np, void __iomem
 
 	/* Immediately configure the timer on the boot CPU */
 	exynos4_local_timer_setup(mevt);
-	return;
+	return 0;
 
 out_irq:
 	free_percpu_irq(mct_irqs[MCT_L0_IRQ], &percpu_mct_tick);
+	return err;
 }
 
-static void __init mct_init_dt(struct device_node *np, unsigned int int_type)
+static int __init mct_init_dt(struct device_node *np, unsigned int int_type)
 {
 	u32 nr_irqs, i;
+	int ret;
 
 	mct_int_type = int_type;
 
@@ -600,20 +606,26 @@ static void __init mct_init_dt(struct device_node *np, unsigned int int_type)
 	for (i = MCT_L0_IRQ; i < nr_irqs; i++)
 		mct_irqs[i] = irq_of_parse_and_map(np, i);
 
-	exynos4_timer_resources(np, of_iomap(np, 0));
-	exynos4_clocksource_init();
-	exynos4_clockevent_init();
+	ret = exynos4_timer_resources(np, of_iomap(np, 0));
+	if (ret)
+		return ret;
+
+	ret = exynos4_clocksource_init();
+	if (ret)
+		return ret;
+
+	return exynos4_clockevent_init();
 }
 
 
-static void __init mct_init_spi(struct device_node *np)
+static int __init mct_init_spi(struct device_node *np)
 {
 	return mct_init_dt(np, MCT_INT_SPI);
 }
 
-static void __init mct_init_ppi(struct device_node *np)
+static int __init mct_init_ppi(struct device_node *np)
 {
 	return mct_init_dt(np, MCT_INT_PPI);
 }
-CLOCKSOURCE_OF_DECLARE(exynos4210, "samsung,exynos4210-mct", mct_init_spi);
-CLOCKSOURCE_OF_DECLARE(exynos4412, "samsung,exynos4412-mct", mct_init_ppi);
+CLOCKSOURCE_OF_DECLARE_RET(exynos4210, "samsung,exynos4210-mct", mct_init_spi);
+CLOCKSOURCE_OF_DECLARE_RET(exynos4412, "samsung,exynos4412-mct", mct_init_ppi);
Signature · 1 line
1.9.1
#11 lore raw

PATCH v2 6/63 clocksource/drivers/asm9260: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/asm9260_timer.c | 24 ++++++++++++++++--------
 1 file changed, 16 insertions(+), 8 deletions(-)
drivers/clocksource/asm9260_timer.c +16 -8
index 217438d..d113c02 100644
@@ -184,7 +184,7 @@ static irqreturn_t asm9260_timer_interrupt(int irq, void *dev_id)
  * Timer initialization
  * ---------------------------------------------------------------------------
  */
-static void __init asm9260_timer_init(struct device_node *np)
+static int __init asm9260_timer_init(struct device_node *np)
 {
 	int irq;
 	struct clk *clk;
@@ -192,20 +192,26 @@ static void __init asm9260_timer_init(struct device_node *np)
 	unsigned long rate;
 
 	priv.base = of_io_request_and_map(np, 0, np->name);
-	if (IS_ERR(priv.base))
-		panic("%s: unable to map resource", np->name);
+	if (IS_ERR(priv.base)) {
+		pr_err("%s: unable to map resource", np->name);
+		return PTR_ERR(priv.base);
+	}
 
 	clk = of_clk_get(np, 0);
 
 	ret = clk_prepare_enable(clk);
-	if (ret)
-		panic("Failed to enable clk!\n");
+	if (ret) {
+		pr_err("Failed to enable clk!\n");
+		return ret;
+	}
 
 	irq = irq_of_parse_and_map(np, 0);
 	ret = request_irq(irq, asm9260_timer_interrupt, IRQF_TIMER,
 			DRIVER_NAME, &event_dev);
-	if (ret)
-		panic("Failed to setup irq!\n");
+	if (ret) {
+		pr_err("Failed to setup irq!\n");
+		return ret;
+	}
 
 	/* set all timers for count-up */
 	writel_relaxed(BM_DIR_DEFAULT, priv.base + HW_DIR);
@@ -229,6 +235,8 @@ static void __init asm9260_timer_init(struct device_node *np)
 	priv.ticks_per_jiffy = DIV_ROUND_CLOSEST(rate, HZ);
 	event_dev.cpumask = cpumask_of(0);
 	clockevents_config_and_register(&event_dev, rate, 0x2c00, 0xfffffffe);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(asm9260_timer, "alphascale,asm9260-timer",
+CLOCKSOURCE_OF_DECLARE_RET(asm9260_timer, "alphascale,asm9260-timer",
 		asm9260_timer_init);
Signature · 1 line
1.9.1
#12 lore raw

PATCH v2 7/63 clocksource/drivers/cadence_ttc: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/cadence_ttc_timer.c | 76 ++++++++++++++++++++-------------
 1 file changed, 47 insertions(+), 29 deletions(-)
drivers/clocksource/cadence_ttc_timer.c +47 -29
index 9be6018..e2e7631 100644
@@ -322,22 +322,22 @@ static int ttc_rate_change_clocksource_cb(struct notifier_block *nb,
 	return NOTIFY_DONE;
 }
 
-static void __init ttc_setup_clocksource(struct clk *clk, void __iomem *base,
+static int __init ttc_setup_clocksource(struct clk *clk, void __iomem *base,
 					 u32 timer_width)
 {
 	struct ttc_timer_clocksource *ttccs;
 	int err;
 
 	ttccs = kzalloc(sizeof(*ttccs), GFP_KERNEL);
-	if (WARN_ON(!ttccs))
-		return;
+	if (!ttccs)
+		return -ENOMEM;
 
 	ttccs->ttc.clk = clk;
 
 	err = clk_prepare_enable(ttccs->ttc.clk);
-	if (WARN_ON(err)) {
+	if (err) {
 		kfree(ttccs);
-		return;
+		return err;
 	}
 
 	ttccs->ttc.freq = clk_get_rate(ttccs->ttc.clk);
@@ -345,8 +345,10 @@ static void __init ttc_setup_clocksource(struct clk *clk, void __iomem *base,
 	ttccs->ttc.clk_rate_change_nb.notifier_call =
 		ttc_rate_change_clocksource_cb;
 	ttccs->ttc.clk_rate_change_nb.next = NULL;
-	if (clk_notifier_register(ttccs->ttc.clk,
-				&ttccs->ttc.clk_rate_change_nb))
+
+	err = clk_notifier_register(ttccs->ttc.clk,
+				    &ttccs->ttc.clk_rate_change_nb);
+	if (err)
 		pr_warn("Unable to register clock notifier.\n");
 
 	ttccs->ttc.base_addr = base;
@@ -368,14 +370,16 @@ static void __init ttc_setup_clocksource(struct clk *clk, void __iomem *base,
 		     ttccs->ttc.base_addr + TTC_CNT_CNTRL_OFFSET);
 
 	err = clocksource_register_hz(&ttccs->cs, ttccs->ttc.freq / PRESCALE);
-	if (WARN_ON(err)) {
+	if (err) {
 		kfree(ttccs);
-		return;
+		return err;
 	}
 
 	ttc_sched_clock_val_reg = base + TTC_COUNT_VAL_OFFSET;
 	sched_clock_register(ttc_sched_clock_read, timer_width,
 			     ttccs->ttc.freq / PRESCALE);
+
+	return 0;
 }
 
 static int ttc_rate_change_clockevent_cb(struct notifier_block *nb,
@@ -401,30 +405,35 @@ static int ttc_rate_change_clockevent_cb(struct notifier_block *nb,
 	}
 }
 
-static void __init ttc_setup_clockevent(struct clk *clk,
-						void __iomem *base, u32 irq)
+static int __init ttc_setup_clockevent(struct clk *clk,
+				       void __iomem *base, u32 irq)
 {
 	struct ttc_timer_clockevent *ttcce;
 	int err;
 
 	ttcce = kzalloc(sizeof(*ttcce), GFP_KERNEL);
-	if (WARN_ON(!ttcce))
-		return;
+	if (!ttcce)
+		return -ENOMEM;
 
 	ttcce->ttc.clk = clk;
 
 	err = clk_prepare_enable(ttcce->ttc.clk);
-	if (WARN_ON(err)) {
+	if (err) {
 		kfree(ttcce);
-		return;
+		return err;
 	}
 
 	ttcce->ttc.clk_rate_change_nb.notifier_call =
 		ttc_rate_change_clockevent_cb;
 	ttcce->ttc.clk_rate_change_nb.next = NULL;
-	if (clk_notifier_register(ttcce->ttc.clk,
-				&ttcce->ttc.clk_rate_change_nb))
+
+	err = clk_notifier_register(ttcce->ttc.clk,
+				    &ttcce->ttc.clk_rate_change_nb);
+	if (err) {
 		pr_warn("Unable to register clock notifier.\n");
+		return err;
+	}
+
 	ttcce->ttc.freq = clk_get_rate(ttcce->ttc.clk);
 
 	ttcce->ttc.base_addr = base;
@@ -451,13 +460,15 @@ static void __init ttc_setup_clockevent(struct clk *clk,
 
 	err = request_irq(irq, ttc_clock_event_interrupt,
 			  IRQF_TIMER, ttcce->ce.name, ttcce);
-	if (WARN_ON(err)) {
+	if (err) {
 		kfree(ttcce);
-		return;
+		return err;
 	}
 
 	clockevents_config_and_register(&ttcce->ce,
 			ttcce->ttc.freq / PRESCALE, 1, 0xfffe);
+
+	return 0;
 }
 
 /**
@@ -466,17 +477,17 @@ static void __init ttc_setup_clockevent(struct clk *clk,
  * Initializes the timer hardware and register the clock source and clock event
  * timers with Linux kernal timer framework
  */
-static void __init ttc_timer_init(struct device_node *timer)
+static int __init ttc_timer_init(struct device_node *timer)
 {
 	unsigned int irq;
 	void __iomem *timer_baseaddr;
 	struct clk *clk_cs, *clk_ce;
 	static int initialized;
-	int clksel;
+	int clksel, ret;
 	u32 timer_width = 16;
 
 	if (initialized)
-		return;
+		return 0;
 
 	initialized = 1;
 
@@ -488,13 +499,13 @@ static void __init ttc_timer_init(struct device_node *timer)
 	timer_baseaddr = of_iomap(timer, 0);
 	if (!timer_baseaddr) {
 		pr_err("ERROR: invalid timer base address\n");
-		BUG();
+		return -ENXIO;
 	}
 
 	irq = irq_of_parse_and_map(timer, 1);
 	if (irq <= 0) {
 		pr_err("ERROR: invalid interrupt number\n");
-		BUG();
+		return -EINVAL;
 	}
 
 	of_property_read_u32(timer, "timer-width", &timer_width);
@@ -504,7 +515,7 @@ static void __init ttc_timer_init(struct device_node *timer)
 	clk_cs = of_clk_get(timer, clksel);
 	if (IS_ERR(clk_cs)) {
 		pr_err("ERROR: timer input clock not found\n");
-		BUG();
+		return PTR_ERR(clk_cs);
 	}
 
 	clksel = readl_relaxed(timer_baseaddr + 4 + TTC_CLK_CNTRL_OFFSET);
@@ -512,13 +523,20 @@ static void __init ttc_timer_init(struct device_node *timer)
 	clk_ce = of_clk_get(timer, clksel);
 	if (IS_ERR(clk_ce)) {
 		pr_err("ERROR: timer input clock not found\n");
-		BUG();
+		return PTR_ERR(clk_cs);
 	}
 
-	ttc_setup_clocksource(clk_cs, timer_baseaddr, timer_width);
-	ttc_setup_clockevent(clk_ce, timer_baseaddr + 4, irq);
+	ret = ttc_setup_clocksource(clk_cs, timer_baseaddr, timer_width);
+	if (ret)
+		return ret;
+
+	ret = ttc_setup_clockevent(clk_ce, timer_baseaddr + 4, irq);
+	if (ret)
+		return ret;
 
 	pr_info("%s #0@%p, irq=%d\n", timer->name, timer_baseaddr, irq);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(ttc, "cdns,ttc", ttc_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(ttc, "cdns,ttc", ttc_timer_init);
Signature · 1 line
1.9.1
Acked-by on v2 7/63
#13 lore raw

Re: [PATCH V2 07/63] clocksource/drivers/cadence_ttc: Convert init function to return error

Quoted 9 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Quoted 8 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

S?ren

#14 lore raw

PATCH v2 8/63 clocksource/drivers/st_lpc: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/clksrc_st_lpc.c | 22 +++++++++++++---------
 1 file changed, 13 insertions(+), 9 deletions(-)
drivers/clocksource/clksrc_st_lpc.c +13 -9
index 65ec467..c9022a9 100644
@@ -92,7 +92,7 @@ static int __init st_clksrc_setup_clk(struct device_node *np)
 	return 0;
 }
 
-static void __init st_clksrc_of_register(struct device_node *np)
+static int __init st_clksrc_of_register(struct device_node *np)
 {
 	int ret;
 	uint32_t mode;
@@ -100,32 +100,36 @@ static void __init st_clksrc_of_register(struct device_node *np)
 	ret = of_property_read_u32(np, "st,lpc-mode", &mode);
 	if (ret) {
 		pr_err("clksrc-st-lpc: An LPC mode must be provided\n");
-		return;
+		return ret;
 	}
 
 	/* LPC can either run as a Clocksource or in RTC or WDT mode */
 	if (mode != ST_LPC_MODE_CLKSRC)
-		return;
+		return 0;
 
 	ddata.base = of_iomap(np, 0);
 	if (!ddata.base) {
 		pr_err("clksrc-st-lpc: Unable to map iomem\n");
-		return;
+		return -ENXIO;
 	}
 
-	if (st_clksrc_setup_clk(np)) {
+	ret = st_clksrc_setup_clk(np);
+	if (ret) {
 		iounmap(ddata.base);
-		return;
+		return ret;
 	}
 
-	if (st_clksrc_init()) {
+	ret = st_clksrc_init();
+	if (ret) {
 		clk_disable_unprepare(ddata.clk);
 		clk_put(ddata.clk);
 		iounmap(ddata.base);
-		return;
+		return ret;
 	}
 
 	pr_info("clksrc-st-lpc: clocksource initialised - running @ %luHz\n",
 		clk_get_rate(ddata.clk));
+
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(ddata, "st,stih407-lpc", st_clksrc_of_register);
+CLOCKSOURCE_OF_DECLARE_RET(ddata, "st,stih407-lpc", st_clksrc_of_register);
Signature · 1 line
1.9.1
Acked-by on v2 8/63
#15 lore raw

Re: [PATCH V2 08/63] clocksource/drivers/st_lpc: Convert init function to return error

Hi Daniel

Quoted 69 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
  drivers/clocksource/clksrc_st_lpc.c | 22 +++++++++++++---------
  1 file changed, 13 insertions(+), 9 deletions(-)
drivers/clocksource/clksrc_st_lpc.c +9 -8
index 65ec467..c9022a9 100644
@@ -92,7 +92,7 @@ static int __init st_clksrc_setup_clk(struct device_node *np)
  	return 0;
  }
 
-static void __init st_clksrc_of_register(struct device_node *np)
+static int __init st_clksrc_of_register(struct device_node *np)
  {
  	int ret;
  	uint32_t mode;
@@ -100,32 +100,36 @@ static void __init st_clksrc_of_register(struct device_node *np)
  	ret = of_property_read_u32(np, "st,lpc-mode", &mode);
  	if (ret) {
  		pr_err("clksrc-st-lpc: An LPC mode must be provided\n");
-		return;
+		return ret;
  	}
 
  	/* LPC can either run as a Clocksource or in RTC or WDT mode */
  	if (mode != ST_LPC_MODE_CLKSRC)
-		return;
+		return 0;
 
  	ddata.base = of_iomap(np, 0);
  	if (!ddata.base) {
  		pr_err("clksrc-st-lpc: Unable to map iomem\n");
-		return;
+		return -ENXIO;
  	}
 
-	if (st_clksrc_setup_clk(np)) {
+	ret = st_clksrc_setup_clk(np);
+	if (ret) {
  		iounmap(ddata.base);
-		return;
+		return ret;
  	}
 
-	if (st_clksrc_init()) {
+	ret = st_clksrc_init();
+	if (ret) {
  		clk_disable_unprepare(ddata.clk);
  		clk_put(ddata.clk);
  		iounmap(ddata.base);
-		return;

drivers/clocksource/clksrc_st_lpc.c static void __init st_clksrc_of_register(struct device_node *np) · line 135

Quoted 10 lines
drivers/clocksource/clksrc_st_lpc.c +4 -1
+		return ret;
  	}
 
  	pr_info("clksrc-st-lpc: clocksource initialised - running @ %luHz\n",
  		clk_get_rate(ddata.clk));
+
+	return ret;
  }
-CLOCKSOURCE_OF_DECLARE(ddata, "st,stih407-lpc", st_clksrc_of_register);
+CLOCKSOURCE_OF_DECLARE_RET(ddata, "st,stih407-lpc", st_clksrc_of_register);
Acked-by on v2 8/63
#16 lore raw

Re: [PATCH V2 08/63] clocksource/drivers/st_lpc: Convert init function to return error

In reply to Daniel Lezcano
Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 9 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
  drivers/clocksource/clksrc_st_lpc.c | 22 +++++++++++++---------
  1 file changed, 13 insertions(+), 9 deletions(-)

Thanks!
Maxime

#17 lore raw

PATCH v2 9/63 clocksource/drivers/dw_apb_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/dw_apb_timer_of.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/dw_apb_timer_of.c +7 -5
index 860843c..4985a2c 100644
@@ -143,7 +143,7 @@ static struct delay_timer dw_apb_delay_timer = {
 #endif
 
 static int num_called;
-static void __init dw_apb_timer_init(struct device_node *timer)
+static int __init dw_apb_timer_init(struct device_node *timer)
 {
 	switch (num_called) {
 	case 0:
@@ -164,8 +164,10 @@ static void __init dw_apb_timer_init(struct device_node *timer)
 	}
 
 	num_called++;
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(pc3x2_timer, "picochip,pc3x2-timer", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE(apb_timer_osc, "snps,dw-apb-timer-osc", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE(apb_timer_sp, "snps,dw-apb-timer-sp", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE(apb_timer, "snps,dw-apb-timer", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(pc3x2_timer, "picochip,pc3x2-timer", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(apb_timer_osc, "snps,dw-apb-timer-osc", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(apb_timer_sp, "snps,dw-apb-timer-sp", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(apb_timer, "snps,dw-apb-timer", dw_apb_timer_init);
Signature · 1 line
1.9.1
#18 lore raw

PATCH v2 10/63 clocksource/drivers/clps711x: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/clps711x-timer.c | 12 +++++-------
 1 file changed, 5 insertions(+), 7 deletions(-)
drivers/clocksource/clps711x-timer.c +5 -7
index cdd86e3..3b66198 100644
@@ -104,7 +104,7 @@ void __init clps711x_clksrc_init(void __iomem *tc1_base, void __iomem *tc2_base,
 }
 
 #ifdef CONFIG_CLKSRC_OF
-static void __init clps711x_timer_init(struct device_node *np)
+static int __init clps711x_timer_init(struct device_node *np)
 {
 	unsigned int irq = irq_of_parse_and_map(np, 0);
 	struct clk *clock = of_clk_get(np, 0);
@@ -112,14 +112,12 @@ static void __init clps711x_timer_init(struct device_node *np)
 
 	switch (of_alias_get_id(np, "timer")) {
 	case CLPS711X_CLKSRC_CLOCKSOURCE:
-		BUG_ON(_clps711x_clksrc_init(clock, base));
-		break;
+		return _clps711x_clksrc_init(clock, base);
 	case CLPS711X_CLKSRC_CLOCKEVENT:
-		BUG_ON(_clps711x_clkevt_init(clock, base, irq));
-		break;
+		return _clps711x_clkevt_init(clock, base, irq);
 	default:
-		break;
+		return -EINVAL;
 	}
 }
-CLOCKSOURCE_OF_DECLARE(clps711x, "cirrus,clps711x-timer", clps711x_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(clps711x, "cirrus,clps711x-timer", clps711x_timer_init);
 #endif
Signature · 1 line
1.9.1
#19 lore raw

PATCH v2 11/63 clocksource/drivers/digitcolor: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-digicolor.c | 16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)
drivers/clocksource/timer-digicolor.c +10 -6
index 96bb222..b929061 100644
@@ -148,7 +148,7 @@ static u64 notrace digicolor_timer_sched_read(void)
 	return ~readl(dc_timer_dev.base + COUNT(TIMER_B));
 }
 
-static void __init digicolor_timer_init(struct device_node *node)
+static int __init digicolor_timer_init(struct device_node *node)
 {
 	unsigned long rate;
 	struct clk *clk;
@@ -161,19 +161,19 @@ static void __init digicolor_timer_init(struct device_node *node)
 	dc_timer_dev.base = of_iomap(node, 0);
 	if (!dc_timer_dev.base) {
 		pr_err("Can't map registers");
-		return;
+		return -ENXIO;
 	}
 
 	irq = irq_of_parse_and_map(node, dc_timer_dev.timer_id);
 	if (irq <= 0) {
 		pr_err("Can't parse IRQ");
-		return;
+		return -EINVAL;
 	}
 
 	clk = of_clk_get(node, 0);
 	if (IS_ERR(clk)) {
 		pr_err("Can't get timer clock");
-		return;
+		return PTR_ERR(clk);
 	}
 	clk_prepare_enable(clk);
 	rate = clk_get_rate(clk);
@@ -190,13 +190,17 @@ static void __init digicolor_timer_init(struct device_node *node)
 	ret = request_irq(irq, digicolor_timer_interrupt,
 			  IRQF_TIMER | IRQF_IRQPOLL, "digicolor_timerC",
 			  &dc_timer_dev.ce);
-	if (ret)
+	if (ret) {
 		pr_warn("request of timer irq %d failed (%d)\n", irq, ret);
+		return ret;
+	}
 
 	dc_timer_dev.ce.cpumask = cpu_possible_mask;
 	dc_timer_dev.ce.irq = irq;
 
 	clockevents_config_and_register(&dc_timer_dev.ce, rate, 0, 0xffffffff);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(conexant_digicolor, "cnxt,cx92755-timer",
+CLOCKSOURCE_OF_DECLARE_RET(conexant_digicolor, "cnxt,cx92755-timer",
 		       digicolor_timer_init);
Signature · 1 line
1.9.1
maintainer Acked-by on v2 11/63
#20 lore raw

Re: [PATCH V2 11/63] clocksource/drivers/digitcolor: Convert init function to return error

Hi Daniel,

Quoted 9 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Quoted 8 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

It would be nice to have at least LAKL on Cc of the cover letter as well, so we can get the big picture. I found it at
http://article.gmane.org/gmane.linux.kernel/2246137.

But anyway, for this and the final patch:

Thanks,
baruch

Signature · 3 lines
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch at tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -
#21 lore raw

PATCH v2 12/63 clocksource/drivers/armv7m_systick: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/armv7m_systick.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)
drivers/clocksource/armv7m_systick.c +12 -6
index addfd2c..2b55410 100644
@@ -21,7 +21,7 @@
 
 #define SYSTICK_LOAD_RELOAD_MASK 0x00FFFFFF
 
-static void __init system_timer_of_register(struct device_node *np)
+static int __init system_timer_of_register(struct device_node *np)
 {
 	struct clk *clk = NULL;
 	void __iomem *base;
@@ -31,22 +31,26 @@ static void __init system_timer_of_register(struct device_node *np)
 	base = of_iomap(np, 0);
 	if (!base) {
 		pr_warn("system-timer: invalid base address\n");
-		return;
+		return -ENXIO;
 	}
 
 	ret = of_property_read_u32(np, "clock-frequency", &rate);
 	if (ret) {
 		clk = of_clk_get(np, 0);
-		if (IS_ERR(clk))
+		if (IS_ERR(clk)) {
+			ret = PTR_ERR(clk);
 			goto out_unmap;
+		}
 
 		ret = clk_prepare_enable(clk);
 		if (ret)
 			goto out_clk_put;
 
 		rate = clk_get_rate(clk);
-		if (!rate)
+		if (!rate) {
+			ret = -EINVAL;
 			goto out_clk_disable;
+		}
 	}
 
 	writel_relaxed(SYSTICK_LOAD_RELOAD_MASK, base + SYST_RVR);
@@ -64,7 +68,7 @@ static void __init system_timer_of_register(struct device_node *np)
 
 	pr_info("ARM System timer initialized as clocksource\n");
 
-	return;
+	return 0;
 
 out_clk_disable:
 	clk_disable_unprepare(clk);
@@ -73,7 +77,9 @@ out_clk_put:
 out_unmap:
 	iounmap(base);
 	pr_warn("ARM System timer register failed (%d)\n", ret);
+
+	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE(arm_systick, "arm,armv7m-systick",
+CLOCKSOURCE_OF_DECLARE_RET(arm_systick, "arm,armv7m-systick",
 			system_timer_of_register);
Signature · 1 line
1.9.1
maintainer Acked-by on v2 12/63
#22 lore raw

Re: [PATCH V2 12/63] clocksource/drivers/armv7m_systick: Convert init function to return error

2016-06-16 23:26 GMT+02:00 Daniel Lezcano <[email protected]>:

Quoted 12 lines

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 8 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/armv7m_systick.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

Thanks!
Maxime

#23 lore raw

PATCH v2 13/63 clocksource/drivers/bcm2835_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/bcm2835_timer.c | 40 +++++++++++++++++++++++++------------
 1 file changed, 27 insertions(+), 13 deletions(-)
drivers/clocksource/bcm2835_timer.c +27 -13
index 6f28229..2dcf896 100644
@@ -80,19 +80,24 @@ static irqreturn_t bcm2835_time_interrupt(int irq, void *dev_id)
 	}
 }
 
-static void __init bcm2835_timer_init(struct device_node *node)
+static int __init bcm2835_timer_init(struct device_node *node)
 {
 	void __iomem *base;
 	u32 freq;
-	int irq;
+	int irq, ret;
 	struct bcm2835_timer *timer;
 
 	base = of_iomap(node, 0);
-	if (!base)
-		panic("Can't remap registers");
+	if (!base) {
+		pr_err("Can't remap registers");
+		return -ENXIO;
+	}
 
-	if (of_property_read_u32(node, "clock-frequency", &freq))
-		panic("Can't read clock-frequency");
+	ret = of_property_read_u32(node, "clock-frequency", &freq);
+	if (ret) {
+		pr_err("Can't read clock-frequency");
+		return ret;
+	}
 
 	system_clock = base + REG_COUNTER_LO;
 	sched_clock_register(bcm2835_sched_read, 32, freq);
@@ -101,12 +106,16 @@ static void __init bcm2835_timer_init(struct device_node *node)
 		freq, 300, 32, clocksource_mmio_readl_up);
 
 	irq = irq_of_parse_and_map(node, DEFAULT_TIMER);
-	if (irq <= 0)
-		panic("Can't parse IRQ");
+	if (irq <= 0) {
+		pr_err("Can't parse IRQ");
+		return -EINVAL;
+	}
 
 	timer = kzalloc(sizeof(*timer), GFP_KERNEL);
-	if (!timer)
-		panic("Can't allocate timer struct\n");
+	if (!timer) {
+		pr_err("Can't allocate timer struct\n");
+		return -ENOMEM;
+	}
 
 	timer->control = base + REG_CONTROL;
 	timer->compare = base + REG_COMPARE(DEFAULT_TIMER);
@@ -121,12 +130,17 @@ static void __init bcm2835_timer_init(struct device_node *node)
 	timer->act.dev_id = timer;
 	timer->act.handler = bcm2835_time_interrupt;
 
-	if (setup_irq(irq, &timer->act))
-		panic("Can't set up timer IRQ\n");
+	ret = setup_irq(irq, &timer->act);
+	if (ret) {
+		pr_err("Can't set up timer IRQ\n");
+		return ret;
+	}
 
 	clockevents_config_and_register(&timer->evt, freq, 0xf, 0xffffffff);
 
 	pr_info("bcm2835: system timer (irq = %d)\n", irq);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(bcm2835, "brcm,bcm2835-system-timer",
+CLOCKSOURCE_OF_DECLARE_RET(bcm2835, "brcm,bcm2835-system-timer",
 			bcm2835_timer_init);
Signature · 1 line
1.9.1
Acked-by on v2 13/63
#24 lore raw

Re: [PATCH V2 13/63] clocksource/drivers/bcm2835_timer: Convert init function to return error

Quoted 9 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Quoted 8 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

For the bcm2835 changes here and in 63/63:

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 818 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160625/06972f9a/attachment.sig>

#25 lore raw

PATCH v2 14/63 clocksource/drivers/bcm_kona: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/bcm_kona_timer.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/bcm_kona_timer.c +7 -5
index e717e87..98bc2a2 100644
@@ -163,14 +163,14 @@ static struct irqaction kona_timer_irq = {
 	.handler = kona_timer_interrupt,
 };
 
-static void __init kona_timer_init(struct device_node *node)
+static int __init kona_timer_init(struct device_node *node)
 {
 	u32 freq;
 	struct clk *external_clk;
 
 	if (!of_device_is_available(node)) {
 		pr_info("Kona Timer v1 marked as disabled in device tree\n");
-		return;
+		return 0;
 	}
 
 	external_clk = of_clk_get_by_name(node, NULL);
@@ -182,7 +182,7 @@ static void __init kona_timer_init(struct device_node *node)
 		arch_timer_rate = freq;
 	} else {
 		pr_err("Kona Timer v1 unable to determine clock-frequency");
-		return;
+		return -EINVAL;
 	}
 
 	/* Setup IRQ numbers */
@@ -196,11 +196,13 @@ static void __init kona_timer_init(struct device_node *node)
 	kona_timer_clockevents_init();
 	setup_irq(timers.tmr_irq, &kona_timer_irq);
 	kona_timer_set_next_event((arch_timer_rate / HZ), NULL);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(brcm_kona, "brcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(brcm_kona, "brcm,kona-timer", kona_timer_init);
 /*
  * bcm,kona-timer is deprecated by brcm,kona-timer
  * being kept here for driver compatibility
  */
-CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(bcm_kona, "bcm,kona-timer", kona_timer_init);
Signature · 1 line
1.9.1
#26 lore raw

Re: [PATCH V2 14/63] clocksource/drivers/bcm_kona: Convert init function to return error

Hi Daniel,

Quoted 29 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/bcm_kona_timer.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/bcm_kona_timer.c +0 -0
index e717e87..98bc2a2 100644
@@ -163,14 +163,14 @@ static struct irqaction kona_timer_irq = {
 	.handler = kona_timer_interrupt,
 };
 

drivers/clocksource/bcm_kona_timer.c static struct irqaction kona_timer_irq = { · line 173

Quoted 10 lines
drivers/clocksource/bcm_kona_timer.c +2 -2
-static void __init kona_timer_init(struct device_node *node)
+static int __init kona_timer_init(struct device_node *node)
 {
 	u32 freq;
 	struct clk *external_clk;
 
 	if (!of_device_is_available(node)) {
 		pr_info("Kona Timer v1 marked as disabled in device tree\n");
-		return;
+		return 0;

I thought we should return -ENODEV here.

Moreover, if this device node is not enabled, kona_timer_init won't even be invoked. Can we simply get rid of this check here?

Quoted 19 lines
drivers/clocksource/bcm_kona_timer.c +3 -1
 	}
 
 	external_clk = of_clk_get_by_name(node, NULL);
@@ -182,7 +182,7 @@ static void __init kona_timer_init(struct device_node *node)
 		arch_timer_rate = freq;
 	} else {
 		pr_err("Kona Timer v1 unable to determine clock-frequency");
-		return;
+		return -EINVAL;
 	}
 
 	/* Setup IRQ numbers */
@@ -196,11 +196,13 @@ static void __init kona_timer_init(struct device_node *node)
 	kona_timer_clockevents_init();
 	setup_irq(timers.tmr_irq, &kona_timer_irq);
 	kona_timer_set_next_event((arch_timer_rate / HZ), NULL);
+
+	return 0;

drivers/clocksource/bcm_kona_timer.c static void __init kona_timer_init(struct device_node *node) · line 208

Quoted 10 lines
drivers/clocksource/bcm_kona_timer.c +2 -2
 }
 
-CLOCKSOURCE_OF_DECLARE(brcm_kona, "brcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(brcm_kona, "brcm,kona-timer", kona_timer_init);
 /*
  * bcm,kona-timer is deprecated by brcm,kona-timer
  * being kept here for driver compatibility
  */
-CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(bcm_kona, "bcm,kona-timer", kona_timer_init);

Thanks,

Ray

#27 lore raw

Re: [PATCH V2 14/63] clocksource/drivers/bcm_kona: Convert init function to return error

On 06/20/2016 07:22 PM, Ray Jui wrote:

[ ... ]

Quoted 13 lines

drivers/clocksource/bcm_kona_timer.c static struct irqaction kona_timer_irq = { · line 173

Quoted 10 lines
drivers/clocksource/bcm_kona_timer.c +2 -2
-static void __init kona_timer_init(struct device_node *node)
+static int __init kona_timer_init(struct device_node *node)
 {
     u32 freq;
     struct clk *external_clk;
 
     if (!of_device_is_available(node)) {
         pr_info("Kona Timer v1 marked as disabled in device tree\n");
-        return;
+        return 0;

I thought we should return -ENODEV here.

Quoted 2 lines

Moreover, if this device node is not enabled, kona_timer_init won't even be invoked. Can we simply get rid of this check here?

Yes, absolutely :)

Signature · 5 lines
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#28 lore raw

PATCH v3 1/1 clocksource/drivers/bcm_kona: Convert init function to return error

In reply to Ray Jui

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/bcm_kona_timer.c | 15 ++++++---------
 1 file changed, 6 insertions(+), 9 deletions(-)
drivers/clocksource/bcm_kona_timer.c +6 -9
index e717e87..c251aa6 100644
@@ -163,16 +163,11 @@ static struct irqaction kona_timer_irq = {
 	.handler = kona_timer_interrupt,
 };
 
-static void __init kona_timer_init(struct device_node *node)
+static int __init kona_timer_init(struct device_node *node)
 {
 	u32 freq;
 	struct clk *external_clk;
 
-	if (!of_device_is_available(node)) {
-		pr_info("Kona Timer v1 marked as disabled in device tree\n");
-		return;
-	}
-
 	external_clk = of_clk_get_by_name(node, NULL);
 
 	if (!IS_ERR(external_clk)) {
@@ -182,7 +177,7 @@ static void __init kona_timer_init(struct device_node *node)
 		arch_timer_rate = freq;
 	} else {
 		pr_err("Kona Timer v1 unable to determine clock-frequency");
-		return;
+		return -EINVAL;
 	}
 
 	/* Setup IRQ numbers */
@@ -196,11 +191,13 @@ static void __init kona_timer_init(struct device_node *node)
 	kona_timer_clockevents_init();
 	setup_irq(timers.tmr_irq, &kona_timer_irq);
 	kona_timer_set_next_event((arch_timer_rate / HZ), NULL);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(brcm_kona, "brcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(brcm_kona, "brcm,kona-timer", kona_timer_init);
 /*
  * bcm,kona-timer is deprecated by brcm,kona-timer
  * being kept here for driver compatibility
  */
-CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(bcm_kona, "bcm,kona-timer", kona_timer_init);
Signature · 1 line
1.9.1
Acked-by on v3 1/1
#29 lore raw

Re: [PATCH V3] clocksource/drivers/bcm_kona: Convert init function to return error

Hi Daniel,

Quoted 58 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/bcm_kona_timer.c | 15 ++++++---------
 1 file changed, 6 insertions(+), 9 deletions(-)
drivers/clocksource/bcm_kona_timer.c +4 -7
index e717e87..c251aa6 100644
@@ -163,16 +163,11 @@ static struct irqaction kona_timer_irq = {
 	.handler = kona_timer_interrupt,
 };
 
-static void __init kona_timer_init(struct device_node *node)
+static int __init kona_timer_init(struct device_node *node)
 {
 	u32 freq;
 	struct clk *external_clk;
 
-	if (!of_device_is_available(node)) {
-		pr_info("Kona Timer v1 marked as disabled in device tree\n");
-		return;
-	}
-
 	external_clk = of_clk_get_by_name(node, NULL);
 
 	if (!IS_ERR(external_clk)) {
@@ -182,7 +177,7 @@ static void __init kona_timer_init(struct device_node *node)
 		arch_timer_rate = freq;
 	} else {
 		pr_err("Kona Timer v1 unable to determine clock-frequency");
-		return;
+		return -EINVAL;
 	}
 
 	/* Setup IRQ numbers */
@@ -196,11 +191,13 @@ static void __init kona_timer_init(struct device_node *node)
 	kona_timer_clockevents_init();
 	setup_irq(timers.tmr_irq, &kona_timer_irq);
 	kona_timer_set_next_event((arch_timer_rate / HZ), NULL);
+
+	return 0;

drivers/clocksource/bcm_kona_timer.c static void __init kona_timer_init(struct device_node *node) · line 203

Quoted 10 lines
drivers/clocksource/bcm_kona_timer.c +2 -2
 }
 
-CLOCKSOURCE_OF_DECLARE(brcm_kona, "brcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(brcm_kona, "brcm,kona-timer", kona_timer_init);
 /*
  * bcm,kona-timer is deprecated by brcm,kona-timer
  * being kept here for driver compatibility
  */
-CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(bcm_kona, "bcm,kona-timer", kona_timer_init);

Looks good to me!

Thanks,

Ray

#30 lore raw

Re: [PATCH V3] clocksource/drivers/bcm_kona: Convert init function to return error

On 06/20/2016 07:50 PM, Ray Jui wrote:

[ ... ]

Quoted 6 lines

drivers/clocksource/bcm_kona_timer.c static void __init kona_timer_init(struct device_node *node) · line 203

Quoted 2 lines
drivers/clocksource/bcm_kona_timer.c +1 -1
-CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(bcm_kona, "bcm,kona-timer", kona_timer_init);

Looks good to me!

Can you have a quick look at the patch [63/63] for the kona part where CLOCKSOURCE_OF_DECLARE_RET is renamed back to CLOCKSOURCE_OF_DECLARE ?

Thanks !

-- Daniel

Signature · 5 lines
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#31 lore raw

PATCH v2 15/63 clocksource/drivers/clksrc-dbx500: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/clksrc-dbx500-prcmu.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/clocksource/clksrc-dbx500-prcmu.c +3 -3
index dfad6eb..5a59d29 100644
@@ -64,7 +64,7 @@ static u64 notrace dbx500_prcmu_sched_clock_read(void)
 
 #endif
 
-static void __init clksrc_dbx500_prcmu_init(struct device_node *node)
+static int __init clksrc_dbx500_prcmu_init(struct device_node *node)
 {
 	clksrc_dbx500_timer_base = of_iomap(node, 0);
 
@@ -84,7 +84,7 @@ static void __init clksrc_dbx500_prcmu_init(struct device_node *node)
 #ifdef CONFIG_CLKSRC_DBX500_PRCMU_SCHED_CLOCK
 	sched_clock_register(dbx500_prcmu_sched_clock_read, 32, RATE_32K);
 #endif
-	clocksource_register_hz(&clocksource_dbx500_prcmu, RATE_32K);
+	return clocksource_register_hz(&clocksource_dbx500_prcmu, RATE_32K);
 }
-CLOCKSOURCE_OF_DECLARE(dbx500_prcmu, "stericsson,db8500-prcmu-timer-4",
+CLOCKSOURCE_OF_DECLARE_RET(dbx500_prcmu, "stericsson,db8500-prcmu-timer-4",
 		       clksrc_dbx500_prcmu_init);
Signature · 1 line
1.9.1
Acked-by on v2 15/63
#32 lore raw

Re: [PATCH V2 15/63] clocksource/drivers/clksrc-dbx500: Convert init function to return error

Quoted 9 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Quoted 8 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Yours,
Linus Walleij

#33 lore raw

PATCH v2 16/63 clocksource/drivers/fsl_ftm_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/fsl_ftm_timer.c | 22 ++++++++++++++--------
 1 file changed, 14 insertions(+), 8 deletions(-)
drivers/clocksource/fsl_ftm_timer.c +14 -8
index 517e1c7..9ad4ca3 100644
@@ -316,15 +316,16 @@ static int __init ftm_calc_closest_round_cyc(unsigned long freq)
 	return 0;
 }
 
-static void __init ftm_timer_init(struct device_node *np)
+static int __init ftm_timer_init(struct device_node *np)
 {
 	unsigned long freq;
-	int irq;
+	int ret, irq;
 
 	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
 	if (!priv)
-		return;
+		return -ENOMEM;
 
+	ret = -ENXIO;
 	priv->clkevt_base = of_iomap(np, 0);
 	if (!priv->clkevt_base) {
 		pr_err("ftm: unable to map event timer registers\n");
@@ -337,6 +338,7 @@ static void __init ftm_timer_init(struct device_node *np)
 		goto err;
 	}
 
+	ret = -EINVAL;
 	irq = irq_of_parse_and_map(np, 0);
 	if (irq <= 0) {
 		pr_err("ftm: unable to get IRQ from DT, %d\n", irq);
@@ -349,18 +351,22 @@ static void __init ftm_timer_init(struct device_node *np)
 	if (!freq)
 		goto err;
 
-	if (ftm_calc_closest_round_cyc(freq))
+	ret = ftm_calc_closest_round_cyc(freq);
+	if (ret)
 		goto err;
 
-	if (ftm_clocksource_init(freq))
+	ret = ftm_clocksource_init(freq);
+	if (ret)
 		goto err;
 
-	if (ftm_clockevent_init(freq, irq))
+	ret = ftm_clockevent_init(freq, irq);
+	if (ret)
 		goto err;
 
-	return;
+	return 0;
 
 err:
 	kfree(priv);
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(flextimer, "fsl,ftm-timer", ftm_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(flextimer, "fsl,ftm-timer", ftm_timer_init);
Signature · 1 line
1.9.1
#34 lore raw

PATCH v2 17/63 clocksource/drivers/arm_arch_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/arm_arch_timer.c | 52 +++++++++++++++++++++++-------------
 1 file changed, 33 insertions(+), 19 deletions(-)
drivers/clocksource/arm_arch_timer.c +33 -19
index 4814446..d0cda68 100644
@@ -693,25 +693,26 @@ arch_timer_needs_probing(int type, const struct of_device_id *matches)
 	return needs_probing;
 }
 
-static void __init arch_timer_common_init(void)
+static int __init arch_timer_common_init(void)
 {
 	unsigned mask = ARCH_CP15_TIMER | ARCH_MEM_TIMER;
 
 	/* Wait until both nodes are probed if we have two timers */
 	if ((arch_timers_present & mask) != mask) {
 		if (arch_timer_needs_probing(ARCH_MEM_TIMER, arch_timer_mem_of_match))
-			return;
+			return 0;
 		if (arch_timer_needs_probing(ARCH_CP15_TIMER, arch_timer_of_match))
-			return;
+			return 0;
 	}
 
 	arch_timer_banner(arch_timers_present);
 	arch_counter_register(arch_timers_present);
-	arch_timer_arch_init();
+	return arch_timer_arch_init();
 }
 
-static void __init arch_timer_init(void)
+static int __init arch_timer_init(void)
 {
+	int ret;
 	/*
 	 * If HYP mode is available, we know that the physical timer
 	 * has been configured to be accessible from PL1. Use it, so
@@ -739,23 +740,30 @@ static void __init arch_timer_init(void)
 
 		if (!has_ppi) {
 			pr_warn("arch_timer: No interrupt available, giving up\n");
-			return;
+			return -EINVAL;
 		}
 	}
 
-	arch_timer_register();
-	arch_timer_common_init();
+	ret = arch_timer_register();
+	if (ret)
+		return ret;
+
+	ret = arch_timer_common_init();
+	if (ret)
+		return ret;
 
 	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[VIRT_PPI];
+	
+	return 0;
 }
 
-static void __init arch_timer_of_init(struct device_node *np)
+static int __init arch_timer_of_init(struct device_node *np)
 {
 	int i;
 
 	if (arch_timers_present & ARCH_CP15_TIMER) {
 		pr_warn("arch_timer: multiple nodes in dt, skipping\n");
-		return;
+		return 0;
 	}
 
 	arch_timers_present |= ARCH_CP15_TIMER;
@@ -774,23 +782,23 @@ static void __init arch_timer_of_init(struct device_node *np)
 	    of_property_read_bool(np, "arm,cpu-registers-not-fw-configured"))
 		arch_timer_uses_ppi = PHYS_SECURE_PPI;
 
-	arch_timer_init();
+	return arch_timer_init();
 }
-CLOCKSOURCE_OF_DECLARE(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
-CLOCKSOURCE_OF_DECLARE(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
+CLOCKSOURCE_OF_DECLARE_RET(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
+CLOCKSOURCE_OF_DECLARE_RET(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
 
-static void __init arch_timer_mem_init(struct device_node *np)
+static int __init arch_timer_mem_init(struct device_node *np)
 {
 	struct device_node *frame, *best_frame = NULL;
 	void __iomem *cntctlbase, *base;
-	unsigned int irq;
+	unsigned int irq, ret = -EINVAL;
 	u32 cnttidr;
 
 	arch_timers_present |= ARCH_MEM_TIMER;
 	cntctlbase = of_iomap(np, 0);
 	if (!cntctlbase) {
 		pr_err("arch_timer: Can't find CNTCTLBase\n");
-		return;
+		return -ENXIO;
 	}
 
 	cnttidr = readl_relaxed(cntctlbase + CNTTIDR);
@@ -830,6 +838,7 @@ static void __init arch_timer_mem_init(struct device_node *np)
 		best_frame = of_node_get(frame);
 	}
 
+	ret= -ENXIO;
 	base = arch_counter_base = of_iomap(best_frame, 0);
 	if (!base) {
 		pr_err("arch_timer: Can't map frame's registers\n");
@@ -841,6 +850,7 @@ static void __init arch_timer_mem_init(struct device_node *np)
 	else
 		irq = irq_of_parse_and_map(best_frame, 0);
 
+	ret = -EINVAL;
 	if (!irq) {
 		pr_err("arch_timer: Frame missing %s irq",
 		       arch_timer_mem_use_virtual ? "virt" : "phys");
@@ -848,13 +858,17 @@ static void __init arch_timer_mem_init(struct device_node *np)
 	}
 
 	arch_timer_detect_rate(base, np);
-	arch_timer_mem_register(base, irq);
-	arch_timer_common_init();
+	ret = arch_timer_mem_register(base, irq);
+	if (ret)
+		goto out;
+
+	return arch_timer_common_init();
 out:
 	iounmap(cntctlbase);
 	of_node_put(best_frame);
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
+CLOCKSOURCE_OF_DECLARE_RET(armv7_arch_timer_mem, "arm,armv7-timer-mem",
 		       arch_timer_mem_init);
 
 #ifdef CONFIG_ACPI
Signature · 1 line
1.9.1
#35 lore raw

PATCH v2 18/63 clocksource/drivers/arm_global_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/arm_global_timer.c | 28 ++++++++++++++++++----------
 1 file changed, 18 insertions(+), 10 deletions(-)
drivers/clocksource/arm_global_timer.c +18 -10
index 9df0d16..40104fc 100644
@@ -238,7 +238,7 @@ static void __init gt_delay_timer_init(void)
 	register_current_timer_delay(&gt_delay_timer);
 }
 
-static void __init gt_clocksource_init(void)
+static int __init gt_clocksource_init(void)
 {
 	writel(0, gt_base + GT_CONTROL);
 	writel(0, gt_base + GT_COUNTER0);
@@ -249,7 +249,7 @@ static void __init gt_clocksource_init(void)
 #ifdef CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK
 	sched_clock_register(gt_sched_clock_read, 64, gt_clk_rate);
 #endif
-	clocksource_register_hz(&gt_clocksource, gt_clk_rate);
+	return clocksource_register_hz(&gt_clocksource, gt_clk_rate);
 }
 
 static int gt_cpu_notify(struct notifier_block *self, unsigned long action,
@@ -270,7 +270,7 @@ static struct notifier_block gt_cpu_nb = {
 	.notifier_call = gt_cpu_notify,
 };
 
-static void __init global_timer_of_register(struct device_node *np)
+static int __init global_timer_of_register(struct device_node *np)
 {
 	struct clk *gt_clk;
 	int err = 0;
@@ -283,19 +283,19 @@ static void __init global_timer_of_register(struct device_node *np)
 	if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9
 	    && (read_cpuid_id() & 0xf0000f) < 0x200000) {
 		pr_warn("global-timer: non support for this cpu version.\n");
-		return;
+		return -ENOSYS;
 	}
 
 	gt_ppi = irq_of_parse_and_map(np, 0);
 	if (!gt_ppi) {
 		pr_warn("global-timer: unable to parse irq\n");
-		return;
+		return -EINVAL;
 	}
 
 	gt_base = of_iomap(np, 0);
 	if (!gt_base) {
 		pr_warn("global-timer: invalid base address\n");
-		return;
+		return -ENXIO;
 	}
 
 	gt_clk = of_clk_get(np, 0);
@@ -332,11 +332,17 @@ static void __init global_timer_of_register(struct device_node *np)
 	}
 
 	/* Immediately configure the timer on the boot CPU */
-	gt_clocksource_init();
-	gt_clockevents_init(this_cpu_ptr(gt_evt));
+	err = gt_clocksource_init();
+	if (err)
+		goto out_irq;
+	
+	err = gt_clockevents_init(this_cpu_ptr(gt_evt));
+	if (err)
+		goto out_irq;
+
 	gt_delay_timer_init();
 
-	return;
+	return 0;
 
 out_irq:
 	free_percpu_irq(gt_ppi, gt_evt);
@@ -347,8 +353,10 @@ out_clk:
 out_unmap:
 	iounmap(gt_base);
 	WARN(err, "ARM Global timer register failed (%d)\n", err);
+
+	return err;
 }
 
 /* Only tested on r2p2 and r3p0  */
-CLOCKSOURCE_OF_DECLARE(arm_gt, "arm,cortex-a9-global-timer",
+CLOCKSOURCE_OF_DECLARE_RET(arm_gt, "arm,cortex-a9-global-timer",
 			global_timer_of_register);
Signature · 1 line
1.9.1
Acked-by on v2 18/63
#36 lore raw

Re: [PATCH V2 18/63] clocksource/drivers/arm_global_timer: Convert init function to return error

Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 10 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
  drivers/clocksource/arm_global_timer.c | 28 ++++++++++++++++++----------
  1 file changed, 18 insertions(+), 10 deletions(-)

Thanks!
Maxime

#37 lore raw

PATCH v2 19/63 clocksource/drivers/h8300_timer16: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/h8300_timer16.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
drivers/clocksource/h8300_timer16.c +8 -4
index 75c4407..9d99fc8 100644
@@ -126,7 +126,7 @@ static struct timer16_priv timer16_priv = {
 #define REG_CH   0
 #define REG_COMM 1
 
-static void __init h8300_16timer_init(struct device_node *node)
+static int __init h8300_16timer_init(struct device_node *node)
 {
 	void __iomem *base[2];
 	int ret, irq;
@@ -136,9 +136,10 @@ static void __init h8300_16timer_init(struct device_node *node)
 	clk = of_clk_get(node, 0);
 	if (IS_ERR(clk)) {
 		pr_err("failed to get clock for clocksource\n");
-		return;
+		return PTR_ERR(clk);
 	}
 
+	ret = -ENXIO;
 	base[REG_CH] = of_iomap(node, 0);
 	if (!base[REG_CH]) {
 		pr_err("failed to map registers for clocksource\n");
@@ -151,6 +152,7 @@ static void __init h8300_16timer_init(struct device_node *node)
 		goto unmap_ch;
 	}
 
+	ret = -EINVAL;
 	irq = irq_of_parse_and_map(node, 0);
 	if (!irq) {
 		pr_err("failed to get irq for clockevent\n");
@@ -174,7 +176,7 @@ static void __init h8300_16timer_init(struct device_node *node)
 
 	clocksource_register_hz(&timer16_priv.cs,
 				clk_get_rate(clk) / 8);
-	return;
+	return 0;
 
 unmap_comm:
 	iounmap(base[REG_COMM]);
@@ -182,6 +184,8 @@ unmap_ch:
 	iounmap(base[REG_CH]);
 free_clk:
 	clk_put(clk);
+	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE(h8300_16bit, "renesas,16bit-timer", h8300_16timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(h8300_16bit, "renesas,16bit-timer",
+			   h8300_16timer_init);
Signature · 1 line
1.9.1
#38 lore raw

PATCH v2 20/63 clocksource/drivers/h8300_tpu: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/h8300_timer8.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)
drivers/clocksource/h8300_timer8.c +8 -5
index c151941..0292a19 100644
@@ -164,24 +164,26 @@ static struct timer8_priv timer8_priv = {
 	},
 };
 
-static void __init h8300_8timer_init(struct device_node *node)
+static int __init h8300_8timer_init(struct device_node *node)
 {
 	void __iomem *base;
-	int irq;
+	int irq, ret;
 	struct clk *clk;
 
 	clk = of_clk_get(node, 0);
 	if (IS_ERR(clk)) {
 		pr_err("failed to get clock for clockevent\n");
-		return;
+		return PTR_ERR(clk);
 	}
 
+	ret = ENXIO;
 	base = of_iomap(node, 0);
 	if (!base) {
 		pr_err("failed to map registers for clockevent\n");
 		goto free_clk;
 	}
 
+	ret = -EINVAL;
 	irq = irq_of_parse_and_map(node, 0);
 	if (!irq) {
 		pr_err("failed to get irq for clockevent\n");
@@ -205,11 +207,12 @@ static void __init h8300_8timer_init(struct device_node *node)
 	clockevents_config_and_register(&timer8_priv.ced,
 					timer8_priv.rate, 1, 0x0000ffff);
 
-	return;
+	return 0;
 unmap_reg:
 	iounmap(base);
 free_clk:
 	clk_put(clk);
+	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE(h8300_8bit, "renesas,8bit-timer", h8300_8timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(h8300_8bit, "renesas,8bit-timer", h8300_8timer_init);
Signature · 1 line
1.9.1
#39 lore raw

PATCH v2 21/63 clocksource/drivers/h8300_tpu: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/h8300_tpu.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/clocksource/h8300_tpu.c +6 -6
index d4c1a28..4faf718 100644
@@ -119,15 +119,16 @@ static struct tpu_priv tpu_priv = {
 #define CH_L 0
 #define CH_H 1
 
-static void __init h8300_tpu_init(struct device_node *node)
+static int __init h8300_tpu_init(struct device_node *node)
 {
 	void __iomem *base[2];
 	struct clk *clk;
+	int ret = -ENXIO;
 
 	clk = of_clk_get(node, 0);
 	if (IS_ERR(clk)) {
 		pr_err("failed to get clock for clocksource\n");
-		return;
+		return PTR_ERR(clk);
 	}
 
 	base[CH_L] = of_iomap(node, CH_L);
@@ -144,14 +145,13 @@ static void __init h8300_tpu_init(struct device_node *node)
 	tpu_priv.mapbase1 = base[CH_L];
 	tpu_priv.mapbase2 = base[CH_H];
 
-	clocksource_register_hz(&tpu_priv.cs, clk_get_rate(clk) / 64);
-
-	return;
+	return clocksource_register_hz(&tpu_priv.cs, clk_get_rate(clk) / 64);
 
 unmap_L:
 	iounmap(base[CH_H]);
 free_clk:
 	clk_put(clk);
+	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE(h8300_tpu, "renesas,tpu", h8300_tpu_init);
+CLOCKSOURCE_OF_DECLARE_RET(h8300_tpu, "renesas,tpu", h8300_tpu_init);
Signature · 1 line
1.9.1
#40 lore raw

PATCH v2 22/63 clocksource/drivers/mips-gic-timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/meson6_timer.c | 21 ++++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)
drivers/clocksource/meson6_timer.c +14 -7
index 1fa22c4..3a6e78f 100644
@@ -126,18 +126,22 @@ static struct irqaction meson6_timer_irq = {
 	.dev_id		= &meson6_clockevent,
 };
 
-static void __init meson6_timer_init(struct device_node *node)
+static int __init meson6_timer_init(struct device_node *node)
 {
 	u32 val;
 	int ret, irq;
 
 	timer_base = of_io_request_and_map(node, 0, "meson6-timer");
-	if (IS_ERR(timer_base))
-		panic("Can't map registers");
+	if (IS_ERR(timer_base)) {
+		pr_err("Can't map registers");
+		return -ENXIO;
+	}
 
 	irq = irq_of_parse_and_map(node, 0);
-	if (irq <= 0)
-		panic("Can't parse IRQ");
+	if (irq <= 0) {
+		pr_err("Can't parse IRQ");
+		return -EINVAL;
+	}
 
 	/* Set 1us for timer E */
 	val = readl(timer_base + TIMER_ISA_MUX);
@@ -158,14 +162,17 @@ static void __init meson6_timer_init(struct device_node *node)
 	meson6_clkevt_time_stop(CED_ID);
 
 	ret = setup_irq(irq, &meson6_timer_irq);
-	if (ret)
+	if (ret) {
 		pr_warn("failed to setup irq %d\n", irq);
+		return ret;
+	}
 
 	meson6_clockevent.cpumask = cpu_possible_mask;
 	meson6_clockevent.irq = irq;
 
 	clockevents_config_and_register(&meson6_clockevent, USEC_PER_SEC,
 					1, 0xfffe);
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(meson6, "amlogic,meson6-timer",
+CLOCKSOURCE_OF_DECLARE_RET(meson6, "amlogic,meson6-timer",
 		       meson6_timer_init);
Signature · 1 line
1.9.1
#41 lore raw

PATCH v2 23/63 clocksource/drivers/moxart_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mips-gic-timer.c | 26 +++++++++++++++++---------
 1 file changed, 17 insertions(+), 9 deletions(-)
drivers/clocksource/mips-gic-timer.c +17 -9
index 89d3e4d..b164b87 100644
@@ -146,7 +146,7 @@ static struct clocksource gic_clocksource = {
 	.archdata	= { .vdso_clock_mode = VDSO_CLOCK_GIC },
 };
 
-static void __init __gic_clocksource_init(void)
+static int __init __gic_clocksource_init(void)
 {
 	int ret;
 
@@ -159,6 +159,8 @@ static void __init __gic_clocksource_init(void)
 	ret = clocksource_register_hz(&gic_clocksource, gic_frequency);
 	if (ret < 0)
 		pr_warn("GIC: Unable to register clocksource\n");
+
+	return ret;
 }
 
 void __init gic_clocksource_init(unsigned int frequency)
@@ -179,31 +181,35 @@ static void __init gic_clocksource_of_init(struct device_node *node)
 	struct clk *clk;
 	int ret;
 
-	if (WARN_ON(!gic_present || !node->parent ||
-		    !of_device_is_compatible(node->parent, "mti,gic")))
-		return;
+	if (!gic_present || !node->parent ||
+	    !of_device_is_compatible(node->parent, "mti,gic")) {
+		pr_warn("No DT definition for the mips gic driver");
+		return -ENXIO;
+	}
 
 	clk = of_clk_get(node, 0);
 	if (!IS_ERR(clk)) {
 		if (clk_prepare_enable(clk) < 0) {
 			pr_err("GIC failed to enable clock\n");
 			clk_put(clk);
-			return;
+			return PTR_ERR(clk);
 		}
 
 		gic_frequency = clk_get_rate(clk);
 	} else if (of_property_read_u32(node, "clock-frequency",
 					&gic_frequency)) {
 		pr_err("GIC frequency not specified.\n");
-		return;
+		return -EINVAL;;
 	}
 	gic_timer_irq = irq_of_parse_and_map(node, 0);
 	if (!gic_timer_irq) {
 		pr_err("GIC timer IRQ not specified.\n");
-		return;
+		return -EINVAL;;
 	}
 
-	__gic_clocksource_init();
+	ret = __gic_clocksource_init();
+	if (ret)
+		return ret;
 
 	ret = gic_clockevent_init();
 	if (!ret && !IS_ERR(clk)) {
@@ -213,6 +219,8 @@ static void __init gic_clocksource_of_init(struct device_node *node)
 
 	/* And finally start the counter */
 	gic_start_count();
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(mips_gic_timer, "mti,gic-timer",
+CLOCKSOURCE_OF_DECLARE_RET(mips_gic_timer, "mti,gic-timer",
 		       gic_clocksource_of_init);
Signature · 1 line
1.9.1
#42 lore raw

PATCH v2 24/63 clocksource/drivers/mps2-timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/moxart_timer.c | 41 +++++++++++++++++++++++++-------------
 1 file changed, 27 insertions(+), 14 deletions(-)
drivers/clocksource/moxart_timer.c +27 -14
index 19857af..b9c30cd 100644
@@ -119,34 +119,45 @@ static struct irqaction moxart_timer_irq = {
 	.dev_id		= &moxart_clockevent,
 };
 
-static void __init moxart_timer_init(struct device_node *node)
+static int __init moxart_timer_init(struct device_node *node)
 {
 	int ret, irq;
 	unsigned long pclk;
 	struct clk *clk;
 
 	base = of_iomap(node, 0);
-	if (!base)
-		panic("%s: of_iomap failed\n", node->full_name);
+	if (!base) {
+		pr_err("%s: of_iomap failed\n", node->full_name);
+		return -ENXIO;
+	}
 
 	irq = irq_of_parse_and_map(node, 0);
-	if (irq <= 0)
-		panic("%s: irq_of_parse_and_map failed\n", node->full_name);
+	if (irq <= 0) {
+		pr_err("%s: irq_of_parse_and_map failed\n", node->full_name);
+		return -EINVAL;
+	}
 
 	ret = setup_irq(irq, &moxart_timer_irq);
-	if (ret)
-		panic("%s: setup_irq failed\n", node->full_name);
+	if (ret) {
+		pr_err("%s: setup_irq failed\n", node->full_name);
+		return ret;
+	}
 
 	clk = of_clk_get(node, 0);
-	if (IS_ERR(clk))
-		panic("%s: of_clk_get failed\n", node->full_name);
+	if (IS_ERR(clk))  {
+		pr_err("%s: of_clk_get failed\n", node->full_name);
+		return PTR_ERR(clk);
+	}
 
 	pclk = clk_get_rate(clk);
 
-	if (clocksource_mmio_init(base + TIMER2_BASE + REG_COUNT,
-				  "moxart_timer", pclk, 200, 32,
-				  clocksource_mmio_readl_down))
-		panic("%s: clocksource_mmio_init failed\n", node->full_name);
+	ret = clocksource_mmio_init(base + TIMER2_BASE + REG_COUNT,
+				    "moxart_timer", pclk, 200, 32,
+				    clocksource_mmio_readl_down);
+	if (ret) {
+		pr_err("%s: clocksource_mmio_init failed\n", node->full_name);
+		return ret;
+	}
 
 	clock_count_per_tick = DIV_ROUND_CLOSEST(pclk, HZ);
 
@@ -164,5 +175,7 @@ static void __init moxart_timer_init(struct device_node *node)
 	 */
 	clockevents_config_and_register(&moxart_clockevent, pclk,
 					0x4, 0xfffffffe);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(moxart, "moxa,moxart-timer", moxart_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(moxart, "moxa,moxart-timer", moxart_timer_init);
Signature · 1 line
1.9.1
#43 lore raw

PATCH v2 25/63 clocksource/drivers/mxs_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mps2-timer.c | 10 ++++++----
 drivers/clocksource/mxs_timer.c  |  2 +-
 2 files changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/mps2-timer.c +6 -4
index 3d33a5e..c303fa9 100644
@@ -250,7 +250,7 @@ out:
 	return ret;
 }
 
-static void __init mps2_timer_init(struct device_node *np)
+static int __init mps2_timer_init(struct device_node *np)
 {
 	static int has_clocksource, has_clockevent;
 	int ret;
@@ -259,7 +259,7 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clocksource_init(np);
 		if (!ret) {
 			has_clocksource = 1;
-			return;
+			return 0;
 		}
 	}
 
@@ -267,9 +267,11 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clockevent_init(np);
 		if (!ret) {
 			has_clockevent = 1;
-			return;
+			return 0;
 		}
 	}
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mps2_timer, "arm,mps2-timer", mps2_timer_init);
drivers/clocksource/mxs_timer.c +1 -1
index f5ce296..16cf53b 100644
@@ -226,7 +226,7 @@ static int __init mxs_clocksource_init(struct clk *timer_clk)
 	return 0;
 }
 
-static void __init mxs_timer_init(struct device_node *np)
+static int __init mxs_timer_init(struct device_node *np)
 {
 	struct clk *timer_clk;
 	int irq;
Signature · 1 line
1.9.1
#44 lore raw

Re: [PATCH V2 25/63] clocksource/drivers/mxs_timer: Convert init function to return error

Hello,

Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 8 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mps2-timer.c | 10 ++++++----
 drivers/clocksource/mxs_timer.c  |  2 +-

Did you forget to split here? The changelog only mentions mxs.

Quoted 43 lines
 2 files changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/mps2-timer.c +6 -4
index 3d33a5e..c303fa9 100644
@@ -250,7 +250,7 @@ out:
 	return ret;
 }
 
-static void __init mps2_timer_init(struct device_node *np)
+static int __init mps2_timer_init(struct device_node *np)
 {
 	static int has_clocksource, has_clockevent;
 	int ret;
@@ -259,7 +259,7 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clocksource_init(np);
 		if (!ret) {
 			has_clocksource = 1;
-			return;
+			return 0;
 		}
 	}
 
@@ -267,9 +267,11 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clockevent_init(np);
 		if (!ret) {
 			has_clockevent = 1;
-			return;
+			return 0;
 		}
 	}
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mps2_timer, "arm,mps2-timer", mps2_timer_init);
drivers/clocksource/mxs_timer.c +0 -0
index f5ce296..16cf53b 100644

drivers/clocksource/mxs_timer.c static int __init mxs_clocksource_init(struct clk *timer_clk) · line 232

Quoted 8 lines
drivers/clocksource/mxs_timer.c +1 -1
@@ -226,7 +226,7 @@ static int __init mxs_clocksource_init(struct clk *timer_clk)
 	return 0;
 }
 
-static void __init mxs_timer_init(struct device_node *np)
+static int __init mxs_timer_init(struct device_node *np)
 {
 	struct clk *timer_clk;
 	int irq;

I didn't try, but I expect that the "return;" a few lines below results in at least a warning and the compiler also warns about a missing return at the end of the function.

Best regards
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
#45 lore raw

PATCH v3 1/1 clocksource/drivers/mxs: Convert init function to return error

The init function does not return any error, it prints a message, returns and lets the caller unaware if the state of the system.

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mxs_timer.c | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)
drivers/clocksource/mxs_timer.c +18 -8
index f5ce296..17b9d19 100644
@@ -226,10 +226,10 @@ static int __init mxs_clocksource_init(struct clk *timer_clk)
 	return 0;
 }
 
-static void __init mxs_timer_init(struct device_node *np)
+static int __init mxs_timer_init(struct device_node *np)
 {
 	struct clk *timer_clk;
-	int irq;
+	int irq, ret;
 
 	mxs_timrot_base = of_iomap(np, 0);
 	WARN_ON(!mxs_timrot_base);
@@ -237,10 +237,12 @@ static void __init mxs_timer_init(struct device_node *np)
 	timer_clk = of_clk_get(np, 0);
 	if (IS_ERR(timer_clk)) {
 		pr_err("%s: failed to get clk\n", __func__);
-		return;
+		return PTR_ERR(timer_clk);
 	}
 
-	clk_prepare_enable(timer_clk);
+	ret = clk_prepare_enable(timer_clk);
+	if (ret)
+		return ret;
 
 	/*
 	 * Initialize timers to a known state
@@ -278,11 +280,19 @@ static void __init mxs_timer_init(struct device_node *np)
 			mxs_timrot_base + HW_TIMROT_FIXED_COUNTn(1));
 
 	/* init and register the timer to the framework */
-	mxs_clocksource_init(timer_clk);
-	mxs_clockevent_init(timer_clk);
+	ret = mxs_clocksource_init(timer_clk);
+	if (ret)
+		return ret;
+
+	ret = mxs_clockevent_init(timer_clk);
+	if (ret)
+		return ret;
 
 	/* Make irqs happen */
 	irq = irq_of_parse_and_map(np, 0);
-	setup_irq(irq, &mxs_timer_irq);
+	if (irq <= 0)
+		return -EINVAL;
+
+	return setup_irq(irq, &mxs_timer_irq);
 }
-CLOCKSOURCE_OF_DECLARE(mxs, "fsl,timrot", mxs_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mxs, "fsl,timrot", mxs_timer_init);
Signature · 1 line
1.9.1
maintainer
#46 lore raw

Re: [PATCH V2 25/63] clocksource/drivers/mxs_timer: Convert init function to return error

In reply to Daniel Lezcano
Quoted 74 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mps2-timer.c | 10 ++++++----
 drivers/clocksource/mxs_timer.c  |  2 +-
 2 files changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/mps2-timer.c +6 -4
index 3d33a5e..c303fa9 100644
@@ -250,7 +250,7 @@ out:
 	return ret;
 }
 
-static void __init mps2_timer_init(struct device_node *np)
+static int __init mps2_timer_init(struct device_node *np)
 {
 	static int has_clocksource, has_clockevent;
 	int ret;
@@ -259,7 +259,7 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clocksource_init(np);
 		if (!ret) {
 			has_clocksource = 1;
-			return;
+			return 0;
 		}
 	}
 
@@ -267,9 +267,11 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clockevent_init(np);
 		if (!ret) {
 			has_clockevent = 1;
-			return;
+			return 0;
 		}
 	}
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mps2_timer, "arm,mps2-timer", mps2_timer_init);
drivers/clocksource/mxs_timer.c +1 -1
index f5ce296..16cf53b 100644
@@ -226,7 +226,7 @@ static int __init mxs_clocksource_init(struct clk *timer_clk)
 	return 0;
 }
 
-static void __init mxs_timer_init(struct device_node *np)
+static int __init mxs_timer_init(struct device_node *np)
 {
 	struct clk *timer_clk;
 	int irq;
Signature · 1 line
1.9.1

This patch needs rework as it is changing (incompletely) two files that have different maintainers.

Best regards,
Liviu

Signature · 8 lines
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ?\_(?)_/?
#47 lore raw

Re: [PATCH V2 25/63] clocksource/drivers/mxs_timer: Convert init function to return error

Quoted 13 lines · Liviu Dudau
Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 6 lines
Quoted 6 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---

[ ... ]

Actually, this is fixed for mxs [1] (sorry the Cc script is misbehaving).

Quoted 2 lines

This patch needs rework as it is changing (incompletely) two files that have different maintainers.

Let me resend the mps2 driver.

Thanks.

-- Daniel

[1] http://www.spinics.net/lists/kernel/msg2281624.html

Signature · 5 lines
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#48 lore raw

PATCH v3 1/1 clocksource/drivers/mps2-timer: Convert init function to return error

In reply to Liviu Dudau

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mps2-timer.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/clocksource/mps2-timer.c +6 -4
index 3d33a5e..c303fa9 100644
@@ -250,7 +250,7 @@ out:
 	return ret;
 }
 
-static void __init mps2_timer_init(struct device_node *np)
+static int __init mps2_timer_init(struct device_node *np)
 {
 	static int has_clocksource, has_clockevent;
 	int ret;
@@ -259,7 +259,7 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clocksource_init(np);
 		if (!ret) {
 			has_clocksource = 1;
-			return;
+			return 0;
 		}
 	}
 
@@ -267,9 +267,11 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clockevent_init(np);
 		if (!ret) {
 			has_clockevent = 1;
-			return;
+			return 0;
 		}
 	}
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mps2_timer, "arm,mps2-timer", mps2_timer_init);
Signature · 1 line
1.9.1
maintainer Acked-by on v3 1/1
#49 lore raw

Re: [PATCH V3] clocksource/drivers/mps2-timer: Convert init function to return error

Quoted 60 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mps2-timer.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/clocksource/mps2-timer.c +6 -4
index 3d33a5e..c303fa9 100644
@@ -250,7 +250,7 @@ out:
 	return ret;
 }
 
-static void __init mps2_timer_init(struct device_node *np)
+static int __init mps2_timer_init(struct device_node *np)
 {
 	static int has_clocksource, has_clockevent;
 	int ret;
@@ -259,7 +259,7 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clocksource_init(np);
 		if (!ret) {
 			has_clocksource = 1;
-			return;
+			return 0;
 		}
 	}
 
@@ -267,9 +267,11 @@ static void __init mps2_timer_init(struct device_node *np)
 		ret = mps2_clockevent_init(np);
 		if (!ret) {
 			has_clockevent = 1;
-			return;
+			return 0;
 		}
 	}
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mps2_timer, "arm,mps2-timer", mps2_timer_init);
Signature · 1 line
1.9.1

Thanks!

Signature · 8 lines
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ?\_(?)_/?
#50 lore raw

PATCH v2 26/63 clocksource/drivers/nomadik-mtu: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/mxs_timer.c | 24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)
drivers/clocksource/mxs_timer.c +17 -7
index 16cf53b..17b9d19 100644
@@ -229,7 +229,7 @@ static int __init mxs_clocksource_init(struct clk *timer_clk)
 static int __init mxs_timer_init(struct device_node *np)
 {
 	struct clk *timer_clk;
-	int irq;
+	int irq, ret;
 
 	mxs_timrot_base = of_iomap(np, 0);
 	WARN_ON(!mxs_timrot_base);
@@ -237,10 +237,12 @@ static int __init mxs_timer_init(struct device_node *np)
 	timer_clk = of_clk_get(np, 0);
 	if (IS_ERR(timer_clk)) {
 		pr_err("%s: failed to get clk\n", __func__);
-		return;
+		return PTR_ERR(timer_clk);
 	}
 
-	clk_prepare_enable(timer_clk);
+	ret = clk_prepare_enable(timer_clk);
+	if (ret)
+		return ret;
 
 	/*
 	 * Initialize timers to a known state
@@ -278,11 +280,19 @@ static int __init mxs_timer_init(struct device_node *np)
 			mxs_timrot_base + HW_TIMROT_FIXED_COUNTn(1));
 
 	/* init and register the timer to the framework */
-	mxs_clocksource_init(timer_clk);
-	mxs_clockevent_init(timer_clk);
+	ret = mxs_clocksource_init(timer_clk);
+	if (ret)
+		return ret;
+
+	ret = mxs_clockevent_init(timer_clk);
+	if (ret)
+		return ret;
 
 	/* Make irqs happen */
 	irq = irq_of_parse_and_map(np, 0);
-	setup_irq(irq, &mxs_timer_irq);
+	if (irq <= 0)
+		return -EINVAL;
+
+	return setup_irq(irq, &mxs_timer_irq);
 }
-CLOCKSOURCE_OF_DECLARE(mxs, "fsl,timrot", mxs_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(mxs, "fsl,timrot", mxs_timer_init);
Signature · 1 line
1.9.1
#51 lore raw

PATCH v2 27/63 clocksource/drivers/pxa_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/nomadik-mtu.c | 45 +++++++++++++++++++++++++--------------
 1 file changed, 29 insertions(+), 16 deletions(-)
drivers/clocksource/nomadik-mtu.c +29 -16
index bc8dd44..d2be5b3 100644
@@ -193,10 +193,11 @@ static struct irqaction nmdk_timer_irq = {
 	.dev_id		= &nmdk_clkevt,
 };
 
-static void __init nmdk_timer_init(void __iomem *base, int irq,
+static int __init nmdk_timer_init(void __iomem *base, int irq,
 				   struct clk *pclk, struct clk *clk)
 {
 	unsigned long rate;
+	int ret;
 
 	mtu_base = base;
 
@@ -226,10 +227,12 @@ static void __init nmdk_timer_init(void __iomem *base, int irq,
 	/* Timer 0 is the free running clocksource */
 	nmdk_clksrc_reset();
 
-	if (clocksource_mmio_init(mtu_base + MTU_VAL(0), "mtu_0",
-			rate, 200, 32, clocksource_mmio_readl_down))
-		pr_err("timer: failed to initialize clock source %s\n",
-		       "mtu_0");
+	ret = clocksource_mmio_init(mtu_base + MTU_VAL(0), "mtu_0",
+				    rate, 200, 32, clocksource_mmio_readl_down);
+	if (ret) {
+		pr_err("timer: failed to initialize clock source %s\n", "mtu_0");
+		return ret;
+	}
 
 #ifdef CONFIG_CLKSRC_NOMADIK_MTU_SCHED_CLOCK
 	sched_clock_register(nomadik_read_sched_clock, 32, rate);
@@ -244,9 +247,11 @@ static void __init nmdk_timer_init(void __iomem *base, int irq,
 	mtu_delay_timer.read_current_timer = &nmdk_timer_read_current_timer;
 	mtu_delay_timer.freq = rate;
 	register_current_timer_delay(&mtu_delay_timer);
+
+	return 0;
 }
 
-static void __init nmdk_timer_of_init(struct device_node *node)
+static int __init nmdk_timer_of_init(struct device_node *node)
 {
 	struct clk *pclk;
 	struct clk *clk;
@@ -254,22 +259,30 @@ static void __init nmdk_timer_of_init(struct device_node *node)
 	int irq;
 
 	base = of_iomap(node, 0);
-	if (!base)
-		panic("Can't remap registers");
+	if (!base) {
+		pr_err("Can't remap registers");
+		return -ENXIO;
+	}
 
 	pclk = of_clk_get_by_name(node, "apb_pclk");
-	if (IS_ERR(pclk))
-		panic("could not get apb_pclk");
+	if (IS_ERR(pclk)) {
+		pr_err("could not get apb_pclk");
+		return PTR_ERR(pclk);
+	}
 
 	clk = of_clk_get_by_name(node, "timclk");
-	if (IS_ERR(clk))
-		panic("could not get timclk");
+	if (IS_ERR(clk)) {
+		pr_err("could not get timclk");
+		return PTR_ERR(clk);
+	}
 
 	irq = irq_of_parse_and_map(node, 0);
-	if (irq <= 0)
-		panic("Can't parse IRQ");
+	if (irq <= 0) {
+		pr_err("Can't parse IRQ");
+		return -EINVAL;
+	}
 
-	nmdk_timer_init(base, irq, pclk, clk);
+	return nmdk_timer_init(base, irq, pclk, clk);
 }
-CLOCKSOURCE_OF_DECLARE(nomadik_mtu, "st,nomadik-mtu",
+CLOCKSOURCE_OF_DECLARE_RET(nomadik_mtu, "st,nomadik-mtu",
 		       nmdk_timer_of_init);
Signature · 1 line
1.9.1
#52 lore raw

PATCH v2 28/63 clocksource/drivers/qcom-timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/pxa_timer.c | 46 +++++++++++++++++++++++++++++------------
 1 file changed, 33 insertions(+), 13 deletions(-)
drivers/clocksource/pxa_timer.c +33 -13
index 45b6a49..59af75c 100644
@@ -150,8 +150,10 @@ static struct irqaction pxa_ost0_irq = {
 	.dev_id		= &ckevt_pxa_osmr0,
 };
 
-static void __init pxa_timer_common_init(int irq, unsigned long clock_tick_rate)
+static int __init pxa_timer_common_init(int irq, unsigned long clock_tick_rate)
 {
+	int ret;
+
 	timer_writel(0, OIER);
 	timer_writel(OSSR_M0 | OSSR_M1 | OSSR_M2 | OSSR_M3, OSSR);
 
@@ -159,41 +161,59 @@ static void __init pxa_timer_common_init(int irq, unsigned long clock_tick_rate)
 
 	ckevt_pxa_osmr0.cpumask = cpumask_of(0);
 
-	setup_irq(irq, &pxa_ost0_irq);
+	ret = setup_irq(irq, &pxa_ost0_irq);
+	if (ret) {
+		pr_err("Failed to setup irq");
+		return ret;
+	}
+
+	ret = clocksource_mmio_init(timer_base + OSCR, "oscr0", clock_tick_rate, 200,
+				    32, clocksource_mmio_readl_up);
+	if (ret) {
+		pr_err("Failed to init clocksource");
+		return ret;
+	}
 
-	clocksource_mmio_init(timer_base + OSCR, "oscr0", clock_tick_rate, 200,
-			      32, clocksource_mmio_readl_up);
 	clockevents_config_and_register(&ckevt_pxa_osmr0, clock_tick_rate,
 					MIN_OSCR_DELTA * 2, 0x7fffffff);
+
+	return 0;
 }
 
-static void __init pxa_timer_dt_init(struct device_node *np)
+static int __init pxa_timer_dt_init(struct device_node *np)
 {
 	struct clk *clk;
-	int irq;
+	int irq, ret;
 
 	/* timer registers are shared with watchdog timer */
 	timer_base = of_iomap(np, 0);
-	if (!timer_base)
-		panic("%s: unable to map resource\n", np->name);
+	if (!timer_base) {
+		pr_err("%s: unable to map resource\n", np->name);
+		return -ENXIO;
+	}
 
 	clk = of_clk_get(np, 0);
 	if (IS_ERR(clk)) {
 		pr_crit("%s: unable to get clk\n", np->name);
-		return;
+		return PTR_ERR(clk);
+	}
+
+	ret = clk_prepare_enable(clk);
+	if (ret) {
+		pr_crit("Failed to prepare clock");
+		return ret;
 	}
-	clk_prepare_enable(clk);
 
 	/* we are only interested in OS-timer0 irq */
 	irq = irq_of_parse_and_map(np, 0);
 	if (irq <= 0) {
 		pr_crit("%s: unable to parse OS-timer0 irq\n", np->name);
-		return;
+		return -EINVAL;
 	}
 
-	pxa_timer_common_init(irq, clk_get_rate(clk));
+	return pxa_timer_common_init(irq, clk_get_rate(clk));
 }
-CLOCKSOURCE_OF_DECLARE(pxa_timer, "marvell,pxa-timer", pxa_timer_dt_init);
+CLOCKSOURCE_OF_DECLARE_RET(pxa_timer, "marvell,pxa-timer", pxa_timer_dt_init);
 
 /*
  * Legacy timer init for non device-tree boards.
Signature · 1 line
1.9.1
#53 lore raw

PATCH v2 29/63 clocksource/drivers/samsung_pwm_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/qcom-timer.c        | 27 +++++++++++++++------------
 drivers/clocksource/samsung_pwm_timer.c |  2 +-
 2 files changed, 16 insertions(+), 13 deletions(-)
drivers/clocksource/qcom-timer.c +15 -12
index f8e09f9..79f73bd 100644
@@ -178,7 +178,7 @@ static struct delay_timer msm_delay_timer = {
 	.read_current_timer = msm_read_current_timer,
 };
 
-static void __init msm_timer_init(u32 dgt_hz, int sched_bits, int irq,
+static int __init msm_timer_init(u32 dgt_hz, int sched_bits, int irq,
 				  bool percpu)
 {
 	struct clocksource *cs = &msm_clocksource;
@@ -218,12 +218,14 @@ err:
 	sched_clock_register(msm_sched_clock_read, sched_bits, dgt_hz);
 	msm_delay_timer.freq = dgt_hz;
 	register_current_timer_delay(&msm_delay_timer);
+
+	return res;
 }
 
-static void __init msm_dt_timer_init(struct device_node *np)
+static int __init msm_dt_timer_init(struct device_node *np)
 {
 	u32 freq;
-	int irq;
+	int irq, ret;
 	struct resource res;
 	u32 percpu_offset;
 	void __iomem *base;
@@ -232,34 +234,35 @@ static void __init msm_dt_timer_init(struct device_node *np)
 	base = of_iomap(np, 0);
 	if (!base) {
 		pr_err("Failed to map event base\n");
-		return;
+		return -ENXIO;
 	}
 
 	/* We use GPT0 for the clockevent */
 	irq = irq_of_parse_and_map(np, 1);
 	if (irq <= 0) {
 		pr_err("Can't get irq\n");
-		return;
+		return -EINVAL;
 	}
 
 	/* We use CPU0's DGT for the clocksource */
 	if (of_property_read_u32(np, "cpu-offset", &percpu_offset))
 		percpu_offset = 0;
 
-	if (of_address_to_resource(np, 0, &res)) {
+	ret = of_address_to_resource(np, 0, &res);
+	if (ret) {
 		pr_err("Failed to parse DGT resource\n");
-		return;
+		return ret;
 	}
 
 	cpu0_base = ioremap(res.start + percpu_offset, resource_size(&res));
 	if (!cpu0_base) {
 		pr_err("Failed to map source base\n");
-		return;
+		return -EINVAL;
 	}
 
 	if (of_property_read_u32(np, "clock-frequency", &freq)) {
 		pr_err("Unknown frequency\n");
-		return;
+		return -EINVAL;
 	}
 
 	event_base = base + 0x4;
@@ -268,7 +271,7 @@ static void __init msm_dt_timer_init(struct device_node *np)
 	freq /= 4;
 	writel_relaxed(DGT_CLK_CTL_DIV_4, source_base + DGT_CLK_CTL);
 
-	msm_timer_init(freq, 32, irq, !!percpu_offset);
+	return msm_timer_init(freq, 32, irq, !!percpu_offset);
 }
-CLOCKSOURCE_OF_DECLARE(kpss_timer, "qcom,kpss-timer", msm_dt_timer_init);
-CLOCKSOURCE_OF_DECLARE(scss_timer, "qcom,scss-timer", msm_dt_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(kpss_timer, "qcom,kpss-timer", msm_dt_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(scss_timer, "qcom,scss-timer", msm_dt_timer_init);
drivers/clocksource/samsung_pwm_timer.c +1 -1
index 47e0515..503a2f7 100644
@@ -499,7 +499,7 @@ static const struct samsung_pwm_variant s5p_variant = {
 
 static void __init s5p_pwm_clocksource_init(struct device_node *np)
 {
-	samsung_pwm_alloc(np, &s5p_variant);
+	return samsung_pwm_alloc(np, &s5p_variant);
 }
 CLOCKSOURCE_OF_DECLARE(s5pc100_pwm, "samsung,s5pc100-pwm", s5p_pwm_clocksource_init);
 #endif
Signature · 1 line
1.9.1
#54 lore raw

PATCH v2 30/63 clocksource/drivers/sun4i_time: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/samsung_pwm_timer.c | 60 ++++++++++++++++++---------------
 1 file changed, 32 insertions(+), 28 deletions(-)
drivers/clocksource/samsung_pwm_timer.c +32 -28
index 503a2f7..27a9797 100644
@@ -333,11 +333,10 @@ static u64 notrace samsung_read_sched_clock(void)
 	return samsung_clocksource_read(NULL);
 }
 
-static void __init samsung_clocksource_init(void)
+static int __init samsung_clocksource_init(void)
 {
 	unsigned long pclk;
 	unsigned long clock_rate;
-	int ret;
 
 	pclk = clk_get_rate(pwm.timerclk);
 
@@ -358,9 +357,7 @@ static void __init samsung_clocksource_init(void)
 						pwm.variant.bits, clock_rate);
 
 	samsung_clocksource.mask = CLOCKSOURCE_MASK(pwm.variant.bits);
-	ret = clocksource_register_hz(&samsung_clocksource, clock_rate);
-	if (ret)
-		panic("samsung_clocksource_timer: can't register clocksource\n");
+	return clocksource_register_hz(&samsung_clocksource, clock_rate);
 }
 
 static void __init samsung_timer_resources(void)
@@ -380,26 +377,31 @@ static void __init samsung_timer_resources(void)
 /*
  * PWM master driver
  */
-static void __init _samsung_pwm_clocksource_init(void)
+static int __init _samsung_pwm_clocksource_init(void)
 {
 	u8 mask;
 	int channel;
 
 	mask = ~pwm.variant.output_mask & ((1 << SAMSUNG_PWM_NUM) - 1);
 	channel = fls(mask) - 1;
-	if (channel < 0)
-		panic("failed to find PWM channel for clocksource");
+	if (channel < 0) {
+		pr_crit("failed to find PWM channel for clocksource");
+		return -EINVAL;
+	}
 	pwm.source_id = channel;
 
 	mask &= ~(1 << channel);
 	channel = fls(mask) - 1;
-	if (channel < 0)
-		panic("failed to find PWM channel for clock event");
+	if (channel < 0) {
+		pr_crit("failed to find PWM channel for clock event");
+		return -EINVAL;
+	}
 	pwm.event_id = channel;
 
 	samsung_timer_resources();
 	samsung_clockevent_init();
-	samsung_clocksource_init();
+
+	return samsung_clocksource_init();
 }
 
 void __init samsung_pwm_clocksource_init(void __iomem *base,
@@ -417,8 +419,8 @@ void __init samsung_pwm_clocksource_init(void __iomem *base,
 }
 
 #ifdef CONFIG_CLKSRC_OF
-static void __init samsung_pwm_alloc(struct device_node *np,
-				     const struct samsung_pwm_variant *variant)
+static int __init samsung_pwm_alloc(struct device_node *np,
+				    const struct samsung_pwm_variant *variant)
 {
 	struct property *prop;
 	const __be32 *cur;
@@ -441,14 +443,16 @@ static void __init samsung_pwm_alloc(struct device_node *np,
 	pwm.base = of_iomap(np, 0);
 	if (!pwm.base) {
 		pr_err("%s: failed to map PWM registers\n", __func__);
-		return;
+		return -ENXIO;
 	}
 
 	pwm.timerclk = of_clk_get_by_name(np, "timers");
-	if (IS_ERR(pwm.timerclk))
-		panic("failed to get timers clock for timer");
+	if (IS_ERR(pwm.timerclk)) {
+		pr_crit("failed to get timers clock for timer");
+		return PTR_ERR(pwm.timerclk);
+	}
 
-	_samsung_pwm_clocksource_init();
+	return _samsung_pwm_clocksource_init();
 }
 
 static const struct samsung_pwm_variant s3c24xx_variant = {
@@ -458,11 +462,11 @@ static const struct samsung_pwm_variant s3c24xx_variant = {
 	.tclk_mask	= (1 << 4),
 };
 
-static void __init s3c2410_pwm_clocksource_init(struct device_node *np)
+static int __init s3c2410_pwm_clocksource_init(struct device_node *np)
 {
-	samsung_pwm_alloc(np, &s3c24xx_variant);
+	return samsung_pwm_alloc(np, &s3c24xx_variant);
 }
-CLOCKSOURCE_OF_DECLARE(s3c2410_pwm, "samsung,s3c2410-pwm", s3c2410_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE_RET(s3c2410_pwm, "samsung,s3c2410-pwm", s3c2410_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s3c64xx_variant = {
 	.bits		= 32,
@@ -471,11 +475,11 @@ static const struct samsung_pwm_variant s3c64xx_variant = {
 	.tclk_mask	= (1 << 7) | (1 << 6) | (1 << 5),
 };
 
-static void __init s3c64xx_pwm_clocksource_init(struct device_node *np)
+static int __init s3c64xx_pwm_clocksource_init(struct device_node *np)
 {
-	samsung_pwm_alloc(np, &s3c64xx_variant);
+	return samsung_pwm_alloc(np, &s3c64xx_variant);
 }
-CLOCKSOURCE_OF_DECLARE(s3c6400_pwm, "samsung,s3c6400-pwm", s3c64xx_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE_RET(s3c6400_pwm, "samsung,s3c6400-pwm", s3c64xx_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s5p64x0_variant = {
 	.bits		= 32,
@@ -484,11 +488,11 @@ static const struct samsung_pwm_variant s5p64x0_variant = {
 	.tclk_mask	= 0,
 };
 
-static void __init s5p64x0_pwm_clocksource_init(struct device_node *np)
+static int __init s5p64x0_pwm_clocksource_init(struct device_node *np)
 {
-	samsung_pwm_alloc(np, &s5p64x0_variant);
+	return samsung_pwm_alloc(np, &s5p64x0_variant);
 }
-CLOCKSOURCE_OF_DECLARE(s5p6440_pwm, "samsung,s5p6440-pwm", s5p64x0_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE_RET(s5p6440_pwm, "samsung,s5p6440-pwm", s5p64x0_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s5p_variant = {
 	.bits		= 32,
@@ -497,9 +501,9 @@ static const struct samsung_pwm_variant s5p_variant = {
 	.tclk_mask	= (1 << 5),
 };
 
-static void __init s5p_pwm_clocksource_init(struct device_node *np)
+static int __init s5p_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s5p_variant);
 }
-CLOCKSOURCE_OF_DECLARE(s5pc100_pwm, "samsung,s5pc100-pwm", s5p_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE_RET(s5pc100_pwm, "samsung,s5pc100-pwm", s5p_pwm_clocksource_init);
 #endif
Signature · 1 line
1.9.1
#55 lore raw

PATCH v2 31/63 clocksource/drivers/tango_xtal: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/sun4i_timer.c | 45 ++++++++++++++++++++++++++++-----------
 1 file changed, 32 insertions(+), 13 deletions(-)
drivers/clocksource/sun4i_timer.c +32 -13
index 6f3719d..4453730 100644
@@ -146,7 +146,7 @@ static u64 notrace sun4i_timer_sched_read(void)
 	return ~readl(timer_base + TIMER_CNTVAL_REG(1));
 }
 
-static void __init sun4i_timer_init(struct device_node *node)
+static int __init sun4i_timer_init(struct device_node *node)
 {
 	unsigned long rate = 0;
 	struct clk *clk;
@@ -154,17 +154,28 @@ static void __init sun4i_timer_init(struct device_node *node)
 	u32 val;
 
 	timer_base = of_iomap(node, 0);
-	if (!timer_base)
-		panic("Can't map registers");
+	if (!timer_base) {
+		pr_crit("Can't map registers");
+		return -ENXIO;
+	}
 
 	irq = irq_of_parse_and_map(node, 0);
-	if (irq <= 0)
-		panic("Can't parse IRQ");
+	if (irq <= 0) {
+		pr_crit("Can't parse IRQ");
+		return -EINVAL;
+	}
 
 	clk = of_clk_get(node, 0);
-	if (IS_ERR(clk))
-		panic("Can't get timer clock");
-	clk_prepare_enable(clk);
+	if (IS_ERR(clk)) {
+		pr_crit("Can't get timer clock");
+		return PTR_ERR(clk);
+	}
+
+	ret = clk_prepare_enable(clk);
+	if (ret) {
+		pr_err("Failed to prepare clock");
+		return ret;
+	}
 
 	rate = clk_get_rate(clk);
 
@@ -182,8 +193,12 @@ static void __init sun4i_timer_init(struct device_node *node)
 	    of_machine_is_compatible("allwinner,sun5i-a10s"))
 		sched_clock_register(sun4i_timer_sched_read, 32, rate);
 
-	clocksource_mmio_init(timer_base + TIMER_CNTVAL_REG(1), node->name,
-			      rate, 350, 32, clocksource_mmio_readl_down);
+	ret = clocksource_mmio_init(timer_base + TIMER_CNTVAL_REG(1), node->name,
+				    rate, 350, 32, clocksource_mmio_readl_down);
+	if (ret) {
+		pr_err("Failed to register clocksource");
+		return ret;
+	}
 
 	ticks_per_jiffy = DIV_ROUND_UP(rate, HZ);
 
@@ -200,12 +215,16 @@ static void __init sun4i_timer_init(struct device_node *node)
 					TIMER_SYNC_TICKS, 0xffffffff);
 
 	ret = setup_irq(irq, &sun4i_timer_irq);
-	if (ret)
-		pr_warn("failed to setup irq %d\n", irq);
+	if (ret) {
+		pr_err("failed to setup irq %d\n", irq);
+		return ret;
+	}
 
 	/* Enable timer0 interrupt */
 	val = readl(timer_base + TIMER_IRQ_EN_REG);
 	writel(val | TIMER_IRQ_EN(0), timer_base + TIMER_IRQ_EN_REG);
+
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(sun4i, "allwinner,sun4i-a10-timer",
+CLOCKSOURCE_OF_DECLARE_RET(sun4i, "allwinner,sun4i-a10-timer",
 		       sun4i_timer_init);
Signature · 1 line
1.9.1
#56 lore raw

Re: [PATCH V2 31/63] clocksource/drivers/tango_xtal: Convert init function to return error

Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 8 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/sun4i_timer.c | 45 ++++++++++++++++++++++++++++-----------
 1 file changed, 32 insertions(+), 13 deletions(-)

NACK ;-)

The subject specifies tango_xtal, but the patch changes sun4i_timer. (Looks like all patches in the series are off by one.) And I see you've already acknowledged the issue an hour ago.

The actual patch for tango_xtal is [PATCH V2 32/63] clocksource/drivers/tegra20_timer

BTW, I wasn't CCed on the tango_xtal patch.
I suppose I forgot to add the appropriate line in MAINTAINERS?

Regards.

#57 lore raw

PATCH v3 1/1 clocksource/drivers/tango_xtal: Convert init function to return error

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/tango_xtal.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/tango_xtal.c +7 -5
index c407c47..7dc716c 100644
@@ -19,7 +19,7 @@ static u64 notrace read_sched_clock(void)
 	return read_xtal_counter();
 }
 
-static void __init tango_clocksource_init(struct device_node *np)
+static int __init tango_clocksource_init(struct device_node *np)
 {
 	struct clk *clk;
 	int xtal_freq, ret;
@@ -27,13 +27,13 @@ static void __init tango_clocksource_init(struct device_node *np)
 	xtal_in_cnt = of_iomap(np, 0);
 	if (xtal_in_cnt == NULL) {
 		pr_err("%s: invalid address\n", np->full_name);
-		return;
+		return -ENXIO;
 	}
 
 	clk = of_clk_get(np, 0);
 	if (IS_ERR(clk)) {
 		pr_err("%s: invalid clock\n", np->full_name);
-		return;
+		return PTR_ERR(clk);
 	}
 
 	xtal_freq = clk_get_rate(clk);
@@ -44,11 +44,13 @@ static void __init tango_clocksource_init(struct device_node *np)
 				    32, clocksource_mmio_readl_up);
 	if (ret) {
 		pr_err("%s: registration failed\n", np->full_name);
-		return;
+		return ret;
 	}
 
 	sched_clock_register(read_sched_clock, 32, xtal_freq);
 	register_current_timer_delay(&delay_timer);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(tango, "sigma,tick-counter", tango_clocksource_init);
+CLOCKSOURCE_OF_DECLARE_RET(tango, "sigma,tick-counter", tango_clocksource_init);
Signature · 1 line
1.9.1
Acked-by on v3 1/1
#58 lore raw

Re: [PATCH V3] clocksource/drivers/tango_xtal: Convert init function to return error

Quoted 8 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

^^^ ^^
"leave the caller unaware of [...]" (?)

Quoted 5 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init

                                 ^^^^^^^^^^^

"just returns an error code from the init function" (?)

Quoted 42 lines

function.

---
 drivers/clocksource/tango_xtal.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/tango_xtal.c +4 -4
index c407c47..7dc716c 100644
@@ -19,7 +19,7 @@ static u64 notrace read_sched_clock(void)
 	return read_xtal_counter();
 }
 
-static void __init tango_clocksource_init(struct device_node *np)
+static int __init tango_clocksource_init(struct device_node *np)
 {
 	struct clk *clk;
 	int xtal_freq, ret;
@@ -27,13 +27,13 @@ static void __init tango_clocksource_init(struct device_node *np)
 	xtal_in_cnt = of_iomap(np, 0);
 	if (xtal_in_cnt == NULL) {
 		pr_err("%s: invalid address\n", np->full_name);
-		return;
+		return -ENXIO;
 	}
 
 	clk = of_clk_get(np, 0);
 	if (IS_ERR(clk)) {
 		pr_err("%s: invalid clock\n", np->full_name);
-		return;
+		return PTR_ERR(clk);
 	}
 
 	xtal_freq = clk_get_rate(clk);
@@ -44,11 +44,13 @@ static void __init tango_clocksource_init(struct device_node *np)
 				    32, clocksource_mmio_readl_up);
 	if (ret) {
 		pr_err("%s: registration failed\n", np->full_name);
-		return;
+		return ret;

drivers/clocksource/tango_xtal.c static void __init tango_clocksource_init(struct device_node *np) · line 56

Quoted 10 lines
drivers/clocksource/tango_xtal.c +3 -1
 	}
 
 	sched_clock_register(read_sched_clock, 32, xtal_freq);
 	register_current_timer_delay(&delay_timer);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(tango, "sigma,tick-counter", tango_clocksource_init);
+CLOCKSOURCE_OF_DECLARE_RET(tango, "sigma,tick-counter", tango_clocksource_init);

The code looks good to me.

Could you merge, on top of these, the patch we discussed a few weeks ago for changing ret to err? (I will attach the patch to this message.)

Regards.

#59 lore raw

Re: [PATCH V3] clocksource/drivers/tango_xtal: Convert init function to return error

Quoted 13 lines · Marc Gonzalez
Quoted 8 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

^^^ ^^
"leave the caller unaware of [...]" (?)

Quoted 7 lines
Quoted 5 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init

                                  ^^^^^^^^^^^

"just returns an error code from the init function" (?)

Ok, I will do the change when adding the acked-by tag.

[ ... ]

Quoted 5 lines

The code looks good to me.

Could you merge, on top of these, the patch we discussed a few weeks ago for changing ret to err? (I will attach the patch to this message.)

I don't really mind to convert 'ret' to 'err' if it is your preference but can it wait after the changes I initiated ? Much more patches will come to consolidate the init functions.

Signature · 5 lines
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#60 lore raw

PATCH v2 32/63 clocksource/drivers/tegra20_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/tango_xtal.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/tango_xtal.c +7 -5
index c407c47..7dc716c 100644
@@ -19,7 +19,7 @@ static u64 notrace read_sched_clock(void)
 	return read_xtal_counter();
 }
 
-static void __init tango_clocksource_init(struct device_node *np)
+static int __init tango_clocksource_init(struct device_node *np)
 {
 	struct clk *clk;
 	int xtal_freq, ret;
@@ -27,13 +27,13 @@ static void __init tango_clocksource_init(struct device_node *np)
 	xtal_in_cnt = of_iomap(np, 0);
 	if (xtal_in_cnt == NULL) {
 		pr_err("%s: invalid address\n", np->full_name);
-		return;
+		return -ENXIO;
 	}
 
 	clk = of_clk_get(np, 0);
 	if (IS_ERR(clk)) {
 		pr_err("%s: invalid clock\n", np->full_name);
-		return;
+		return PTR_ERR(clk);
 	}
 
 	xtal_freq = clk_get_rate(clk);
@@ -44,11 +44,13 @@ static void __init tango_clocksource_init(struct device_node *np)
 				    32, clocksource_mmio_readl_up);
 	if (ret) {
 		pr_err("%s: registration failed\n", np->full_name);
-		return;
+		return ret;
 	}
 
 	sched_clock_register(read_sched_clock, 32, xtal_freq);
 	register_current_timer_delay(&delay_timer);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(tango, "sigma,tick-counter", tango_clocksource_init);
+CLOCKSOURCE_OF_DECLARE_RET(tango, "sigma,tick-counter", tango_clocksource_init);
Signature · 1 line
1.9.1
#61 lore raw

PATCH v2 33/63 clocksource/drivers/time-armada-370-xp: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/tegra20_timer.c | 28 ++++++++++++++++------------
 1 file changed, 16 insertions(+), 12 deletions(-)
drivers/clocksource/tegra20_timer.c +16 -12
index 7b94ad2..543c37e 100644
@@ -165,7 +165,7 @@ static struct irqaction tegra_timer_irq = {
 	.dev_id		= &tegra_clockevent,
 };
 
-static void __init tegra20_init_timer(struct device_node *np)
+static int __init tegra20_init_timer(struct device_node *np)
 {
 	struct clk *clk;
 	unsigned long rate;
@@ -174,13 +174,13 @@ static void __init tegra20_init_timer(struct device_node *np)
 	timer_reg_base = of_iomap(np, 0);
 	if (!timer_reg_base) {
 		pr_err("Can't map timer registers\n");
-		BUG();
+		return -ENXIO;
 	}
 
 	tegra_timer_irq.irq = irq_of_parse_and_map(np, 2);
 	if (tegra_timer_irq.irq <= 0) {
 		pr_err("Failed to map timer IRQ\n");
-		BUG();
+		return -EINVAL;
 	}
 
 	clk = of_clk_get(np, 0);
@@ -211,10 +211,12 @@ static void __init tegra20_init_timer(struct device_node *np)
 
 	sched_clock_register(tegra_read_sched_clock, 32, 1000000);
 
-	if (clocksource_mmio_init(timer_reg_base + TIMERUS_CNTR_1US,
-		"timer_us", 1000000, 300, 32, clocksource_mmio_readl_up)) {
+	ret = clocksource_mmio_init(timer_reg_base + TIMERUS_CNTR_1US,
+				    "timer_us", 1000000, 300, 32,
+				    clocksource_mmio_readl_up);
+	if (ret) {
 		pr_err("Failed to register clocksource\n");
-		BUG();
+		return ret;
 	}
 
 	tegra_delay_timer.read_current_timer =
@@ -225,24 +227,26 @@ static void __init tegra20_init_timer(struct device_node *np)
 	ret = setup_irq(tegra_timer_irq.irq, &tegra_timer_irq);
 	if (ret) {
 		pr_err("Failed to register timer IRQ: %d\n", ret);
-		BUG();
+		return ret;
 	}
 
 	tegra_clockevent.cpumask = cpu_all_mask;
 	tegra_clockevent.irq = tegra_timer_irq.irq;
 	clockevents_config_and_register(&tegra_clockevent, 1000000,
 					0x1, 0x1fffffff);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(tegra20_timer, "nvidia,tegra20-timer", tegra20_init_timer);
+CLOCKSOURCE_OF_DECLARE_RET(tegra20_timer, "nvidia,tegra20-timer", tegra20_init_timer);
 
-static void __init tegra20_init_rtc(struct device_node *np)
+static int __init tegra20_init_rtc(struct device_node *np)
 {
 	struct clk *clk;
 
 	rtc_base = of_iomap(np, 0);
 	if (!rtc_base) {
 		pr_err("Can't map RTC registers");
-		BUG();
+		return -ENXIO;
 	}
 
 	/*
@@ -255,6 +259,6 @@ static void __init tegra20_init_rtc(struct device_node *np)
 	else
 		clk_prepare_enable(clk);
 
-	register_persistent_clock(NULL, tegra_read_persistent_clock64);
+	return register_persistent_clock(NULL, tegra_read_persistent_clock64);
 }
-CLOCKSOURCE_OF_DECLARE(tegra20_rtc, "nvidia,tegra20-rtc", tegra20_init_rtc);
+CLOCKSOURCE_OF_DECLARE_RET(tegra20_rtc, "nvidia,tegra20-rtc", tegra20_init_rtc);
Signature · 1 line
1.9.1
maintainer
#62 lore raw

Re: [PATCH V2 33/63] clocksource/drivers/time-armada-370-xp: Convert init function to return error

Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 8 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/tegra20_timer.c | 28 ++++++++++++++++------------
 1 file changed, 16 insertions(+), 12 deletions(-)

The $subject does not appear to match with the driver you are modifying here.

Cheers
Jon

Signature · 1 line
nvpublic
#63 lore raw

Re: [PATCH V2 33/63] clocksource/drivers/time-armada-370-xp: Convert init function to return error

Quoted 18 lines · Jon Hunter
Quoted 16 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Quoted 7 lines
Quoted 4 lines
---
  drivers/clocksource/tegra20_timer.c | 28 ++++++++++++++++------------
  1 file changed, 16 insertions(+), 12 deletions(-)

The $subject does not appear to match with the driver you are modifying here.

Ah, crap. I introduced a shift somewhere in the patchset. Fixed.

Thanks !

-- Daniel

Signature · 5 lines
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#64 lore raw

PATCH v3 1/1 clocksource/drivers/tegra20: Convert init function to return error

In reply to Jon Hunter

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/tegra20_timer.c | 28 ++++++++++++++++------------
 1 file changed, 16 insertions(+), 12 deletions(-)
drivers/clocksource/tegra20_timer.c +16 -12
index 7b94ad2..543c37e 100644
@@ -165,7 +165,7 @@ static struct irqaction tegra_timer_irq = {
 	.dev_id		= &tegra_clockevent,
 };
 
-static void __init tegra20_init_timer(struct device_node *np)
+static int __init tegra20_init_timer(struct device_node *np)
 {
 	struct clk *clk;
 	unsigned long rate;
@@ -174,13 +174,13 @@ static void __init tegra20_init_timer(struct device_node *np)
 	timer_reg_base = of_iomap(np, 0);
 	if (!timer_reg_base) {
 		pr_err("Can't map timer registers\n");
-		BUG();
+		return -ENXIO;
 	}
 
 	tegra_timer_irq.irq = irq_of_parse_and_map(np, 2);
 	if (tegra_timer_irq.irq <= 0) {
 		pr_err("Failed to map timer IRQ\n");
-		BUG();
+		return -EINVAL;
 	}
 
 	clk = of_clk_get(np, 0);
@@ -211,10 +211,12 @@ static void __init tegra20_init_timer(struct device_node *np)
 
 	sched_clock_register(tegra_read_sched_clock, 32, 1000000);
 
-	if (clocksource_mmio_init(timer_reg_base + TIMERUS_CNTR_1US,
-		"timer_us", 1000000, 300, 32, clocksource_mmio_readl_up)) {
+	ret = clocksource_mmio_init(timer_reg_base + TIMERUS_CNTR_1US,
+				    "timer_us", 1000000, 300, 32,
+				    clocksource_mmio_readl_up);
+	if (ret) {
 		pr_err("Failed to register clocksource\n");
-		BUG();
+		return ret;
 	}
 
 	tegra_delay_timer.read_current_timer =
@@ -225,24 +227,26 @@ static void __init tegra20_init_timer(struct device_node *np)
 	ret = setup_irq(tegra_timer_irq.irq, &tegra_timer_irq);
 	if (ret) {
 		pr_err("Failed to register timer IRQ: %d\n", ret);
-		BUG();
+		return ret;
 	}
 
 	tegra_clockevent.cpumask = cpu_all_mask;
 	tegra_clockevent.irq = tegra_timer_irq.irq;
 	clockevents_config_and_register(&tegra_clockevent, 1000000,
 					0x1, 0x1fffffff);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(tegra20_timer, "nvidia,tegra20-timer", tegra20_init_timer);
+CLOCKSOURCE_OF_DECLARE_RET(tegra20_timer, "nvidia,tegra20-timer", tegra20_init_timer);
 
-static void __init tegra20_init_rtc(struct device_node *np)
+static int __init tegra20_init_rtc(struct device_node *np)
 {
 	struct clk *clk;
 
 	rtc_base = of_iomap(np, 0);
 	if (!rtc_base) {
 		pr_err("Can't map RTC registers");
-		BUG();
+		return -ENXIO;
 	}
 
 	/*
@@ -255,6 +259,6 @@ static void __init tegra20_init_rtc(struct device_node *np)
 	else
 		clk_prepare_enable(clk);
 
-	register_persistent_clock(NULL, tegra_read_persistent_clock64);
+	return register_persistent_clock(NULL, tegra_read_persistent_clock64);
 }
-CLOCKSOURCE_OF_DECLARE(tegra20_rtc, "nvidia,tegra20-rtc", tegra20_init_rtc);
+CLOCKSOURCE_OF_DECLARE_RET(tegra20_rtc, "nvidia,tegra20-rtc", tegra20_init_rtc);
Signature · 1 line
1.9.1
#65 lore raw

PATCH v2 34/63 clocksource/drivers/time-efm32: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/time-armada-370-xp.c | 102 +++++++++++++++++++++++--------
 1 file changed, 76 insertions(+), 26 deletions(-)
drivers/clocksource/time-armada-370-xp.c +76 -26
index 601dbf74..bc4ab48 100644
@@ -260,14 +260,22 @@ static struct delay_timer armada_370_delay_timer = {
 	.read_current_timer = armada_370_delay_timer_read,
 };
 
-static void __init armada_370_xp_timer_common_init(struct device_node *np)
+static int __init armada_370_xp_timer_common_init(struct device_node *np)
 {
 	u32 clr = 0, set = 0;
 	int res;
 
 	timer_base = of_iomap(np, 0);
-	WARN_ON(!timer_base);
+	if (!timer_base) {
+		pr_err("Failed to iomap");
+		return -ENXIO;
+	}
+
 	local_base = of_iomap(np, 1);
+	if (!local_base) {
+		pr_err("Failed to iomap");
+		return -ENXIO;
+	}
 
 	if (timer25Mhz) {
 		set = TIMER0_25MHZ;		
@@ -306,14 +314,19 @@ static void __init armada_370_xp_timer_common_init(struct device_node *np)
 	 */
 	sched_clock_register(armada_370_xp_read_sched_clock, 32, timer_clk);
 
-	clocksource_mmio_init(timer_base + TIMER0_VAL_OFF,
-			      "armada_370_xp_clocksource",
-			      timer_clk, 300, 32, clocksource_mmio_readl_down);
+	res = clocksource_mmio_init(timer_base + TIMER0_VAL_OFF,
+				    "armada_370_xp_clocksource",
+				    timer_clk, 300, 32, clocksource_mmio_readl_down);
+	if (res) {
+		pr_err("Failed to initialize clocksource mmio");
+		return res;
+	}
 
 	register_cpu_notifier(&armada_370_xp_timer_cpu_nb);
 
 	armada_370_xp_evt = alloc_percpu(struct clock_event_device);
-
+	if (!armada_370_xp_evt)
+		return -ENOMEM;
 
 	/*
 	 * Setup clockevent timer (interrupt-driven).
@@ -323,33 +336,54 @@ static void __init armada_370_xp_timer_common_init(struct device_node *np)
 				"armada_370_xp_per_cpu_tick",
 				armada_370_xp_evt);
 	/* Immediately configure the timer on the boot CPU */
-	if (!res)
-		armada_370_xp_timer_setup(this_cpu_ptr(armada_370_xp_evt));
+	if (res) {
+		pr_err("Failed to request percpu irq");
+		return res;
+	}
+
+	res = armada_370_xp_timer_setup(this_cpu_ptr(armada_370_xp_evt));
+	if (!res) {
+		pr_err("Failed to setup timer");
+		return res;
+	}
 
 	register_syscore_ops(&armada_370_xp_timer_syscore_ops);
+	
+	return 0;
 }
 
-static void __init armada_xp_timer_init(struct device_node *np)
+static int __init armada_xp_timer_init(struct device_node *np)
 {
 	struct clk *clk = of_clk_get_by_name(np, "fixed");
+	int ret;
+
+	clk = of_clk_get(np, 0);
+	if (IS_ERR(clk)) {
+		pr_err("Failed to get clock");
+		return PTR_ERR(clk);
+	}
+
+	ret = clk_prepare_enable(clk);
+	if (ret)
+		return ret;
 
-	/* The 25Mhz fixed clock is mandatory, and must always be available */
-	BUG_ON(IS_ERR(clk));
-	clk_prepare_enable(clk);
 	timer_clk = clk_get_rate(clk);
 
-	armada_370_xp_timer_common_init(np);
+	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE(armada_xp, "marvell,armada-xp-timer",
+CLOCKSOURCE_OF_DECLARE_RET(armada_xp, "marvell,armada-xp-timer",
 		       armada_xp_timer_init);
 
-static void __init armada_375_timer_init(struct device_node *np)
+static int __init armada_375_timer_init(struct device_node *np)
 {
 	struct clk *clk;
+	int ret;
 
 	clk = of_clk_get_by_name(np, "fixed");
 	if (!IS_ERR(clk)) {
-		clk_prepare_enable(clk);
+		ret = clk_prepare_enable(clk);
+		if (ret)
+			return ret;
 		timer_clk = clk_get_rate(clk);
 	} else {
 
@@ -360,27 +394,43 @@ static void __init armada_375_timer_init(struct device_node *np)
 		clk = of_clk_get(np, 0);
 
 		/* Must have at least a clock */
-		BUG_ON(IS_ERR(clk));
-		clk_prepare_enable(clk);
+		if (IS_ERR(clk)) {
+			pr_err("Failed to get clock");
+			return PTR_ERR(clk);
+		}
+
+		ret = clk_prepare_enable(clk);
+		if (ret)
+			return ret;
+
 		timer_clk = clk_get_rate(clk) / TIMER_DIVIDER;
 		timer25Mhz = false;
 	}
 
-	armada_370_xp_timer_common_init(np);
+	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE(armada_375, "marvell,armada-375-timer",
+CLOCKSOURCE_OF_DECLARE_RET(armada_375, "marvell,armada-375-timer",
 		       armada_375_timer_init);
 
-static void __init armada_370_timer_init(struct device_node *np)
+static int __init armada_370_timer_init(struct device_node *np)
 {
-	struct clk *clk = of_clk_get(np, 0);
+	struct clk *clk;
+	int ret;
+
+	clk = of_clk_get(np, 0);
+	if (IS_ERR(clk)) {
+		pr_err("Failed to get clock");
+		return PTR_ERR(clk);
+	}
+
+	ret = clk_prepare_enable(clk);
+	if (ret)
+		return ret;
 
-	BUG_ON(IS_ERR(clk));
-	clk_prepare_enable(clk);
 	timer_clk = clk_get_rate(clk) / TIMER_DIVIDER;
 	timer25Mhz = false;
 
-	armada_370_xp_timer_common_init(np);
+	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE(armada_370, "marvell,armada-370-timer",
+CLOCKSOURCE_OF_DECLARE_RET(armada_370, "marvell,armada-370-timer",
 		       armada_370_timer_init);
Signature · 1 line
1.9.1
#66 lore raw

PATCH v2 35/63 clocksource/drivers/time-lpc32xx: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/time-efm32.c | 20 +++++++++++++-------
 1 file changed, 13 insertions(+), 7 deletions(-)
drivers/clocksource/time-efm32.c +13 -7
index b06e4c2..b71ffc6 100644
@@ -233,7 +233,11 @@ static int __init efm32_clockevent_init(struct device_node *np)
 					DIV_ROUND_CLOSEST(rate, 1024),
 					0xf, 0xffff);
 
-	setup_irq(irq, &efm32_clock_event_irq);
+	ret = setup_irq(irq, &efm32_clock_event_irq);
+	if (ret) {
+		pr_err("Failed setup irq");
+		goto err_get_irq;
+	}
 
 	return 0;
 
@@ -255,16 +259,16 @@ err_clk_get:
  * This function asserts that we have exactly one clocksource and one
  * clock_event_device in the end.
  */
-static void __init efm32_timer_init(struct device_node *np)
+static int __init efm32_timer_init(struct device_node *np)
 {
 	static int has_clocksource, has_clockevent;
-	int ret;
+	int ret = 0;
 
 	if (!has_clocksource) {
 		ret = efm32_clocksource_init(np);
 		if (!ret) {
 			has_clocksource = 1;
-			return;
+			return 0;
 		}
 	}
 
@@ -272,9 +276,11 @@ static void __init efm32_timer_init(struct device_node *np)
 		ret = efm32_clockevent_init(np);
 		if (!ret) {
 			has_clockevent = 1;
-			return;
+			return 0;
 		}
 	}
+
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(efm32compat, "efm32,timer", efm32_timer_init);
-CLOCKSOURCE_OF_DECLARE(efm32, "energymicro,efm32-timer", efm32_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(efm32compat, "efm32,timer", efm32_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(efm32, "energymicro,efm32-timer", efm32_timer_init);
Signature · 1 line
1.9.1
#67 lore raw

Re: [PATCH V2 35/63] clocksource/drivers/time-lpc32xx: Convert init function to return error

Hello Daniel,

$Subject ~= s/lpc32xx/efm32/

Quoted 8 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

These are both wrong for efm32. It doesn't panic and doesn't print an error message (obviously the "let the caller unaware" part is true).

Quoted 6 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Apart from the comment below the error handling is already fine in this driver.

Quoted 10 lines
---
 drivers/clocksource/time-efm32.c | 20 +++++++++++++-------
 1 file changed, 13 insertions(+), 7 deletions(-)
drivers/clocksource/time-efm32.c +0 -0
index b06e4c2..b71ffc6 100644

drivers/clocksource/time-efm32.c static int __init efm32_clockevent_init(struct device_node *np) · line 239

Quoted 8 lines
drivers/clocksource/time-efm32.c +4 -1
@@ -233,7 +233,11 @@ static int __init efm32_clockevent_init(struct device_node *np)
 					DIV_ROUND_CLOSEST(rate, 1024),
 					0xf, 0xffff);
 
-	setup_irq(irq, &efm32_clock_event_irq);
+	ret = setup_irq(irq, &efm32_clock_event_irq);
+	if (ret) {
+		pr_err("Failed setup irq");
+		goto err_get_irq;

I would prefer to introduce another label "err_setup_irq" at the same place as err_get_irq and use it here.

drivers/clocksource/time-efm32.c static int __init efm32_clockevent_init(struct device_node *np) · line 243

Quoted 4 lines
drivers/clocksource/time-efm32.c +1 -0
+	}
 
 	return 0;
 

Best regards
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
#68 lore raw

PATCH v3 1/1 clocksource/drivers/time-efm32: Convert init function to return error

The init functions do not return any error and let the caller unaware of the state of the system.

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/time-efm32.c | 21 ++++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)
drivers/clocksource/time-efm32.c +14 -7
index b06e4c2..6e2f79f 100644
@@ -233,10 +233,15 @@ static int __init efm32_clockevent_init(struct device_node *np)
 					DIV_ROUND_CLOSEST(rate, 1024),
 					0xf, 0xffff);
 
-	setup_irq(irq, &efm32_clock_event_irq);
+	ret = setup_irq(irq, &efm32_clock_event_irq);
+	if (ret) {
+		pr_err("Failed setup irq");
+		goto err_setup_irq;
+	}
 
 	return 0;
 
+err_setup_irq:
 err_get_irq:
 
 	iounmap(base);
@@ -255,16 +260,16 @@ err_clk_get:
  * This function asserts that we have exactly one clocksource and one
  * clock_event_device in the end.
  */
-static void __init efm32_timer_init(struct device_node *np)
+static int __init efm32_timer_init(struct device_node *np)
 {
 	static int has_clocksource, has_clockevent;
-	int ret;
+	int ret = 0;
 
 	if (!has_clocksource) {
 		ret = efm32_clocksource_init(np);
 		if (!ret) {
 			has_clocksource = 1;
-			return;
+			return 0;
 		}
 	}
 
@@ -272,9 +277,11 @@ static void __init efm32_timer_init(struct device_node *np)
 		ret = efm32_clockevent_init(np);
 		if (!ret) {
 			has_clockevent = 1;
-			return;
+			return 0;
 		}
 	}
+
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(efm32compat, "efm32,timer", efm32_timer_init);
-CLOCKSOURCE_OF_DECLARE(efm32, "energymicro,efm32-timer", efm32_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(efm32compat, "efm32,timer", efm32_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(efm32, "energymicro,efm32-timer", efm32_timer_init);
Signature · 1 line
1.9.1
Acked-by on v3 1/1
#69 lore raw

Re: [PATCH V3] clocksource/drivers/time-efm32: Convert init function to return error

Quoted 11 lines · Daniel Lezcano

The init functions do not return any error and let the caller unaware of the state of the system.

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Thanks
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
#70 lore raw

PATCH v2 36/63 clocksource/drivers/time-orion: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/time-lpc32xx.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/time-lpc32xx.c +7 -5
index daae61e..cb5b866 100644
@@ -288,16 +288,16 @@ err_clk_enable:
  * This function asserts that we have exactly one clocksource and one
  * clock_event_device in the end.
  */
-static void __init lpc32xx_timer_init(struct device_node *np)
+static int __init lpc32xx_timer_init(struct device_node *np)
 {
 	static int has_clocksource, has_clockevent;
-	int ret;
+	int ret = 0;
 
 	if (!has_clocksource) {
 		ret = lpc32xx_clocksource_init(np);
 		if (!ret) {
 			has_clocksource = 1;
-			return;
+			return 0;
 		}
 	}
 
@@ -305,8 +305,10 @@ static void __init lpc32xx_timer_init(struct device_node *np)
 		ret = lpc32xx_clockevent_init(np);
 		if (!ret) {
 			has_clockevent = 1;
-			return;
+			return 0;
 		}
 	}
+
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(lpc32xx_timer, "nxp,lpc3220-timer", lpc32xx_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(lpc32xx_timer, "nxp,lpc3220-timer", lpc32xx_timer_init);
Signature · 1 line
1.9.1
Acked-by on v2 36/63
#71 lore raw

Re: [PATCH V2 36/63] clocksource/drivers/time-orion: Convert init function to return error

drivers/clocksource/time-lpc32xx.c err_clk_enable:

Quoted 26 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/time-lpc32xx.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/clocksource/time-lpc32xx.c +0 -0
index daae61e..cb5b866 100644
@@ -288,16 +288,16 @@ err_clk_enable:

[...]

Hi Daniel,

please update the patch subject
(i.e. replace "time-orion" by "time-lpc32xx).

You can add my "Acked-by" to the V3 patch:

#72 lore raw

PATCH v2 37/63 clocksource/drivers/time-pistachio: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/time-orion.c | 52 ++++++++++++++++++++++++++++------------
 1 file changed, 37 insertions(+), 15 deletions(-)
drivers/clocksource/time-orion.c +37 -15
index 0ece742..5fdeb5d 100644
@@ -104,25 +104,36 @@ static struct irqaction orion_clkevt_irq = {
 	.handler	= orion_clkevt_irq_handler,
 };
 
-static void __init orion_timer_init(struct device_node *np)
+static int __init orion_timer_init(struct device_node *np)
 {
 	struct clk *clk;
-	int irq;
+	int irq, ret;
 
 	/* timer registers are shared with watchdog timer */
 	timer_base = of_iomap(np, 0);
-	if (!timer_base)
-		panic("%s: unable to map resource\n", np->name);
+	if (!timer_base) {
+		pr_err("%s: unable to map resource\n", np->name);
+		return -ENXIO;
+	}
 
 	clk = of_clk_get(np, 0);
-	if (IS_ERR(clk))
-		panic("%s: unable to get clk\n", np->name);
-	clk_prepare_enable(clk);
+	if (IS_ERR(clk)) {
+		pr_err("%s: unable to get clk\n", np->name);
+		return PTR_ERR(clk);
+	}
+
+	ret = clk_prepare_enable(clk);
+	if (ret) {
+		pr_err("Failed to prepare clock");
+		return ret;
+	}
 
 	/* we are only interested in timer1 irq */
 	irq = irq_of_parse_and_map(np, 1);
-	if (irq <= 0)
-		panic("%s: unable to parse timer1 irq\n", np->name);
+	if (irq <= 0) {
+		pr_err("%s: unable to parse timer1 irq\n", np->name);
+		return -EINVAL;
+	}
 
 	/* setup timer0 as free-running clocksource */
 	writel(~0, timer_base + TIMER0_VAL);
@@ -130,19 +141,30 @@ static void __init orion_timer_init(struct device_node *np)
 	atomic_io_modify(timer_base + TIMER_CTRL,
 		TIMER0_RELOAD_EN | TIMER0_EN,
 		TIMER0_RELOAD_EN | TIMER0_EN);
-	clocksource_mmio_init(timer_base + TIMER0_VAL, "orion_clocksource",
-			      clk_get_rate(clk), 300, 32,
-			      clocksource_mmio_readl_down);
+
+	ret = clocksource_mmio_init(timer_base + TIMER0_VAL, "orion_clocksource",
+				    clk_get_rate(clk), 300, 32,
+				    clocksource_mmio_readl_down);
+	if (ret) {
+		pr_err("Failed to initialize mmio timer");
+		return ret;
+	}
+
 	sched_clock_register(orion_read_sched_clock, 32, clk_get_rate(clk));
 
 	/* setup timer1 as clockevent timer */
-	if (setup_irq(irq, &orion_clkevt_irq))
-		panic("%s: unable to setup irq\n", np->name);
+	ret = setup_irq(irq, &orion_clkevt_irq);
+	if (ret) {
+		pr_err("%s: unable to setup irq\n", np->name);
+		return ret;
+	}
 
 	ticks_per_jiffy = (clk_get_rate(clk) + HZ/2) / HZ;
 	orion_clkevt.cpumask = cpumask_of(0);
 	orion_clkevt.irq = irq;
 	clockevents_config_and_register(&orion_clkevt, clk_get_rate(clk),
 					ORION_ONESHOT_MIN, ORION_ONESHOT_MAX);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(orion_timer, "marvell,orion-timer", orion_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(orion_timer, "marvell,orion-timer", orion_timer_init);
Signature · 1 line
1.9.1
#73 lore raw

PATCH v2 38/63 clocksource/drivers/time-pistachio: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/time-pistachio.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)
drivers/clocksource/time-pistachio.c +10 -10
index 376e59b..adaaec5 100644
@@ -148,7 +148,7 @@ static struct pistachio_clocksource pcs_gpt = {
 		},
 };
 
-static void __init pistachio_clksrc_of_init(struct device_node *node)
+static int __init pistachio_clksrc_of_init(struct device_node *node)
 {
 	struct clk *sys_clk, *fast_clk;
 	struct regmap *periph_regs;
@@ -158,45 +158,45 @@ static void __init pistachio_clksrc_of_init(struct device_node *node)
 	pcs_gpt.base = of_iomap(node, 0);
 	if (!pcs_gpt.base) {
 		pr_err("cannot iomap\n");
-		return;
+		return -ENXIO;
 	}
 
 	periph_regs = syscon_regmap_lookup_by_phandle(node, "img,cr-periph");
 	if (IS_ERR(periph_regs)) {
 		pr_err("cannot get peripheral regmap (%ld)\n",
 		       PTR_ERR(periph_regs));
-		return;
+		return PTR_ERR(periph_regs);
 	}
 
 	/* Switch to using the fast counter clock */
 	ret = regmap_update_bits(periph_regs, PERIP_TIMER_CONTROL,
 				 0xf, 0x0);
 	if (ret)
-		return;
+		return ret;
 
 	sys_clk = of_clk_get_by_name(node, "sys");
 	if (IS_ERR(sys_clk)) {
 		pr_err("clock get failed (%ld)\n", PTR_ERR(sys_clk));
-		return;
+		return PTR_ERR(sys_clk);
 	}
 
 	fast_clk = of_clk_get_by_name(node, "fast");
 	if (IS_ERR(fast_clk)) {
 		pr_err("clock get failed (%lu)\n", PTR_ERR(fast_clk));
-		return;
+		return PTR_ERR(fast_clk);
 	}
 
 	ret = clk_prepare_enable(sys_clk);
 	if (ret < 0) {
 		pr_err("failed to enable clock (%d)\n", ret);
-		return;
+		return ret;
 	}
 
 	ret = clk_prepare_enable(fast_clk);
 	if (ret < 0) {
 		pr_err("failed to enable clock (%d)\n", ret);
 		clk_disable_unprepare(sys_clk);
-		return;
+		return ret;
 	}
 
 	rate = clk_get_rate(fast_clk);
@@ -212,7 +212,7 @@ static void __init pistachio_clksrc_of_init(struct device_node *node)
 
 	raw_spin_lock_init(&pcs_gpt.lock);
 	sched_clock_register(pistachio_read_sched_clock, 32, rate);
-	clocksource_register_hz(&pcs_gpt.cs, rate);
+	return clocksource_register_hz(&pcs_gpt.cs, rate);
 }
-CLOCKSOURCE_OF_DECLARE(pistachio_gptimer, "img,pistachio-gptimer",
+CLOCKSOURCE_OF_DECLARE_RET(pistachio_gptimer, "img,pistachio-gptimer",
 		       pistachio_clksrc_of_init);
Signature · 1 line
1.9.1
#74 lore raw

PATCH v2 39/63 clocksource/drivers/timer-atlas7: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-atlas7.c | 32 +++++++++++++++++++-------------
 1 file changed, 19 insertions(+), 13 deletions(-)
drivers/clocksource/timer-atlas7.c +19 -13
index 27fa136..7b1a007 100644
@@ -238,7 +238,7 @@ static struct notifier_block sirfsoc_cpu_nb = {
 	.notifier_call = sirfsoc_cpu_notify,
 };
 
-static void __init sirfsoc_clockevent_init(void)
+static int __init sirfsoc_clockevent_init(void)
 {
 	sirfsoc_clockevent = alloc_percpu(struct clock_event_device);
 	BUG_ON(!sirfsoc_clockevent);
@@ -246,11 +246,11 @@ static void __init sirfsoc_clockevent_init(void)
 	BUG_ON(register_cpu_notifier(&sirfsoc_cpu_nb));
 
 	/* Immediately configure the timer on the boot CPU */
-	sirfsoc_local_timer_setup(this_cpu_ptr(sirfsoc_clockevent));
+	return sirfsoc_local_timer_setup(this_cpu_ptr(sirfsoc_clockevent));
 }
 
 /* initialize the kernel jiffy timer source */
-static void __init sirfsoc_atlas7_timer_init(struct device_node *np)
+static int __init sirfsoc_atlas7_timer_init(struct device_node *np)
 {
 	struct clk *clk;
 
@@ -279,23 +279,29 @@ static void __init sirfsoc_atlas7_timer_init(struct device_node *np)
 
 	BUG_ON(clocksource_register_hz(&sirfsoc_clocksource, atlas7_timer_rate));
 
-	sirfsoc_clockevent_init();
+	return sirfsoc_clockevent_init();
 }
 
-static void __init sirfsoc_of_timer_init(struct device_node *np)
+static int __init sirfsoc_of_timer_init(struct device_node *np)
 {
 	sirfsoc_timer_base = of_iomap(np, 0);
-	if (!sirfsoc_timer_base)
-		panic("unable to map timer cpu registers\n");
+	if (!sirfsoc_timer_base) {
+		pr_err("unable to map timer cpu registers\n");
+		return -ENXIO;
+	}
 
 	sirfsoc_timer_irq.irq = irq_of_parse_and_map(np, 0);
-	if (!sirfsoc_timer_irq.irq)
-		panic("No irq passed for timer0 via DT\n");
+	if (!sirfsoc_timer_irq.irq) {
+		pr_err("No irq passed for timer0 via DT\n");
+		return -EINVAL;
+	}
 
 	sirfsoc_timer1_irq.irq = irq_of_parse_and_map(np, 1);
-	if (!sirfsoc_timer1_irq.irq)
-		panic("No irq passed for timer1 via DT\n");
+	if (!sirfsoc_timer1_irq.irq) {
+		pr_err("No irq passed for timer1 via DT\n");
+		return -EINVAL;
+	}
 
-	sirfsoc_atlas7_timer_init(np);
+	return sirfsoc_atlas7_timer_init(np);
 }
-CLOCKSOURCE_OF_DECLARE(sirfsoc_atlas7_timer, "sirf,atlas7-tick", sirfsoc_of_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(sirfsoc_atlas7_timer, "sirf,atlas7-tick", sirfsoc_of_timer_init);
Signature · 1 line
1.9.1
#75 lore raw

PATCH v2 40/63 clocksource/drivers/timer-atmel-pit: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-atmel-pit.c | 43 +++++++++++++++++++++++------------
 1 file changed, 29 insertions(+), 14 deletions(-)
drivers/clocksource/timer-atmel-pit.c +29 -14
index d911c5d..ffaca7c 100644
@@ -177,7 +177,7 @@ static irqreturn_t at91sam926x_pit_interrupt(int irq, void *dev_id)
 /*
  * Set up both clocksource and clockevent support.
  */
-static void __init at91sam926x_pit_common_init(struct pit_data *data)
+static int __init at91sam926x_pit_common_init(struct pit_data *data)
 {
 	unsigned long	pit_rate;
 	unsigned	bits;
@@ -204,14 +204,21 @@ static void __init at91sam926x_pit_common_init(struct pit_data *data)
 	data->clksrc.rating = 175;
 	data->clksrc.read = read_pit_clk;
 	data->clksrc.flags = CLOCK_SOURCE_IS_CONTINUOUS;
-	clocksource_register_hz(&data->clksrc, pit_rate);
+	
+	ret = clocksource_register_hz(&data->clksrc, pit_rate);
+	if (ret) {
+		pr_err("Failed to register clocksource");
+		return ret;
+	}
 
 	/* Set up irq handler */
 	ret = request_irq(data->irq, at91sam926x_pit_interrupt,
 			  IRQF_SHARED | IRQF_TIMER | IRQF_IRQPOLL,
 			  "at91_tick", data);
-	if (ret)
-		panic(pr_fmt("Unable to setup IRQ\n"));
+	if (ret) {
+		pr_err("Unable to setup IRQ\n");
+		return ret;
+	}
 
 	/* Set up and register clockevents */
 	data->clkevt.name = "pit";
@@ -226,34 +233,42 @@ static void __init at91sam926x_pit_common_init(struct pit_data *data)
 	data->clkevt.resume = at91sam926x_pit_resume;
 	data->clkevt.suspend = at91sam926x_pit_suspend;
 	clockevents_register_device(&data->clkevt);
+
+	return 0;
 }
 
-static void __init at91sam926x_pit_dt_init(struct device_node *node)
+static int __init at91sam926x_pit_dt_init(struct device_node *node)
 {
 	struct pit_data *data;
 
 	data = kzalloc(sizeof(*data), GFP_KERNEL);
 	if (!data)
-		panic(pr_fmt("Unable to allocate memory\n"));
+		return -ENOMEM;
 
 	data->base = of_iomap(node, 0);
-	if (!data->base)
-		panic(pr_fmt("Could not map PIT address\n"));
+	if (!data->base) {
+		pr_err("Could not map PIT address\n");
+		return -ENXIO;
+	}
 
 	data->mck = of_clk_get(node, 0);
 	if (IS_ERR(data->mck))
 		/* Fallback on clkdev for !CCF-based boards */
 		data->mck = clk_get(NULL, "mck");
 
-	if (IS_ERR(data->mck))
-		panic(pr_fmt("Unable to get mck clk\n"));
+	if (IS_ERR(data->mck)) {
+		pr_err("Unable to get mck clk\n");
+		return PTR_ERR(data->mck);
+	}
 
 	/* Get the interrupts property */
 	data->irq = irq_of_parse_and_map(node, 0);
-	if (!data->irq)
-		panic(pr_fmt("Unable to get IRQ from DT\n"));
+	if (!data->irq) {
+		pr_err("Unable to get IRQ from DT\n");
+		return -EINVAL;
+	}
 
-	at91sam926x_pit_common_init(data);
+	return at91sam926x_pit_common_init(data);
 }
-CLOCKSOURCE_OF_DECLARE(at91sam926x_pit, "atmel,at91sam9260-pit",
+CLOCKSOURCE_OF_DECLARE_RET(at91sam926x_pit, "atmel,at91sam9260-pit",
 		       at91sam926x_pit_dt_init);
Signature · 1 line
1.9.1
#76 lore raw

PATCH v2 41/63 clocksource/drivers/timer-atmel-st: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-atmel-st.c | 44 +++++++++++++++++++++++-------------
 1 file changed, 28 insertions(+), 16 deletions(-)
drivers/clocksource/timer-atmel-st.c +28 -16
index 29d21d6..e9331d3 100644
@@ -194,15 +194,17 @@ static struct clock_event_device clkevt = {
 /*
  * ST (system timer) module supports both clockevents and clocksource.
  */
-static void __init atmel_st_timer_init(struct device_node *node)
+static int __init atmel_st_timer_init(struct device_node *node)
 {
 	struct clk *sclk;
 	unsigned int sclk_rate, val;
 	int irq, ret;
 
 	regmap_st = syscon_node_to_regmap(node);
-	if (IS_ERR(regmap_st))
-		panic(pr_fmt("Unable to get regmap\n"));
+	if (IS_ERR(regmap_st)) {
+		pr_err("Unable to get regmap\n");
+		return PTR_ERR(regmap_st);
+	}
 
 	/* Disable all timer interrupts, and clear any pending ones */
 	regmap_write(regmap_st, AT91_ST_IDR,
@@ -211,27 +213,37 @@ static void __init atmel_st_timer_init(struct device_node *node)
 
 	/* Get the interrupts property */
 	irq  = irq_of_parse_and_map(node, 0);
-	if (!irq)
-		panic(pr_fmt("Unable to get IRQ from DT\n"));
+	if (!irq) {
+		pr_err("Unable to get IRQ from DT\n");
+		return -EINVAL;
+	}
 
 	/* Make IRQs happen for the system timer */
 	ret = request_irq(irq, at91rm9200_timer_interrupt,
 			  IRQF_SHARED | IRQF_TIMER | IRQF_IRQPOLL,
 			  "at91_tick", regmap_st);
-	if (ret)
-		panic(pr_fmt("Unable to setup IRQ\n"));
+	if (ret) {
+		pr_err("Unable to setup IRQ\n");
+		return ret;
+	}
 
 	sclk = of_clk_get(node, 0);
-	if (IS_ERR(sclk))
-		panic(pr_fmt("Unable to get slow clock\n"));
+	if (IS_ERR(sclk)) {
+		pr_err("Unable to get slow clock\n");
+		return PTR_ERR(sclk);
+	}
 
-	clk_prepare_enable(sclk);
-	if (ret)
-		panic(pr_fmt("Could not enable slow clock\n"));
+	ret = clk_prepare_enable(sclk);
+	if (ret) {
+		pr_err("Could not enable slow clock\n");
+		return ret;
+	}
 
 	sclk_rate = clk_get_rate(sclk);
-	if (!sclk_rate)
-		panic(pr_fmt("Invalid slow clock rate\n"));
+	if (!sclk_rate) {
+		pr_err("Invalid slow clock rate\n");
+		return -EINVAL;
+	}
 	timer_latch = (sclk_rate + HZ / 2) / HZ;
 
 	/* The 32KiHz "Slow Clock" (tick every 30517.58 nanoseconds) is used
@@ -246,7 +258,7 @@ static void __init atmel_st_timer_init(struct device_node *node)
 					2, AT91_ST_ALMV);
 
 	/* register clocksource */
-	clocksource_register_hz(&clk32k, sclk_rate);
+	return clocksource_register_hz(&clk32k, sclk_rate);
 }
-CLOCKSOURCE_OF_DECLARE(atmel_st_timer, "atmel,at91rm9200-st",
+CLOCKSOURCE_OF_DECLARE_RET(atmel_st_timer, "atmel,at91rm9200-st",
 		       atmel_st_timer_init);
Signature · 1 line
1.9.1
#77 lore raw

PATCH v2 42/63 clocksource/drivers/prima2: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-prima2.c | 43 ++++++++++++++++++++++++++++----------
 1 file changed, 32 insertions(+), 11 deletions(-)
drivers/clocksource/timer-prima2.c +32 -11
index 2854c66..7b1084d 100644
@@ -189,24 +189,36 @@ static void __init sirfsoc_clockevent_init(void)
 }
 
 /* initialize the kernel jiffy timer source */
-static void __init sirfsoc_prima2_timer_init(struct device_node *np)
+static int __init sirfsoc_prima2_timer_init(struct device_node *np)
 {
 	unsigned long rate;
 	struct clk *clk;
+	int ret;
 
 	clk = of_clk_get(np, 0);
-	BUG_ON(IS_ERR(clk));
+	if (IS_ERR(clk)) {
+		pr_err("Failed to get clock");
+		return PTR_ERR(clk);
+	}
 
-	BUG_ON(clk_prepare_enable(clk));
+	ret = clk_prepare_enable(clk);
+	if (ret) {
+		pr_err("Failed to enable clock");
+		return ret;
+	}
 
 	rate = clk_get_rate(clk);
 
-	BUG_ON(rate < PRIMA2_CLOCK_FREQ);
-	BUG_ON(rate % PRIMA2_CLOCK_FREQ);
+	if (rate < PRIMA2_CLOCK_FREQ || rate % PRIMA2_CLOCK_FREQ) {
+		pr_err("Invalid clock rate");
+		return -EINVAL;
+	}
 
 	sirfsoc_timer_base = of_iomap(np, 0);
-	if (!sirfsoc_timer_base)
-		panic("unable to map timer cpu registers\n");
+	if (!sirfsoc_timer_base) {
+		pr_err("unable to map timer cpu registers\n");
+		return -ENXIO;
+	}
 
 	sirfsoc_timer_irq.irq = irq_of_parse_and_map(np, 0);
 
@@ -216,14 +228,23 @@ static void __init sirfsoc_prima2_timer_init(struct device_node *np)
 	writel_relaxed(0, sirfsoc_timer_base + SIRFSOC_TIMER_COUNTER_HI);
 	writel_relaxed(BIT(0), sirfsoc_timer_base + SIRFSOC_TIMER_STATUS);
 
-	BUG_ON(clocksource_register_hz(&sirfsoc_clocksource,
-				       PRIMA2_CLOCK_FREQ));
+	ret = clocksource_register_hz(&sirfsoc_clocksource, PRIMA2_CLOCK_FREQ);
+	if (ret) {
+		pr_err("Failed to register clocksource");
+		return ret;
+	}
 
 	sched_clock_register(sirfsoc_read_sched_clock, 64, PRIMA2_CLOCK_FREQ);
 
-	BUG_ON(setup_irq(sirfsoc_timer_irq.irq, &sirfsoc_timer_irq));
+	ret = setup_irq(sirfsoc_timer_irq.irq, &sirfsoc_timer_irq);
+	if (ret) {
+		pr_err("Failed to setup irq");
+		return ret;
+	}
 
 	sirfsoc_clockevent_init();
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(sirfsoc_prima2_timer,
+CLOCKSOURCE_OF_DECLARE_RET(sirfsoc_prima2_timer,
 	"sirf,prima2-tick", sirfsoc_prima2_timer_init);
Signature · 1 line
1.9.1
#78 lore raw

PATCH v2 43/63 clocksource/drivers/timer-imx-gpt: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-imx-gpt.c | 75 ++++++++++++++++++++++---------------
 1 file changed, 45 insertions(+), 30 deletions(-)
drivers/clocksource/timer-imx-gpt.c +45 -30
index 99ec967..d5640a74 100644
@@ -407,8 +407,10 @@ static const struct imx_gpt_data imx6dl_gpt_data = {
 	.set_next_event = v2_set_next_event,
 };
 
-static void __init _mxc_timer_init(struct imx_timer *imxtm)
+static int __init _mxc_timer_init(struct imx_timer *imxtm)
 {
+	int ret;
+
 	switch (imxtm->type) {
 	case GPT_TYPE_IMX1:
 		imxtm->gpt = &imx1_gpt_data;
@@ -423,12 +425,12 @@ static void __init _mxc_timer_init(struct imx_timer *imxtm)
 		imxtm->gpt = &imx6dl_gpt_data;
 		break;
 	default:
-		BUG();
+		return -EINVAL;
 	}
 
 	if (IS_ERR(imxtm->clk_per)) {
 		pr_err("i.MX timer: unable to get clk\n");
-		return;
+		return PTR_ERR(imxtm->clk_per);
 	}
 
 	if (!IS_ERR(imxtm->clk_ipg))
@@ -446,8 +448,11 @@ static void __init _mxc_timer_init(struct imx_timer *imxtm)
 	imxtm->gpt->gpt_setup_tctl(imxtm);
 
 	/* init and register the timer to the framework */
-	mxc_clocksource_init(imxtm);
-	mxc_clockevent_init(imxtm);
+	ret = mxc_clocksource_init(imxtm);
+	if (ret)
+		return ret;
+
+	return mxc_clockevent_init(imxtm);
 }
 
 void __init mxc_timer_init(unsigned long pbase, int irq, enum imx_gpt_type type)
@@ -469,21 +474,27 @@ void __init mxc_timer_init(unsigned long pbase, int irq, enum imx_gpt_type type)
 	_mxc_timer_init(imxtm);
 }
 
-static void __init mxc_timer_init_dt(struct device_node *np,  enum imx_gpt_type type)
+static int __init mxc_timer_init_dt(struct device_node *np,  enum imx_gpt_type type)
 {
 	struct imx_timer *imxtm;
 	static int initialized;
+	int ret;
 
 	/* Support one instance only */
 	if (initialized)
-		return;
+		return 0;
 
 	imxtm = kzalloc(sizeof(*imxtm), GFP_KERNEL);
-	BUG_ON(!imxtm);
+	if (!imxtm)
+		return -ENOMEM;
 
 	imxtm->base = of_iomap(np, 0);
-	WARN_ON(!imxtm->base);
+	if (!imxtm->base)
+		return -ENXIO;
+
 	imxtm->irq = irq_of_parse_and_map(np, 0);
+	if (imxtm->irq <= 0)
+		return -EINVAL;
 
 	imxtm->clk_ipg = of_clk_get_by_name(np, "ipg");
 
@@ -494,22 +505,26 @@ static void __init mxc_timer_init_dt(struct device_node *np,  enum imx_gpt_type
 
 	imxtm->type = type;
 
-	_mxc_timer_init(imxtm);
+	ret = _mxc_timer_init(imxtm);
+	if (ret)
+		return ret;
 
 	initialized = 1;
+
+	return 0;
 }
 
-static void __init imx1_timer_init_dt(struct device_node *np)
+static int __init imx1_timer_init_dt(struct device_node *np)
 {
-	mxc_timer_init_dt(np, GPT_TYPE_IMX1);
+	return mxc_timer_init_dt(np, GPT_TYPE_IMX1);
 }
 
-static void __init imx21_timer_init_dt(struct device_node *np)
+static int __init imx21_timer_init_dt(struct device_node *np)
 {
-	mxc_timer_init_dt(np, GPT_TYPE_IMX21);
+	return mxc_timer_init_dt(np, GPT_TYPE_IMX21);
 }
 
-static void __init imx31_timer_init_dt(struct device_node *np)
+static int __init imx31_timer_init_dt(struct device_node *np)
 {
 	enum imx_gpt_type type = GPT_TYPE_IMX31;
 
@@ -522,23 +537,23 @@ static void __init imx31_timer_init_dt(struct device_node *np)
 	if (of_machine_is_compatible("fsl,imx6dl"))
 		type = GPT_TYPE_IMX6DL;
 
-	mxc_timer_init_dt(np, type);
+	return mxc_timer_init_dt(np, type);
 }
 
-static void __init imx6dl_timer_init_dt(struct device_node *np)
+static int __init imx6dl_timer_init_dt(struct device_node *np)
 {
-	mxc_timer_init_dt(np, GPT_TYPE_IMX6DL);
+	return mxc_timer_init_dt(np, GPT_TYPE_IMX6DL);
 }
 
-CLOCKSOURCE_OF_DECLARE(imx1_timer, "fsl,imx1-gpt", imx1_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx21_timer, "fsl,imx21-gpt", imx21_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx27_timer, "fsl,imx27-gpt", imx21_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx31_timer, "fsl,imx31-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx25_timer, "fsl,imx25-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx50_timer, "fsl,imx50-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx51_timer, "fsl,imx51-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx53_timer, "fsl,imx53-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx6q_timer, "fsl,imx6q-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx6dl_timer, "fsl,imx6dl-gpt", imx6dl_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx6sl_timer, "fsl,imx6sl-gpt", imx6dl_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx1_timer, "fsl,imx1-gpt", imx1_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx21_timer, "fsl,imx21-gpt", imx21_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx27_timer, "fsl,imx27-gpt", imx21_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx31_timer, "fsl,imx31-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx25_timer, "fsl,imx25-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx50_timer, "fsl,imx50-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx51_timer, "fsl,imx51-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx53_timer, "fsl,imx53-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx6q_timer, "fsl,imx6q-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx6dl_timer, "fsl,imx6dl-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx6sl_timer, "fsl,imx6sl-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE_RET(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
Signature · 1 line
1.9.1
#79 lore raw

PATCH v2 44/63 clocksource/drivers/timer-integrator-ap: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-integrator-ap.c | 59 ++++++++++++++++++++-----------
 1 file changed, 38 insertions(+), 21 deletions(-)
drivers/clocksource/timer-integrator-ap.c +38 -21
index 3f59ac2..675face 100644
@@ -36,11 +36,12 @@ static u64 notrace integrator_read_sched_clock(void)
 	return -readl(sched_clk_base + TIMER_VALUE);
 }
 
-static void integrator_clocksource_init(unsigned long inrate,
-					void __iomem *base)
+static int integrator_clocksource_init(unsigned long inrate,
+				       void __iomem *base)
 {
 	u32 ctrl = TIMER_CTRL_ENABLE | TIMER_CTRL_PERIODIC;
 	unsigned long rate = inrate;
+	int ret;
 
 	if (rate >= 1500000) {
 		rate /= 16;
@@ -50,11 +51,15 @@ static void integrator_clocksource_init(unsigned long inrate,
 	writel(0xffff, base + TIMER_LOAD);
 	writel(ctrl, base + TIMER_CTRL);
 
-	clocksource_mmio_init(base + TIMER_VALUE, "timer2",
-			rate, 200, 16, clocksource_mmio_readl_down);
+	ret = clocksource_mmio_init(base + TIMER_VALUE, "timer2",
+				    rate, 200, 16, clocksource_mmio_readl_down);
+	if (ret)
+		return ret;
 
 	sched_clk_base = base;
 	sched_clock_register(integrator_read_sched_clock, 16, rate);
+
+	return 0;
 }
 
 static unsigned long timer_reload;
@@ -138,11 +143,12 @@ static struct irqaction integrator_timer_irq = {
 	.dev_id		= &integrator_clockevent,
 };
 
-static void integrator_clockevent_init(unsigned long inrate,
-				void __iomem *base, int irq)
+static int integrator_clockevent_init(unsigned long inrate,
+				      void __iomem *base, int irq)
 {
 	unsigned long rate = inrate;
 	unsigned int ctrl = 0;
+	int ret;
 
 	clkevt_base = base;
 	/* Calculate and program a divisor */
@@ -156,14 +162,18 @@ static void integrator_clockevent_init(unsigned long inrate,
 	timer_reload = rate / HZ;
 	writel(ctrl, clkevt_base + TIMER_CTRL);
 
-	setup_irq(irq, &integrator_timer_irq);
+	ret = setup_irq(irq, &integrator_timer_irq);
+	if (ret)
+		return ret;
+
 	clockevents_config_and_register(&integrator_clockevent,
 					rate,
 					1,
 					0xffffU);
+	return 0;
 }
 
-static void __init integrator_ap_timer_init_of(struct device_node *node)
+static int __init integrator_ap_timer_init_of(struct device_node *node)
 {
 	const char *path;
 	void __iomem *base;
@@ -176,12 +186,12 @@ static void __init integrator_ap_timer_init_of(struct device_node *node)
 
 	base = of_io_request_and_map(node, 0, "integrator-timer");
 	if (IS_ERR(base))
-		return;
+		return PTR_ERR(base);
 
 	clk = of_clk_get(node, 0);
 	if (IS_ERR(clk)) {
 		pr_err("No clock for %s\n", node->name);
-		return;
+		return PTR_ERR(clk);
 	}
 	clk_prepare_enable(clk);
 	rate = clk_get_rate(clk);
@@ -189,31 +199,38 @@ static void __init integrator_ap_timer_init_of(struct device_node *node)
 
 	err = of_property_read_string(of_aliases,
 				"arm,timer-primary", &path);
-	if (WARN_ON(err))
-		return;
+	if (err) {
+		pr_warn("Failed to read property");
+		return err;
+	}
+
 	pri_node = of_find_node_by_path(path);
+
 	err = of_property_read_string(of_aliases,
 				"arm,timer-secondary", &path);
-	if (WARN_ON(err))
-		return;
+	if (err) {
+		pr_warn("Failed to read property");		
+		return err;
+	}
+
+
 	sec_node = of_find_node_by_path(path);
 
-	if (node == pri_node) {
+	if (node == pri_node)
 		/* The primary timer lacks IRQ, use as clocksource */
-		integrator_clocksource_init(rate, base);
-		return;
-	}
+		return integrator_clocksource_init(rate, base);
 
 	if (node == sec_node) {
 		/* The secondary timer will drive the clock event */
 		irq = irq_of_parse_and_map(node, 0);
-		integrator_clockevent_init(rate, base, irq);
-		return;
+		return integrator_clockevent_init(rate, base, irq);
 	}
 
 	pr_info("Timer @%p unused\n", base);
 	clk_disable_unprepare(clk);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(integrator_ap_timer, "arm,integrator-timer",
+CLOCKSOURCE_OF_DECLARE_RET(integrator_ap_timer, "arm,integrator-timer",
 		       integrator_ap_timer_init_of);
Signature · 1 line
1.9.1
#80 lore raw

PATCH v2 45/63 clocksource/drivers/timer-keystone: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-keystone.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)
drivers/clocksource/timer-keystone.c +8 -7
index 1cea08c..4199823 100644
@@ -144,7 +144,7 @@ static int keystone_set_periodic(struct clock_event_device *evt)
 	return 0;
 }
 
-static void __init keystone_timer_init(struct device_node *np)
+static int __init keystone_timer_init(struct device_node *np)
 {
 	struct clock_event_device *event_dev = &timer.event_dev;
 	unsigned long rate;
@@ -154,20 +154,20 @@ static void __init keystone_timer_init(struct device_node *np)
 	irq  = irq_of_parse_and_map(np, 0);
 	if (!irq) {
 		pr_err("%s: failed to map interrupts\n", __func__);
-		return;
+		return -EINVAL;
 	}
 
 	timer.base = of_iomap(np, 0);
 	if (!timer.base) {
 		pr_err("%s: failed to map registers\n", __func__);
-		return;
+		return -ENXIO;
 	}
 
 	clk = of_clk_get(np, 0);
 	if (IS_ERR(clk)) {
 		pr_err("%s: failed to get clock\n", __func__);
 		iounmap(timer.base);
-		return;
+		return PTR_ERR(clk);
 	}
 
 	error = clk_prepare_enable(clk);
@@ -219,11 +219,12 @@ static void __init keystone_timer_init(struct device_node *np)
 	clockevents_config_and_register(event_dev, rate, 1, ULONG_MAX);
 
 	pr_info("keystone timer clock @%lu Hz\n", rate);
-	return;
+	return 0;
 err:
 	clk_put(clk);
 	iounmap(timer.base);
+	return error;
 }
 
-CLOCKSOURCE_OF_DECLARE(keystone_timer, "ti,keystone-timer",
-					keystone_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(keystone_timer, "ti,keystone-timer",
+			   keystone_timer_init);
Signature · 1 line
1.9.1
Acked-by on v2 45/63
#81 lore raw

Re: [PATCH V2 45/63] clocksource/drivers/timer-keystone: Convert init function to return error

Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 9 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-keystone.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)
#82 lore raw

PATCH v2 46/63 clocksource/drivers/timer-sp804: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-sp804.c | 91 ++++++++++++++++++++++++++-------------
 1 file changed, 60 insertions(+), 31 deletions(-)
drivers/clocksource/timer-sp804.c +60 -31
index 5f45b9a..7c2944ad 100644
@@ -77,7 +77,7 @@ void __init sp804_timer_disable(void __iomem *base)
 	writel(0, base + TIMER_CTRL);
 }
 
-void __init __sp804_clocksource_and_sched_clock_init(void __iomem *base,
+int  __init __sp804_clocksource_and_sched_clock_init(void __iomem *base,
 						     const char *name,
 						     struct clk *clk,
 						     int use_sched_clock)
@@ -89,14 +89,13 @@ void __init __sp804_clocksource_and_sched_clock_init(void __iomem *base,
 		if (IS_ERR(clk)) {
 			pr_err("sp804: clock not found: %d\n",
 			       (int)PTR_ERR(clk));
-			return;
+			return PTR_ERR(clk);
 		}
 	}
 
 	rate = sp804_get_clock_rate(clk);
-
 	if (rate < 0)
-		return;
+		return -EINVAL;
 
 	/* setup timer 0 as free-running clocksource */
 	writel(0, base + TIMER_CTRL);
@@ -112,6 +111,8 @@ void __init __sp804_clocksource_and_sched_clock_init(void __iomem *base,
 		sched_clock_base = base;
 		sched_clock_register(sp804_read, 32, rate);
 	}
+
+	return 0;
 }
 
 
@@ -186,7 +187,7 @@ static struct irqaction sp804_timer_irq = {
 	.dev_id		= &sp804_clockevent,
 };
 
-void __init __sp804_clockevents_init(void __iomem *base, unsigned int irq, struct clk *clk, const char *name)
+int __init __sp804_clockevents_init(void __iomem *base, unsigned int irq, struct clk *clk, const char *name)
 {
 	struct clock_event_device *evt = &sp804_clockevent;
 	long rate;
@@ -196,12 +197,12 @@ void __init __sp804_clockevents_init(void __iomem *base, unsigned int irq, struc
 	if (IS_ERR(clk)) {
 		pr_err("sp804: %s clock not found: %d\n", name,
 			(int)PTR_ERR(clk));
-		return;
+		return PTR_ERR(clk);
 	}
 
 	rate = sp804_get_clock_rate(clk);
 	if (rate < 0)
-		return;
+		return -EINVAL;
 
 	clkevt_base = base;
 	clkevt_reload = DIV_ROUND_CLOSEST(rate, HZ);
@@ -213,27 +214,31 @@ void __init __sp804_clockevents_init(void __iomem *base, unsigned int irq, struc
 
 	setup_irq(irq, &sp804_timer_irq);
 	clockevents_config_and_register(evt, rate, 0xf, 0xffffffff);
+
+	return 0;
 }
 
-static void __init sp804_of_init(struct device_node *np)
+static int __init sp804_of_init(struct device_node *np)
 {
 	static bool initialized = false;
 	void __iomem *base;
-	int irq;
+	int irq, ret = -EINVAL;
 	u32 irq_num = 0;
 	struct clk *clk1, *clk2;
 	const char *name = of_get_property(np, "compatible", NULL);
 
 	base = of_iomap(np, 0);
-	if (WARN_ON(!base))
-		return;
+	if (!base)
+		return -ENXIO;
 
 	/* Ensure timers are disabled */
 	writel(0, base + TIMER_CTRL);
 	writel(0, base + TIMER_2_BASE + TIMER_CTRL);
 
-	if (initialized || !of_device_is_available(np))
+	if (initialized || !of_device_is_available(np)) {
+		ret = -EINVAL;
 		goto err;
+	}
 
 	clk1 = of_clk_get(np, 0);
 	if (IS_ERR(clk1))
@@ -256,35 +261,53 @@ static void __init sp804_of_init(struct device_node *np)
 
 	of_property_read_u32(np, "arm,sp804-has-irq", &irq_num);
 	if (irq_num == 2) {
-		__sp804_clockevents_init(base + TIMER_2_BASE, irq, clk2, name);
-		__sp804_clocksource_and_sched_clock_init(base, name, clk1, 1);
+
+		ret = __sp804_clockevents_init(base + TIMER_2_BASE, irq, clk2, name);
+		if (ret)
+			goto err;
+
+		ret = __sp804_clocksource_and_sched_clock_init(base, name, clk1, 1);
+		if (ret)
+			goto err;
 	} else {
-		__sp804_clockevents_init(base, irq, clk1 , name);
-		__sp804_clocksource_and_sched_clock_init(base + TIMER_2_BASE,
-							 name, clk2, 1);
+
+		ret = __sp804_clockevents_init(base, irq, clk1 , name);
+		if (ret)
+			goto err;
+
+		ret =__sp804_clocksource_and_sched_clock_init(base + TIMER_2_BASE,
+							      name, clk2, 1);
+		if (ret)
+			goto err;
 	}
 	initialized = true;
 
-	return;
+	return 0;
 err:
 	iounmap(base);
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(sp804, "arm,sp804", sp804_of_init);
+CLOCKSOURCE_OF_DECLARE_RET(sp804, "arm,sp804", sp804_of_init);
 
-static void __init integrator_cp_of_init(struct device_node *np)
+static int __init integrator_cp_of_init(struct device_node *np)
 {
 	static int init_count = 0;
 	void __iomem *base;
-	int irq;
+	int irq, ret = -EINVAL;
 	const char *name = of_get_property(np, "compatible", NULL);
 	struct clk *clk;
 
 	base = of_iomap(np, 0);
-	if (WARN_ON(!base))
-		return;
+	if (!base) {
+		pr_err("Failed to iomap");
+		return -ENXIO;
+	}
+
 	clk = of_clk_get(np, 0);
-	if (WARN_ON(IS_ERR(clk)))
-		return;
+	if (IS_ERR(clk)) {
+		pr_err("Failed to get clock");
+		return PTR_ERR(clk);
+	}
 
 	/* Ensure timer is disabled */
 	writel(0, base + TIMER_CTRL);
@@ -292,19 +315,25 @@ static void __init integrator_cp_of_init(struct device_node *np)
 	if (init_count == 2 || !of_device_is_available(np))
 		goto err;
 
-	if (!init_count)
-		__sp804_clocksource_and_sched_clock_init(base, name, clk, 0);
-	else {
+	if (!init_count) {
+		ret = __sp804_clocksource_and_sched_clock_init(base, name, clk, 0);
+		if (ret)
+			goto err;
+			
+	} else {
 		irq = irq_of_parse_and_map(np, 0);
 		if (irq <= 0)
 			goto err;
 
-		__sp804_clockevents_init(base, irq, clk, name);
+		ret = __sp804_clockevents_init(base, irq, clk, name);
+		if (ret)
+			goto err;
 	}
 
 	init_count++;
-	return;
+	return 0;
 err:
 	iounmap(base);
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(intcp, "arm,integrator-cp-timer", integrator_cp_of_init);
+CLOCKSOURCE_OF_DECLARE_RET(intcp, "arm,integrator-cp-timer", integrator_cp_of_init);
Signature · 1 line
1.9.1
#83 lore raw

PATCH v2 47/63 clocksource/drivers/timer-stm32: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-stm32.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/clocksource/timer-stm32.c +6 -4
index f3dcb76..d5bf352 100644
@@ -98,7 +98,7 @@ static struct stm32_clock_event_ddata clock_event_ddata = {
 	},
 };
 
-static void __init stm32_clockevent_init(struct device_node *np)
+static int __init stm32_clockevent_init(struct device_node *np)
 {
 	struct stm32_clock_event_ddata *data = &clock_event_ddata;
 	struct clk *clk;
@@ -130,12 +130,14 @@ static void __init stm32_clockevent_init(struct device_node *np)
 
 	data->base = of_iomap(np, 0);
 	if (!data->base) {
+		ret = -ENXIO;
 		pr_err("failed to map registers for clockevent\n");
 		goto err_iomap;
 	}
 
 	irq = irq_of_parse_and_map(np, 0);
 	if (!irq) {
+		ret = -EINVAL;
 		pr_err("%s: failed to get irq.\n", np->full_name);
 		goto err_get_irq;
 	}
@@ -173,7 +175,7 @@ static void __init stm32_clockevent_init(struct device_node *np)
 	pr_info("%s: STM32 clockevent driver initialized (%d bits)\n",
 			np->full_name, bits);
 
-	return;
+	return ret;
 
 err_get_irq:
 	iounmap(data->base);
@@ -182,7 +184,7 @@ err_iomap:
 err_clk_enable:
 	clk_put(clk);
 err_clk_get:
-	return;
+	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE(stm32, "st,stm32-timer", stm32_clockevent_init);
+CLOCKSOURCE_OF_DECLARE_RET(stm32, "st,stm32-timer", stm32_clockevent_init);
Signature · 1 line
1.9.1
maintainer Acked-by on v2 47/63
#84 lore raw

Re: [PATCH V2 47/63] clocksource/drivers/timer-stm32: Convert init function to return error

2016-06-16 23:27 GMT+02:00 Daniel Lezcano <[email protected]>:

Quoted 12 lines

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 8 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-stm32.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

Thanks!
Maxime

#85 lore raw

PATCH v2 48/63 clocksource/drivers/timer-sun5i: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-sun5i.c | 37 +++++++++++++++++++++++--------------
 1 file changed, 23 insertions(+), 14 deletions(-)
drivers/clocksource/timer-sun5i.c +23 -14
index 24c83f9..f0a3ffb 100644
@@ -311,33 +311,42 @@ err_free:
 	return ret;
 }
 
-static void __init sun5i_timer_init(struct device_node *node)
+static int __init sun5i_timer_init(struct device_node *node)
 {
 	struct reset_control *rstc;
 	void __iomem *timer_base;
 	struct clk *clk;
-	int irq;
+	int irq, ret;
 
 	timer_base = of_io_request_and_map(node, 0, of_node_full_name(node));
-	if (IS_ERR(timer_base))
-		panic("Can't map registers");
+	if (IS_ERR(timer_base)) {
+		pr_err("Can't map registers");
+		return PTR_ERR(timer_base);;
+	}
 
 	irq = irq_of_parse_and_map(node, 0);
-	if (irq <= 0)
-		panic("Can't parse IRQ");
+	if (irq <= 0) {
+		pr_err("Can't parse IRQ");
+		return -EINVAL;
+	}
 
 	clk = of_clk_get(node, 0);
-	if (IS_ERR(clk))
-		panic("Can't get timer clock");
+	if (IS_ERR(clk)) {
+		pr_err("Can't get timer clock");
+		return PTR_ERR(clk);
+	}
 
 	rstc = of_reset_control_get(node, NULL);
 	if (!IS_ERR(rstc))
 		reset_control_deassert(rstc);
 
-	sun5i_setup_clocksource(node, timer_base, clk, irq);
-	sun5i_setup_clockevent(node, timer_base, clk, irq);
+	ret = sun5i_setup_clocksource(node, timer_base, clk, irq);
+	if (ret)
+		return ret;
+
+	return sun5i_setup_clockevent(node, timer_base, clk, irq);
 }
-CLOCKSOURCE_OF_DECLARE(sun5i_a13, "allwinner,sun5i-a13-hstimer",
-		       sun5i_timer_init);
-CLOCKSOURCE_OF_DECLARE(sun7i_a20, "allwinner,sun7i-a20-hstimer",
-		       sun5i_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(sun5i_a13, "allwinner,sun5i-a13-hstimer",
+			   sun5i_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(sun7i_a20, "allwinner,sun7i-a20-hstimer",
+			   sun5i_timer_init);
Signature · 1 line
1.9.1
#86 lore raw

PATCH v2 49/63 clocksource/drivers/timer-ti-32k: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-ti-32k.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/clocksource/timer-ti-32k.c +6 -4
index 8518d9d..e4ad3c6e 100644
@@ -88,14 +88,14 @@ static u64 notrace omap_32k_read_sched_clock(void)
 	return ti_32k_read_cycles(&ti_32k_timer.cs);
 }
 
-static void __init ti_32k_timer_init(struct device_node *np)
+static int __init ti_32k_timer_init(struct device_node *np)
 {
 	int ret;
 
 	ti_32k_timer.base = of_iomap(np, 0);
 	if (!ti_32k_timer.base) {
 		pr_err("Can't ioremap 32k timer base\n");
-		return;
+		return -ENXIO;
 	}
 
 	ti_32k_timer.counter = ti_32k_timer.base;
@@ -116,11 +116,13 @@ static void __init ti_32k_timer_init(struct device_node *np)
 	ret = clocksource_register_hz(&ti_32k_timer.cs, 32768);
 	if (ret) {
 		pr_err("32k_counter: can't register clocksource\n");
-		return;
+		return ret;
 	}
 
 	sched_clock_register(omap_32k_read_sched_clock, 32, 32768);
 	pr_info("OMAP clocksource: 32k_counter at 32768 Hz\n");
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(ti_32k_timer, "ti,omap-counter32k",
+CLOCKSOURCE_OF_DECLARE_RET(ti_32k_timer, "ti,omap-counter32k",
 		ti_32k_timer_init);
Signature · 1 line
1.9.1
#87 lore raw

PATCH v2 50/63 clocksource/drivers/timer-u300: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-u300.c | 38 +++++++++++++++++++++++++++-----------
 1 file changed, 27 insertions(+), 11 deletions(-)
drivers/clocksource/timer-u300.c +27 -11
index 1744b24..a6a0dec 100644
@@ -359,27 +359,37 @@ static struct delay_timer u300_delay_timer;
 /*
  * This sets up the system timers, clock source and clock event.
  */
-static void __init u300_timer_init_of(struct device_node *np)
+static int __init u300_timer_init_of(struct device_node *np)
 {
 	unsigned int irq;
 	struct clk *clk;
 	unsigned long rate;
+	int ret;
 
 	u300_timer_base = of_iomap(np, 0);
-	if (!u300_timer_base)
-		panic("could not ioremap system timer\n");
+	if (!u300_timer_base) {
+		pr_err("could not ioremap system timer\n");
+		return -ENXIO;
+	}
 
 	/* Get the IRQ for the GP1 timer */
 	irq = irq_of_parse_and_map(np, 2);
-	if (!irq)
-		panic("no IRQ for system timer\n");
+	if (!irq) {
+		pr_err("no IRQ for system timer\n");
+		return -EINVAL;
+	}
 
 	pr_info("U300 GP1 timer @ base: %p, IRQ: %u\n", u300_timer_base, irq);
 
 	/* Clock the interrupt controller */
 	clk = of_clk_get(np, 0);
-	BUG_ON(IS_ERR(clk));
-	clk_prepare_enable(clk);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ret = clk_prepare_enable(clk);
+	if (ret)
+		return ret;
+
 	rate = clk_get_rate(clk);
 
 	u300_clockevent_data.ticks_per_jiffy = DIV_ROUND_CLOSEST(rate, HZ);
@@ -410,7 +420,9 @@ static void __init u300_timer_init_of(struct device_node *np)
 		u300_timer_base + U300_TIMER_APP_RGPT1);
 
 	/* Set up the IRQ handler */
-	setup_irq(irq, &u300_timer_irq);
+	ret = setup_irq(irq, &u300_timer_irq);
+	if (ret)
+		return ret;
 
 	/* Reset the General Purpose timer 2 */
 	writel(U300_TIMER_APP_RGPT2_TIMER_RESET,
@@ -428,9 +440,12 @@ static void __init u300_timer_init_of(struct device_node *np)
 		u300_timer_base + U300_TIMER_APP_EGPT2);
 
 	/* Use general purpose timer 2 as clock source */
-	if (clocksource_mmio_init(u300_timer_base + U300_TIMER_APP_GPT2CC,
-			"GPT2", rate, 300, 32, clocksource_mmio_readl_up))
+	ret = clocksource_mmio_init(u300_timer_base + U300_TIMER_APP_GPT2CC,
+				    "GPT2", rate, 300, 32, clocksource_mmio_readl_up);
+	if (ret) {
 		pr_err("timer: failed to initialize U300 clock source\n");
+		return ret;
+	}
 
 	/* Configure and register the clockevent */
 	clockevents_config_and_register(&u300_clockevent_data.cevd, rate,
@@ -440,7 +455,8 @@ static void __init u300_timer_init_of(struct device_node *np)
 	 * TODO: init and register the rest of the timers too, they can be
 	 * used by hrtimers!
 	 */
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(u300_timer, "stericsson,u300-apptimer",
+CLOCKSOURCE_OF_DECLARE_RET(u300_timer, "stericsson,u300-apptimer",
 		       u300_timer_init_of);
Signature · 1 line
1.9.1
Acked-by on v2 50/63
#88 lore raw

Re: [PATCH V2 50/63] clocksource/drivers/timer-u300: Convert init function to return error

Quoted 9 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Quoted 8 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Yours,
Linus Walleij

#89 lore raw

PATCH v2 51/63 clocksource/drivers/versatile: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/versatile.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/clocksource/versatile.c +6 -4
index 0a26d3d..8daeffa 100644
@@ -25,18 +25,20 @@ static u64 notrace versatile_sys_24mhz_read(void)
 	return readl(versatile_sys_24mhz);
 }
 
-static void __init versatile_sched_clock_init(struct device_node *node)
+static int __init versatile_sched_clock_init(struct device_node *node)
 {
 	void __iomem *base = of_iomap(node, 0);
 
 	if (!base)
-		return;
+		return -ENXIO;
 
 	versatile_sys_24mhz = base + SYS_24MHZ;
 
 	sched_clock_register(versatile_sys_24mhz_read, 32, 24000000);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(vexpress, "arm,vexpress-sysreg",
+CLOCKSOURCE_OF_DECLARE_RET(vexpress, "arm,vexpress-sysreg",
 		       versatile_sched_clock_init);
-CLOCKSOURCE_OF_DECLARE(versatile, "arm,versatile-sysreg",
+CLOCKSOURCE_OF_DECLARE_RET(versatile, "arm,versatile-sysreg",
 		       versatile_sched_clock_init);
Signature · 1 line
1.9.1
maintainer Acked-by on v2 51/63
#90 lore raw

Re: [PATCH V2 51/63] clocksource/drivers/versatile: Convert init function to return error

Quoted 53 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/versatile.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/clocksource/versatile.c +6 -4
index 0a26d3d..8daeffa 100644
@@ -25,18 +25,20 @@ static u64 notrace versatile_sys_24mhz_read(void)
 	return readl(versatile_sys_24mhz);
 }
 
-static void __init versatile_sched_clock_init(struct device_node *node)
+static int __init versatile_sched_clock_init(struct device_node *node)
 {
 	void __iomem *base = of_iomap(node, 0);
 
 	if (!base)
-		return;
+		return -ENXIO;
 
 	versatile_sys_24mhz = base + SYS_24MHZ;
 
 	sched_clock_register(versatile_sys_24mhz_read, 32, 24000000);
+
+	return 0;
 }
-CLOCKSOURCE_OF_DECLARE(vexpress, "arm,vexpress-sysreg",
+CLOCKSOURCE_OF_DECLARE_RET(vexpress, "arm,vexpress-sysreg",
 		       versatile_sched_clock_init);
-CLOCKSOURCE_OF_DECLARE(versatile, "arm,versatile-sysreg",
+CLOCKSOURCE_OF_DECLARE_RET(versatile, "arm,versatile-sysreg",
 		       versatile_sched_clock_init);
Signature · 1 line
1.9.1
Signature · 8 lines
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ?\_(?)_/?
#91 lore raw

PATCH v2 52/63 clocksource/drivers/vf_pit_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/vf_pit_timer.c | 27 ++++++++++++++++++---------
 1 file changed, 18 insertions(+), 9 deletions(-)
drivers/clocksource/vf_pit_timer.c +18 -9
index a0e6c68..ca4dff4 100644
@@ -156,15 +156,18 @@ static int __init pit_clockevent_init(unsigned long rate, int irq)
 	return 0;
 }
 
-static void __init pit_timer_init(struct device_node *np)
+static int __init pit_timer_init(struct device_node *np)
 {
 	struct clk *pit_clk;
 	void __iomem *timer_base;
 	unsigned long clk_rate;
-	int irq;
+	int irq, ret;
 
 	timer_base = of_iomap(np, 0);
-	BUG_ON(!timer_base);
+	if (!timer_base) {
+		pr_err("Failed to iomap");
+		return -ENXIO;
+	}
 
 	/*
 	 * PIT0 and PIT1 can be chained to build a 64-bit timer,
@@ -175,12 +178,16 @@ static void __init pit_timer_init(struct device_node *np)
 	clkevt_base = timer_base + PITn_OFFSET(3);
 
 	irq = irq_of_parse_and_map(np, 0);
-	BUG_ON(irq <= 0);
+	if (irq <= 0)
+		return -EINVAL;
 
 	pit_clk = of_clk_get(np, 0);
-	BUG_ON(IS_ERR(pit_clk));
+	if (IS_ERR(pit_clk))
+		return PTR_ERR(pit_clk);
 
-	BUG_ON(clk_prepare_enable(pit_clk));
+	ret = clk_prepare_enable(pit_clk);
+	if (ret)
+		return ret;
 
 	clk_rate = clk_get_rate(pit_clk);
 	cycle_per_jiffy = clk_rate / (HZ);
@@ -188,8 +195,10 @@ static void __init pit_timer_init(struct device_node *np)
 	/* enable the pit module */
 	__raw_writel(~PITMCR_MDIS, timer_base + PITMCR);
 
-	BUG_ON(pit_clocksource_init(clk_rate));
+	ret = pit_clocksource_init(clk_rate);
+	if (ret)
+		return ret;
 
-	pit_clockevent_init(clk_rate, irq);
+	return pit_clockevent_init(clk_rate, irq);
 }
-CLOCKSOURCE_OF_DECLARE(vf610, "fsl,vf610-pit", pit_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(vf610, "fsl,vf610-pit", pit_timer_init);
Signature · 1 line
1.9.1
#92 lore raw

PATCH v2 53/63 clocksource/drivers/vt8500_timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/vt8500_timer.c | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)
drivers/clocksource/vt8500_timer.c +18 -8
index ddb4092..1bc8707 100644
@@ -121,38 +121,48 @@ static struct irqaction irq = {
 	.dev_id  = &clockevent,
 };
 
-static void __init vt8500_timer_init(struct device_node *np)
+static int __init vt8500_timer_init(struct device_node *np)
 {
-	int timer_irq;
+	int timer_irq, ret;
 
 	regbase = of_iomap(np, 0);
 	if (!regbase) {
 		pr_err("%s: Missing iobase description in Device Tree\n",
 								__func__);
-		return;
+		return -ENXIO;
 	}
+
 	timer_irq = irq_of_parse_and_map(np, 0);
 	if (!timer_irq) {
 		pr_err("%s: Missing irq description in Device Tree\n",
 								__func__);
-		return;
+		return -EINVAL;
 	}
 
 	writel(1, regbase + TIMER_CTRL_VAL);
 	writel(0xf, regbase + TIMER_STATUS_VAL);
 	writel(~0, regbase + TIMER_MATCH_VAL);
 
-	if (clocksource_register_hz(&clocksource, VT8500_TIMER_HZ))
+	ret = clocksource_register_hz(&clocksource, VT8500_TIMER_HZ);
+	if (ret) {
 		pr_err("%s: vt8500_timer_init: clocksource_register failed for %s\n",
-					__func__, clocksource.name);
+		       __func__, clocksource.name);
+		return ret;
+	}
 
 	clockevent.cpumask = cpumask_of(0);
 
-	if (setup_irq(timer_irq, &irq))
+	ret = setup_irq(timer_irq, &irq);
+	if (ret) {
 		pr_err("%s: setup_irq failed for %s\n", __func__,
 							clockevent.name);
+		return ret;
+	}
+
 	clockevents_config_and_register(&clockevent, VT8500_TIMER_HZ,
 					MIN_OSCR_DELTA * 2, 0xf0000000);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(vt8500, "via,vt8500-timer", vt8500_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(vt8500, "via,vt8500-timer", vt8500_timer_init);
Signature · 1 line
1.9.1
#93 lore raw

PATCH v2 54/63 clocksource/drivers/zevio-timer: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/zevio-timer.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/clocksource/zevio-timer.c +3 -3
index ceaa613..cb4cf056 100644
@@ -210,9 +210,9 @@ error_free:
 	return ret;
 }
 
-static void __init zevio_timer_init(struct device_node *node)
+static int __init zevio_timer_init(struct device_node *node)
 {
-	BUG_ON(zevio_timer_add(node));
+	return zevio_timer_add(node);
 }
 
-CLOCKSOURCE_OF_DECLARE(zevio_timer, "lsi,zevio-timer", zevio_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(zevio_timer, "lsi,zevio-timer", zevio_timer_init);
Signature · 1 line
1.9.1
#94 lore raw

PATCH v2 55/63 clocksource/drivers/timer-sp804: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 include/clocksource/timer-sp804.h | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
include/clocksource/timer-sp804.h +4 -4
index 1f8a1ca..7654d71 100644
@@ -3,10 +3,10 @@
 
 struct clk;
 
-void __sp804_clocksource_and_sched_clock_init(void __iomem *,
-					      const char *, struct clk *, int);
-void __sp804_clockevents_init(void __iomem *, unsigned int,
-			      struct clk *, const char *);
+int __sp804_clocksource_and_sched_clock_init(void __iomem *,
+					     const char *, struct clk *, int);
+int __sp804_clockevents_init(void __iomem *, unsigned int,
+			     struct clk *, const char *);
 void sp804_timer_disable(void __iomem *);
 
 static inline void sp804_clocksource_init(void __iomem *base, const char *name)
Signature · 1 line
1.9.1
#95 lore raw

PATCH v2 56/63 clocksource/drivers/microblaze: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 arch/microblaze/kernel/timer.c | 51 +++++++++++++++++++++++++++++++-----------
 1 file changed, 38 insertions(+), 13 deletions(-)
arch/microblaze/kernel/timer.c +38 -13
index 67e2ef4..7f35e7b 100644
@@ -170,7 +170,7 @@ static struct irqaction timer_irqaction = {
 	.dev_id = &clockevent_xilinx_timer,
 };
 
-static __init void xilinx_clockevent_init(void)
+static __init int xilinx_clockevent_init(void)
 {
 	clockevent_xilinx_timer.mult =
 		div_sc(timer_clock_freq, NSEC_PER_SEC,
@@ -181,6 +181,8 @@ static __init void xilinx_clockevent_init(void)
 		clockevent_delta2ns(1, &clockevent_xilinx_timer);
 	clockevent_xilinx_timer.cpumask = cpumask_of(0);
 	clockevents_register_device(&clockevent_xilinx_timer);
+
+	return 0;
 }
 
 static u64 xilinx_clock_read(void)
@@ -229,8 +231,14 @@ static struct clocksource clocksource_microblaze = {
 
 static int __init xilinx_clocksource_init(void)
 {
-	if (clocksource_register_hz(&clocksource_microblaze, timer_clock_freq))
-		panic("failed to register clocksource");
+	int ret;
+
+	ret = clocksource_register_hz(&clocksource_microblaze,
+				      timer_clock_freq);
+	if (ret) {
+		pr_err("failed to register clocksource");
+		return ret;
+	}
 
 	/* stop timer1 */
 	write_fn(read_fn(timer_baseaddr + TCSR1) & ~TCSR_ENT,
@@ -239,16 +247,16 @@ static int __init xilinx_clocksource_init(void)
 	write_fn(TCSR_TINT|TCSR_ENT|TCSR_ARHT, timer_baseaddr + TCSR1);
 
 	/* register timecounter - for ftrace support */
-	init_xilinx_timecounter();
-	return 0;
+	return init_xilinx_timecounter();
 }
 
-static void __init xilinx_timer_init(struct device_node *timer)
+static int __init xilinx_timer_init(struct device_node *timer)
 {
 	struct clk *clk;
 	static int initialized;
 	u32 irq;
 	u32 timer_num = 1;
+	int ret;
 
 	if (initialized)
 		return;
@@ -258,7 +266,7 @@ static void __init xilinx_timer_init(struct device_node *timer)
 	timer_baseaddr = of_iomap(timer, 0);
 	if (!timer_baseaddr) {
 		pr_err("ERROR: invalid timer base address\n");
-		BUG();
+		return -ENXIO;
 	}
 
 	write_fn = timer_write32;
@@ -271,11 +279,15 @@ static void __init xilinx_timer_init(struct device_node *timer)
 	}
 
 	irq = irq_of_parse_and_map(timer, 0);
+	if (irq <= 0) {
+		pr_err("Failed to parse and map irq");
+		return -EINVAL;
+	}
 
 	of_property_read_u32(timer, "xlnx,one-timer-only", &timer_num);
 	if (timer_num) {
-		pr_emerg("Please enable two timers in HW\n");
-		BUG();
+		pr_err("Please enable two timers in HW\n");
+		return -EINVAL;
 	}
 
 	pr_info("%s: irq=%d\n", timer->full_name, irq);
@@ -297,15 +309,28 @@ static void __init xilinx_timer_init(struct device_node *timer)
 
 	freq_div_hz = timer_clock_freq / HZ;
 
-	setup_irq(irq, &timer_irqaction);
+	ret = setup_irq(irq, &timer_irqaction);
+	if (ret) {
+		pr_err("Failed to setup IRQ");
+		return ret;
+	}
+
 #ifdef CONFIG_HEART_BEAT
 	microblaze_setup_heartbeat();
 #endif
-	xilinx_clocksource_init();
-	xilinx_clockevent_init();
+
+	ret = xilinx_clocksource_init();
+	if (ret)
+		return ret;
+
+	ret = xilinx_clockevent_init();
+	if (ret)
+		return ret;
 
 	sched_clock_register(xilinx_clock_read, 32, timer_clock_freq);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(xilinx_timer, "xlnx,xps-timer-1.00.a",
+CLOCKSOURCE_OF_DECLARE_RET(xilinx_timer, "xlnx,xps-timer-1.00.a",
 		       xilinx_timer_init);
Signature · 1 line
1.9.1
#96 lore raw

PATCH v2 57/63 clocksource/drivers/ralink: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 arch/mips/ralink/cevt-rt3352.c | 19 +++++++++++++------
 1 file changed, 13 insertions(+), 6 deletions(-)
arch/mips/ralink/cevt-rt3352.c +13 -6
index 3ad0b07..f2d3c79 100644
@@ -117,11 +117,13 @@ static int systick_set_oneshot(struct clock_event_device *evt)
 	return 0;
 }
 
-static void __init ralink_systick_init(struct device_node *np)
+static int __init ralink_systick_init(struct device_node *np)
 {
+	int ret;
+
 	systick.membase = of_iomap(np, 0);
 	if (!systick.membase)
-		return;
+		return -ENXIO;
 
 	systick_irqaction.name = np->name;
 	systick.dev.name = np->name;
@@ -131,16 +133,21 @@ static void __init ralink_systick_init(struct device_node *np)
 	systick.dev.irq = irq_of_parse_and_map(np, 0);
 	if (!systick.dev.irq) {
 		pr_err("%s: request_irq failed", np->name);
-		return;
+		return -EINVAL;
 	}
 
-	clocksource_mmio_init(systick.membase + SYSTICK_COUNT, np->name,
-			SYSTICK_FREQ, 301, 16, clocksource_mmio_readl_up);
+	ret = clocksource_mmio_init(systick.membase + SYSTICK_COUNT, np->name,
+				    SYSTICK_FREQ, 301, 16,
+				    clocksource_mmio_readl_up);
+	if (ret)
+		return ret;
 
 	clockevents_register_device(&systick.dev);
 
 	pr_info("%s: running - mult: %d, shift: %d\n",
 			np->name, systick.dev.mult, systick.dev.shift);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(systick, "ralink,cevt-systick", ralink_systick_init);
+CLOCKSOURCE_OF_DECLARE_RET(systick, "ralink,cevt-systick", ralink_systick_init);
Signature · 1 line
1.9.1
maintainer Acked-by on v2 57/63
#97 lore raw

Re: [PATCH V2 57/63] clocksource/drivers/ralink: Convert init function to return error

Quoted 9 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Quoted 8 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Quoted 51 lines
---
 arch/mips/ralink/cevt-rt3352.c | 19 +++++++++++++------
 1 file changed, 13 insertions(+), 6 deletions(-)
arch/mips/ralink/cevt-rt3352.c +13 -6
index 3ad0b07..f2d3c79 100644
@@ -117,11 +117,13 @@ static int systick_set_oneshot(struct clock_event_device *evt)
 	return 0;
 }
 
-static void __init ralink_systick_init(struct device_node *np)
+static int __init ralink_systick_init(struct device_node *np)
 {
+	int ret;
+
 	systick.membase = of_iomap(np, 0);
 	if (!systick.membase)
-		return;
+		return -ENXIO;
 
 	systick_irqaction.name = np->name;
 	systick.dev.name = np->name;
@@ -131,16 +133,21 @@ static void __init ralink_systick_init(struct device_node *np)
 	systick.dev.irq = irq_of_parse_and_map(np, 0);
 	if (!systick.dev.irq) {
 		pr_err("%s: request_irq failed", np->name);
-		return;
+		return -EINVAL;
 	}
 
-	clocksource_mmio_init(systick.membase + SYSTICK_COUNT, np->name,
-			SYSTICK_FREQ, 301, 16, clocksource_mmio_readl_up);
+	ret = clocksource_mmio_init(systick.membase + SYSTICK_COUNT, np->name,
+				    SYSTICK_FREQ, 301, 16,
+				    clocksource_mmio_readl_up);
+	if (ret)
+		return ret;
 
 	clockevents_register_device(&systick.dev);
 
 	pr_info("%s: running - mult: %d, shift: %d\n",
 			np->name, systick.dev.mult, systick.dev.shift);
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(systick, "ralink,cevt-systick", ralink_systick_init);
+CLOCKSOURCE_OF_DECLARE_RET(systick, "ralink,cevt-systick", ralink_systick_init);
#98 lore raw

PATCH v2 58/63 clocksource/drivers/nios2: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 arch/nios2/kernel/time.c | 69 +++++++++++++++++++++++++++++++++---------------
 1 file changed, 48 insertions(+), 21 deletions(-)
arch/nios2/kernel/time.c +48 -21
index e835dda..9fa7739 100644
@@ -206,15 +206,21 @@ irqreturn_t timer_interrupt(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
-static void __init nios2_timer_get_base_and_freq(struct device_node *np,
+static int __init nios2_timer_get_base_and_freq(struct device_node *np,
 				void __iomem **base, u32 *freq)
 {
 	*base = of_iomap(np, 0);
-	if (!*base)
-		panic("Unable to map reg for %s\n", np->name);
+	if (!*base) {
+		pr_crit("Unable to map reg for %s\n", np->name);
+		return -ENXIO;
+	}
+
+	if (of_property_read_u32(np, "clock-frequency", freq)) {
+		pr_crit("Unable to get %s clock frequency\n", np->name);
+		return -EINVAL;
+	}
 
-	if (of_property_read_u32(np, "clock-frequency", freq))
-		panic("Unable to get %s clock frequency\n", np->name);
+	return 0;
 }
 
 static struct nios2_clockevent_dev nios2_ce = {
@@ -231,17 +237,21 @@ static struct nios2_clockevent_dev nios2_ce = {
 	},
 };
 
-static __init void nios2_clockevent_init(struct device_node *timer)
+static __init int nios2_clockevent_init(struct device_node *timer)
 {
 	void __iomem *iobase;
 	u32 freq;
-	int irq;
+	int irq, ret;
 
-	nios2_timer_get_base_and_freq(timer, &iobase, &freq);
+	ret = nios2_timer_get_base_and_freq(timer, &iobase, &freq);
+	if (ret)
+		return ret;
 
 	irq = irq_of_parse_and_map(timer, 0);
-	if (!irq)
-		panic("Unable to parse timer irq\n");
+	if (!irq) {
+		pr_crit("Unable to parse timer irq\n");
+		return -EINVAL;
+	}
 
 	nios2_ce.timer.base = iobase;
 	nios2_ce.timer.freq = freq;
@@ -253,25 +263,35 @@ static __init void nios2_clockevent_init(struct device_node *timer)
 	/* clear pending interrupt */
 	timer_writew(&nios2_ce.timer, 0, ALTERA_TIMER_STATUS_REG);
 
-	if (request_irq(irq, timer_interrupt, IRQF_TIMER, timer->name,
-		&nios2_ce.ced))
-		panic("Unable to setup timer irq\n");
+	ret = request_irq(irq, timer_interrupt, IRQF_TIMER, timer->name,
+			  &nios2_ce.ced);
+	if (ret) {
+		pr_crit("Unable to setup timer irq\n");
+		return ret;
+	}
 
 	clockevents_config_and_register(&nios2_ce.ced, freq, 1, ULONG_MAX);
+
+	return 0;
 }
 
-static __init void nios2_clocksource_init(struct device_node *timer)
+static __init int nios2_clocksource_init(struct device_node *timer)
 {
 	unsigned int ctrl;
 	void __iomem *iobase;
 	u32 freq;
+	int ret;
 
-	nios2_timer_get_base_and_freq(timer, &iobase, &freq);
+	ret = nios2_timer_get_base_and_freq(timer, &iobase, &freq);
+	if (ret)
+		return ret;
 
 	nios2_cs.timer.base = iobase;
 	nios2_cs.timer.freq = freq;
 
-	clocksource_register_hz(&nios2_cs.cs, freq);
+	ret = clocksource_register_hz(&nios2_cs.cs, freq);
+	if (ret)
+		return ret;
 
 	timer_writew(&nios2_cs.timer, USHRT_MAX, ALTERA_TIMER_PERIODL_REG);
 	timer_writew(&nios2_cs.timer, USHRT_MAX, ALTERA_TIMER_PERIODH_REG);
@@ -282,6 +302,8 @@ static __init void nios2_clocksource_init(struct device_node *timer)
 
 	/* Calibrate the delay loop directly */
 	lpj_fine = freq / HZ;
+
+	return 0;
 }
 
 /*
@@ -289,22 +311,25 @@ static __init void nios2_clocksource_init(struct device_node *timer)
  * more instances, the second one gets used as clocksource and all
  * others are unused.
 */
-static void __init nios2_time_init(struct device_node *timer)
+static int __init nios2_time_init(struct device_node *timer)
 {
 	static int num_called;
+	int ret;
 
 	switch (num_called) {
 	case 0:
-		nios2_clockevent_init(timer);
+		ret = nios2_clockevent_init(timer);
 		break;
 	case 1:
-		nios2_clocksource_init(timer);
+		ret = nios2_clocksource_init(timer);
 		break;
 	default:
 		break;
 	}
 
 	num_called++;
+
+	return ret;
 }
 
 void read_persistent_clock(struct timespec *ts)
@@ -321,10 +346,12 @@ void __init time_init(void)
 	for_each_compatible_node(np, NULL,  ALTR_TIMER_COMPATIBLE)
 		count++;
 
-	if (count < 2)
+	if (count < 2) {
 		panic("%d timer is found, it needs 2 timers in system\n", count);
 
 	clocksource_probe();
+
+	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE(nios2_timer, ALTR_TIMER_COMPATIBLE, nios2_time_init);
+CLOCKSOURCE_OF_DECLARE_RET(nios2_timer, ALTR_TIMER_COMPATIBLE, nios2_time_init);
Signature · 1 line
1.9.1
#99 lore raw

PATCH v2 59/63 clocksource/drivers/smp_twd: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 arch/arm/kernel/smp_twd.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
arch/arm/kernel/smp_twd.c +5 -4
index 1bfa7a7..2b24be4 100644
@@ -390,7 +390,7 @@ int __init twd_local_timer_register(struct twd_local_timer *tlt)
 }
 
 #ifdef CONFIG_OF
-static void __init twd_local_timer_of_register(struct device_node *np)
+static int __init twd_local_timer_of_register(struct device_node *np)
 {
 	int err;
 
@@ -410,8 +410,9 @@ static void __init twd_local_timer_of_register(struct device_node *np)
 
 out:
 	WARN(err, "twd_local_timer_of_register failed (%d)\n", err);
+	return err;
 }
-CLOCKSOURCE_OF_DECLARE(arm_twd_a9, "arm,cortex-a9-twd-timer", twd_local_timer_of_register);
-CLOCKSOURCE_OF_DECLARE(arm_twd_a5, "arm,cortex-a5-twd-timer", twd_local_timer_of_register);
-CLOCKSOURCE_OF_DECLARE(arm_twd_11mp, "arm,arm11mp-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE_RET(arm_twd_a9, "arm,cortex-a9-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE_RET(arm_twd_a5, "arm,cortex-a5-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE_RET(arm_twd_11mp, "arm,arm11mp-twd-timer", twd_local_timer_of_register);
 #endif
Signature · 1 line
1.9.1
#100 lore raw

PATCH v2 60/63 clocksource/drivers/nps: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-nps.c | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)
drivers/clocksource/timer-nps.c +10 -8
index d461089..b5c7b2b 100644
@@ -55,8 +55,8 @@ static cycle_t nps_clksrc_read(struct clocksource *clksrc)
 	return (cycle_t)ioread32be(nps_msu_reg_low_addr[cluster]);
 }
 
-static void __init nps_setup_clocksource(struct device_node *node,
-					 struct clk *clk)
+static int __init nps_setup_clocksource(struct device_node *node,
+					struct clk *clk)
 {
 	int ret, cluster;
 
@@ -68,7 +68,7 @@ static void __init nps_setup_clocksource(struct device_node *node,
 	ret = clk_prepare_enable(clk);
 	if (ret) {
 		pr_err("Couldn't enable parent clock\n");
-		return;
+		return ret;
 	}
 
 	nps_timer_rate = clk_get_rate(clk);
@@ -79,20 +79,22 @@ static void __init nps_setup_clocksource(struct device_node *node,
 		pr_err("Couldn't register clock source.\n");
 		clk_disable_unprepare(clk);
 	}
+
+	return ret;
 }
 
-static void __init nps_timer_init(struct device_node *node)
+static int __init nps_timer_init(struct device_node *node)
 {
 	struct clk *clk;
 
 	clk = of_clk_get(node, 0);
 	if (IS_ERR(clk)) {
 		pr_err("Can't get timer clock.\n");
-		return;
+		return PTR_ERR(clk);
 	}
 
-	nps_setup_clocksource(node, clk);
+	return nps_setup_clocksource(node, clk);
 }
 
-CLOCKSOURCE_OF_DECLARE(ezchip_nps400_clksrc, "ezchip,nps400-timer",
-		       nps_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(ezchip_nps400_clksrc, "ezchip,nps400-timer",
+			   nps_timer_init);
Signature · 1 line
1.9.1
#101 lore raw

PATCH v2 61/63 clocksource/drivers/arc: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Signed-off-by Daniel Lezcano <daniel.lezcano at linaro.org>
---
 arch/arc/kernel/time.c | 69 ++++++++++++++++++++++++++++++--------------------
 1 file changed, 42 insertions(+), 27 deletions(-)
arch/arc/kernel/time.c +42 -27
index 4549ab2..36110cd 100644
@@ -116,21 +116,21 @@ static struct clocksource arc_counter_gfrc = {
 	.flags  = CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-static void __init arc_cs_setup_gfrc(struct device_node *node)
+static int __init arc_cs_setup_gfrc(struct device_node *node)
 {
 	int exists = cpuinfo_arc700[0].extn.gfrc;
 	int ret;
 
 	if (WARN(!exists, "Global-64-bit-Ctr clocksource not detected"))
-		return;
+		return -ENXIO;
 
 	ret = arc_get_timer_clk(node);
 	if (ret)
-		return;
+		return ret;
 
-	clocksource_register_hz(&arc_counter_gfrc, arc_timer_freq);
+	return clocksource_register_hz(&arc_counter_gfrc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
+CLOCKSOURCE_OF_DECLARE_RET(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
 
 #endif
 
@@ -172,27 +172,27 @@ static struct clocksource arc_counter_rtc = {
 	.flags  = CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-static void __init arc_cs_setup_rtc(struct device_node *node)
+static int __init arc_cs_setup_rtc(struct device_node *node)
 {
 	int exists = cpuinfo_arc700[smp_processor_id()].extn.rtc;
 	int ret;
 
 	if (WARN(!exists, "Local-64-bit-Ctr clocksource not detected"))
-		return;
+		return -ENXIO;
 
 	/* Local to CPU hence not usable in SMP */
 	if (WARN(IS_ENABLED(CONFIG_SMP), "Local-64-bit-Ctr not usable in SMP"))
-		return;
+		return -EINVAL;
 
 	ret = arc_get_timer_clk(node);
 	if (ret)
-		return;
+		return ret;
 
 	write_aux_reg(AUX_RTC_CTRL, 1);
 
-	clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
+	return clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
+CLOCKSOURCE_OF_DECLARE_RET(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
 
 #endif
 
@@ -213,23 +213,23 @@ static struct clocksource arc_counter_timer1 = {
 	.flags  = CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-static void __init arc_cs_setup_timer1(struct device_node *node)
+static int __init arc_cs_setup_timer1(struct device_node *node)
 {
 	int ret;
 
 	/* Local to CPU hence not usable in SMP */
 	if (IS_ENABLED(CONFIG_SMP))
-		return;
+		return 0;
 
 	ret = arc_get_timer_clk(node);
 	if (ret)
-		return;
+		return ret;
 
 	write_aux_reg(ARC_REG_TIMER1_LIMIT, ARC_TIMER_MAX);
 	write_aux_reg(ARC_REG_TIMER1_CNT, 0);
 	write_aux_reg(ARC_REG_TIMER1_CTRL, TIMER_CTRL_NH);
 
-	clocksource_register_hz(&arc_counter_timer1, arc_timer_freq);
+	return clocksource_register_hz(&arc_counter_timer1, arc_timer_freq);
 }
 
 /********** Clock Event Device *********/
@@ -324,20 +324,28 @@ static struct notifier_block arc_timer_cpu_nb = {
 /*
  * clockevent setup for boot CPU
  */
-static void __init arc_clockevent_setup(struct device_node *node)
+static int __init arc_clockevent_setup(struct device_node *node)
 {
 	struct clock_event_device *evt = this_cpu_ptr(&arc_clockevent_device);
 	int ret;
 
-	register_cpu_notifier(&arc_timer_cpu_nb);
+	ret = register_cpu_notifier(&arc_timer_cpu_nb);
+	if (ret) {
+		pr_err("Failed to register cpu notifier");
+		return ret;
+	}
 
 	arc_timer_irq = irq_of_parse_and_map(node, 0);
-	if (arc_timer_irq <= 0)
-		panic("clockevent: missing irq");
+	if (arc_timer_irq <= 0) {
+		pr_err("clockevent: missing irq");
+		return -EINVAL;
+	}
 
 	ret = arc_get_timer_clk(node);
-	if (ret)
-		panic("clockevent: missing clk");
+	if (ret) {
+		pr_err("clockevent: missing clk");
+		return ret;
+	}
 
 	evt->irq = arc_timer_irq;
 	evt->cpumask = cpumask_of(smp_processor_id());
@@ -347,24 +355,31 @@ static void __init arc_clockevent_setup(struct device_node *node)
 	/* Needs apriori irq_set_percpu_devid() done in intc map function */
 	ret = request_percpu_irq(arc_timer_irq, timer_irq_handler,
 				 "Timer0 (per-cpu-tick)", evt);
-	if (ret)
-		panic("clockevent: unable to request irq\n");
+	if (ret) {
+		pr_err("clockevent: unable to request irq\n");
+		returnr ret;
+	}
 
 	enable_percpu_irq(arc_timer_irq, 0);
+
+	return 0;
 }
 
-static void __init arc_of_timer_init(struct device_node *np)
+static int __init arc_of_timer_init(struct device_node *np)
 {
 	static int init_count = 0;
+	int ret;
 
 	if (!init_count) {
 		init_count = 1;
-		arc_clockevent_setup(np);
+		ret = arc_clockevent_setup(np);
 	} else {
-		arc_cs_setup_timer1(np);
+		ret = arc_cs_setup_timer1(np);
 	}
+
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(arc_clkevt, "snps,arc-timer", arc_of_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(arc_clkevt, "snps,arc-timer", arc_of_timer_init);
 
 /*
  * Called from start_kernel() - boot CPU only
Signature · 1 line
1.9.1
#102 lore raw

Re: [PATCH V2 61/63] clocksource/drivers/arc: Convert init function to return error

Quoted 18 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Signed-off-by Daniel Lezcano <daniel.lezcano at linaro.org>

---

[...]

Quoted 38 lines
arch/arc/kernel/time.c +6 -6
@@ -172,27 +172,27 @@ static struct clocksource arc_counter_rtc = {
 	.flags  = CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-static void __init arc_cs_setup_rtc(struct device_node *node)
+static int __init arc_cs_setup_rtc(struct device_node *node)
 {
 	int exists = cpuinfo_arc700[smp_processor_id()].extn.rtc;
 	int ret;
 
 	if (WARN(!exists, "Local-64-bit-Ctr clocksource not detected"))
-		return;
+		return -ENXIO;
 
 	/* Local to CPU hence not usable in SMP */
 	if (WARN(IS_ENABLED(CONFIG_SMP), "Local-64-bit-Ctr not usable in SMP"))
-		return;
+		return -EINVAL;
 
 	ret = arc_get_timer_clk(node);
 	if (ret)
-		return;
+		return ret;
 
 	write_aux_reg(AUX_RTC_CTRL, 1);
 
-	clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
+	return clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
+CLOCKSOURCE_OF_DECLARE_RET(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
 
 #endif
 
@@ -213,23 +213,23 @@ static struct clocksource arc_counter_timer1 = {
 	.flags  = CLOCK_SOURCE_IS_CONTINUOUS,
 };

arch/arc/kernel/time.c static struct clocksource arc_counter_timer1 = { · line 222

Quoted 10 lines
arch/arc/kernel/time.c +2 -2
 
-static void __init arc_cs_setup_timer1(struct device_node *node)
+static int __init arc_cs_setup_timer1(struct device_node *node)
 {
 	int ret;
 
 	/* Local to CPU hence not usable in SMP */
 	if (IS_ENABLED(CONFIG_SMP))
-		return;
+		return 0;

-EINVAL to keep it similar as rtc above

#103 lore raw

PATCH v3 1/1 clocksource/drivers/arc: Convert init function to return error

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Signed-off-by Daniel Lezcano <daniel.lezcano at linaro.org>
---
 arch/arc/kernel/time.c | 69 ++++++++++++++++++++++++++++++--------------------
 1 file changed, 42 insertions(+), 27 deletions(-)
arch/arc/kernel/time.c +42 -27
index 4549ab2..b211f80 100644
@@ -116,21 +116,21 @@ static struct clocksource arc_counter_gfrc = {
 	.flags  = CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-static void __init arc_cs_setup_gfrc(struct device_node *node)
+static int __init arc_cs_setup_gfrc(struct device_node *node)
 {
 	int exists = cpuinfo_arc700[0].extn.gfrc;
 	int ret;
 
 	if (WARN(!exists, "Global-64-bit-Ctr clocksource not detected"))
-		return;
+		return -ENXIO;
 
 	ret = arc_get_timer_clk(node);
 	if (ret)
-		return;
+		return ret;
 
-	clocksource_register_hz(&arc_counter_gfrc, arc_timer_freq);
+	return clocksource_register_hz(&arc_counter_gfrc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
+CLOCKSOURCE_OF_DECLARE_RET(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
 
 #endif
 
@@ -172,27 +172,27 @@ static struct clocksource arc_counter_rtc = {
 	.flags  = CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-static void __init arc_cs_setup_rtc(struct device_node *node)
+static int __init arc_cs_setup_rtc(struct device_node *node)
 {
 	int exists = cpuinfo_arc700[smp_processor_id()].extn.rtc;
 	int ret;
 
 	if (WARN(!exists, "Local-64-bit-Ctr clocksource not detected"))
-		return;
+		return -ENXIO;
 
 	/* Local to CPU hence not usable in SMP */
 	if (WARN(IS_ENABLED(CONFIG_SMP), "Local-64-bit-Ctr not usable in SMP"))
-		return;
+		return -EINVAL;
 
 	ret = arc_get_timer_clk(node);
 	if (ret)
-		return;
+		return ret;
 
 	write_aux_reg(AUX_RTC_CTRL, 1);
 
-	clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
+	return clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
+CLOCKSOURCE_OF_DECLARE_RET(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
 
 #endif
 
@@ -213,23 +213,23 @@ static struct clocksource arc_counter_timer1 = {
 	.flags  = CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-static void __init arc_cs_setup_timer1(struct device_node *node)
+static int __init arc_cs_setup_timer1(struct device_node *node)
 {
 	int ret;
 
 	/* Local to CPU hence not usable in SMP */
 	if (IS_ENABLED(CONFIG_SMP))
-		return;
+		return -EINVAL;
 
 	ret = arc_get_timer_clk(node);
 	if (ret)
-		return;
+		return ret;
 
 	write_aux_reg(ARC_REG_TIMER1_LIMIT, ARC_TIMER_MAX);
 	write_aux_reg(ARC_REG_TIMER1_CNT, 0);
 	write_aux_reg(ARC_REG_TIMER1_CTRL, TIMER_CTRL_NH);
 
-	clocksource_register_hz(&arc_counter_timer1, arc_timer_freq);
+	return clocksource_register_hz(&arc_counter_timer1, arc_timer_freq);
 }
 
 /********** Clock Event Device *********/
@@ -324,20 +324,28 @@ static struct notifier_block arc_timer_cpu_nb = {
 /*
  * clockevent setup for boot CPU
  */
-static void __init arc_clockevent_setup(struct device_node *node)
+static int __init arc_clockevent_setup(struct device_node *node)
 {
 	struct clock_event_device *evt = this_cpu_ptr(&arc_clockevent_device);
 	int ret;
 
-	register_cpu_notifier(&arc_timer_cpu_nb);
+	ret = register_cpu_notifier(&arc_timer_cpu_nb);
+	if (ret) {
+		pr_err("Failed to register cpu notifier");
+		return ret;
+	}
 
 	arc_timer_irq = irq_of_parse_and_map(node, 0);
-	if (arc_timer_irq <= 0)
-		panic("clockevent: missing irq");
+	if (arc_timer_irq <= 0) {
+		pr_err("clockevent: missing irq");
+		return -EINVAL;
+	}
 
 	ret = arc_get_timer_clk(node);
-	if (ret)
-		panic("clockevent: missing clk");
+	if (ret) {
+		pr_err("clockevent: missing clk");
+		return ret;
+	}
 
 	evt->irq = arc_timer_irq;
 	evt->cpumask = cpumask_of(smp_processor_id());
@@ -347,24 +355,31 @@ static void __init arc_clockevent_setup(struct device_node *node)
 	/* Needs apriori irq_set_percpu_devid() done in intc map function */
 	ret = request_percpu_irq(arc_timer_irq, timer_irq_handler,
 				 "Timer0 (per-cpu-tick)", evt);
-	if (ret)
-		panic("clockevent: unable to request irq\n");
+	if (ret) {
+		pr_err("clockevent: unable to request irq\n");
+		returnr ret;
+	}
 
 	enable_percpu_irq(arc_timer_irq, 0);
+
+	return 0;
 }
 
-static void __init arc_of_timer_init(struct device_node *np)
+static int __init arc_of_timer_init(struct device_node *np)
 {
 	static int init_count = 0;
+	int ret;
 
 	if (!init_count) {
 		init_count = 1;
-		arc_clockevent_setup(np);
+		ret = arc_clockevent_setup(np);
 	} else {
-		arc_cs_setup_timer1(np);
+		ret = arc_cs_setup_timer1(np);
 	}
+
+	return ret;
 }
-CLOCKSOURCE_OF_DECLARE(arc_clkevt, "snps,arc-timer", arc_of_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(arc_clkevt, "snps,arc-timer", arc_of_timer_init);
 
 /*
  * Called from start_kernel() - boot CPU only
Signature · 1 line
1.9.1
Acked-by on v3 1/1
#104 lore raw

Re: [PATCH V3] clocksource/drivers/arc: Convert init function to return error

Quoted 9 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Quoted 8 lines

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Signed-off-by Daniel Lezcano <daniel.lezcano at linaro.org>
Acked-by Vineet Gupta <vgupta at synopsys.com>

P.S. It would be nice to get cover letter for a series in addition to relevant patches for full context, although per prev discussion on ARC timers, I kind of knew what the idea was !

#105 lore raw

Re: [PATCH V3] clocksource/drivers/arc: Convert init function to return error

In reply to Daniel Lezcano
Quoted 19 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Signed-off-by Daniel Lezcano <daniel.lezcano at linaro.org>
---
 arch/arc/kernel/time.c | 69 ++++++++++++++++++++++++++++++--------------------

[...]

arch/arc/kernel/time.c static void __init arc_clockevent_setup(struct device_node *node) · line 360

Quoted 10 lines
arch/arc/kernel/time.c +3 -2
 	evt->cpumask = cpumask_of(smp_processor_id());
@@ -347,24 +355,31 @@ static void __init arc_clockevent_setup(struct device_node *node)
 	/* Needs apriori irq_set_percpu_devid() done in intc map function */
 	ret = request_percpu_irq(arc_timer_irq, timer_irq_handler,
 				 "Timer0 (per-cpu-tick)", evt);
-	if (ret)
-		panic("clockevent: unable to request irq\n");
+	if (ret) {
+		pr_err("clockevent: unable to request irq\n");
+		returnr ret;

oops I missed the typo here !
Daniel can u squash this to ur patch !

-Vineet

#106 lore raw

Re: [PATCH V3] clocksource/drivers/arc: Convert init function to return error

Quoted 23 lines · Vineet Gupta
Quoted 19 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

Signed-off-by Daniel Lezcano <daniel.lezcano at linaro.org>
---
  arch/arc/kernel/time.c | 69 ++++++++++++++++++++++++++++++--------------------

[...]

Quoted 13 lines

arch/arc/kernel/time.c static void __init arc_clockevent_setup(struct device_node *node) · line 360

Quoted 10 lines
  	evt->cpumask = cpumask_of(smp_processor_id());
arch/arc/kernel/time.c +3 -2
@@ -347,24 +355,31 @@ static void __init arc_clockevent_setup(struct device_node *node)
  	/* Needs apriori irq_set_percpu_devid() done in intc map function */
  	ret = request_percpu_irq(arc_timer_irq, timer_irq_handler,
  				 "Timer0 (per-cpu-tick)", evt);
-	if (ret)
-		panic("clockevent: unable to request irq\n");
+	if (ret) {
+		pr_err("clockevent: unable to request irq\n");
+		returnr ret;

oops I missed the typo here !
Daniel can u squash this to ur patch !

Yes, no problem.

Do you agree to move the driver to drivers/clocksource, so we can add the COMPILE_TEST option ?

Thanks.

-- Daniel

Signature · 5 lines
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#107 lore raw

Re: [PATCH V3] clocksource/drivers/arc: Convert init function to return error

Quoted 2 lines · Daniel Lezcano

Do you agree to move the driver to drivers/clocksource, so we can add the COMPILE_TEST option ?

Sure, this will require some common header adjustments etc. After the current fire-drill I'm pulled into ATM, I'll work on it next week'ish !

-Vineet

#108 lore raw

Re: [PATCH V3] clocksource/drivers/arc: Convert init function to return error

Quoted 6 lines · Vineet Gupta
Quoted 2 lines · Daniel Lezcano

Do you agree to move the driver to drivers/clocksource, so we can add the COMPILE_TEST option ?

Sure, this will require some common header adjustments etc. After the current fire-drill I'm pulled into ATM, I'll work on it next week'ish !

Great, thanks !

Signature · 5 lines
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#109 lore raw

PATCH v2 62/63 clocksource/drivers/oxnas-rps: Convert init function to return error

In reply to Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-oxnas-rps.c | 33 ++++++++++++++++++++-------------
 1 file changed, 20 insertions(+), 13 deletions(-)
drivers/clocksource/timer-oxnas-rps.c +20 -13
index c002e99..0d99f40 100644
@@ -220,32 +220,37 @@ static int __init oxnas_rps_clocksource_init(struct oxnas_rps_timer *rps)
 	return 0;
 }
 
-static void __init oxnas_rps_timer_init(struct device_node *np)
+static int __init oxnas_rps_timer_init(struct device_node *np)
 {
 	struct oxnas_rps_timer *rps;
 	void __iomem *base;
 	int ret;
 
 	rps = kzalloc(sizeof(*rps), GFP_KERNEL);
-	if (!rps) {
-		pr_err("Failed to allocate rps structure\n");
-		return;
-	}
+	if (!rps)
+		return -ENOMEM;
 
 	rps->clk = of_clk_get(np, 0);
-	if (WARN_ON(IS_ERR(rps->clk)))
+	if (IS_ERR(rps->clk)) {
+		ret = PTR_ERR(rps->clk);
 		goto err_alloc;
+	}
 
-	if (WARN_ON(clk_prepare_enable(rps->clk)))
+	ret = clk_prepare_enable(rps->clk);
+	if (ret)
 		goto err_clk;
 
 	base = of_iomap(np, 0);
-	if (WARN_ON(!base))
+	if (!base) {
+		ret = -ENXIO;
 		goto err_clk_prepare;
+	}
 
 	rps->irq = irq_of_parse_and_map(np, 0);
-	if (WARN_ON(rps->irq < 0))
+	if (rps->irq < 0) {
+		ret = -EINVAL;
 		goto err_iomap;
+	}
 
 	rps->clkevt_base = base + TIMER1_REG_OFFSET;
 	rps->clksrc_base = base + TIMER2_REG_OFFSET;
@@ -261,7 +266,7 @@ static void __init oxnas_rps_timer_init(struct device_node *np)
 	ret = request_irq(rps->irq, oxnas_rps_timer_irq,
 			  IRQF_TIMER | IRQF_IRQPOLL,
 			  "rps-timer", rps);
-	if (WARN_ON(ret))
+	if (ret)
 		goto err_iomap;
 
 	ret = oxnas_rps_clocksource_init(rps);
@@ -272,7 +277,7 @@ static void __init oxnas_rps_timer_init(struct device_node *np)
 	if (ret)
 		goto err_irqreq;
 
-	return;
+	return 0;
 
 err_irqreq:
 	free_irq(rps->irq, rps);
@@ -284,7 +289,9 @@ err_clk:
 	clk_put(rps->clk);
 err_alloc:
 	kfree(rps);
+
+	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE(ox810se_rps,
-		       "oxsemi,ox810se-rps-timer", oxnas_rps_timer_init);
+CLOCKSOURCE_OF_DECLARE_RET(ox810se_rps,
+			   "oxsemi,ox810se-rps-timer", oxnas_rps_timer_init);
Signature · 1 line
1.9.1
Acked-by on v2 62/63
#110 lore raw

Re: [PATCH V2 62/63] clocksource/drivers/oxnas-rps: Convert init function to return error

Quoted 12 lines · Daniel Lezcano

The init functions do not return any error. They behave as the following:

- panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly

or

- print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype.

Quoted 8 lines

Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function.

---
 drivers/clocksource/timer-oxnas-rps.c | 33 ++++++++++++++++++++-------------
 1 file changed, 20 insertions(+), 13 deletions(-)

Thanks,
Neil

#111 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 arch/arc/kernel/time.c                    |  6 +++---
 arch/arm/kernel/smp_twd.c                 |  6 +++---
 arch/microblaze/kernel/timer.c            |  2 +-
 arch/mips/ralink/cevt-rt3352.c            |  2 +-
 arch/nios2/kernel/time.c                  |  2 +-
 drivers/clocksource/arm_arch_timer.c      |  6 +++---
 drivers/clocksource/arm_global_timer.c    |  2 +-
 drivers/clocksource/armv7m_systick.c      |  2 +-
 drivers/clocksource/asm9260_timer.c       |  2 +-
 drivers/clocksource/bcm2835_timer.c       |  2 +-
 drivers/clocksource/bcm_kona_timer.c      |  4 ++--
 drivers/clocksource/cadence_ttc_timer.c   |  2 +-
 drivers/clocksource/clksrc-dbx500-prcmu.c |  2 +-
 drivers/clocksource/clksrc-probe.c        | 14 --------------
 drivers/clocksource/clksrc_st_lpc.c       |  2 +-
 drivers/clocksource/clps711x-timer.c      |  2 +-
 drivers/clocksource/dw_apb_timer_of.c     |  8 ++++----
 drivers/clocksource/exynos_mct.c          |  4 ++--
 drivers/clocksource/fsl_ftm_timer.c       |  2 +-
 drivers/clocksource/h8300_timer16.c       |  2 +-
 drivers/clocksource/h8300_timer8.c        |  2 +-
 drivers/clocksource/h8300_tpu.c           |  2 +-
 drivers/clocksource/meson6_timer.c        |  2 +-
 drivers/clocksource/mips-gic-timer.c      |  2 +-
 drivers/clocksource/moxart_timer.c        |  2 +-
 drivers/clocksource/mps2-timer.c          |  2 +-
 drivers/clocksource/mtk_timer.c           |  2 +-
 drivers/clocksource/mxs_timer.c           |  2 +-
 drivers/clocksource/nomadik-mtu.c         |  2 +-
 drivers/clocksource/pxa_timer.c           |  2 +-
 drivers/clocksource/qcom-timer.c          |  4 ++--
 drivers/clocksource/rockchip_timer.c      |  8 ++++----
 drivers/clocksource/samsung_pwm_timer.c   |  8 ++++----
 drivers/clocksource/sun4i_timer.c         |  2 +-
 drivers/clocksource/tango_xtal.c          |  2 +-
 drivers/clocksource/tegra20_timer.c       |  4 ++--
 drivers/clocksource/time-armada-370-xp.c  |  6 +++---
 drivers/clocksource/time-efm32.c          |  4 ++--
 drivers/clocksource/time-lpc32xx.c        |  2 +-
 drivers/clocksource/time-orion.c          |  2 +-
 drivers/clocksource/time-pistachio.c      |  2 +-
 drivers/clocksource/timer-atlas7.c        |  2 +-
 drivers/clocksource/timer-atmel-pit.c     |  2 +-
 drivers/clocksource/timer-atmel-st.c      |  2 +-
 drivers/clocksource/timer-digicolor.c     |  2 +-
 drivers/clocksource/timer-imx-gpt.c       | 24 ++++++++++++------------
 drivers/clocksource/timer-integrator-ap.c |  2 +-
 drivers/clocksource/timer-keystone.c      |  2 +-
 drivers/clocksource/timer-nps.c           |  4 ++--
 drivers/clocksource/timer-oxnas-rps.c     |  4 ++--
 drivers/clocksource/timer-prima2.c        |  2 +-
 drivers/clocksource/timer-sp804.c         |  4 ++--
 drivers/clocksource/timer-stm32.c         |  2 +-
 drivers/clocksource/timer-sun5i.c         |  4 ++--
 drivers/clocksource/timer-ti-32k.c        |  2 +-
 drivers/clocksource/timer-u300.c          |  2 +-
 drivers/clocksource/versatile.c           |  4 ++--
 drivers/clocksource/vf_pit_timer.c        |  2 +-
 drivers/clocksource/vt8500_timer.c        |  2 +-
 drivers/clocksource/zevio-timer.c         |  2 +-
 include/asm-generic/vmlinux.lds.h         |  2 --
 include/linux/clocksource.h               |  5 +----
 62 files changed, 98 insertions(+), 117 deletions(-)
arch/arc/kernel/time.c +3 -3
index 36110cd..ee00f2f 100644
@@ -130,7 +130,7 @@ static int __init arc_cs_setup_gfrc(struct device_node *node)
 
 	return clocksource_register_hz(&arc_counter_gfrc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
+CLOCKSOURCE_OF_DECLARE(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
 
 #endif
 
@@ -192,7 +192,7 @@ static int __init arc_cs_setup_rtc(struct device_node *node)
 
 	return clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
+CLOCKSOURCE_OF_DECLARE(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
 
 #endif
 
@@ -379,7 +379,7 @@ static int __init arc_of_timer_init(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(arc_clkevt, "snps,arc-timer", arc_of_timer_init);
+CLOCKSOURCE_OF_DECLARE(arc_clkevt, "snps,arc-timer", arc_of_timer_init);
 
 /*
  * Called from start_kernel() - boot CPU only
arch/arm/kernel/smp_twd.c +3 -3
index 2b24be4..b6ec65e 100644
@@ -412,7 +412,7 @@ out:
 	WARN(err, "twd_local_timer_of_register failed (%d)\n", err);
 	return err;
 }
-CLOCKSOURCE_OF_DECLARE_RET(arm_twd_a9, "arm,cortex-a9-twd-timer", twd_local_timer_of_register);
-CLOCKSOURCE_OF_DECLARE_RET(arm_twd_a5, "arm,cortex-a5-twd-timer", twd_local_timer_of_register);
-CLOCKSOURCE_OF_DECLARE_RET(arm_twd_11mp, "arm,arm11mp-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE(arm_twd_a9, "arm,cortex-a9-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE(arm_twd_a5, "arm,cortex-a5-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE(arm_twd_11mp, "arm,arm11mp-twd-timer", twd_local_timer_of_register);
 #endif
arch/microblaze/kernel/timer.c +1 -1
index 7f35e7b..5bbf38b 100644
@@ -332,5 +332,5 @@ static int __init xilinx_timer_init(struct device_node *timer)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(xilinx_timer, "xlnx,xps-timer-1.00.a",
+CLOCKSOURCE_OF_DECLARE(xilinx_timer, "xlnx,xps-timer-1.00.a",
 		       xilinx_timer_init);
arch/mips/ralink/cevt-rt3352.c +1 -1
index f2d3c79..f24eee0 100644
@@ -150,4 +150,4 @@ static int __init ralink_systick_init(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(systick, "ralink,cevt-systick", ralink_systick_init);
+CLOCKSOURCE_OF_DECLARE(systick, "ralink,cevt-systick", ralink_systick_init);
arch/nios2/kernel/time.c +1 -1
index 9fa7739..f337eef 100644
@@ -354,4 +354,4 @@ void __init time_init(void)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(nios2_timer, ALTR_TIMER_COMPATIBLE, nios2_time_init);
+CLOCKSOURCE_OF_DECLARE(nios2_timer, ALTR_TIMER_COMPATIBLE, nios2_time_init);
drivers/clocksource/arm_arch_timer.c +3 -3
index d0cda68..9e33309 100644
@@ -784,8 +784,8 @@ static int __init arch_timer_of_init(struct device_node *np)
 
 	return arch_timer_init();
 }
-CLOCKSOURCE_OF_DECLARE_RET(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
-CLOCKSOURCE_OF_DECLARE_RET(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
+CLOCKSOURCE_OF_DECLARE(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
+CLOCKSOURCE_OF_DECLARE(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
 
 static int __init arch_timer_mem_init(struct device_node *np)
 {
@@ -868,7 +868,7 @@ out:
 	of_node_put(best_frame);
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(armv7_arch_timer_mem, "arm,armv7-timer-mem",
+CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
 		       arch_timer_mem_init);
 
 #ifdef CONFIG_ACPI
drivers/clocksource/arm_global_timer.c +1 -1
index 40104fc..2a9ceb6 100644
@@ -358,5 +358,5 @@ out_unmap:
 }
 
 /* Only tested on r2p2 and r3p0  */
-CLOCKSOURCE_OF_DECLARE_RET(arm_gt, "arm,cortex-a9-global-timer",
+CLOCKSOURCE_OF_DECLARE(arm_gt, "arm,cortex-a9-global-timer",
 			global_timer_of_register);
drivers/clocksource/armv7m_systick.c +1 -1
index 2b55410..e93af1f 100644
@@ -81,5 +81,5 @@ out_unmap:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(arm_systick, "arm,armv7m-systick",
+CLOCKSOURCE_OF_DECLARE(arm_systick, "arm,armv7m-systick",
 			system_timer_of_register);
drivers/clocksource/asm9260_timer.c +1 -1
index d113c02..1ba871b 100644
@@ -238,5 +238,5 @@ static int __init asm9260_timer_init(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(asm9260_timer, "alphascale,asm9260-timer",
+CLOCKSOURCE_OF_DECLARE(asm9260_timer, "alphascale,asm9260-timer",
 		asm9260_timer_init);
drivers/clocksource/bcm2835_timer.c +1 -1
index 2dcf896..e71acf2 100644
@@ -142,5 +142,5 @@ static int __init bcm2835_timer_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(bcm2835, "brcm,bcm2835-system-timer",
+CLOCKSOURCE_OF_DECLARE(bcm2835, "brcm,bcm2835-system-timer",
 			bcm2835_timer_init);
drivers/clocksource/bcm_kona_timer.c +2 -2
index 98bc2a2..ee07e7e3 100644
@@ -200,9 +200,9 @@ static int __init kona_timer_init(struct device_node *node)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(brcm_kona, "brcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE(brcm_kona, "brcm,kona-timer", kona_timer_init);
 /*
  * bcm,kona-timer is deprecated by brcm,kona-timer
  * being kept here for driver compatibility
  */
-CLOCKSOURCE_OF_DECLARE_RET(bcm_kona, "bcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);
drivers/clocksource/cadence_ttc_timer.c +1 -1
index e2e7631..388a77b 100644
@@ -539,4 +539,4 @@ static int __init ttc_timer_init(struct device_node *timer)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(ttc, "cdns,ttc", ttc_timer_init);
+CLOCKSOURCE_OF_DECLARE(ttc, "cdns,ttc", ttc_timer_init);
drivers/clocksource/clksrc-dbx500-prcmu.c +1 -1
index 5a59d29..77a365f 100644
@@ -86,5 +86,5 @@ static int __init clksrc_dbx500_prcmu_init(struct device_node *node)
 #endif
 	return clocksource_register_hz(&clocksource_dbx500_prcmu, RATE_32K);
 }
-CLOCKSOURCE_OF_DECLARE_RET(dbx500_prcmu, "stericsson,db8500-prcmu-timer-4",
+CLOCKSOURCE_OF_DECLARE(dbx500_prcmu, "stericsson,db8500-prcmu-timer-4",
 		       clksrc_dbx500_prcmu_init);
drivers/clocksource/clksrc-probe.c +0 -14
index 5fa6a55..bc62be9 100644
@@ -20,19 +20,14 @@
 #include <linux/clocksource.h>
 
 extern struct of_device_id __clksrc_of_table[];
-extern struct of_device_id __clksrc_ret_of_table[];
 
 static const struct of_device_id __clksrc_of_table_sentinel
 	__used __section(__clksrc_of_table_end);
 
-static const struct of_device_id __clksrc_ret_of_table_sentinel
-	__used __section(__clksrc_ret_of_table_end);
-
 void __init clocksource_probe(void)
 {
 	struct device_node *np;
 	const struct of_device_id *match;
-	of_init_fn_1 init_func;
 	of_init_fn_1_ret init_func_ret;
 	unsigned clocksources = 0;
 	int ret;
@@ -41,15 +36,6 @@ void __init clocksource_probe(void)
 		if (!of_device_is_available(np))
 			continue;
 
-		init_func = match->data;
-		init_func(np);
-		clocksources++;
-	}
-
-	for_each_matching_node_and_match(np, __clksrc_ret_of_table, &match) {
-		if (!of_device_is_available(np))
-			continue;
-
 		init_func_ret = match->data;
 
 		ret = init_func_ret(np);
drivers/clocksource/clksrc_st_lpc.c +1 -1
index c9022a9..03cc492 100644
@@ -132,4 +132,4 @@ static int __init st_clksrc_of_register(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(ddata, "st,stih407-lpc", st_clksrc_of_register);
+CLOCKSOURCE_OF_DECLARE(ddata, "st,stih407-lpc", st_clksrc_of_register);
drivers/clocksource/clps711x-timer.c +1 -1
index 3b66198..84aed78 100644
@@ -119,5 +119,5 @@ static int __init clps711x_timer_init(struct device_node *np)
 		return -EINVAL;
 	}
 }
-CLOCKSOURCE_OF_DECLARE_RET(clps711x, "cirrus,clps711x-timer", clps711x_timer_init);
+CLOCKSOURCE_OF_DECLARE(clps711x, "cirrus,clps711x-timer", clps711x_timer_init);
 #endif
drivers/clocksource/dw_apb_timer_of.c +4 -4
index 4985a2c..aee6c0d 100644
@@ -167,7 +167,7 @@ static int __init dw_apb_timer_init(struct device_node *timer)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(pc3x2_timer, "picochip,pc3x2-timer", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(apb_timer_osc, "snps,dw-apb-timer-osc", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(apb_timer_sp, "snps,dw-apb-timer-sp", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(apb_timer, "snps,dw-apb-timer", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE(pc3x2_timer, "picochip,pc3x2-timer", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE(apb_timer_osc, "snps,dw-apb-timer-osc", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE(apb_timer_sp, "snps,dw-apb-timer-sp", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE(apb_timer, "snps,dw-apb-timer", dw_apb_timer_init);
drivers/clocksource/exynos_mct.c +2 -2
index f6caed0..0d18dd4b 100644
@@ -627,5 +627,5 @@ static int __init mct_init_ppi(struct device_node *np)
 {
 	return mct_init_dt(np, MCT_INT_PPI);
 }
-CLOCKSOURCE_OF_DECLARE_RET(exynos4210, "samsung,exynos4210-mct", mct_init_spi);
-CLOCKSOURCE_OF_DECLARE_RET(exynos4412, "samsung,exynos4412-mct", mct_init_ppi);
+CLOCKSOURCE_OF_DECLARE(exynos4210, "samsung,exynos4210-mct", mct_init_spi);
+CLOCKSOURCE_OF_DECLARE(exynos4412, "samsung,exynos4412-mct", mct_init_ppi);
drivers/clocksource/fsl_ftm_timer.c +1 -1
index 9ad4ca3..738515b 100644
@@ -369,4 +369,4 @@ err:
 	kfree(priv);
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(flextimer, "fsl,ftm-timer", ftm_timer_init);
+CLOCKSOURCE_OF_DECLARE(flextimer, "fsl,ftm-timer", ftm_timer_init);
drivers/clocksource/h8300_timer16.c +1 -1
index 9d99fc8..07d9d5b 100644
@@ -187,5 +187,5 @@ free_clk:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(h8300_16bit, "renesas,16bit-timer",
+CLOCKSOURCE_OF_DECLARE(h8300_16bit, "renesas,16bit-timer",
 			   h8300_16timer_init);
drivers/clocksource/h8300_timer8.c +1 -1
index 0292a19..546bb18 100644
@@ -215,4 +215,4 @@ free_clk:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(h8300_8bit, "renesas,8bit-timer", h8300_8timer_init);
+CLOCKSOURCE_OF_DECLARE(h8300_8bit, "renesas,8bit-timer", h8300_8timer_init);
drivers/clocksource/h8300_tpu.c +1 -1
index 4faf718..7bdf199 100644
@@ -154,4 +154,4 @@ free_clk:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(h8300_tpu, "renesas,tpu", h8300_tpu_init);
+CLOCKSOURCE_OF_DECLARE(h8300_tpu, "renesas,tpu", h8300_tpu_init);
drivers/clocksource/meson6_timer.c +1 -1
index 3a6e78f..52af591 100644
@@ -174,5 +174,5 @@ static int __init meson6_timer_init(struct device_node *node)
 					1, 0xfffe);
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(meson6, "amlogic,meson6-timer",
+CLOCKSOURCE_OF_DECLARE(meson6, "amlogic,meson6-timer",
 		       meson6_timer_init);
drivers/clocksource/mips-gic-timer.c +1 -1
index b164b87..1572c7a 100644
@@ -222,5 +222,5 @@ static void __init gic_clocksource_of_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(mips_gic_timer, "mti,gic-timer",
+CLOCKSOURCE_OF_DECLARE(mips_gic_timer, "mti,gic-timer",
 		       gic_clocksource_of_init);
drivers/clocksource/moxart_timer.c +1 -1
index b9c30cd..8414544 100644
@@ -178,4 +178,4 @@ static int __init moxart_timer_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(moxart, "moxa,moxart-timer", moxart_timer_init);
+CLOCKSOURCE_OF_DECLARE(moxart, "moxa,moxart-timer", moxart_timer_init);
drivers/clocksource/mps2-timer.c +1 -1
index c303fa9..3e4431e 100644
@@ -274,4 +274,4 @@ static int __init mps2_timer_init(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(mps2_timer, "arm,mps2-timer", mps2_timer_init);
+CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);
drivers/clocksource/mtk_timer.c +1 -1
index 432a2c0..9065949 100644
@@ -265,4 +265,4 @@ err_kzalloc:
 
 	return -EINVAL;
 }
-CLOCKSOURCE_OF_DECLARE_RET(mtk_mt6577, "mediatek,mt6577-timer", mtk_timer_init);
+CLOCKSOURCE_OF_DECLARE(mtk_mt6577, "mediatek,mt6577-timer", mtk_timer_init);
drivers/clocksource/mxs_timer.c +1 -1
index 17b9d19..630a8d3 100644
@@ -295,4 +295,4 @@ static int __init mxs_timer_init(struct device_node *np)
 
 	return setup_irq(irq, &mxs_timer_irq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(mxs, "fsl,timrot", mxs_timer_init);
+CLOCKSOURCE_OF_DECLARE(mxs, "fsl,timrot", mxs_timer_init);
drivers/clocksource/nomadik-mtu.c +1 -1
index d2be5b3..3c124d1 100644
@@ -284,5 +284,5 @@ static int __init nmdk_timer_of_init(struct device_node *node)
 
 	return nmdk_timer_init(base, irq, pclk, clk);
 }
-CLOCKSOURCE_OF_DECLARE_RET(nomadik_mtu, "st,nomadik-mtu",
+CLOCKSOURCE_OF_DECLARE(nomadik_mtu, "st,nomadik-mtu",
 		       nmdk_timer_of_init);
drivers/clocksource/pxa_timer.c +1 -1
index 59af75c..937e10b 100644
@@ -213,7 +213,7 @@ static int __init pxa_timer_dt_init(struct device_node *np)
 
 	return pxa_timer_common_init(irq, clk_get_rate(clk));
 }
-CLOCKSOURCE_OF_DECLARE_RET(pxa_timer, "marvell,pxa-timer", pxa_timer_dt_init);
+CLOCKSOURCE_OF_DECLARE(pxa_timer, "marvell,pxa-timer", pxa_timer_dt_init);
 
 /*
  * Legacy timer init for non device-tree boards.
drivers/clocksource/qcom-timer.c +2 -2
index 79f73bd..6625763 100644
@@ -273,5 +273,5 @@ static int __init msm_dt_timer_init(struct device_node *np)
 
 	return msm_timer_init(freq, 32, irq, !!percpu_offset);
 }
-CLOCKSOURCE_OF_DECLARE_RET(kpss_timer, "qcom,kpss-timer", msm_dt_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(scss_timer, "qcom,scss-timer", msm_dt_timer_init);
+CLOCKSOURCE_OF_DECLARE(kpss_timer, "qcom,kpss-timer", msm_dt_timer_init);
+CLOCKSOURCE_OF_DECLARE(scss_timer, "qcom,scss-timer", msm_dt_timer_init);
drivers/clocksource/rockchip_timer.c +4 -4
index d10bdee..d10e7a5 100644
@@ -200,7 +200,7 @@ static int __init rk3399_timer_init(struct device_node *np)
 	return rk_timer_init(np, TIMER_CONTROL_REG3399);
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(rk3288_timer, "rockchip,rk3288-timer",
-			   rk3288_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(rk3399_timer, "rockchip,rk3399-timer",
-			   rk3399_timer_init);
+CLOCKSOURCE_OF_DECLARE(rk3288_timer, "rockchip,rk3288-timer",
+		       rk3288_timer_init);
+CLOCKSOURCE_OF_DECLARE(rk3399_timer, "rockchip,rk3399-timer",
+		       rk3399_timer_init);
drivers/clocksource/samsung_pwm_timer.c +4 -4
index 27a9797..54565bd 100644
@@ -466,7 +466,7 @@ static int __init s3c2410_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s3c24xx_variant);
 }
-CLOCKSOURCE_OF_DECLARE_RET(s3c2410_pwm, "samsung,s3c2410-pwm", s3c2410_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(s3c2410_pwm, "samsung,s3c2410-pwm", s3c2410_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s3c64xx_variant = {
 	.bits		= 32,
@@ -479,7 +479,7 @@ static int __init s3c64xx_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s3c64xx_variant);
 }
-CLOCKSOURCE_OF_DECLARE_RET(s3c6400_pwm, "samsung,s3c6400-pwm", s3c64xx_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(s3c6400_pwm, "samsung,s3c6400-pwm", s3c64xx_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s5p64x0_variant = {
 	.bits		= 32,
@@ -492,7 +492,7 @@ static int __init s5p64x0_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s5p64x0_variant);
 }
-CLOCKSOURCE_OF_DECLARE_RET(s5p6440_pwm, "samsung,s5p6440-pwm", s5p64x0_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(s5p6440_pwm, "samsung,s5p6440-pwm", s5p64x0_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s5p_variant = {
 	.bits		= 32,
@@ -505,5 +505,5 @@ static int __init s5p_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s5p_variant);
 }
-CLOCKSOURCE_OF_DECLARE_RET(s5pc100_pwm, "samsung,s5pc100-pwm", s5p_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(s5pc100_pwm, "samsung,s5pc100-pwm", s5p_pwm_clocksource_init);
 #endif
drivers/clocksource/sun4i_timer.c +1 -1
index 4453730..97669ee 100644
@@ -226,5 +226,5 @@ static int __init sun4i_timer_init(struct device_node *node)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(sun4i, "allwinner,sun4i-a10-timer",
+CLOCKSOURCE_OF_DECLARE(sun4i, "allwinner,sun4i-a10-timer",
 		       sun4i_timer_init);
drivers/clocksource/tango_xtal.c +1 -1
index 7dc716c..12fcef8 100644
@@ -53,4 +53,4 @@ static int __init tango_clocksource_init(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(tango, "sigma,tick-counter", tango_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(tango, "sigma,tick-counter", tango_clocksource_init);
drivers/clocksource/tegra20_timer.c +2 -2
index 543c37e..f960891 100644
@@ -237,7 +237,7 @@ static int __init tegra20_init_timer(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(tegra20_timer, "nvidia,tegra20-timer", tegra20_init_timer);
+CLOCKSOURCE_OF_DECLARE(tegra20_timer, "nvidia,tegra20-timer", tegra20_init_timer);
 
 static int __init tegra20_init_rtc(struct device_node *np)
 {
@@ -261,4 +261,4 @@ static int __init tegra20_init_rtc(struct device_node *np)
 
 	return register_persistent_clock(NULL, tegra_read_persistent_clock64);
 }
-CLOCKSOURCE_OF_DECLARE_RET(tegra20_rtc, "nvidia,tegra20-rtc", tegra20_init_rtc);
+CLOCKSOURCE_OF_DECLARE(tegra20_rtc, "nvidia,tegra20-rtc", tegra20_init_rtc);
drivers/clocksource/time-armada-370-xp.c +3 -3
index bc4ab48..a4e5923 100644
@@ -371,7 +371,7 @@ static int __init armada_xp_timer_init(struct device_node *np)
 
 	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE_RET(armada_xp, "marvell,armada-xp-timer",
+CLOCKSOURCE_OF_DECLARE(armada_xp, "marvell,armada-xp-timer",
 		       armada_xp_timer_init);
 
 static int __init armada_375_timer_init(struct device_node *np)
@@ -409,7 +409,7 @@ static int __init armada_375_timer_init(struct device_node *np)
 
 	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE_RET(armada_375, "marvell,armada-375-timer",
+CLOCKSOURCE_OF_DECLARE(armada_375, "marvell,armada-375-timer",
 		       armada_375_timer_init);
 
 static int __init armada_370_timer_init(struct device_node *np)
@@ -432,5 +432,5 @@ static int __init armada_370_timer_init(struct device_node *np)
 
 	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE_RET(armada_370, "marvell,armada-370-timer",
+CLOCKSOURCE_OF_DECLARE(armada_370, "marvell,armada-370-timer",
 		       armada_370_timer_init);
drivers/clocksource/time-efm32.c +2 -2
index b71ffc6..10a0521 100644
@@ -282,5 +282,5 @@ static int __init efm32_timer_init(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(efm32compat, "efm32,timer", efm32_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(efm32, "energymicro,efm32-timer", efm32_timer_init);
+CLOCKSOURCE_OF_DECLARE(efm32compat, "efm32,timer", efm32_timer_init);
+CLOCKSOURCE_OF_DECLARE(efm32, "energymicro,efm32-timer", efm32_timer_init);
drivers/clocksource/time-lpc32xx.c +1 -1
index cb5b866..9649cfd 100644
@@ -311,4 +311,4 @@ static int __init lpc32xx_timer_init(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(lpc32xx_timer, "nxp,lpc3220-timer", lpc32xx_timer_init);
+CLOCKSOURCE_OF_DECLARE(lpc32xx_timer, "nxp,lpc3220-timer", lpc32xx_timer_init);
drivers/clocksource/time-orion.c +1 -1
index 5fdeb5d..a28f496 100644
@@ -167,4 +167,4 @@ static int __init orion_timer_init(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(orion_timer, "marvell,orion-timer", orion_timer_init);
+CLOCKSOURCE_OF_DECLARE(orion_timer, "marvell,orion-timer", orion_timer_init);
drivers/clocksource/time-pistachio.c +1 -1
index adaaec5..a7d9a08 100644
@@ -214,5 +214,5 @@ static int __init pistachio_clksrc_of_init(struct device_node *node)
 	sched_clock_register(pistachio_read_sched_clock, 32, rate);
 	return clocksource_register_hz(&pcs_gpt.cs, rate);
 }
-CLOCKSOURCE_OF_DECLARE_RET(pistachio_gptimer, "img,pistachio-gptimer",
+CLOCKSOURCE_OF_DECLARE(pistachio_gptimer, "img,pistachio-gptimer",
 		       pistachio_clksrc_of_init);
drivers/clocksource/timer-atlas7.c +1 -1
index 7b1a007..90f8fbc 100644
@@ -304,4 +304,4 @@ static int __init sirfsoc_of_timer_init(struct device_node *np)
 
 	return sirfsoc_atlas7_timer_init(np);
 }
-CLOCKSOURCE_OF_DECLARE_RET(sirfsoc_atlas7_timer, "sirf,atlas7-tick", sirfsoc_of_timer_init);
+CLOCKSOURCE_OF_DECLARE(sirfsoc_atlas7_timer, "sirf,atlas7-tick", sirfsoc_of_timer_init);
drivers/clocksource/timer-atmel-pit.c +1 -1
index ffaca7c..1ffac0c 100644
@@ -270,5 +270,5 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
 
 	return at91sam926x_pit_common_init(data);
 }
-CLOCKSOURCE_OF_DECLARE_RET(at91sam926x_pit, "atmel,at91sam9260-pit",
+CLOCKSOURCE_OF_DECLARE(at91sam926x_pit, "atmel,at91sam9260-pit",
 		       at91sam926x_pit_dt_init);
drivers/clocksource/timer-atmel-st.c +1 -1
index e9331d3..e90ab5b 100644
@@ -260,5 +260,5 @@ static int __init atmel_st_timer_init(struct device_node *node)
 	/* register clocksource */
 	return clocksource_register_hz(&clk32k, sclk_rate);
 }
-CLOCKSOURCE_OF_DECLARE_RET(atmel_st_timer, "atmel,at91rm9200-st",
+CLOCKSOURCE_OF_DECLARE(atmel_st_timer, "atmel,at91rm9200-st",
 		       atmel_st_timer_init);
drivers/clocksource/timer-digicolor.c +1 -1
index b929061..10318cc 100644
@@ -202,5 +202,5 @@ static int __init digicolor_timer_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(conexant_digicolor, "cnxt,cx92755-timer",
+CLOCKSOURCE_OF_DECLARE(conexant_digicolor, "cnxt,cx92755-timer",
 		       digicolor_timer_init);
drivers/clocksource/timer-imx-gpt.c +12 -12
index d5640a74..f595460 100644
@@ -545,15 +545,15 @@ static int __init imx6dl_timer_init_dt(struct device_node *np)
 	return mxc_timer_init_dt(np, GPT_TYPE_IMX6DL);
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(imx1_timer, "fsl,imx1-gpt", imx1_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx21_timer, "fsl,imx21-gpt", imx21_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx27_timer, "fsl,imx27-gpt", imx21_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx31_timer, "fsl,imx31-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx25_timer, "fsl,imx25-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx50_timer, "fsl,imx50-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx51_timer, "fsl,imx51-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx53_timer, "fsl,imx53-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx6q_timer, "fsl,imx6q-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx6dl_timer, "fsl,imx6dl-gpt", imx6dl_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx6sl_timer, "fsl,imx6sl-gpt", imx6dl_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx1_timer, "fsl,imx1-gpt", imx1_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx21_timer, "fsl,imx21-gpt", imx21_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx27_timer, "fsl,imx27-gpt", imx21_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx31_timer, "fsl,imx31-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx25_timer, "fsl,imx25-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx50_timer, "fsl,imx50-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx51_timer, "fsl,imx51-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx53_timer, "fsl,imx53-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx6q_timer, "fsl,imx6q-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx6dl_timer, "fsl,imx6dl-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx6sl_timer, "fsl,imx6sl-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
drivers/clocksource/timer-integrator-ap.c +1 -1
index 675face..df6e672 100644
@@ -232,5 +232,5 @@ static int __init integrator_ap_timer_init_of(struct device_node *node)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(integrator_ap_timer, "arm,integrator-timer",
+CLOCKSOURCE_OF_DECLARE(integrator_ap_timer, "arm,integrator-timer",
 		       integrator_ap_timer_init_of);
drivers/clocksource/timer-keystone.c +1 -1
index 4199823..ab68a47 100644
@@ -226,5 +226,5 @@ err:
 	return error;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(keystone_timer, "ti,keystone-timer",
+CLOCKSOURCE_OF_DECLARE(keystone_timer, "ti,keystone-timer",
 			   keystone_timer_init);
drivers/clocksource/timer-nps.c +2 -2
index b5c7b2b..70c149a 100644
@@ -96,5 +96,5 @@ static int __init nps_timer_init(struct device_node *node)
 	return nps_setup_clocksource(node, clk);
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(ezchip_nps400_clksrc, "ezchip,nps400-timer",
-			   nps_timer_init);
+CLOCKSOURCE_OF_DECLARE(ezchip_nps400_clksrc, "ezchip,nps400-timer",
+		       nps_timer_init);
drivers/clocksource/timer-oxnas-rps.c +2 -2
index 0d99f40..bd887e2 100644
@@ -293,5 +293,5 @@ err_alloc:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(ox810se_rps,
-			   "oxsemi,ox810se-rps-timer", oxnas_rps_timer_init);
+CLOCKSOURCE_OF_DECLARE(ox810se_rps,
+		       "oxsemi,ox810se-rps-timer", oxnas_rps_timer_init);
drivers/clocksource/timer-prima2.c +1 -1
index 7b1084d..dae8a66 100644
@@ -246,5 +246,5 @@ static int __init sirfsoc_prima2_timer_init(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(sirfsoc_prima2_timer,
+CLOCKSOURCE_OF_DECLARE(sirfsoc_prima2_timer,
 	"sirf,prima2-tick", sirfsoc_prima2_timer_init);
drivers/clocksource/timer-sp804.c +2 -2
index 7c2944ad..a2b28da 100644
@@ -287,7 +287,7 @@ err:
 	iounmap(base);
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(sp804, "arm,sp804", sp804_of_init);
+CLOCKSOURCE_OF_DECLARE(sp804, "arm,sp804", sp804_of_init);
 
 static int __init integrator_cp_of_init(struct device_node *np)
 {
@@ -336,4 +336,4 @@ err:
 	iounmap(base);
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(intcp, "arm,integrator-cp-timer", integrator_cp_of_init);
+CLOCKSOURCE_OF_DECLARE(intcp, "arm,integrator-cp-timer", integrator_cp_of_init);
drivers/clocksource/timer-stm32.c +1 -1
index d5bf352..1b2574c 100644
@@ -187,4 +187,4 @@ err_clk_get:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(stm32, "st,stm32-timer", stm32_clockevent_init);
+CLOCKSOURCE_OF_DECLARE(stm32, "st,stm32-timer", stm32_clockevent_init);
drivers/clocksource/timer-sun5i.c +2 -2
index f0a3ffb..c184eb8 100644
@@ -346,7 +346,7 @@ static int __init sun5i_timer_init(struct device_node *node)
 
 	return sun5i_setup_clockevent(node, timer_base, clk, irq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(sun5i_a13, "allwinner,sun5i-a13-hstimer",
+CLOCKSOURCE_OF_DECLARE(sun5i_a13, "allwinner,sun5i-a13-hstimer",
 			   sun5i_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(sun7i_a20, "allwinner,sun7i-a20-hstimer",
+CLOCKSOURCE_OF_DECLARE(sun7i_a20, "allwinner,sun7i-a20-hstimer",
 			   sun5i_timer_init);
drivers/clocksource/timer-ti-32k.c +1 -1
index e4ad3c6e..92b7e39 100644
@@ -124,5 +124,5 @@ static int __init ti_32k_timer_init(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(ti_32k_timer, "ti,omap-counter32k",
+CLOCKSOURCE_OF_DECLARE(ti_32k_timer, "ti,omap-counter32k",
 		ti_32k_timer_init);
drivers/clocksource/timer-u300.c +1 -1
index a6a0dec..704e40c 100644
@@ -458,5 +458,5 @@ static int __init u300_timer_init_of(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(u300_timer, "stericsson,u300-apptimer",
+CLOCKSOURCE_OF_DECLARE(u300_timer, "stericsson,u300-apptimer",
 		       u300_timer_init_of);
drivers/clocksource/versatile.c +2 -2
index 8daeffa..220b490 100644
@@ -38,7 +38,7 @@ static int __init versatile_sched_clock_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(vexpress, "arm,vexpress-sysreg",
+CLOCKSOURCE_OF_DECLARE(vexpress, "arm,vexpress-sysreg",
 		       versatile_sched_clock_init);
-CLOCKSOURCE_OF_DECLARE_RET(versatile, "arm,versatile-sysreg",
+CLOCKSOURCE_OF_DECLARE(versatile, "arm,versatile-sysreg",
 		       versatile_sched_clock_init);
drivers/clocksource/vf_pit_timer.c +1 -1
index ca4dff4..55d8d84 100644
@@ -201,4 +201,4 @@ static int __init pit_timer_init(struct device_node *np)
 
 	return pit_clockevent_init(clk_rate, irq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(vf610, "fsl,vf610-pit", pit_timer_init);
+CLOCKSOURCE_OF_DECLARE(vf610, "fsl,vf610-pit", pit_timer_init);
drivers/clocksource/vt8500_timer.c +1 -1
index 1bc8707..b150694 100644
@@ -165,4 +165,4 @@ static int __init vt8500_timer_init(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(vt8500, "via,vt8500-timer", vt8500_timer_init);
+CLOCKSOURCE_OF_DECLARE(vt8500, "via,vt8500-timer", vt8500_timer_init);
drivers/clocksource/zevio-timer.c +1 -1
index cb4cf056..9a53f5e 100644
@@ -215,4 +215,4 @@ static int __init zevio_timer_init(struct device_node *node)
 	return zevio_timer_add(node);
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(zevio_timer, "lsi,zevio-timer", zevio_timer_init);
+CLOCKSOURCE_OF_DECLARE(zevio_timer, "lsi,zevio-timer", zevio_timer_init);
include/asm-generic/vmlinux.lds.h +0 -2
index 8c6c626..6a67ab9 100644
@@ -173,7 +173,6 @@
 	*(__##name##_of_table_end)
 
 #define CLKSRC_OF_TABLES()	OF_TABLE(CONFIG_CLKSRC_OF, clksrc)
-#define CLKSRC_RET_OF_TABLES()	OF_TABLE(CONFIG_CLKSRC_OF, clksrc_ret)
 #define IRQCHIP_OF_MATCH_TABLE() OF_TABLE(CONFIG_IRQCHIP, irqchip)
 #define CLK_OF_TABLES()		OF_TABLE(CONFIG_COMMON_CLK, clk)
 #define IOMMU_OF_TABLES()	OF_TABLE(CONFIG_OF_IOMMU, iommu)
@@ -532,7 +531,6 @@
 	CLK_OF_TABLES()							\
 	RESERVEDMEM_OF_TABLES()						\
 	CLKSRC_OF_TABLES()						\
-	CLKSRC_RET_OF_TABLES()						\
 	IOMMU_OF_TABLES()						\
 	CPU_METHOD_OF_TABLES()						\
 	CPUIDLE_METHOD_OF_TABLES()					\
include/linux/clocksource.h +1 -4
index 15c3839..0839818 100644
@@ -244,10 +244,7 @@ extern int clocksource_mmio_init(void __iomem *, const char *,
 extern int clocksource_i8253_init(void);
 
 #define CLOCKSOURCE_OF_DECLARE(name, compat, fn) \
-	OF_DECLARE_1(clksrc, name, compat, fn)
-
-#define CLOCKSOURCE_OF_DECLARE_RET(name, compat, fn) \
-	OF_DECLARE_1_RET(clksrc_ret, name, compat, fn)
+	OF_DECLARE_1_RET(clksrc, name, compat, fn)
 
 #ifdef CONFIG_CLKSRC_PROBE
 extern void clocksource_probe(void);
Signature · 1 line
1.9.1
#112 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

Quoted 35 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 arch/arc/kernel/time.c                    |  6 +++---
 arch/arm/kernel/smp_twd.c                 |  6 +++---
 arch/microblaze/kernel/timer.c            |  2 +-
 arch/mips/ralink/cevt-rt3352.c            |  2 +-
 arch/nios2/kernel/time.c                  |  2 +-
 drivers/clocksource/arm_arch_timer.c      |  6 +++---
 drivers/clocksource/arm_global_timer.c    |  2 +-
 drivers/clocksource/armv7m_systick.c      |  2 +-
 drivers/clocksource/asm9260_timer.c       |  2 +-
 drivers/clocksource/bcm2835_timer.c       |  2 +-
 drivers/clocksource/bcm_kona_timer.c      |  4 ++--
 drivers/clocksource/cadence_ttc_timer.c   |  2 +-
 drivers/clocksource/clksrc-dbx500-prcmu.c |  2 +-
 drivers/clocksource/clksrc-probe.c        | 14 --------------
 drivers/clocksource/clksrc_st_lpc.c       |  2 +-
 drivers/clocksource/clps711x-timer.c      |  2 +-
 drivers/clocksource/dw_apb_timer_of.c     |  8 ++++----
 drivers/clocksource/exynos_mct.c          |  4 ++--
 drivers/clocksource/fsl_ftm_timer.c       |  2 +-
 drivers/clocksource/h8300_timer16.c       |  2 +-
 drivers/clocksource/h8300_timer8.c        |  2 +-
 drivers/clocksource/h8300_tpu.c           |  2 +-
 drivers/clocksource/meson6_timer.c        |  2 +-
 drivers/clocksource/mips-gic-timer.c      |  2 +-
 drivers/clocksource/moxart_timer.c        |  2 +-
Quoted 8 lines
 drivers/clocksource/mps2-timer.c          |  2 +-
 drivers/clocksource/mtk_timer.c           |  2 +-
 drivers/clocksource/mxs_timer.c           |  2 +-
 drivers/clocksource/nomadik-mtu.c         |  2 +-
 drivers/clocksource/pxa_timer.c           |  2 +-
 drivers/clocksource/qcom-timer.c          |  4 ++--
 drivers/clocksource/rockchip_timer.c      |  8 ++++----
 drivers/clocksource/samsung_pwm_timer.c   |  8 ++++----

For exynos_mct and samsung_pwm_timer:

Best regards,
Krzysztof

Acked-by on v2 63/63
#113 lore raw

Re: [PATCH V2 63/63] clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 2 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE

s/CLOCKSOURCE_OF_DECLARE/CLOCKSOURCE_OF_DECLARE_RET

is no longer used as well as the

Quoted 9 lines

clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 arch/arc/kernel/time.c                    |  6 +++---

Thx,
-Vineet

#114 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 4 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Quoted 8 lines

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---

 drivers/clocksource/timer-keystone.c      |  2 +-
maintainer
#115 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 11 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
  arch/arc/kernel/time.c                    |  6 +++---

[...]

Quoted 1 line
  drivers/clocksource/mtk_timer.c           |  2 +-

For mediatek driver:

maintainer
#116 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano

Am Donnerstag, 16. Juni 2016, 23:27:22 schrieb Daniel Lezcano:

Quoted 19 lines

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 drivers/clocksource/rockchip_timer.c      |  8 ++++----

diff --git
a/drivers/clocksource/rockchip_timer.c b/drivers/clocksource/rockchip_timer.c index d10bdee..d10e7a5 100644

drivers/clocksource/rockchip_timer.c +0 -0
@@ -200,7 +200,7 @@ static int __init rk3399_timer_init(struct device_node
 *np) return rk_timer_init(np, TIMER_CONTROL_REG3399);

drivers/clocksource/rockchip_timer.c static int __init rk3399_timer_init(struct device_node · line 206

Quoted 10 lines
drivers/clocksource/rockchip_timer.c +4 -4
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(rk3288_timer, "rockchip,rk3288-timer",
-			   rk3288_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(rk3399_timer, "rockchip,rk3399-timer",
-			   rk3399_timer_init);
+CLOCKSOURCE_OF_DECLARE(rk3288_timer, "rockchip,rk3288-timer",
+		       rk3288_timer_init);
+CLOCKSOURCE_OF_DECLARE(rk3399_timer, "rockchip,rk3399-timer",
+		       rk3399_timer_init);

for the Rockchip-part

#117 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 16 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

  drivers/clocksource/clksrc_st_lpc.c       |  2 +-
drivers/clocksource/clksrc_st_lpc.c +0 -0
index c9022a9..03cc492 100644

drivers/clocksource/clksrc_st_lpc.c static int __init st_clksrc_of_register(struct device_node *np) · line 135

Quoted 5 lines
drivers/clocksource/clksrc_st_lpc.c +1 -1
@@ -132,4 +132,4 @@ static int __init st_clksrc_of_register(struct device_node *np)
 
  	return ret;
  }
-CLOCKSOURCE_OF_DECLARE_RET(ddata, "st,stih407-lpc", st_clksrc_of_register);
+CLOCKSOURCE_OF_DECLARE(ddata, "st,stih407-lpc", st_clksrc_of_register);

For STi :

Thanks

maintainer
#118 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 65 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 arch/arc/kernel/time.c                    |  6 +++---
 arch/arm/kernel/smp_twd.c                 |  6 +++---
 arch/microblaze/kernel/timer.c            |  2 +-
 arch/mips/ralink/cevt-rt3352.c            |  2 +-
 arch/nios2/kernel/time.c                  |  2 +-
 drivers/clocksource/arm_arch_timer.c      |  6 +++---
 drivers/clocksource/arm_global_timer.c    |  2 +-
 drivers/clocksource/armv7m_systick.c      |  2 +-
 drivers/clocksource/asm9260_timer.c       |  2 +-
 drivers/clocksource/bcm2835_timer.c       |  2 +-
 drivers/clocksource/bcm_kona_timer.c      |  4 ++--
 drivers/clocksource/cadence_ttc_timer.c   |  2 +-
 drivers/clocksource/clksrc-dbx500-prcmu.c |  2 +-
 drivers/clocksource/clksrc-probe.c        | 14 --------------
 drivers/clocksource/clksrc_st_lpc.c       |  2 +-
 drivers/clocksource/clps711x-timer.c      |  2 +-
 drivers/clocksource/dw_apb_timer_of.c     |  8 ++++----
 drivers/clocksource/exynos_mct.c          |  4 ++--
 drivers/clocksource/fsl_ftm_timer.c       |  2 +-
 drivers/clocksource/h8300_timer16.c       |  2 +-
 drivers/clocksource/h8300_timer8.c        |  2 +-
 drivers/clocksource/h8300_tpu.c           |  2 +-
 drivers/clocksource/meson6_timer.c        |  2 +-
 drivers/clocksource/mips-gic-timer.c      |  2 +-
 drivers/clocksource/moxart_timer.c        |  2 +-
 drivers/clocksource/mps2-timer.c          |  2 +-
 drivers/clocksource/mtk_timer.c           |  2 +-
 drivers/clocksource/mxs_timer.c           |  2 +-
 drivers/clocksource/nomadik-mtu.c         |  2 +-
 drivers/clocksource/pxa_timer.c           |  2 +-
 drivers/clocksource/qcom-timer.c          |  4 ++--
 drivers/clocksource/rockchip_timer.c      |  8 ++++----
 drivers/clocksource/samsung_pwm_timer.c   |  8 ++++----
 drivers/clocksource/sun4i_timer.c         |  2 +-
 drivers/clocksource/tango_xtal.c          |  2 +-
 drivers/clocksource/tegra20_timer.c       |  4 ++--
 drivers/clocksource/time-armada-370-xp.c  |  6 +++---
 drivers/clocksource/time-efm32.c          |  4 ++--
 drivers/clocksource/time-lpc32xx.c        |  2 +-
 drivers/clocksource/time-orion.c          |  2 +-
 drivers/clocksource/time-pistachio.c      |  2 +-
 drivers/clocksource/timer-atlas7.c        |  2 +-
 drivers/clocksource/timer-atmel-pit.c     |  2 +-
 drivers/clocksource/timer-atmel-st.c      |  2 +-
 drivers/clocksource/timer-digicolor.c     |  2 +-
 drivers/clocksource/timer-imx-gpt.c       | 24 ++++++++++++------------
 drivers/clocksource/timer-integrator-ap.c |  2 +-
 drivers/clocksource/timer-keystone.c      |  2 +-
 drivers/clocksource/timer-nps.c           |  4 ++--
 drivers/clocksource/timer-oxnas-rps.c     |  4 ++--
 drivers/clocksource/timer-prima2.c        |  2 +-
 drivers/clocksource/timer-sp804.c         |  4 ++--
 drivers/clocksource/timer-stm32.c         |  2 +-
 drivers/clocksource/timer-sun5i.c         |  4 ++--
 drivers/clocksource/timer-ti-32k.c        |  2 +-
Quoted 8 lines
 drivers/clocksource/timer-u300.c          |  2 +-
 drivers/clocksource/versatile.c           |  4 ++--
 drivers/clocksource/vf_pit_timer.c        |  2 +-
 drivers/clocksource/vt8500_timer.c        |  2 +-
 drivers/clocksource/zevio-timer.c         |  2 +-
 include/asm-generic/vmlinux.lds.h         |  2 --
 include/linux/clocksource.h               |  5 +----
 62 files changed, 98 insertions(+), 117 deletions(-)

For the mps2-timer.c and versatile.c changes:

Thanks for all the work!

Liviu

Quoted 857 lines
arch/arc/kernel/time.c +3 -3
index 36110cd..ee00f2f 100644
@@ -130,7 +130,7 @@ static int __init arc_cs_setup_gfrc(struct device_node *node)
 
 	return clocksource_register_hz(&arc_counter_gfrc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
+CLOCKSOURCE_OF_DECLARE(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
 
 #endif
 
@@ -192,7 +192,7 @@ static int __init arc_cs_setup_rtc(struct device_node *node)
 
 	return clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
+CLOCKSOURCE_OF_DECLARE(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
 
 #endif
 
@@ -379,7 +379,7 @@ static int __init arc_of_timer_init(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(arc_clkevt, "snps,arc-timer", arc_of_timer_init);
+CLOCKSOURCE_OF_DECLARE(arc_clkevt, "snps,arc-timer", arc_of_timer_init);
 
 /*
  * Called from start_kernel() - boot CPU only
arch/arm/kernel/smp_twd.c +3 -3
index 2b24be4..b6ec65e 100644
@@ -412,7 +412,7 @@ out:
 	WARN(err, "twd_local_timer_of_register failed (%d)\n", err);
 	return err;
 }
-CLOCKSOURCE_OF_DECLARE_RET(arm_twd_a9, "arm,cortex-a9-twd-timer", twd_local_timer_of_register);
-CLOCKSOURCE_OF_DECLARE_RET(arm_twd_a5, "arm,cortex-a5-twd-timer", twd_local_timer_of_register);
-CLOCKSOURCE_OF_DECLARE_RET(arm_twd_11mp, "arm,arm11mp-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE(arm_twd_a9, "arm,cortex-a9-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE(arm_twd_a5, "arm,cortex-a5-twd-timer", twd_local_timer_of_register);
+CLOCKSOURCE_OF_DECLARE(arm_twd_11mp, "arm,arm11mp-twd-timer", twd_local_timer_of_register);
 #endif
arch/microblaze/kernel/timer.c +1 -1
index 7f35e7b..5bbf38b 100644
@@ -332,5 +332,5 @@ static int __init xilinx_timer_init(struct device_node *timer)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(xilinx_timer, "xlnx,xps-timer-1.00.a",
+CLOCKSOURCE_OF_DECLARE(xilinx_timer, "xlnx,xps-timer-1.00.a",
 		       xilinx_timer_init);
arch/mips/ralink/cevt-rt3352.c +1 -1
index f2d3c79..f24eee0 100644
@@ -150,4 +150,4 @@ static int __init ralink_systick_init(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(systick, "ralink,cevt-systick", ralink_systick_init);
+CLOCKSOURCE_OF_DECLARE(systick, "ralink,cevt-systick", ralink_systick_init);
arch/nios2/kernel/time.c +1 -1
index 9fa7739..f337eef 100644
@@ -354,4 +354,4 @@ void __init time_init(void)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(nios2_timer, ALTR_TIMER_COMPATIBLE, nios2_time_init);
+CLOCKSOURCE_OF_DECLARE(nios2_timer, ALTR_TIMER_COMPATIBLE, nios2_time_init);
drivers/clocksource/arm_arch_timer.c +3 -3
index d0cda68..9e33309 100644
@@ -784,8 +784,8 @@ static int __init arch_timer_of_init(struct device_node *np)
 
 	return arch_timer_init();
 }
-CLOCKSOURCE_OF_DECLARE_RET(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
-CLOCKSOURCE_OF_DECLARE_RET(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
+CLOCKSOURCE_OF_DECLARE(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
+CLOCKSOURCE_OF_DECLARE(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
 
 static int __init arch_timer_mem_init(struct device_node *np)
 {
@@ -868,7 +868,7 @@ out:
 	of_node_put(best_frame);
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(armv7_arch_timer_mem, "arm,armv7-timer-mem",
+CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
 		       arch_timer_mem_init);
 
 #ifdef CONFIG_ACPI
drivers/clocksource/arm_global_timer.c +1 -1
index 40104fc..2a9ceb6 100644
@@ -358,5 +358,5 @@ out_unmap:
 }
 
 /* Only tested on r2p2 and r3p0  */
-CLOCKSOURCE_OF_DECLARE_RET(arm_gt, "arm,cortex-a9-global-timer",
+CLOCKSOURCE_OF_DECLARE(arm_gt, "arm,cortex-a9-global-timer",
 			global_timer_of_register);
drivers/clocksource/armv7m_systick.c +1 -1
index 2b55410..e93af1f 100644
@@ -81,5 +81,5 @@ out_unmap:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(arm_systick, "arm,armv7m-systick",
+CLOCKSOURCE_OF_DECLARE(arm_systick, "arm,armv7m-systick",
 			system_timer_of_register);
drivers/clocksource/asm9260_timer.c +1 -1
index d113c02..1ba871b 100644
@@ -238,5 +238,5 @@ static int __init asm9260_timer_init(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(asm9260_timer, "alphascale,asm9260-timer",
+CLOCKSOURCE_OF_DECLARE(asm9260_timer, "alphascale,asm9260-timer",
 		asm9260_timer_init);
drivers/clocksource/bcm2835_timer.c +1 -1
index 2dcf896..e71acf2 100644
@@ -142,5 +142,5 @@ static int __init bcm2835_timer_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(bcm2835, "brcm,bcm2835-system-timer",
+CLOCKSOURCE_OF_DECLARE(bcm2835, "brcm,bcm2835-system-timer",
 			bcm2835_timer_init);
drivers/clocksource/bcm_kona_timer.c +2 -2
index 98bc2a2..ee07e7e3 100644
@@ -200,9 +200,9 @@ static int __init kona_timer_init(struct device_node *node)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(brcm_kona, "brcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE(brcm_kona, "brcm,kona-timer", kona_timer_init);
 /*
  * bcm,kona-timer is deprecated by brcm,kona-timer
  * being kept here for driver compatibility
  */
-CLOCKSOURCE_OF_DECLARE_RET(bcm_kona, "bcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);
drivers/clocksource/cadence_ttc_timer.c +1 -1
index e2e7631..388a77b 100644
@@ -539,4 +539,4 @@ static int __init ttc_timer_init(struct device_node *timer)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(ttc, "cdns,ttc", ttc_timer_init);
+CLOCKSOURCE_OF_DECLARE(ttc, "cdns,ttc", ttc_timer_init);
drivers/clocksource/clksrc-dbx500-prcmu.c +1 -1
index 5a59d29..77a365f 100644
@@ -86,5 +86,5 @@ static int __init clksrc_dbx500_prcmu_init(struct device_node *node)
 #endif
 	return clocksource_register_hz(&clocksource_dbx500_prcmu, RATE_32K);
 }
-CLOCKSOURCE_OF_DECLARE_RET(dbx500_prcmu, "stericsson,db8500-prcmu-timer-4",
+CLOCKSOURCE_OF_DECLARE(dbx500_prcmu, "stericsson,db8500-prcmu-timer-4",
 		       clksrc_dbx500_prcmu_init);
drivers/clocksource/clksrc-probe.c +0 -14
index 5fa6a55..bc62be9 100644
@@ -20,19 +20,14 @@
 #include <linux/clocksource.h>
 
 extern struct of_device_id __clksrc_of_table[];
-extern struct of_device_id __clksrc_ret_of_table[];
 
 static const struct of_device_id __clksrc_of_table_sentinel
 	__used __section(__clksrc_of_table_end);
 
-static const struct of_device_id __clksrc_ret_of_table_sentinel
-	__used __section(__clksrc_ret_of_table_end);
-
 void __init clocksource_probe(void)
 {
 	struct device_node *np;
 	const struct of_device_id *match;
-	of_init_fn_1 init_func;
 	of_init_fn_1_ret init_func_ret;
 	unsigned clocksources = 0;
 	int ret;
@@ -41,15 +36,6 @@ void __init clocksource_probe(void)
 		if (!of_device_is_available(np))
 			continue;
 
-		init_func = match->data;
-		init_func(np);
-		clocksources++;
-	}
-
-	for_each_matching_node_and_match(np, __clksrc_ret_of_table, &match) {
-		if (!of_device_is_available(np))
-			continue;
-
 		init_func_ret = match->data;
 
 		ret = init_func_ret(np);
drivers/clocksource/clksrc_st_lpc.c +1 -1
index c9022a9..03cc492 100644
@@ -132,4 +132,4 @@ static int __init st_clksrc_of_register(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(ddata, "st,stih407-lpc", st_clksrc_of_register);
+CLOCKSOURCE_OF_DECLARE(ddata, "st,stih407-lpc", st_clksrc_of_register);
drivers/clocksource/clps711x-timer.c +1 -1
index 3b66198..84aed78 100644
@@ -119,5 +119,5 @@ static int __init clps711x_timer_init(struct device_node *np)
 		return -EINVAL;
 	}
 }
-CLOCKSOURCE_OF_DECLARE_RET(clps711x, "cirrus,clps711x-timer", clps711x_timer_init);
+CLOCKSOURCE_OF_DECLARE(clps711x, "cirrus,clps711x-timer", clps711x_timer_init);
 #endif
drivers/clocksource/dw_apb_timer_of.c +4 -4
index 4985a2c..aee6c0d 100644
@@ -167,7 +167,7 @@ static int __init dw_apb_timer_init(struct device_node *timer)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(pc3x2_timer, "picochip,pc3x2-timer", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(apb_timer_osc, "snps,dw-apb-timer-osc", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(apb_timer_sp, "snps,dw-apb-timer-sp", dw_apb_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(apb_timer, "snps,dw-apb-timer", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE(pc3x2_timer, "picochip,pc3x2-timer", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE(apb_timer_osc, "snps,dw-apb-timer-osc", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE(apb_timer_sp, "snps,dw-apb-timer-sp", dw_apb_timer_init);
+CLOCKSOURCE_OF_DECLARE(apb_timer, "snps,dw-apb-timer", dw_apb_timer_init);
drivers/clocksource/exynos_mct.c +2 -2
index f6caed0..0d18dd4b 100644
@@ -627,5 +627,5 @@ static int __init mct_init_ppi(struct device_node *np)
 {
 	return mct_init_dt(np, MCT_INT_PPI);
 }
-CLOCKSOURCE_OF_DECLARE_RET(exynos4210, "samsung,exynos4210-mct", mct_init_spi);
-CLOCKSOURCE_OF_DECLARE_RET(exynos4412, "samsung,exynos4412-mct", mct_init_ppi);
+CLOCKSOURCE_OF_DECLARE(exynos4210, "samsung,exynos4210-mct", mct_init_spi);
+CLOCKSOURCE_OF_DECLARE(exynos4412, "samsung,exynos4412-mct", mct_init_ppi);
drivers/clocksource/fsl_ftm_timer.c +1 -1
index 9ad4ca3..738515b 100644
@@ -369,4 +369,4 @@ err:
 	kfree(priv);
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(flextimer, "fsl,ftm-timer", ftm_timer_init);
+CLOCKSOURCE_OF_DECLARE(flextimer, "fsl,ftm-timer", ftm_timer_init);
drivers/clocksource/h8300_timer16.c +1 -1
index 9d99fc8..07d9d5b 100644
@@ -187,5 +187,5 @@ free_clk:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(h8300_16bit, "renesas,16bit-timer",
+CLOCKSOURCE_OF_DECLARE(h8300_16bit, "renesas,16bit-timer",
 			   h8300_16timer_init);
drivers/clocksource/h8300_timer8.c +1 -1
index 0292a19..546bb18 100644
@@ -215,4 +215,4 @@ free_clk:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(h8300_8bit, "renesas,8bit-timer", h8300_8timer_init);
+CLOCKSOURCE_OF_DECLARE(h8300_8bit, "renesas,8bit-timer", h8300_8timer_init);
drivers/clocksource/h8300_tpu.c +1 -1
index 4faf718..7bdf199 100644
@@ -154,4 +154,4 @@ free_clk:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(h8300_tpu, "renesas,tpu", h8300_tpu_init);
+CLOCKSOURCE_OF_DECLARE(h8300_tpu, "renesas,tpu", h8300_tpu_init);
drivers/clocksource/meson6_timer.c +1 -1
index 3a6e78f..52af591 100644
@@ -174,5 +174,5 @@ static int __init meson6_timer_init(struct device_node *node)
 					1, 0xfffe);
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(meson6, "amlogic,meson6-timer",
+CLOCKSOURCE_OF_DECLARE(meson6, "amlogic,meson6-timer",
 		       meson6_timer_init);
drivers/clocksource/mips-gic-timer.c +1 -1
index b164b87..1572c7a 100644
@@ -222,5 +222,5 @@ static void __init gic_clocksource_of_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(mips_gic_timer, "mti,gic-timer",
+CLOCKSOURCE_OF_DECLARE(mips_gic_timer, "mti,gic-timer",
 		       gic_clocksource_of_init);
drivers/clocksource/moxart_timer.c +1 -1
index b9c30cd..8414544 100644
@@ -178,4 +178,4 @@ static int __init moxart_timer_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(moxart, "moxa,moxart-timer", moxart_timer_init);
+CLOCKSOURCE_OF_DECLARE(moxart, "moxa,moxart-timer", moxart_timer_init);
drivers/clocksource/mps2-timer.c +1 -1
index c303fa9..3e4431e 100644
@@ -274,4 +274,4 @@ static int __init mps2_timer_init(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(mps2_timer, "arm,mps2-timer", mps2_timer_init);
+CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);
drivers/clocksource/mtk_timer.c +1 -1
index 432a2c0..9065949 100644
@@ -265,4 +265,4 @@ err_kzalloc:
 
 	return -EINVAL;
 }
-CLOCKSOURCE_OF_DECLARE_RET(mtk_mt6577, "mediatek,mt6577-timer", mtk_timer_init);
+CLOCKSOURCE_OF_DECLARE(mtk_mt6577, "mediatek,mt6577-timer", mtk_timer_init);
drivers/clocksource/mxs_timer.c +1 -1
index 17b9d19..630a8d3 100644
@@ -295,4 +295,4 @@ static int __init mxs_timer_init(struct device_node *np)
 
 	return setup_irq(irq, &mxs_timer_irq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(mxs, "fsl,timrot", mxs_timer_init);
+CLOCKSOURCE_OF_DECLARE(mxs, "fsl,timrot", mxs_timer_init);
drivers/clocksource/nomadik-mtu.c +1 -1
index d2be5b3..3c124d1 100644
@@ -284,5 +284,5 @@ static int __init nmdk_timer_of_init(struct device_node *node)
 
 	return nmdk_timer_init(base, irq, pclk, clk);
 }
-CLOCKSOURCE_OF_DECLARE_RET(nomadik_mtu, "st,nomadik-mtu",
+CLOCKSOURCE_OF_DECLARE(nomadik_mtu, "st,nomadik-mtu",
 		       nmdk_timer_of_init);
drivers/clocksource/pxa_timer.c +1 -1
index 59af75c..937e10b 100644
@@ -213,7 +213,7 @@ static int __init pxa_timer_dt_init(struct device_node *np)
 
 	return pxa_timer_common_init(irq, clk_get_rate(clk));
 }
-CLOCKSOURCE_OF_DECLARE_RET(pxa_timer, "marvell,pxa-timer", pxa_timer_dt_init);
+CLOCKSOURCE_OF_DECLARE(pxa_timer, "marvell,pxa-timer", pxa_timer_dt_init);
 
 /*
  * Legacy timer init for non device-tree boards.
drivers/clocksource/qcom-timer.c +2 -2
index 79f73bd..6625763 100644
@@ -273,5 +273,5 @@ static int __init msm_dt_timer_init(struct device_node *np)
 
 	return msm_timer_init(freq, 32, irq, !!percpu_offset);
 }
-CLOCKSOURCE_OF_DECLARE_RET(kpss_timer, "qcom,kpss-timer", msm_dt_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(scss_timer, "qcom,scss-timer", msm_dt_timer_init);
+CLOCKSOURCE_OF_DECLARE(kpss_timer, "qcom,kpss-timer", msm_dt_timer_init);
+CLOCKSOURCE_OF_DECLARE(scss_timer, "qcom,scss-timer", msm_dt_timer_init);
drivers/clocksource/rockchip_timer.c +4 -4
index d10bdee..d10e7a5 100644
@@ -200,7 +200,7 @@ static int __init rk3399_timer_init(struct device_node *np)
 	return rk_timer_init(np, TIMER_CONTROL_REG3399);
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(rk3288_timer, "rockchip,rk3288-timer",
-			   rk3288_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(rk3399_timer, "rockchip,rk3399-timer",
-			   rk3399_timer_init);
+CLOCKSOURCE_OF_DECLARE(rk3288_timer, "rockchip,rk3288-timer",
+		       rk3288_timer_init);
+CLOCKSOURCE_OF_DECLARE(rk3399_timer, "rockchip,rk3399-timer",
+		       rk3399_timer_init);
drivers/clocksource/samsung_pwm_timer.c +4 -4
index 27a9797..54565bd 100644
@@ -466,7 +466,7 @@ static int __init s3c2410_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s3c24xx_variant);
 }
-CLOCKSOURCE_OF_DECLARE_RET(s3c2410_pwm, "samsung,s3c2410-pwm", s3c2410_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(s3c2410_pwm, "samsung,s3c2410-pwm", s3c2410_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s3c64xx_variant = {
 	.bits		= 32,
@@ -479,7 +479,7 @@ static int __init s3c64xx_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s3c64xx_variant);
 }
-CLOCKSOURCE_OF_DECLARE_RET(s3c6400_pwm, "samsung,s3c6400-pwm", s3c64xx_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(s3c6400_pwm, "samsung,s3c6400-pwm", s3c64xx_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s5p64x0_variant = {
 	.bits		= 32,
@@ -492,7 +492,7 @@ static int __init s5p64x0_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s5p64x0_variant);
 }
-CLOCKSOURCE_OF_DECLARE_RET(s5p6440_pwm, "samsung,s5p6440-pwm", s5p64x0_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(s5p6440_pwm, "samsung,s5p6440-pwm", s5p64x0_pwm_clocksource_init);
 
 static const struct samsung_pwm_variant s5p_variant = {
 	.bits		= 32,
@@ -505,5 +505,5 @@ static int __init s5p_pwm_clocksource_init(struct device_node *np)
 {
 	return samsung_pwm_alloc(np, &s5p_variant);
 }
-CLOCKSOURCE_OF_DECLARE_RET(s5pc100_pwm, "samsung,s5pc100-pwm", s5p_pwm_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(s5pc100_pwm, "samsung,s5pc100-pwm", s5p_pwm_clocksource_init);
 #endif
drivers/clocksource/sun4i_timer.c +1 -1
index 4453730..97669ee 100644
@@ -226,5 +226,5 @@ static int __init sun4i_timer_init(struct device_node *node)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(sun4i, "allwinner,sun4i-a10-timer",
+CLOCKSOURCE_OF_DECLARE(sun4i, "allwinner,sun4i-a10-timer",
 		       sun4i_timer_init);
drivers/clocksource/tango_xtal.c +1 -1
index 7dc716c..12fcef8 100644
@@ -53,4 +53,4 @@ static int __init tango_clocksource_init(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(tango, "sigma,tick-counter", tango_clocksource_init);
+CLOCKSOURCE_OF_DECLARE(tango, "sigma,tick-counter", tango_clocksource_init);
drivers/clocksource/tegra20_timer.c +2 -2
index 543c37e..f960891 100644
@@ -237,7 +237,7 @@ static int __init tegra20_init_timer(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(tegra20_timer, "nvidia,tegra20-timer", tegra20_init_timer);
+CLOCKSOURCE_OF_DECLARE(tegra20_timer, "nvidia,tegra20-timer", tegra20_init_timer);
 
 static int __init tegra20_init_rtc(struct device_node *np)
 {
@@ -261,4 +261,4 @@ static int __init tegra20_init_rtc(struct device_node *np)
 
 	return register_persistent_clock(NULL, tegra_read_persistent_clock64);
 }
-CLOCKSOURCE_OF_DECLARE_RET(tegra20_rtc, "nvidia,tegra20-rtc", tegra20_init_rtc);
+CLOCKSOURCE_OF_DECLARE(tegra20_rtc, "nvidia,tegra20-rtc", tegra20_init_rtc);
drivers/clocksource/time-armada-370-xp.c +3 -3
index bc4ab48..a4e5923 100644
@@ -371,7 +371,7 @@ static int __init armada_xp_timer_init(struct device_node *np)
 
 	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE_RET(armada_xp, "marvell,armada-xp-timer",
+CLOCKSOURCE_OF_DECLARE(armada_xp, "marvell,armada-xp-timer",
 		       armada_xp_timer_init);
 
 static int __init armada_375_timer_init(struct device_node *np)
@@ -409,7 +409,7 @@ static int __init armada_375_timer_init(struct device_node *np)
 
 	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE_RET(armada_375, "marvell,armada-375-timer",
+CLOCKSOURCE_OF_DECLARE(armada_375, "marvell,armada-375-timer",
 		       armada_375_timer_init);
 
 static int __init armada_370_timer_init(struct device_node *np)
@@ -432,5 +432,5 @@ static int __init armada_370_timer_init(struct device_node *np)
 
 	return armada_370_xp_timer_common_init(np);
 }
-CLOCKSOURCE_OF_DECLARE_RET(armada_370, "marvell,armada-370-timer",
+CLOCKSOURCE_OF_DECLARE(armada_370, "marvell,armada-370-timer",
 		       armada_370_timer_init);
drivers/clocksource/time-efm32.c +2 -2
index b71ffc6..10a0521 100644
@@ -282,5 +282,5 @@ static int __init efm32_timer_init(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(efm32compat, "efm32,timer", efm32_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(efm32, "energymicro,efm32-timer", efm32_timer_init);
+CLOCKSOURCE_OF_DECLARE(efm32compat, "efm32,timer", efm32_timer_init);
+CLOCKSOURCE_OF_DECLARE(efm32, "energymicro,efm32-timer", efm32_timer_init);
drivers/clocksource/time-lpc32xx.c +1 -1
index cb5b866..9649cfd 100644
@@ -311,4 +311,4 @@ static int __init lpc32xx_timer_init(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(lpc32xx_timer, "nxp,lpc3220-timer", lpc32xx_timer_init);
+CLOCKSOURCE_OF_DECLARE(lpc32xx_timer, "nxp,lpc3220-timer", lpc32xx_timer_init);
drivers/clocksource/time-orion.c +1 -1
index 5fdeb5d..a28f496 100644
@@ -167,4 +167,4 @@ static int __init orion_timer_init(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(orion_timer, "marvell,orion-timer", orion_timer_init);
+CLOCKSOURCE_OF_DECLARE(orion_timer, "marvell,orion-timer", orion_timer_init);
drivers/clocksource/time-pistachio.c +1 -1
index adaaec5..a7d9a08 100644
@@ -214,5 +214,5 @@ static int __init pistachio_clksrc_of_init(struct device_node *node)
 	sched_clock_register(pistachio_read_sched_clock, 32, rate);
 	return clocksource_register_hz(&pcs_gpt.cs, rate);
 }
-CLOCKSOURCE_OF_DECLARE_RET(pistachio_gptimer, "img,pistachio-gptimer",
+CLOCKSOURCE_OF_DECLARE(pistachio_gptimer, "img,pistachio-gptimer",
 		       pistachio_clksrc_of_init);
drivers/clocksource/timer-atlas7.c +1 -1
index 7b1a007..90f8fbc 100644
@@ -304,4 +304,4 @@ static int __init sirfsoc_of_timer_init(struct device_node *np)
 
 	return sirfsoc_atlas7_timer_init(np);
 }
-CLOCKSOURCE_OF_DECLARE_RET(sirfsoc_atlas7_timer, "sirf,atlas7-tick", sirfsoc_of_timer_init);
+CLOCKSOURCE_OF_DECLARE(sirfsoc_atlas7_timer, "sirf,atlas7-tick", sirfsoc_of_timer_init);
drivers/clocksource/timer-atmel-pit.c +1 -1
index ffaca7c..1ffac0c 100644
@@ -270,5 +270,5 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
 
 	return at91sam926x_pit_common_init(data);
 }
-CLOCKSOURCE_OF_DECLARE_RET(at91sam926x_pit, "atmel,at91sam9260-pit",
+CLOCKSOURCE_OF_DECLARE(at91sam926x_pit, "atmel,at91sam9260-pit",
 		       at91sam926x_pit_dt_init);
drivers/clocksource/timer-atmel-st.c +1 -1
index e9331d3..e90ab5b 100644
@@ -260,5 +260,5 @@ static int __init atmel_st_timer_init(struct device_node *node)
 	/* register clocksource */
 	return clocksource_register_hz(&clk32k, sclk_rate);
 }
-CLOCKSOURCE_OF_DECLARE_RET(atmel_st_timer, "atmel,at91rm9200-st",
+CLOCKSOURCE_OF_DECLARE(atmel_st_timer, "atmel,at91rm9200-st",
 		       atmel_st_timer_init);
drivers/clocksource/timer-digicolor.c +1 -1
index b929061..10318cc 100644
@@ -202,5 +202,5 @@ static int __init digicolor_timer_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(conexant_digicolor, "cnxt,cx92755-timer",
+CLOCKSOURCE_OF_DECLARE(conexant_digicolor, "cnxt,cx92755-timer",
 		       digicolor_timer_init);
drivers/clocksource/timer-imx-gpt.c +12 -12
index d5640a74..f595460 100644
@@ -545,15 +545,15 @@ static int __init imx6dl_timer_init_dt(struct device_node *np)
 	return mxc_timer_init_dt(np, GPT_TYPE_IMX6DL);
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(imx1_timer, "fsl,imx1-gpt", imx1_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx21_timer, "fsl,imx21-gpt", imx21_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx27_timer, "fsl,imx27-gpt", imx21_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx31_timer, "fsl,imx31-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx25_timer, "fsl,imx25-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx50_timer, "fsl,imx50-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx51_timer, "fsl,imx51-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx53_timer, "fsl,imx53-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx6q_timer, "fsl,imx6q-gpt", imx31_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx6dl_timer, "fsl,imx6dl-gpt", imx6dl_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx6sl_timer, "fsl,imx6sl-gpt", imx6dl_timer_init_dt);
-CLOCKSOURCE_OF_DECLARE_RET(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx1_timer, "fsl,imx1-gpt", imx1_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx21_timer, "fsl,imx21-gpt", imx21_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx27_timer, "fsl,imx27-gpt", imx21_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx31_timer, "fsl,imx31-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx25_timer, "fsl,imx25-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx50_timer, "fsl,imx50-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx51_timer, "fsl,imx51-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx53_timer, "fsl,imx53-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx6q_timer, "fsl,imx6q-gpt", imx31_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx6dl_timer, "fsl,imx6dl-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx6sl_timer, "fsl,imx6sl-gpt", imx6dl_timer_init_dt);
+CLOCKSOURCE_OF_DECLARE(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
drivers/clocksource/timer-integrator-ap.c +1 -1
index 675face..df6e672 100644
@@ -232,5 +232,5 @@ static int __init integrator_ap_timer_init_of(struct device_node *node)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(integrator_ap_timer, "arm,integrator-timer",
+CLOCKSOURCE_OF_DECLARE(integrator_ap_timer, "arm,integrator-timer",
 		       integrator_ap_timer_init_of);
drivers/clocksource/timer-keystone.c +1 -1
index 4199823..ab68a47 100644
@@ -226,5 +226,5 @@ err:
 	return error;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(keystone_timer, "ti,keystone-timer",
+CLOCKSOURCE_OF_DECLARE(keystone_timer, "ti,keystone-timer",
 			   keystone_timer_init);
drivers/clocksource/timer-nps.c +2 -2
index b5c7b2b..70c149a 100644
@@ -96,5 +96,5 @@ static int __init nps_timer_init(struct device_node *node)
 	return nps_setup_clocksource(node, clk);
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(ezchip_nps400_clksrc, "ezchip,nps400-timer",
-			   nps_timer_init);
+CLOCKSOURCE_OF_DECLARE(ezchip_nps400_clksrc, "ezchip,nps400-timer",
+		       nps_timer_init);
drivers/clocksource/timer-oxnas-rps.c +2 -2
index 0d99f40..bd887e2 100644
@@ -293,5 +293,5 @@ err_alloc:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(ox810se_rps,
-			   "oxsemi,ox810se-rps-timer", oxnas_rps_timer_init);
+CLOCKSOURCE_OF_DECLARE(ox810se_rps,
+		       "oxsemi,ox810se-rps-timer", oxnas_rps_timer_init);
drivers/clocksource/timer-prima2.c +1 -1
index 7b1084d..dae8a66 100644
@@ -246,5 +246,5 @@ static int __init sirfsoc_prima2_timer_init(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(sirfsoc_prima2_timer,
+CLOCKSOURCE_OF_DECLARE(sirfsoc_prima2_timer,
 	"sirf,prima2-tick", sirfsoc_prima2_timer_init);
drivers/clocksource/timer-sp804.c +2 -2
index 7c2944ad..a2b28da 100644
@@ -287,7 +287,7 @@ err:
 	iounmap(base);
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(sp804, "arm,sp804", sp804_of_init);
+CLOCKSOURCE_OF_DECLARE(sp804, "arm,sp804", sp804_of_init);
 
 static int __init integrator_cp_of_init(struct device_node *np)
 {
@@ -336,4 +336,4 @@ err:
 	iounmap(base);
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(intcp, "arm,integrator-cp-timer", integrator_cp_of_init);
+CLOCKSOURCE_OF_DECLARE(intcp, "arm,integrator-cp-timer", integrator_cp_of_init);
drivers/clocksource/timer-stm32.c +1 -1
index d5bf352..1b2574c 100644
@@ -187,4 +187,4 @@ err_clk_get:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(stm32, "st,stm32-timer", stm32_clockevent_init);
+CLOCKSOURCE_OF_DECLARE(stm32, "st,stm32-timer", stm32_clockevent_init);
drivers/clocksource/timer-sun5i.c +2 -2
index f0a3ffb..c184eb8 100644
@@ -346,7 +346,7 @@ static int __init sun5i_timer_init(struct device_node *node)
 
 	return sun5i_setup_clockevent(node, timer_base, clk, irq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(sun5i_a13, "allwinner,sun5i-a13-hstimer",
+CLOCKSOURCE_OF_DECLARE(sun5i_a13, "allwinner,sun5i-a13-hstimer",
 			   sun5i_timer_init);
-CLOCKSOURCE_OF_DECLARE_RET(sun7i_a20, "allwinner,sun7i-a20-hstimer",
+CLOCKSOURCE_OF_DECLARE(sun7i_a20, "allwinner,sun7i-a20-hstimer",
 			   sun5i_timer_init);
drivers/clocksource/timer-ti-32k.c +1 -1
index e4ad3c6e..92b7e39 100644
@@ -124,5 +124,5 @@ static int __init ti_32k_timer_init(struct device_node *np)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(ti_32k_timer, "ti,omap-counter32k",
+CLOCKSOURCE_OF_DECLARE(ti_32k_timer, "ti,omap-counter32k",
 		ti_32k_timer_init);
drivers/clocksource/timer-u300.c +1 -1
index a6a0dec..704e40c 100644
@@ -458,5 +458,5 @@ static int __init u300_timer_init_of(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(u300_timer, "stericsson,u300-apptimer",
+CLOCKSOURCE_OF_DECLARE(u300_timer, "stericsson,u300-apptimer",
 		       u300_timer_init_of);
drivers/clocksource/versatile.c +2 -2
index 8daeffa..220b490 100644
@@ -38,7 +38,7 @@ static int __init versatile_sched_clock_init(struct device_node *node)
 
 	return 0;
 }
-CLOCKSOURCE_OF_DECLARE_RET(vexpress, "arm,vexpress-sysreg",
+CLOCKSOURCE_OF_DECLARE(vexpress, "arm,vexpress-sysreg",
 		       versatile_sched_clock_init);
-CLOCKSOURCE_OF_DECLARE_RET(versatile, "arm,versatile-sysreg",
+CLOCKSOURCE_OF_DECLARE(versatile, "arm,versatile-sysreg",
 		       versatile_sched_clock_init);
drivers/clocksource/vf_pit_timer.c +1 -1
index ca4dff4..55d8d84 100644
@@ -201,4 +201,4 @@ static int __init pit_timer_init(struct device_node *np)
 
 	return pit_clockevent_init(clk_rate, irq);
 }
-CLOCKSOURCE_OF_DECLARE_RET(vf610, "fsl,vf610-pit", pit_timer_init);
+CLOCKSOURCE_OF_DECLARE(vf610, "fsl,vf610-pit", pit_timer_init);
drivers/clocksource/vt8500_timer.c +1 -1
index 1bc8707..b150694 100644
@@ -165,4 +165,4 @@ static int __init vt8500_timer_init(struct device_node *np)
 	return 0;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(vt8500, "via,vt8500-timer", vt8500_timer_init);
+CLOCKSOURCE_OF_DECLARE(vt8500, "via,vt8500-timer", vt8500_timer_init);
drivers/clocksource/zevio-timer.c +1 -1
index cb4cf056..9a53f5e 100644
@@ -215,4 +215,4 @@ static int __init zevio_timer_init(struct device_node *node)
 	return zevio_timer_add(node);
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(zevio_timer, "lsi,zevio-timer", zevio_timer_init);
+CLOCKSOURCE_OF_DECLARE(zevio_timer, "lsi,zevio-timer", zevio_timer_init);
include/asm-generic/vmlinux.lds.h +0 -2
index 8c6c626..6a67ab9 100644
@@ -173,7 +173,6 @@
 	*(__##name##_of_table_end)
 
 #define CLKSRC_OF_TABLES()	OF_TABLE(CONFIG_CLKSRC_OF, clksrc)
-#define CLKSRC_RET_OF_TABLES()	OF_TABLE(CONFIG_CLKSRC_OF, clksrc_ret)
 #define IRQCHIP_OF_MATCH_TABLE() OF_TABLE(CONFIG_IRQCHIP, irqchip)
 #define CLK_OF_TABLES()		OF_TABLE(CONFIG_COMMON_CLK, clk)
 #define IOMMU_OF_TABLES()	OF_TABLE(CONFIG_OF_IOMMU, iommu)
@@ -532,7 +531,6 @@
 	CLK_OF_TABLES()							\
 	RESERVEDMEM_OF_TABLES()						\
 	CLKSRC_OF_TABLES()						\
-	CLKSRC_RET_OF_TABLES()						\
 	IOMMU_OF_TABLES()						\
 	CPU_METHOD_OF_TABLES()						\
 	CPUIDLE_METHOD_OF_TABLES()					\
include/linux/clocksource.h +1 -4
index 15c3839..0839818 100644
@@ -244,10 +244,7 @@ extern int clocksource_mmio_init(void __iomem *, const char *,
 extern int clocksource_i8253_init(void);
 
 #define CLOCKSOURCE_OF_DECLARE(name, compat, fn) \
-	OF_DECLARE_1(clksrc, name, compat, fn)
-
-#define CLOCKSOURCE_OF_DECLARE_RET(name, compat, fn) \
-	OF_DECLARE_1_RET(clksrc_ret, name, compat, fn)
+	OF_DECLARE_1_RET(clksrc, name, compat, fn)
 
 #ifdef CONFIG_CLKSRC_PROBE
 extern void clocksource_probe(void);
Signature · 1 line
1.9.1
Signature · 8 lines
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ?\_(?)_/?
#119 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 74 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 arch/arc/kernel/time.c                    |  6 +++---
 arch/arm/kernel/smp_twd.c                 |  6 +++---
 arch/microblaze/kernel/timer.c            |  2 +-
 arch/mips/ralink/cevt-rt3352.c            |  2 +-
 arch/nios2/kernel/time.c                  |  2 +-
 drivers/clocksource/arm_arch_timer.c      |  6 +++---
 drivers/clocksource/arm_global_timer.c    |  2 +-
 drivers/clocksource/armv7m_systick.c      |  2 +-
 drivers/clocksource/asm9260_timer.c       |  2 +-
 drivers/clocksource/bcm2835_timer.c       |  2 +-
 drivers/clocksource/bcm_kona_timer.c      |  4 ++--
 drivers/clocksource/cadence_ttc_timer.c   |  2 +-
 drivers/clocksource/clksrc-dbx500-prcmu.c |  2 +-
 drivers/clocksource/clksrc-probe.c        | 14 --------------
 drivers/clocksource/clksrc_st_lpc.c       |  2 +-
 drivers/clocksource/clps711x-timer.c      |  2 +-
 drivers/clocksource/dw_apb_timer_of.c     |  8 ++++----
 drivers/clocksource/exynos_mct.c          |  4 ++--
 drivers/clocksource/fsl_ftm_timer.c       |  2 +-
 drivers/clocksource/h8300_timer16.c       |  2 +-
 drivers/clocksource/h8300_timer8.c        |  2 +-
 drivers/clocksource/h8300_tpu.c           |  2 +-
 drivers/clocksource/meson6_timer.c        |  2 +-
 drivers/clocksource/mips-gic-timer.c      |  2 +-
 drivers/clocksource/moxart_timer.c        |  2 +-
 drivers/clocksource/mps2-timer.c          |  2 +-
 drivers/clocksource/mtk_timer.c           |  2 +-
 drivers/clocksource/mxs_timer.c           |  2 +-
 drivers/clocksource/nomadik-mtu.c         |  2 +-
 drivers/clocksource/pxa_timer.c           |  2 +-
 drivers/clocksource/qcom-timer.c          |  4 ++--
 drivers/clocksource/rockchip_timer.c      |  8 ++++----
 drivers/clocksource/samsung_pwm_timer.c   |  8 ++++----
 drivers/clocksource/sun4i_timer.c         |  2 +-
 drivers/clocksource/tango_xtal.c          |  2 +-
 drivers/clocksource/tegra20_timer.c       |  4 ++--
 drivers/clocksource/time-armada-370-xp.c  |  6 +++---
 drivers/clocksource/time-efm32.c          |  4 ++--
 drivers/clocksource/time-lpc32xx.c        |  2 +-
 drivers/clocksource/time-orion.c          |  2 +-
 drivers/clocksource/time-pistachio.c      |  2 +-
 drivers/clocksource/timer-atlas7.c        |  2 +-
 drivers/clocksource/timer-atmel-pit.c     |  2 +-
 drivers/clocksource/timer-atmel-st.c      |  2 +-
 drivers/clocksource/timer-digicolor.c     |  2 +-
 drivers/clocksource/timer-imx-gpt.c       | 24 ++++++++++++------------
 drivers/clocksource/timer-integrator-ap.c |  2 +-
 drivers/clocksource/timer-keystone.c      |  2 +-
 drivers/clocksource/timer-nps.c           |  4 ++--
 drivers/clocksource/timer-oxnas-rps.c     |  4 ++--
 drivers/clocksource/timer-prima2.c        |  2 +-
 drivers/clocksource/timer-sp804.c         |  4 ++--
 drivers/clocksource/timer-stm32.c         |  2 +-
 drivers/clocksource/timer-sun5i.c         |  4 ++--
 drivers/clocksource/timer-ti-32k.c        |  2 +-
 drivers/clocksource/timer-u300.c          |  2 +-
 drivers/clocksource/versatile.c           |  4 ++--
 drivers/clocksource/vf_pit_timer.c        |  2 +-
 drivers/clocksource/vt8500_timer.c        |  2 +-
 drivers/clocksource/zevio-timer.c         |  2 +-
 include/asm-generic/vmlinux.lds.h         |  2 --
 include/linux/clocksource.h               |  5 +----
 62 files changed, 98 insertions(+), 117 deletions(-)

[...]

drivers/clocksource/timer-oxnas-rps.c err_alloc: · line 297

Quoted 12 lines
drivers/clocksource/timer-oxnas-rps.c +2 -2
index 0d99f40..bd887e2 100644
@@ -293,5 +293,5 @@ err_alloc:
 	return ret;
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(ox810se_rps,
-			   "oxsemi,ox810se-rps-timer", oxnas_rps_timer_init);
+CLOCKSOURCE_OF_DECLARE(ox810se_rps,
+		       "oxsemi,ox810se-rps-timer", oxnas_rps_timer_init);

For the OXNAS part :

Thanks,
Neil

#120 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 74 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 arch/arc/kernel/time.c                    |  6 +++---
 arch/arm/kernel/smp_twd.c                 |  6 +++---
 arch/microblaze/kernel/timer.c            |  2 +-
 arch/mips/ralink/cevt-rt3352.c            |  2 +-
 arch/nios2/kernel/time.c                  |  2 +-
 drivers/clocksource/arm_arch_timer.c      |  6 +++---
 drivers/clocksource/arm_global_timer.c    |  2 +-
 drivers/clocksource/armv7m_systick.c      |  2 +-
 drivers/clocksource/asm9260_timer.c       |  2 +-
 drivers/clocksource/bcm2835_timer.c       |  2 +-
 drivers/clocksource/bcm_kona_timer.c      |  4 ++--
 drivers/clocksource/cadence_ttc_timer.c   |  2 +-
 drivers/clocksource/clksrc-dbx500-prcmu.c |  2 +-
 drivers/clocksource/clksrc-probe.c        | 14 --------------
 drivers/clocksource/clksrc_st_lpc.c       |  2 +-
 drivers/clocksource/clps711x-timer.c      |  2 +-
 drivers/clocksource/dw_apb_timer_of.c     |  8 ++++----
 drivers/clocksource/exynos_mct.c          |  4 ++--
 drivers/clocksource/fsl_ftm_timer.c       |  2 +-
 drivers/clocksource/h8300_timer16.c       |  2 +-
 drivers/clocksource/h8300_timer8.c        |  2 +-
 drivers/clocksource/h8300_tpu.c           |  2 +-
 drivers/clocksource/meson6_timer.c        |  2 +-
 drivers/clocksource/mips-gic-timer.c      |  2 +-
 drivers/clocksource/moxart_timer.c        |  2 +-
 drivers/clocksource/mps2-timer.c          |  2 +-
 drivers/clocksource/mtk_timer.c           |  2 +-
 drivers/clocksource/mxs_timer.c           |  2 +-
 drivers/clocksource/nomadik-mtu.c         |  2 +-
 drivers/clocksource/pxa_timer.c           |  2 +-
 drivers/clocksource/qcom-timer.c          |  4 ++--
 drivers/clocksource/rockchip_timer.c      |  8 ++++----
 drivers/clocksource/samsung_pwm_timer.c   |  8 ++++----
 drivers/clocksource/sun4i_timer.c         |  2 +-
 drivers/clocksource/tango_xtal.c          |  2 +-
 drivers/clocksource/tegra20_timer.c       |  4 ++--
 drivers/clocksource/time-armada-370-xp.c  |  6 +++---
 drivers/clocksource/time-efm32.c          |  4 ++--
 drivers/clocksource/time-lpc32xx.c        |  2 +-
 drivers/clocksource/time-orion.c          |  2 +-
 drivers/clocksource/time-pistachio.c      |  2 +-
 drivers/clocksource/timer-atlas7.c        |  2 +-
 drivers/clocksource/timer-atmel-pit.c     |  2 +-
 drivers/clocksource/timer-atmel-st.c      |  2 +-
 drivers/clocksource/timer-digicolor.c     |  2 +-
 drivers/clocksource/timer-imx-gpt.c       | 24 ++++++++++++------------
 drivers/clocksource/timer-integrator-ap.c |  2 +-
 drivers/clocksource/timer-keystone.c      |  2 +-
 drivers/clocksource/timer-nps.c           |  4 ++--
 drivers/clocksource/timer-oxnas-rps.c     |  4 ++--
 drivers/clocksource/timer-prima2.c        |  2 +-
 drivers/clocksource/timer-sp804.c         |  4 ++--
 drivers/clocksource/timer-stm32.c         |  2 +-
 drivers/clocksource/timer-sun5i.c         |  4 ++--
 drivers/clocksource/timer-ti-32k.c        |  2 +-
 drivers/clocksource/timer-u300.c          |  2 +-
 drivers/clocksource/versatile.c           |  4 ++--
 drivers/clocksource/vf_pit_timer.c        |  2 +-
 drivers/clocksource/vt8500_timer.c        |  2 +-
 drivers/clocksource/zevio-timer.c         |  2 +-
 include/asm-generic/vmlinux.lds.h         |  2 --
 include/linux/clocksource.h               |  5 +----
 62 files changed, 98 insertions(+), 117 deletions(-)

[..]

drivers/clocksource/time-lpc32xx.c static int __init lpc32xx_timer_init(struct device_node *np) · line 314

Quoted 10 lines
drivers/clocksource/time-lpc32xx.c +1 -1
index cb5b866..9649cfd 100644
@@ -311,4 +311,4 @@ static int __init lpc32xx_timer_init(struct device_node *np)
 
 	return ret;
 }
-CLOCKSOURCE_OF_DECLARE_RET(lpc32xx_timer, "nxp,lpc3220-timer", lpc32xx_timer_init);
+CLOCKSOURCE_OF_DECLARE(lpc32xx_timer, "nxp,lpc3220-timer", lpc32xx_timer_init);

For LPC32xx driver:

#121 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano

Hi Daniel,

Quoted 73 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 arch/arc/kernel/time.c                    |  6 +++---
 arch/arm/kernel/smp_twd.c                 |  6 +++---
 arch/microblaze/kernel/timer.c            |  2 +-
 arch/mips/ralink/cevt-rt3352.c            |  2 +-
 arch/nios2/kernel/time.c                  |  2 +-
 drivers/clocksource/arm_arch_timer.c      |  6 +++---
 drivers/clocksource/arm_global_timer.c    |  2 +-
 drivers/clocksource/armv7m_systick.c      |  2 +-
 drivers/clocksource/asm9260_timer.c       |  2 +-
 drivers/clocksource/bcm2835_timer.c       |  2 +-
 drivers/clocksource/bcm_kona_timer.c      |  4 ++--
 drivers/clocksource/cadence_ttc_timer.c   |  2 +-
 drivers/clocksource/clksrc-dbx500-prcmu.c |  2 +-
 drivers/clocksource/clksrc-probe.c        | 14 --------------
 drivers/clocksource/clksrc_st_lpc.c       |  2 +-
 drivers/clocksource/clps711x-timer.c      |  2 +-
 drivers/clocksource/dw_apb_timer_of.c     |  8 ++++----
 drivers/clocksource/exynos_mct.c          |  4 ++--
 drivers/clocksource/fsl_ftm_timer.c       |  2 +-
 drivers/clocksource/h8300_timer16.c       |  2 +-
 drivers/clocksource/h8300_timer8.c        |  2 +-
 drivers/clocksource/h8300_tpu.c           |  2 +-
 drivers/clocksource/meson6_timer.c        |  2 +-
 drivers/clocksource/mips-gic-timer.c      |  2 +-
 drivers/clocksource/moxart_timer.c        |  2 +-
 drivers/clocksource/mps2-timer.c          |  2 +-
 drivers/clocksource/mtk_timer.c           |  2 +-
 drivers/clocksource/mxs_timer.c           |  2 +-
 drivers/clocksource/nomadik-mtu.c         |  2 +-
 drivers/clocksource/pxa_timer.c           |  2 +-
 drivers/clocksource/qcom-timer.c          |  4 ++--
 drivers/clocksource/rockchip_timer.c      |  8 ++++----
 drivers/clocksource/samsung_pwm_timer.c   |  8 ++++----
 drivers/clocksource/sun4i_timer.c         |  2 +-
 drivers/clocksource/tango_xtal.c          |  2 +-
 drivers/clocksource/tegra20_timer.c       |  4 ++--
 drivers/clocksource/time-armada-370-xp.c  |  6 +++---
 drivers/clocksource/time-efm32.c          |  4 ++--
 drivers/clocksource/time-lpc32xx.c        |  2 +-
 drivers/clocksource/time-orion.c          |  2 +-
 drivers/clocksource/time-pistachio.c      |  2 +-
 drivers/clocksource/timer-atlas7.c        |  2 +-
 drivers/clocksource/timer-atmel-pit.c     |  2 +-
 drivers/clocksource/timer-atmel-st.c      |  2 +-
 drivers/clocksource/timer-digicolor.c     |  2 +-
 drivers/clocksource/timer-imx-gpt.c       | 24 ++++++++++++------------
 drivers/clocksource/timer-integrator-ap.c |  2 +-
 drivers/clocksource/timer-keystone.c      |  2 +-
 drivers/clocksource/timer-nps.c           |  4 ++--
 drivers/clocksource/timer-oxnas-rps.c     |  4 ++--
 drivers/clocksource/timer-prima2.c        |  2 +-
 drivers/clocksource/timer-sp804.c         |  4 ++--
 drivers/clocksource/timer-stm32.c         |  2 +-
 drivers/clocksource/timer-sun5i.c         |  4 ++--
 drivers/clocksource/timer-ti-32k.c        |  2 +-
 drivers/clocksource/timer-u300.c          |  2 +-
 drivers/clocksource/versatile.c           |  4 ++--
 drivers/clocksource/vf_pit_timer.c        |  2 +-
 drivers/clocksource/vt8500_timer.c        |  2 +-
 drivers/clocksource/zevio-timer.c         |  2 +-
 include/asm-generic/vmlinux.lds.h         |  2 --
 include/linux/clocksource.h               |  5 +----
 62 files changed, 98 insertions(+), 117 deletions(-)

[..]

Quoted 6 lines
drivers/clocksource/bcm_kona_timer.c +0 -0
index 98bc2a2..ee07e7e3 100644
@@ -200,9 +200,9 @@ static int __init kona_timer_init(struct device_node *node)
 	return 0;

drivers/clocksource/bcm_kona_timer.c static int __init kona_timer_init(struct device_node *node) · line 208

Quoted 10 lines
drivers/clocksource/bcm_kona_timer.c +2 -2
 }
 
-CLOCKSOURCE_OF_DECLARE_RET(brcm_kona, "brcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE(brcm_kona, "brcm,kona-timer", kona_timer_init);
 /*
  * bcm,kona-timer is deprecated by brcm,kona-timer
  * being kept here for driver compatibility
  */
-CLOCKSOURCE_OF_DECLARE_RET(bcm_kona, "bcm,kona-timer", kona_timer_init);
+CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);

For Broadcom Kona timer change:

Thanks!

Ray

#122 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 74 lines

From: Daniel Lezcano [mailto:daniel.lezcano at linaro.org]
Sent: Friday, June 17, 2016 12:27 AM

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---

arch/arc/kernel/time.c                    |  6 +++---
arch/arm/kernel/smp_twd.c                 |  6 +++---
arch/microblaze/kernel/timer.c            |  2 +-
arch/mips/ralink/cevt-rt3352.c            |  2 +-
arch/nios2/kernel/time.c                  |  2 +-
drivers/clocksource/arm_arch_timer.c      |  6 +++---
drivers/clocksource/arm_global_timer.c    |  2 +-
drivers/clocksource/armv7m_systick.c      |  2 +-
drivers/clocksource/asm9260_timer.c       |  2 +-
drivers/clocksource/bcm2835_timer.c       |  2 +-
drivers/clocksource/bcm_kona_timer.c      |  4 ++--
drivers/clocksource/cadence_ttc_timer.c   |  2 +-
drivers/clocksource/clksrc-dbx500-prcmu.c |  2 +-
drivers/clocksource/clksrc-probe.c        | 14 --------------
drivers/clocksource/clksrc_st_lpc.c       |  2 +-
drivers/clocksource/clps711x-timer.c      |  2 +-
drivers/clocksource/dw_apb_timer_of.c     |  8 ++++----
drivers/clocksource/exynos_mct.c          |  4 ++--
drivers/clocksource/fsl_ftm_timer.c       |  2 +-
drivers/clocksource/h8300_timer16.c       |  2 +-
drivers/clocksource/h8300_timer8.c        |  2 +-
drivers/clocksource/h8300_tpu.c           |  2 +-
drivers/clocksource/meson6_timer.c        |  2 +-
drivers/clocksource/mips-gic-timer.c      |  2 +-
drivers/clocksource/moxart_timer.c        |  2 +-
drivers/clocksource/mps2-timer.c          |  2 +-
drivers/clocksource/mtk_timer.c           |  2 +-
drivers/clocksource/mxs_timer.c           |  2 +-
drivers/clocksource/nomadik-mtu.c         |  2 +-
drivers/clocksource/pxa_timer.c           |  2 +-
drivers/clocksource/qcom-timer.c          |  4 ++--
drivers/clocksource/rockchip_timer.c      |  8 ++++----
drivers/clocksource/samsung_pwm_timer.c   |  8 ++++----
drivers/clocksource/sun4i_timer.c         |  2 +-
drivers/clocksource/tango_xtal.c          |  2 +-
drivers/clocksource/tegra20_timer.c       |  4 ++--
drivers/clocksource/time-armada-370-xp.c  |  6 +++---
drivers/clocksource/time-efm32.c          |  4 ++--
drivers/clocksource/time-lpc32xx.c        |  2 +-
drivers/clocksource/time-orion.c          |  2 +-
drivers/clocksource/time-pistachio.c      |  2 +-
drivers/clocksource/timer-atlas7.c        |  2 +-
drivers/clocksource/timer-atmel-pit.c     |  2 +-
drivers/clocksource/timer-atmel-st.c      |  2 +-
drivers/clocksource/timer-digicolor.c     |  2 +-
drivers/clocksource/timer-imx-gpt.c       | 24 ++++++++++++------------
drivers/clocksource/timer-integrator-ap.c |  2 +-
drivers/clocksource/timer-keystone.c      |  2 +-
drivers/clocksource/timer-nps.c           |  4 ++--
drivers/clocksource/timer-oxnas-rps.c     |  4 ++--
drivers/clocksource/timer-prima2.c        |  2 +-
drivers/clocksource/timer-sp804.c         |  4 ++--
drivers/clocksource/timer-stm32.c         |  2 +-
drivers/clocksource/timer-sun5i.c         |  4 ++--
drivers/clocksource/timer-ti-32k.c        |  2 +-
drivers/clocksource/timer-u300.c          |  2 +-
drivers/clocksource/versatile.c           |  4 ++--
drivers/clocksource/vf_pit_timer.c        |  2 +-
drivers/clocksource/vt8500_timer.c        |  2 +-
drivers/clocksource/zevio-timer.c         |  2 +-
include/asm-generic/vmlinux.lds.h         |  2 --
include/linux/clocksource.h               |  5 +----
62 files changed, 98 insertions(+), 117 deletions(-)

[..]

Quoted 15 lines
drivers/clocksource/timer-nps.c +2 -2
@@ -96,5 +96,5 @@ static int __init nps_timer_init(struct device_node *node)
 	return nps_setup_clocksource(node, clk);  }
 
-CLOCKSOURCE_OF_DECLARE_RET(ezchip_nps400_clksrc, "ezchip,nps400-timer",
-			   nps_timer_init);
+CLOCKSOURCE_OF_DECLARE(ezchip_nps400_clksrc, "ezchip,nps400-timer",
+		       nps_timer_init);
drivers/clocksource/timer-oxnas-rps.c +0 -0
index 0d99f40..bd887e2 100644

drivers/clocksource/timer-oxnas-rps.c err_alloc: · line 294

Quoted 2 lines
drivers/clocksource/timer-oxnas-rps.c +0 -0
@@ -293,5 +293,5 @@ err_alloc:
 	return ret;
 }
#123 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 4 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Quoted 8 lines

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 drivers/clocksource/sun4i_timer.c         |  2 +-
 drivers/clocksource/timer-sun5i.c         |  4 ++--
#124 lore raw

PATCH v2 63/63 clocksources: Switch back to the clksrc table

In reply to Daniel Lezcano
Quoted 11 lines · Daniel Lezcano

All the clocksource drivers's init function are now converted to return an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the clksrc-of table.

Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of

---
 drivers/clocksource/meson6_timer.c        |  2 +-