arm: imx: Add support for Advantech DMS-BA16 board

Add support for Advantech DMS-BA16 board. The board is based on Advantech BA16 module which has a i.MX6D processor. The board supports:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display

Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash Supports OpenGL ES 2.0 and OpenVG 1.1 HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port, 1x micro SD (SDHC),1x SDIO, 1x SATA II, 1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2

Signed-off-by Akshay Bhat <[email protected]>

Cc u-boot at lists.denx.de

Cc sbabic at denx.de

---

v1 -> v2:
Address comments made by Stefano Babic:
- Remove redundant clock enable code in .cfg
- Use register names instead of hardcoded address in .cfg
- Factorize .cfg into several files to make it modular for re-use
- Use imx_ddr_size instead of get_ram_size
- Fix multiline comments
- Move USB gadget related CONFIG_ from header file to defconfig

 arch/arm/cpu/armv7/mx6/Kconfig           |   5 +
 board/advantech/dms-ba16/Kconfig         |  27 ++
 board/advantech/dms-ba16/MAINTAINERS     |   8 +
 board/advantech/dms-ba16/Makefile        |   8 +
 board/advantech/dms-ba16/clocks.cfg      |  25 ++
 board/advantech/dms-ba16/ddr-setup.cfg   |  39 +++
 board/advantech/dms-ba16/dms-ba16.c      | 570 +++++++++++++++++++++++++++++++
 board/advantech/dms-ba16/dms-ba16_1g.cfg |  25 ++
 board/advantech/dms-ba16/dms-ba16_2g.cfg |  25 ++
 board/advantech/dms-ba16/micron-1g.cfg   |  63 ++++
 board/advantech/dms-ba16/samsung-2g.cfg  |  63 ++++
 configs/dms-ba16-1g_defconfig            |  34 ++
 configs/dms-ba16_defconfig               |  33 ++
 include/configs/advantech_dms-ba16.h     | 315 +++++++++++++++++
 14 files changed, 1240 insertions(+)
 create mode 100644 board/advantech/dms-ba16/Kconfig
 create mode 100644 board/advantech/dms-ba16/MAINTAINERS
 create mode 100644 board/advantech/dms-ba16/Makefile
 create mode 100644 board/advantech/dms-ba16/clocks.cfg
 create mode 100644 board/advantech/dms-ba16/ddr-setup.cfg
 create mode 100644 board/advantech/dms-ba16/dms-ba16.c
 create mode 100644 board/advantech/dms-ba16/dms-ba16_1g.cfg
 create mode 100644 board/advantech/dms-ba16/dms-ba16_2g.cfg
 create mode 100644 board/advantech/dms-ba16/micron-1g.cfg
 create mode 100644 board/advantech/dms-ba16/samsung-2g.cfg
 create mode 100644 configs/dms-ba16-1g_defconfig
 create mode 100644 configs/dms-ba16_defconfig
 create mode 100644 include/configs/advantech_dms-ba16.h

arch/arm/cpu/armv7/mx6/Kconfig +5 -0

index 663f970..1e4a1cb 100644
@@ -35,6 +35,10 @@ choice
 	prompt "MX6 board select"
 	optional
 
+config TARGET_ADVANTECH_DMS_BA16
+	bool "Advantech dms-ba16"
+	select MX6Q
+
 config TARGET_ARISTAINETOS
 	bool "aristainetos"
 

@@ -184,6 +188,7 @@ config SYS_SOC
 	default "mx6"
 
 source "board/ge/bx50v3/Kconfig"
+source "board/advantech/dms-ba16/Kconfig"
 source "board/aristainetos/Kconfig"
 source "board/bachmann/ot1200/Kconfig"
 source "board/barco/platinum/Kconfig"

board/advantech/dms-ba16/Kconfig new file +27 -0

new file mode 100644
index 0000000..cc5b4e3
@@ -0,0 +1,27 @@
+choice
+	prompt "DDR Size"
+	default SYS_DDR_2G
+
+config SYS_DDR_1G
+	bool "1GiB"
+
+config SYS_DDR_2G
+	bool "2GiB"
+
+endchoice
+
+config IMX_CONFIG
+	default "board/advantech/dms-ba16/dms-ba16_2g.cfg" if SYS_DDR_2G
+	default "board/advantech/dms-ba16/dms-ba16_1g.cfg" if SYS_DDR_1G
+
+config SYS_BOARD
+	default "dms-ba16"
+
+config SYS_VENDOR
+	default "advantech"
+
+config SYS_SOC
+	default "mx6"
+
+config SYS_CONFIG_NAME
+	default "advantech_dms-ba16"

board/advantech/dms-ba16/MAINTAINERS new file +8 -0

new file mode 100644
index 0000000..e8ea3dd
@@ -0,0 +1,8 @@
+ADVANTECH_DMS-BA16 BOARD
+M:	Akshay Bhat <[email protected]>
+M:	Ken Lin <[email protected]>
+S:	Maintained
+F:	board/advantech/dms-ba16/
+F:	include/configs/advantech_dms-ba16.h
+F:	configs/dms-ba16_defconfig
+F:	configs/dms-ba16-1g_defconfig

board/advantech/dms-ba16/Makefile new file +8 -0

new file mode 100644
index 0000000..ec9aaa8
@@ -0,0 +1,8 @@
+#
+# Copyright 2016 Timesys Corporation
+# Copyright 2016 Advantech Corporation
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := dms-ba16.o

board/advantech/dms-ba16/clocks.cfg new file +25 -0

new file mode 100644
index 0000000..abc769c
@@ -0,0 +1,25 @@
+/* set the default clock gate to save power */
+DATA 4, CCM_CCGR0, 0x00C03F3F
+DATA 4, CCM_CCGR1, 0x0030FC03
+DATA 4, CCM_CCGR2, 0x0FFFC000
+DATA 4, CCM_CCGR3, 0x3FF00000
+DATA 4, CCM_CCGR4, 0x00FFF300
+DATA 4, CCM_CCGR5, 0x0F0000C3
+DATA 4, CCM_CCGR6, 0x000003FF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
+DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
+
+/*
+ * Setup CCM_CCOSR register as follows:
+ *
+ * cko1_en  1    --> CKO1 enabled
+ * cko1_div 111  --> divide by 8
+ * cko1_sel 1011 --> ahb_clk_root
+ *
+ * This sets CKO1 at ahb_clk_root/8 132/8 16.5 MHz
+ */
+DATA 4, CCM_CCOSR, 0x000000fb

board/advantech/dms-ba16/ddr-setup.cfg new file +39 -0

new file mode 100644
index 0000000..4c43e64
@@ -0,0 +1,39 @@
+/* DDR IO */
+DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000c0000
+DATA 4, MX6_IOM_GRP_DDRPKE,   0x00000000
+DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000030
+DATA 4, MX6_IOM_DRAM_CAS,     0x00000030
+DATA 4, MX6_IOM_DRAM_RAS,     0x00000030
+DATA 4, MX6_IOM_GRP_ADDDS,    0x00000030
+DATA 4, MX6_IOM_DRAM_RESET,   0x00000030
+DATA 4, MX6_IOM_DRAM_SDBA2,   0x00000000
+DATA 4, MX6_IOM_DRAM_SDODT0,  0x00000030
+DATA 4, MX6_IOM_DRAM_SDODT1,  0x00000030
+DATA 4, MX6_IOM_GRP_CTLDS,    0x00000030
+DATA 4, MX6_IOM_DDRMODE_CTL,  0x00020000
+DATA 4, MX6_IOM_DRAM_SDQS0,   0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS1,   0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS2,   0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS3,   0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS4,   0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS5,   0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS6,   0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS7,   0x00000030
+DATA 4, MX6_IOM_GRP_DDRMODE,  0x00020000
+DATA 4, MX6_IOM_GRP_B0DS,     0x00000030
+DATA 4, MX6_IOM_GRP_B1DS,     0x00000030
+DATA 4, MX6_IOM_GRP_B2DS,     0x00000030
+DATA 4, MX6_IOM_GRP_B3DS,     0x00000030
+DATA 4, MX6_IOM_GRP_B4DS,     0x00000030
+DATA 4, MX6_IOM_GRP_B5DS,     0x00000030
+DATA 4, MX6_IOM_GRP_B6DS,     0x00000030
+DATA 4, MX6_IOM_GRP_B7DS,     0x00000030
+DATA 4, MX6_IOM_DRAM_DQM0,    0x00000030
+DATA 4, MX6_IOM_DRAM_DQM1,    0x00000030
+DATA 4, MX6_IOM_DRAM_DQM2,    0x00000030
+DATA 4, MX6_IOM_DRAM_DQM3,    0x00000030
+DATA 4, MX6_IOM_DRAM_DQM4,    0x00000030
+DATA 4, MX6_IOM_DRAM_DQM5,    0x00000030
+DATA 4, MX6_IOM_DRAM_DQM6,    0x00000030
+DATA 4, MX6_IOM_DRAM_DQM7,    0x00000030

board/advantech/dms-ba16/dms-ba16.c new file +570 -0

new file mode 100644
index 0000000..f0f1976
@@ -0,0 +1,570 @@
+/*
+ * Copyright 2016 Timesys Corporation
+ * Copyright 2016 Advantech Corporation
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <pwm.h>
+DECLARE_GLOBAL_DATA_PTR;
+
+#define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP |	\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |	\
+	PAD_CTL_HYS)
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |	\
+	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
+	PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart3_pads[] = {
+	MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC   | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK  | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	/* AR8033 PHY Reset */
+	MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+	/* Reset AR8033 PHY */
+	gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
+	udelay(500);
+	gpio_set_value(IMX_GPIO_NR(1, 28), 1);
+}
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_GPIO_4__GPIO1_IO04	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
+		.gp = IMX_GPIO_NR(5, 26)
+	}
+};
+
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 12)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 13)
+	}
+};
+
+static struct i2c_pads_info i2c_pad_info3 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 3)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 6)
+	}
+};
+
+#ifdef CONFIG_MXC_SPI
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
+}
+
+static void setup_spi(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+}
+#endif
+
+static iomux_v3_cfg_t const pcie_pads[] = {
+	MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_pcie(void)
+{
+	imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
+}
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC2_BASE_ADDR},
+	{USDHC3_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+#define USDHC4_CD_GPIO	IMX_GPIO_NR(6, 11)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = 1; /* eMMC is always present */
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = !gpio_get_value(USDHC4_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+	int i;
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_direction_input(USDHC2_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		case 2:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			gpio_direction_input(USDHC4_CD_GPIO);
+			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers\n"
+			       "(%d) then supported by the board (%d)\n",
+			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+#endif
+
+static int mx6_rgmii_rework(struct phy_device *phydev)
+{
+	/* set device address 0x7 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+	/* offset 0x8016: CLK_25M Clock Select */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+	/* enable register write, no post increment, address 0x7 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+	/* set to 125 MHz from local PLL source */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
+	/* set debug port address: SerDes Test and System Mode Control */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	/* enable rgmii tx clock delay */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	mx6_rgmii_rework(phydev);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+#if defined(CONFIG_VIDEO_IPUV3)
+static iomux_v3_cfg_t const backlight_pads[] = {
+	/* Power for LVDS Display */
+	MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
+#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
+	/* Backlight enable for LVDS display */
+	MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
+#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
+	/* backlight PWM brightness control */
+	MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+int board_cfb_skip(void)
+{
+	gpio_direction_output(LVDS_POWER_GP, 1);
+
+	return 0;
+}
+
+static int detect_baseboard(struct display_info_t const *dev)
+{
+	return 0 == dev->addr;
+}
+
+struct display_info_t const displays[] = {{
+	.bus	= -1,
+	.addr	= 0,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_baseboard,
+	.enable	= NULL,
+	.mode	= {
+		.name           = "SHARP-LQ156M1LG21",
+		.refresh        = 60,
+		.xres           = 1920,
+		.yres           = 1080,
+		.pixclock       = 7851,
+		.left_margin    = 100,
+		.right_margin   = 40,
+		.upper_margin   = 30,
+		.lower_margin   = 3,
+		.hsync_len      = 10,
+		.vsync_len      = 2,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} }, {
+	.bus	= -1,
+	.addr	= 3,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_hdmi,
+	.enable	= do_enable_hdmi,
+	.mode	= {
+		.name           = "HDMI",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
+
+	imx_setup_hdmi();
+
+	/* Set LDB_DI0 as clock source for IPU_DI0 */
+	clrsetbits_le32(&mxc_ccm->chsccdr,
+			MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
+			(CHSCCDR_CLK_SEL_LDB_DI0 <<
+			 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
+
+	/* Turn on IPU LDB DI0 clocks */
+	setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
+
+	enable_ipu_clock();
+
+	writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
+	       IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH |
+	       IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
+	       IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
+	       IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT |
+	       IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
+	       IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
+	       IOMUXC_GPR2_SPLIT_MODE_EN_MASK |
+	       IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 |
+	       IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0,
+	       &iomux->gpr[2]);
+
+	clrsetbits_le32(&iomux->gpr[3],
+			IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
+			IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
+			IOMUXC_GPR3_HDMI_MUX_CTL_MASK,
+		       (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
+			IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
+
+	/* backlights off until needed */
+	imx_iomux_v3_setup_multiple_pads(backlight_pads,
+					 ARRAY_SIZE(backlight_pads));
+
+	gpio_direction_input(LVDS_POWER_GP);
+	gpio_direction_input(LVDS_BACKLIGHT_GP);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+	setup_pcie();
+
+	return cpu_eth_init(bis);
+}
+
+static iomux_v3_cfg_t const misc_pads[] = {
+	MX6_PAD_KEY_ROW2__GPIO4_IO11	| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_A25__GPIO5_IO02	| MUX_PAD_CTRL(NC_PAD_CTRL),
+	MX6_PAD_EIM_CS0__GPIO2_IO23	| MUX_PAD_CTRL(NC_PAD_CTRL),
+	MX6_PAD_EIM_CS1__GPIO2_IO24	| MUX_PAD_CTRL(NC_PAD_CTRL),
+	MX6_PAD_EIM_OE__GPIO2_IO25	| MUX_PAD_CTRL(NC_PAD_CTRL),
+	MX6_PAD_EIM_BCLK__GPIO6_IO31	| MUX_PAD_CTRL(NC_PAD_CTRL),
+	MX6_PAD_GPIO_1__GPIO1_IO01	| MUX_PAD_CTRL(NC_PAD_CTRL),
+};
+#define SUS_S3_OUT	IMX_GPIO_NR(4, 11)
+#define WIFI_EN	IMX_GPIO_NR(6, 14)
+
+int setup_ba16_sata(void)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	ret = enable_sata_clock();
+	if (ret)
+		return ret;
+
+	clrsetbits_le32(&iomuxc_regs->gpr[13],
+			IOMUXC_GPR13_SATA_MASK,
+			IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB
+			|IOMUXC_GPR13_SATA_PHY_7_SATA2M
+			|IOMUXC_GPR13_SATA_SPEED_3G
+			|(1<<IOMUXC_GPR13_SATA_PHY_6_SHIFT)
+			|IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED
+			|IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_12_16
+			|IOMUXC_GPR13_SATA_PHY_3_TXBOOST_3P33_DB
+			|IOMUXC_GPR13_SATA_PHY_2_TX_1P133V
+			|IOMUXC_GPR13_SATA_PHY_1_SLOW);
+
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	imx_iomux_v3_setup_multiple_pads(misc_pads,
+					 ARRAY_SIZE(misc_pads));
+
+	setup_iomux_uart();
+
+#if defined(CONFIG_VIDEO_IPUV3)
+	/* Set LDB clock to PLL2 PFD0 */
+	select_ldb_di_clock_source(MXC_PLL2_PFD0_CLK);
+#endif
+	return 0;
+}
+
+int board_init(void)
+{
+	gpio_direction_output(SUS_S3_OUT, 1);
+	gpio_direction_output(WIFI_EN, 1);
+#if defined(CONFIG_VIDEO_IPUV3)
+	setup_display();
+#endif
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_MXC_SPI
+	setup_spi();
+#endif
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd2",	 MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	{"sd3",	 MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+	/*
+	 * We need at least 200ms between power on and backlight on
+	 * as per specifications from CHI MEI
+	 */
+	mdelay(250);
+
+	/* enable backlight PWM 1 */
+	pwm_init(0, 0, 0);
+
+	/* duty cycle 5000000ns, period: 5000000ns */
+	pwm_config(0, 5000000, 5000000);
+
+	/* Backlight Power */
+	gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
+
+	pwm_enable(0);
+
+#ifdef CONFIG_CMD_SATA
+	setup_ba16_sata();
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	printf("BOARD: %s\n", CONFIG_BOARD_NAME);
+	return 0;
+}

board/advantech/dms-ba16/dms-ba16_1g.cfg new file +25 -0

new file mode 100644
index 0000000..d5de1fd
@@ -0,0 +1,25 @@
+/*
+ *
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+IMAGE_VERSION 2
+BOOT_FROM sd
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch/mx6-ddr.h"
+#include "asm/arch/iomux.h"
+#include "asm/arch/crm_regs.h"
+
+#include "ddr-setup.cfg"
+#include "micron-1g.cfg"
+#include "clocks.cfg"

board/advantech/dms-ba16/dms-ba16_2g.cfg new file +25 -0

new file mode 100644
index 0000000..a731af6
@@ -0,0 +1,25 @@
+/*
+ *
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+IMAGE_VERSION 2
+BOOT_FROM sd
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch/mx6-ddr.h"
+#include "asm/arch/iomux.h"
+#include "asm/arch/crm_regs.h"
+
+#include "ddr-setup.cfg"
+#include "samsung-2g.cfg"
+#include "clocks.cfg"

board/advantech/dms-ba16/micron-1g.cfg new file +63 -0

new file mode 100644
index 0000000..8cfefe2
@@ -0,0 +1,63 @@
+/* Calibrations */
+/* ZQ */
+DATA 4, MX6_MMDC_P0_MPZQHWCTRL,  0xa1390003
+/* write leveling */
+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
+/* Read DQS Gating calibration */
+DATA 4, MX6_MMDC_P0_MPDGCTRL0,   0x43480350
+DATA 4, MX6_MMDC_P0_MPDGCTRL1,   0x033C0340
+DATA 4, MX6_MMDC_P1_MPDGCTRL0,   0x43480350
+DATA 4, MX6_MMDC_P1_MPDGCTRL1,   0x03340314
+/* Read calibration */
+DATA 4, MX6_MMDC_P0_MPRDDLCTL,   0x382E2C32
+DATA 4, MX6_MMDC_P1_MPRDDLCTL,   0x38363044
+/* Write calibration */
+DATA 4 MX6_MMDC_P0_MPWRDLCTL,    0x3A38403A
+DATA 4 MX6_MMDC_P1_MPWRDLCTL,    0x4432483E
+/* read data bit delay */
+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
+
+/* Complete calibration by forced measurment */
+DATA 4, MX6_MMDC_P0_MPMUR0,	0x00000800
+DATA 4, MX6_MMDC_P1_MPMUR0,	0x00000800
+
+/* MMDC init */
+DATA 4, MX6_MMDC_P0_MDPDC,      0x00020036
+DATA 4, MX6_MMDC_P0_MDOTC,      0x09444040
+DATA 4, MX6_MMDC_P0_MDCFG0,     0x555A79A5
+DATA 4, MX6_MMDC_P0_MDCFG1,     0xDB538E64
+DATA 4, MX6_MMDC_P0_MDCFG2,     0x01ff00db
+DATA 4, MX6_MMDC_P0_MDMISC,     0x00001740
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00008000
+DATA 4, MX6_MMDC_P0_MDRWD,      0x000026d2
+DATA 4, MX6_MMDC_P0_MDOR,       0x005a1023
+DATA 4, MX6_MMDC_P0_MDASP,      0x00000027
+DATA 4, MX6_MMDC_P0_MDCTL,      0x831a0000
+
+/* Initialize memory */
+DATA 4, MX6_MMDC_P0_MDSCR,      0x04088032
+DATA 4, MX6_MMDC_P0_MDSCR,      0x0408803a
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00008033
+DATA 4, MX6_MMDC_P0_MDSCR,      0x0000803b
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00048031
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00048039
+DATA 4, MX6_MMDC_P0_MDSCR,      0x09408030
+DATA 4, MX6_MMDC_P0_MDSCR,      0x09408038
+DATA 4, MX6_MMDC_P0_MDSCR,      0x04008040
+DATA 4, MX6_MMDC_P0_MDSCR,      0x04008048
+DATA 4, MX6_MMDC_P0_MDREF,      0x00005800
+DATA 4, MX6_MMDC_P0_MPODTCTRL,  0x00033337
+DATA 4, MX6_MMDC_P1_MPODTCTRL,  0x00033337
+DATA 4, MX6_MMDC_P0_MDPDC,      0x00025576
+DATA 4, MX6_MMDC_P0_MAPSR,      0x00011006
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00000000

board/advantech/dms-ba16/samsung-2g.cfg new file +63 -0

new file mode 100644
index 0000000..4166cc9
@@ -0,0 +1,63 @@
+/* Calibrations */
+/* ZQ */
+DATA 4, MX6_MMDC_P0_MPZQHWCTRL,  0xa1390003
+/* write leveling */
+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
+/* Read DQS Gating calibration */
+DATA 4, MX6_MMDC_P0_MPDGCTRL0,   0x45380544
+DATA 4, MX6_MMDC_P0_MPDGCTRL1,   0x05280530
+DATA 4, MX6_MMDC_P1_MPDGCTRL0,   0x4530053C
+DATA 4, MX6_MMDC_P1_MPDGCTRL1,   0x0530050C
+/* Read calibration */
+DATA 4, MX6_MMDC_P0_MPRDDLCTL,   0x36303032
+DATA 4, MX6_MMDC_P1_MPRDDLCTL,   0x38363042
+/* Write calibration */
+DATA 4, MX6_MMDC_P0_MPWRDLCTL,   0x3A3A423E
+DATA 4, MX6_MMDC_P1_MPWRDLCTL,   0x4A38483E
+/* read data bit delay */
+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
+
+/* Complete calibration by forced measurment */
+DATA 4, MX6_MMDC_P0_MPMUR0,     0x00000800
+DATA 4, MX6_MMDC_P1_MPMUR0,     0x00000800
+
+/* MMDC init */
+DATA 4, MX6_MMDC_P0_MDPDC,      0x00020036
+DATA 4, MX6_MMDC_P0_MDOTC,      0x09444040
+DATA 4, MX6_MMDC_P0_MDCFG0,     0x8A8F79A4
+DATA 4, MX6_MMDC_P0_MDCFG1,     0xDB538E64
+DATA 4, MX6_MMDC_P0_MDCFG2,     0x01ff00db
+DATA 4, MX6_MMDC_P0_MDMISC,     0x00001740
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00008000
+DATA 4, MX6_MMDC_P0_MDRWD,      0x000026d2
+DATA 4, MX6_MMDC_P0_MDOR,       0x008F1023
+DATA 4, MX6_MMDC_P0_MDASP,      0x00000047
+DATA 4, MX6_MMDC_P0_MDCTL,      0x841a0000
+
+/* Initialize memory */
+DATA 4, MX6_MMDC_P0_MDSCR,      0x04088032
+DATA 4, MX6_MMDC_P0_MDSCR,      0x0408803a
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00008033
+DATA 4, MX6_MMDC_P0_MDSCR,      0x0000803b
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00408031
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00408039
+DATA 4, MX6_MMDC_P0_MDSCR,      0x09408030
+DATA 4, MX6_MMDC_P0_MDSCR,      0x09408038
+DATA 4, MX6_MMDC_P0_MDSCR,      0x04008040
+DATA 4, MX6_MMDC_P0_MDSCR,      0x04008048
+DATA 4, MX6_MMDC_P0_MDREF,      0x00005800
+DATA 4, MX6_MMDC_P0_MPODTCTRL,  0x00011117
+DATA 4, MX6_MMDC_P1_MPODTCTRL,  0x00011117
+DATA 4, MX6_MMDC_P0_MDPDC,      0x00025576
+DATA 4, MX6_MMDC_P0_MAPSR,      0x00011006
+DATA 4, MX6_MMDC_P0_MDSCR,      0x00000000

configs/dms-ba16-1g_defconfig new file +34 -0

new file mode 100644
index 0000000..a579af4
@@ -0,0 +1,34 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_ADVANTECH_DMS_BA16=y
+CONFIG_SYS_DDR_1G=y
+CONFIG_HUSH_PARSER=y
+CONFIG_BOOTDELAY=1
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_OF_LIBFDT=y
+CONFIG_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_G_DNL_MANUFACTURER="Advantech"
+CONFIG_G_DNL_VENDOR_NUM=0x0525
+CONFIG_G_DNL_PRODUCT_NUM=0xa4a5

configs/dms-ba16_defconfig new file +33 -0

new file mode 100644
index 0000000..365d05c
@@ -0,0 +1,33 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_ADVANTECH_DMS_BA16=y
+CONFIG_HUSH_PARSER=y
+CONFIG_BOOTDELAY=1
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_OF_LIBFDT=y
+CONFIG_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_G_DNL_MANUFACTURER="Advantech"
+CONFIG_G_DNL_VENDOR_NUM=0x0525
+CONFIG_G_DNL_PRODUCT_NUM=0xa4a5

include/configs/advantech_dms-ba16.h new file +315 -0

new file mode 100644
index 0000000..5108fa6
@@ -0,0 +1,315 @@
+/*
+ * Copyright (C) 2016 Timesys Corporation
+ * Copyright (C) 2016 Advantech Corporation
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __ADVANTECH_DMSBA16_CONFIG_H
+#define __ADVANTECH_DMSBA16_CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+#define CONFIG_BOARD_NAME	"Advantech DMS-BA16"
+#define CONFIG_DEFAULT_FDT_FILE	"imx6q-dms-ba16.dtb"
+
+#define CONFIG_MXC_UART_BASE	UART4_BASE
+#define CONFIG_CONSOLE_DEV	"ttymxc3"
+#define CONFIG_EXTRA_BOOTARGS	"panic=10"
+
+#define CONFIG_BOOT_DIR	""
+#define CONFIG_LOADCMD "fatload"
+#define CONFIG_RFSPART "2"
+
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+#include "mx6_common.h"
+#include <linux/sizes.h>
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_GPIO
+#define CONFIG_MXC_UART
+
+#define CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+
+/* SATA Configs */
+#define CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_DWC_AHSATA_PORT_ID	0
+#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR      0
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_DOS_PARTITION
+
+/* USB Configs */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+#define CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
+
+#define CONFIG_USBD_HS
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+
+/* Networking Configs */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_ETHPRIME		"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		4
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+/* Serial Flash */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_MXC_SPI
+#define CONFIG_SF_DEFAULT_BUS		0
+#define CONFIG_SF_DEFAULT_CS		0
+#define CONFIG_SF_DEFAULT_SPEED	20000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#endif
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_BAUDRATE	115200
+
+/* Command definition */
+#define CONFIG_CMD_BMODE
+
+#define CONFIG_LOADADDR	0x12000000
+#define CONFIG_SYS_TEXT_BASE	0x17800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=" CONFIG_BOOT_DIR "/uImage\0" \
+	"uboot=u-boot.imx\0" \
+	"fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_addr=0x18000000\0" \
+	"boot_fdt=yes\0" \
+	"ip_dyn=yes\0" \
+	"console=" CONFIG_CONSOLE_DEV "\0" \
+	"fdt_high=0xffffffff\0"	  \
+	"initrd_high=0xffffffff\0" \
+	"sddev=0\0" \
+	"emmcdev=1\0" \
+	"partnum=1\0" \
+	"loadcmd=" CONFIG_LOADCMD "\0" \
+	"rfspart=" CONFIG_RFSPART "\0" \
+	"update_sd_firmware=" \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"if mmc dev ${mmcdev}; then "	\
+			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
+				"setexpr fw_sz ${filesize} / 0x200; " \
+				"setexpr fw_sz ${fw_sz} + 1; "	\
+				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
+			"fi; "	\
+		"fi\0" \
+	"update_sf_uboot=" \
+		"if tftp $loadaddr $uboot; then " \
+			"sf probe; " \
+			"sf erase 0 0xC0000; " \
+			"sf write $loadaddr 0x400 $filesize; " \
+			"echo 'U-Boot upgraded. Please reset'; " \
+		"fi\0" \
+	"setargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
+	"loadbootscript=" \
+		"${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
+		" source\0" \
+	"loadimage=" \
+		"${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
+	"loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
+	"tryboot=" \
+		"if run loadbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run loadimage; then " \
+				"run doboot; " \
+			"fi; " \
+		"fi;\0" \
+	"doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
+		"run setargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootm ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootm; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootm; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootm ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootm; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootm; " \
+		"fi;\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	"usb start; " \
+	"setenv dev usb; " \
+	"setenv devnum 0; " \
+	"setenv rootdev sda${rfspart}; " \
+	"run tryboot; " \
+	\
+	"setenv dev mmc; " \
+	"setenv rootdev mmcblk0p${rfspart}; " \
+	\
+	"setenv devnum ${sddev}; " \
+	"if mmc dev ${devnum}; then " \
+		"run tryboot; " \
+		"setenv rootdev mmcblk1p${rfspart}; " \
+	"fi; " \
+	\
+	"setenv devnum ${emmcdev}; " \
+	"if mmc dev ${devnum}; then " \
+		"run tryboot; " \
+	"fi; " \
+	\
+	"bmode usb; " \
+
+#define CONFIG_ARP_TIMEOUT     200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START       0x10000000
+#define CONFIG_SYS_MEMTEST_END         0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
+
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE               (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS           1
+#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE                 (8 * 1024)
+#define CONFIG_ENV_OFFSET               (768 * 1024)
+#define CONFIG_ENV_SECT_SIZE            (64 * 1024)
+#define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#endif
+
+#define CONFIG_SYS_FSL_USDHC_NUM        3
+
+/* Framebuffer */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK                260000000
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK         66000000
+
+#undef CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#define CONFIG_PCIE_IMX_PERST_GPIO      IMX_GPIO_NR(7, 12)
+#define CONFIG_PCIE_IMX_POWER_GPIO      IMX_GPIO_NR(1, 5)
+#endif
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED            100000
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+
+#endif	/* __ADVANTECH_DMSBA16_CONFIG_H */

Hi Akshay,

this looks good to me. I apply it, and I let you think about an upgrade to SPL for this board.

Quoted 19 lines

source "board/ge/bx50v3/Kconfig"

arch/arm/cpu/armv7/mx6/Kconfig +1 -0

+source "board/advantech/dms-ba16/Kconfig"
 source "board/aristainetos/Kconfig"
 source "board/bachmann/ot1200/Kconfig"
 source "board/barco/platinum/Kconfig"

board/advantech/dms-ba16/Kconfig new file +8 -0

new file mode 100644
index 0000000..cc5b4e3
@@ -0,0 +1,27 @@
+choice
+	prompt "DDR Size"
+	default SYS_DDR_2G
+
+config SYS_DDR_1G
+	bool "1GiB"
+
+config SYS_DDR_2G

board/advantech/dms-ba16/Kconfig line 16

Quoted 8 lines

board/advantech/dms-ba16/Kconfig new file +8 -0

+	bool "2GiB"
+
+endchoice
+
+config IMX_CONFIG
+	default "board/advantech/dms-ba16/dms-ba16_2g.cfg" if SYS_DDR_2G
+	default "board/advantech/dms-ba16/dms-ba16_1g.cfg" if SYS_DDR_1G
+

Hi Akshay,

On 28/07/2016 12:12, Stefano Babic wrote:

Quoted 5 lines

Hi Akshay,

this looks good to me. I apply it, and I let you think about an upgrade to SPL for this board.

The patch breaks most of i.MX6 boards because it redefines IMX_CONFIG. In fact:

Quoted 10 lines · Stefano Babic

Hi Akshay,

Quoted 5 lines · Stefano Babic

Hi Akshay,

this looks good to me. I apply it, and I let you think about an upgrade to SPL for this board.

Quoted 3 lines

The patch breaks most of i.MX6 boards because it redefines IMX_CONFIG. In fact:

Thanks for finding this, fixed it in v3 Patch. The dms-ba16 Kconfig was missing a target check.

Once the target check was added, other boards
built correctly.