Idleness DRRS test
RFC 1/1 Idleness DRRS test
From: aknautiy <[email protected]>
Idleness DRRS:
By default the DRRS state will be at DRRS_HIGH_RR. When a Display content is Idle for more than 1Sec Idleness will be declared and DRRS_LOW_RR will be invoked, changing the refresh rate to the lower most refresh rate supported by the panel. As soon as there is a display content change there will be a DRRS state transition as DRRS_LOW_RR--> DRRS_HIGH_RR, changing the refresh rate to the highest refresh rate supported by the panel.
To test this, Idleness DRRS IGT will probe the DRRS state at below instances and compare with the expected state.
Instance Expected State
1. Immediately after rendering the still image DRRS_HIGH_RR
2. After a delay of 1.2Sec DRRS_LOW_RR
3. After changing the frame buffer DRRS_HIGH_RR
4. After a delay of 1.2Sec DRRS_LOW_RR
5. After changing the frame buffer DRRS_HIGH_RR
6. After a delay of 1.2Sec DRRS_LOW_RR
The test checks the driver DRRS state from the debugfs entry. To check the actual refresh-rate, a separate thread counts the number of vblanks received per sec. The refresh-rate calculated is checked against the expected refresh-rate with a tolerance value of 2.
This patch is a continuation of the earlier work
https://patchwork.freedesktop.org/patch/45472/ towards igt for idleness
DRRS. The code is tested on Broxton BXT_T platform.
--- tests/Makefile.sources | 1 + tests/kms_drrs.c | 614 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 615 insertions(+) create mode 100644 tests/kms_drrs.c
tests/Makefile.sources +1 -0
@@ -91,6 +91,7 @@ TESTS_progs_M = \ kms_cursor_crc \ kms_cursor_legacy \ kms_draw_crc \ + kms_drrs \ kms_fbc_crc \ kms_fbcon_fbt \ kms_flip \
tests/kms_drrs.c new file +614 -0
614 lines not on this page · raw message
Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 146 lines · Nautiyal Ankit
From: aknautiy <[email protected]>
Idleness DRRS:
By default the DRRS state will be atDRRS_HIGH_RR. When a Display content is Idle for more than 1Sec Idleness will be declared andDRRS_LOW_RRwill be invoked, changing the refresh rate to the lower most refresh rate supported by the panel. As soon as there is a display content change there will be a DRRS state transition as DRRS_LOW_RR-->DRRS_HIGH_RR, changing the refresh rate to the highest refresh rate supported by the panel.To test this, Idleness DRRS IGT will probe the DRRS state at below instances and compare with the expected state.
Instance Expected State
1. Immediately after rendering the still imageDRRS_HIGH_RR
2. After a delay of 1.2SecDRRS_LOW_RR
3. After changing the frame bufferDRRS_HIGH_RR
4. After a delay of 1.2SecDRRS_LOW_RR
5. After changing the frame bufferDRRS_HIGH_RR
6. After a delay of 1.2SecDRRS_LOW_RRThe test checks the driver DRRS state from the debugfs entry. To check the actual refresh-rate, a separate thread counts the number of vblanks received per sec. The refresh-rate calculated is checked against the expected refresh-rate with a tolerance value of 2.
This patch is a continuation of the earlier work
https://patchwork.freedesktop.org/patch/45472/ towards igt for idlenessDRRS. The code is tested on Broxton
BXT_Tplatform.Signed-off-by aknautiy <[email protected]>--- tests/Makefile.sources | 1 + tests/kms_drrs.c | 614 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 615 insertions(+) create mode 100644 tests/kms_drrs.ctests/Makefile.sources +1
-0@@ -91,6 +91,7 @@ TESTS_progs_M = \ kms_cursor_crc \ kms_cursor_legacy \ kms_draw_crc \ + kms_drrs \ kms_fbc_crc \ kms_fbcon_fbt \ kms_flip \tests/kms_drrs.c new file +89
-0@@ -0,0 +1,614 @@ +/* +* Copyright © 2016 Intel Corporation +* +* Permission is hereby granted, free of charge, to any person obtaining a +* copy of this software and associated documentation files (the "Software"), +* to deal in the Software without restriction, including without limitation +* the rights to use, copy, modify, merge, publish, distribute, sublicense, +* and/or sell copies of the Software, and to permit persons to whom the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including the next +* paragraph) shall be included in all copies or substantial portions of the +* Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS +* IN THE SOFTWARE. +* +*/ + +#include "drmtest.h" +#include "igt_debugfs.h" +#include "igt_kms.h" +#include "intel_chipset.h" +#include "intel_batchbuffer.h" +#include "ioctl_wrappers.h" +#include <time.h> +#include <pthread.h> +#include <stdlib.h> +#include <sys/time.h> +IGT_TEST_DESCRIPTION ( +"Performs write operations and then waits for DRRS to invoke the" +"Low Refresh Rate and then disturbs the contents of the screen once" +"again hence DRRS revert back to High Refresh Rate(Default)." ); + +#define DRRS_STATUS_BYTES_CNT 1000 +#define SET 1 +#define RESET 0 + +/* +* Structure to store data to create 2 framebuffers, fb[0] and fb[1] on a given +* display. To disturb the content of the screen, we replace fb[0] by fb[1] and +* vice versa. +*/ +typedef struct { +int drm_fd; +uint32_t devid; +uint32_t handle[2 ]; +igt_display_t display; +igt_output_t *output; +enum pipe pipe; +igt_plane_t *primary; +struct igt_fb fb[2 ]; +uint32_t fb_id[2 ]; +}data_t ; + +/* +* Structure to count vblank and note the starting time of the counter +*/ +typedef struct { +unsigned int vbl_count; +struct timeval start; +}vbl_info ; + +/* +* Condition variables,mutex, and shared variables for thread synchronization +*/ +pthread_mutex_t rr_mutex; +pthread_cond_t cv_rr_calc_requested; +pthread_cond_t cv_rr_calc_completed; +int rr_calc_requested =RESET ; +int rr_calc_completed =RESET ; +int thread_flag =SET ; +int refresh_rate_shared =-1 ; + +/* +* Structure for refresh rate type +*/ +typedef struct { +int rate; +const char *name; +}refresh_rate_t ; + +/* +* vblank_handler :
tests/kms_drrs.c line 99
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+* User defined vblank event handler, to count vblanks. +* The control reaches this function after a vblank event is registered +*/ +static void vblank_handler (int fd,unsigned int frame, +unsigned int sec,unsigned int usec,void *data) +{ +/* The control reaches this function after a vblank event is +* registered +*/ +vbl_info *info = data;
Doesn't this yell a warning?
Quoted 22 lines
tests/kms_drrs.c new file +22
-0+ +if (info ==NULL ) { +igt_info ("ERROR: Invalid Data passed to the vblank handler\n" ); +return ; + } + info->vbl_count++; +} + + +/* +* read_drrs_status : +* Func to read the DRRS status from debugfs +*/ +static bool read_drrs_status (data_t *data,char *str) +{ +FILE *status; +int cnt; + + status =igt_debugfs_fopen ("i915_drrs_status" ,"r" ); +igt_assert (status); + + cnt =fread (str,DRRS_STATUS_BYTES_CNT -1 ,1 , status);
tests/kms_drrs.c line 131
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+if (!cnt) { +if (!feof (status)) { +igt_info ("ERROR: %d at fread\n" ,ferror (status)); +return false; + } +clearerr (status); + } +fclose (status); +return true; +}
Can't find where data is used here.
Quoted 4 lines
tests/kms_drrs.c new file +4
-0+ +/* +* is_drrs_enabled : +* Func to check for DRRS support
tests/kms_drrs.c line 145
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+*/ +static bool is_drrs_enabled (data_t *data) +{ +char str[DRRS_STATUS_BYTES_CNT ] = {}; + +if (!read_drrs_status (data, str)) { +igt_info ("ERROR: Debugfs read FAILED\n" ); +return false; + } +return strstr (str,"DRRS Supported: Yes" ) !=NULL ;
No need for data here.
Quoted 15 lines
tests/kms_drrs.c new file +15
-0+} + +/* +* prepare_crtc : +* Func to prepare crtc for the given display +*/ +static bool prepare_crtc (data_t *data) +{ +if (data ==NULL ) +return false; +igt_display_t *display = &data->display; +igt_output_t *output = data->output; + +/* select the pipe we want to use */ +igt_output_set_pipe (output, data->pipe);
tests/kms_drrs.c line 170
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+igt_display_commit (display); + +if (!output->valid) { +igt_output_set_pipe (output,PIPE_ANY ); +igt_display_commit (display); +return false; + } + +return true; +}
The return value isn't used anywhere.
Quoted 61 lines
tests/kms_drrs.c new file +61
-0+ +/* +* calculate_refresh_rate : +* Func to calculate the refresh rate by counting +* vblanks in 1 sec. It returns the calculated refresh rate on success. +* Returns -1 in case of error. +*/ +int calculate_refresh_rate (data_t *data) +{ +drmEventContext evctx; +drmVBlank vbl; +vbl_info handler_info; +struct timeval start_time, curr_time; +double time_elapsed; +int refresh_rate =0 , vbl_count =0 ; +/*set up event context for handling vblank events*/ +memset (&evctx,0 ,sizeof (evctx)); + evctx.version =DRM_EVENT_CONTEXT_VERSION ; + evctx.vblank_handler = vblank_handler; + evctx.page_flip_handler =NULL ; + +/*initialize the vbl count to zero and set the starting time*/ + handler_info.vbl_count =0 ; +gettimeofday (&start_time,NULL ); + handler_info.start = start_time; + curr_time = start_time; + + time_elapsed =0.0 ; +/* To count vblanks in 1 sec. Loop till +* (current-time - starting time) <= 1.0 sec +*/ +while (time_elapsed <=1.0 ) { +int ret; + + vbl.request.type =DRM_VBLANK_RELATIVE |DRM_VBLANK_EVENT ; + vbl.request.sequence =1 ; + vbl.request.signal = (unsigned long )&handler_info; + ret =drmWaitVBlank (data->drm_fd, &vbl); +if (ret !=0 ) { +igt_info ("ERROR : drmWaitVBlank FAILED :%d\n" , ret); +return -1 ; + } +/*call drmHandleEvent() to handle vblank event */ + ret =drmHandleEvent (data->drm_fd, &evctx); +if (ret !=0 ) { +igt_info ("ERROR : drmHandleEvent FAILED %d\n" , ret); +return -1 ; + } + +gettimeofday (&curr_time,NULL ); + time_elapsed = curr_time.tv_sec + curr_time.tv_usec *1e-6 - + (start_time.tv_sec + start_time.tv_usec *1e-6 ); + } +if (!time_elapsed) { +igt_info ("ERROR: Incorrect measurement of vblank duration\n" ); +return -1 ; + } + vbl_count = handler_info.vbl_count; +/* calculate the refresh rate; rr=vblank_count/time_taken */ + refresh_rate = vbl_count / time_elapsed; +return refresh_rate;
tests/kms_drrs.c line 241
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+} + +/* +* worker_thread_func : +* Func which is run by a worker thread to calculate the refresh_rate, +* when signalled by the master thread. +*/ +void *worker_thread_func (void *ptr) +{ +data_t *data = ptr;
Isn't a typecast needed here?
Quoted 136 lines
tests/kms_drrs.c new file +136
-0+ +while (1 ) { +int refresh_rate =0 ; +/*wait for signal from master*/ +pthread_mutex_lock (&rr_mutex); +while (!rr_calc_requested) +pthread_cond_wait (&cv_rr_calc_requested, &rr_mutex); + +/* checkpoint for thread termination */ +if (thread_flag ==RESET ) { +pthread_mutex_unlock (&rr_mutex); +pthread_exit (NULL ); + } + rr_calc_requested =RESET ; +pthread_mutex_unlock (&rr_mutex); +/*calculate refresh_rate*/ + refresh_rate =calculate_refresh_rate (data); + +/* signal the master */ +pthread_mutex_lock (&rr_mutex); + refresh_rate_shared = refresh_rate; + rr_calc_completed =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_completed); + } +return NULL ; +} + +/* +* check_refresh_rate : +* Func to check the refresh rate calculated, against the expected refresh +* rate. It signals the worker thread to calculate the refresh- +* rate, and checks if the correct refresh rate is switched. +* Returns 1 in case of pass , 0 in case of failure, and -1 for error. +*/ + +static int check_refresh_rate (data_t *data,refresh_rate_t *expected_rr) +{ +/* +* The calculated refresh-rate is an approximation to estimated refresh-rate. +* The tolerance threshold for the difference is set to 2. Difference more than +* 2 is considered as failure for the check_refresh_rate. +*/ +#define TOLERANCE_THRESHOLD 2 +int ret, refresh_rate =-1 ; +char drrs_status[DRRS_STATUS_BYTES_CNT ] = {}; + +/* Signal worker thread to calculate refresh rate */ +pthread_mutex_lock (&rr_mutex); + rr_calc_requested =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_requested); + +/* Get the DRRS Status from the debugfs entry */ +if (!read_drrs_status (data, drrs_status)) { +igt_info ("ERROR : DRRS debugfs read FAILED\n" ); +return -1 ; + } +/* Wait for the refresh rate calculator thread */ +pthread_mutex_lock (&rr_mutex); +while (!rr_calc_completed) +pthread_cond_wait (&cv_rr_calc_completed, &rr_mutex); + rr_calc_completed =RESET ; + refresh_rate = refresh_rate_shared; +pthread_mutex_unlock (&rr_mutex); +if (refresh_rate <0 ) { +igt_info ("ERROR : Refresh rate calculation FAILED\n" ); +return -1 ; + } +igt_info ("INFO : Actual Refresh_rate based on Vblank Counts/sec = %d\n" + , refresh_rate); + +/* Compare with Expected Refresh Rate*/ +igt_info ("INFO: Expected Refresh-Rate %d\n" , expected_rr->rate); +if (strstr (drrs_status, expected_rr->name) !=NULL + &&abs (refresh_rate - expected_rr->rate) <=TOLERANCE_THRESHOLD ) { +igt_info ("INFO: Expected %s : PASSED\n" , expected_rr->name); +return 1 ; + } + +igt_info ("INFO : Expected %s : FAILED\n" , expected_rr->name); +return 0 ; +} + +/* +* clean_up : +* Func to stop the worker thread and destroy thread syncronization +* structures. +*/ +void clean_up (pthread_t rr_thread) +{ +/* Stop the worker thread */ +pthread_mutex_lock (&rr_mutex); + thread_flag =RESET ; + rr_calc_requested =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_requested); +pthread_join (rr_thread,NULL ); + +/* destroy the condition variables and mutex */ +pthread_cond_destroy (&cv_rr_calc_requested); +pthread_cond_destroy (&cv_rr_calc_completed); +pthread_mutex_destroy (&rr_mutex); +} + +/* +* execute_test: +* This function +* 1. Initializes the thread sync structures. +* 2. Creates a worker thread which can be signaled to estimate +* the refresh rates based on counting vblanks per sec. +* 3. Creates two different Framebuffer fb0, fb1 +* and apply them in the interval of 1.2Sec. So between FB change +* DRRS should toggle from DRRS_HIGH_RR -> DRRS_LOW_RR. +* And on next FB change DRRS_LOW_RR -> DRRS_HIGH_RR. +* +* These expected transistions are verified using the kernel debugfs +* and the refresh-rate, calculated by counting vblanks per sec by the +* worker thread. +*/ +static bool execute_test (data_t *data) +{ +igt_display_t *display = &data->display; +igt_output_t *output = data->output; +drmModeModeInfo *mode, *supported_modes; +bool test_failed = false; +int ret, i, count_modes; +refresh_rate_t high_rr, low_rr; +pthread_t rr_thread; + +/*initialize the condition variables and mutex*/ +pthread_cond_init (&cv_rr_calc_requested,NULL ); +pthread_cond_init (&cv_rr_calc_completed,NULL ); +pthread_mutex_init (&rr_mutex,NULL ); + thread_flag =SET ; + rr_calc_requested =RESET ;
tests/kms_drrs.c line 387
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+ rr_calc_completed =RESET ; +/* Create a thread for calculating the refresh rate */ + ret =pthread_create (&rr_thread,NULL , worker_thread_func, + (void *) data); +if (ret ==-1 ) { +igt_info ("ERROR : Refresh rate thread creation FAILED\n" ); +clean_up (rr_thread); +return false; + } +/*close the write end of the pipe as it will be used for reading only*/
Where is the write-end of the pipe?
Quoted 38 lines
tests/kms_drrs.c new file +38
-0+ + high_rr.name ="DRRS_HIGH_RR" ; + high_rr.rate =0 ; + low_rr.name ="DRRS_LOW_RR" ; + low_rr.rate =0 ; +/* get the max and min supported refresh rates for the display */ + supported_modes = output->config.connector->modes; + count_modes = output->config.connector->count_modes; +/* minimum 2 modes are required for DRRS */ +if (count_modes <2 ) { +igt_info ("ERROR: Minimum 2 modes required for DRRS\n" ); +return false; + } +for (i =0 ; i < count_modes; i++) { +int rr = supported_modes[i].vrefresh; + +if (i ==0 ) { + high_rr.rate = low_rr.rate = rr; +continue ; + } +if (high_rr.rate < rr) + high_rr.rate = rr; +if (low_rr.rate > rr) + low_rr.rate = rr; + } + data->primary =igt_output_get_plane (data->output,IGT_PLANE_PRIMARY ); + mode =igt_output_get_mode (data->output); + data->fb_id[0 ] =igt_create_color_fb (data->drm_fd, mode->hdisplay, + mode->vdisplay, +DRM_FORMAT_XRGB8888 , +LOCAL_DRM_FORMAT_MOD_NONE , +0.0 ,100.1 ,0.0 , &data->fb[0 ]); +igt_assert (data->fb_id[0 ]); + data->fb_id[1] = igt_create_color_fb(data->drm_fd, mode->hdisplay, + mode->vdisplay, + DRM_FORMAT_XRGB8888, + LOCAL_DRM_FORMAT_MOD_NONE, + 100.1, 0.0, 0.0,
tests/kms_drrs.c line 435
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+ &data->fb[1]); +igt_assert (data->fb_id[1 ]); + + data->handle[0 ] = data->fb[0 ].gem_handle; + data->handle[1 ] = data->fb[1 ].gem_handle; + +/* scanout = fb[1] */ +igt_plane_set_fb (data->primary, &data->fb[1 ]); +igt_display_commit (display); +
I assume that the behaviour is that once you have committed your frame-buffer, DRRS should be enabled by the kernel, hence the check here again. You do this (albeit manually) in igt_fixture block.
Quoted 39 lines
tests/kms_drrs.c new file +39
-0+if (!is_drrs_enabled (data)) { +igt_info ("INFO : DRRS not enabled\n" ); +igt_plane_set_fb (data->primary,NULL ); +igt_output_set_pipe (output,PIPE_ANY ); +igt_display_commit (display); + +igt_remove_fb (data->drm_fd, &data->fb[0 ]); +igt_remove_fb (data->drm_fd, &data->fb[1 ]); +clean_up (rr_thread); +return false; + } + +/* expecting High RR */ + ret =check_refresh_rate (data, &high_rr); +if (ret !=1 ) + test_failed = true; +/* 1.2Sec to Enter the Idleness and check for Low Refresh Rate */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret !=1 ) + test_failed = true; + +/* scanout = fb[0] and check for High Refresh Rate*/ +igt_plane_set_fb (data->primary, &data->fb[0 ]); +igt_display_commit (display); + ret =check_refresh_rate (data, &high_rr); +if (ret !=1 ) + test_failed = true; + +/* 1.2Sec to Enter the Idleness and check for Low Refresh Rate */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret !=1 ) + test_failed = true; + +/* scanout = fb[1] and check for High Refresh Rate*/ +igt_plane_set_fb (data->primary, &data->fb[1 ]); +igt_display_commit (display); + ret =check_refresh_rate (data, &high_rr);
tests/kms_drrs.c line 484
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+if (ret !=1 ) + test_failed = true; + +/* 1.2Sec to Enter the Idleness */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret !=1 ) + test_failed = true; + +igt_assert (!test_failed);
Do you really want to exit with an assert if DRRS test failed?
This function returns false when DRRS is not present and bails out earlier if test has failed. You might want to have returned an int with -1 for errors, 0 for test succeeded, 1 when test not succeeded (you seem to be using this notation in one of the functions above).
Quoted 44 lines
tests/kms_drrs.c new file +44
-0+clean_up (rr_thread); +return true; +} + +/* +* finish_crtc : +* Func to free the framebuffers after the test completion. +*/ +static void finish_crtc (data_t *data) +{ +igt_plane_set_fb (data->primary,NULL ); +igt_output_set_pipe (data->output,PIPE_ANY ); +igt_display_commit (&data->display); + +igt_remove_fb (data->drm_fd, &data->fb[0 ]); +igt_remove_fb (data->drm_fd, &data->fb[1 ]); +} + +/* +* reset_display : +* Func to reset the display structures after the test completion. +*/ +static void reset_display (data_t *data) +{ +igt_display_t *display = &data->display; + +for_each_connected_output (display, data->output) { +if (data->output->valid) { + data->primary =igt_output_get_plane (data->output, +IGT_PLANE_PRIMARY ); +igt_plane_set_fb (data->primary,NULL ); + } +igt_output_set_pipe (data->output,PIPE_ANY ); + } +} +/* +* run_test : +* Func to run the test for the eDP display. +*/ +static void run_test (data_t *data) +{ +igt_display_t *display = &data->display; +int valid_tests =0 ; +
tests/kms_drrs.c line 538
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+reset_display (data); +/* Check for eDP Connector on PIPE A ,as eDP goes normally on PIPE_A */ +for_each_connected_output (display, data->output) { +drmModeConnectorPtr c = data->output->config.connector; + +if (c->connector_type != DRM_MODE_CONNECTOR_eDP || + c->connection !=DRM_MODE_CONNECTED ) +continue ; + data->pipe =PIPE_A ; +prepare_crtc (data);
prepare_crtc() returns a bool.
Quoted 15 lines
tests/kms_drrs.c new file +15
-0+igt_info ("INFO : Beginning %s on pipe %s,connector %s\n" , +igt_subtest_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); + +if (!execute_test (data)) { +igt_info ("INFO :%s on pipe %s, connector %s:SKIPPED\n" , +igt_subtest_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); +continue ; + } + + valid_tests++; +
tests/kms_drrs.c line 563
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+igt_info ("INFO :%s on pipe %s, connector %s: PASSED\n" , +igt_subtest_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); + +finish_crtc (data); + } +} + +igt_main
Might want to use igt_simple_main for only one test.
Quoted 27 lines
tests/kms_drrs.c new file +27
-0+{ +data_t data = {}; + +igt_skip_on_simulation (); + + igt_fixture { +char buf[64 ]; +int cnt; +FILE *status; + + data.drm_fd =drm_open_driver_master (DRIVER_INTEL ); +if (data.drm_fd ==-1 ) { +igt_info ("ERROR : invalid fd\n" ); +return ; + } + + data.devid =intel_get_drm_devid (data.drm_fd); +if (data.devid <0 ) { +igt_info ("ERROR : invalid dev id\n" ); +return ; + } + + status =igt_debugfs_fopen ("i915_drrs_status" ,"r" ); +if (status ==NULL ) { +igt_info ("ERROR : debugfs open FAILED\n" ); +return ; + }
tests/kms_drrs.c line 600
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+igt_require_f (status,"No i915_drrs_status found\n" ); + cnt =fread (buf,sizeof (buf),1 , status); +if (!cnt) { +igt_info ("ERROR : fread FAILED\n" ); +return ; + } +fclose (status); + buf[sizeof (buf) -1 ] ='\0' ; +igt_require_f (!strstr (buf,"disabled" ), +"DRRS not supported:check VBT/panel caps\n" );
You have a couple functions to test DRRS presence bou do it (again) manually. Also you check for each connected output in you do it (again) manually.
tests/kms_drrs.c line 604
Quoted 3 lines
tests/kms_drrs.c new file +3
-0+/* Check if the DRRS is supported. +* If yes call the Idleness DRRS test +*/
This comments seems to belong in a different place.
Quoted 17 lines
tests/kms_drrs.c new file +10
-0+ +igt_display_init (&data.display, data.drm_fd); + } + igt_subtest_f("Idleness_DRRS") +run_test (&data); + + igt_fixture { +igt_display_fini (&data.display); + } +}Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Hi Marius,
Thanks for the comments and recommendations. I will be submitting the next version of the patch shortly with the changes.
PFB the actions taken/explanations inline.
Quoted 150 lines · Marius Vlad
Quoted 149 lines · Nautiyal Ankit
From: aknautiy <[email protected]>
Idleness DRRS:
By default the DRRS state will be atDRRS_HIGH_RR. When a Display content is Idle for more than 1Sec Idleness will be declared andDRRS_LOW_RRwill be invoked, changing the refresh rate to the lower most refresh rate supported by the panel. As soon as there is a display content change there will be a DRRS state transition as DRRS_LOW_RR-->DRRS_HIGH_RR, changing the refresh rate to the highest refresh rate supported by the panel.To test this, Idleness DRRS IGT will probe the DRRS state at below instances and compare with the expected state.
Instance Expected State
1. Immediately after rendering the still imageDRRS_HIGH_RR
2. After a delay of 1.2SecDRRS_LOW_RR
3. After changing the frame bufferDRRS_HIGH_RR
4. After a delay of 1.2SecDRRS_LOW_RR
5. After changing the frame bufferDRRS_HIGH_RR
6. After a delay of 1.2SecDRRS_LOW_RRThe test checks the driver DRRS state from the debugfs entry. To check the actual refresh-rate, a separate thread counts the number of vblanks received per sec. The refresh-rate calculated is checked against the expected refresh-rate with a tolerance value of 2.
This patch is a continuation of the earlier work
https://patchwork.freedesktop.org/patch/45472/ towards igt for idlenessDRRS. The code is tested on Broxton
BXT_Tplatform.Signed-off-by aknautiy <[email protected]>--- tests/Makefile.sources | 1 + tests/kms_drrs.c | 614 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 615 insertions(+)create mode 100644
tests/kms_drrs.ctests/Makefile.sources +1
-0@@ -91,6 +91,7 @@ TESTS_progs_M = \ kms_cursor_crc \ kms_cursor_legacy \ kms_draw_crc \ + kms_drrs \ kms_fbc_crc \ kms_fbcon_fbt \ kms_flip \tests/kms_drrs.c new file +92
-0@@ -0,0 +1,614 @@ +/* +* Copyright © 2016 Intel Corporation +* +* Permission is hereby granted, free of charge, to any person obtaining a +* copy of this software and associated documentation files (the "Software"), +* to deal in the Software without restriction, including without limitation +* the rights to use, copy, modify, merge, publish, distribute, sublicense, +* and/or sell copies of the Software, and to permit persons to whom the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including the next +* paragraph) shall be included in all copies or substantial portions of the +* Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS +* IN THE SOFTWARE. +* +*/ + +#include "drmtest.h" +#include "igt_debugfs.h" +#include "igt_kms.h" +#include "intel_chipset.h" +#include "intel_batchbuffer.h" +#include "ioctl_wrappers.h" +#include <time.h> +#include <pthread.h> +#include <stdlib.h> +#include <sys/time.h> +IGT_TEST_DESCRIPTION ( +"Performs write operations and then waits for DRRS to invoke the" +"Low Refresh Rate and then disturbs the contents of the screen once" +"again hence DRRS revert back to High Refresh Rate(Default)." ); + +#define DRRS_STATUS_BYTES_CNT 1000 +#define SET 1 +#define RESET 0 + +/* +* Structure to store data to create 2 framebuffers, fb[0] and fb[1] on a given +* display. To disturb the content of the screen, we replace fb[0] by fb[1] and +* vice versa. +*/ +typedef struct { +int drm_fd; +uint32_t devid; +uint32_t handle[2 ]; +igt_display_t display; +igt_output_t *output; +enum pipe pipe; +igt_plane_t *primary; +struct igt_fb fb[2 ]; +uint32_t fb_id[2 ]; +}data_t ; + +/* +* Structure to count vblank and note the starting time of the counter +*/ +typedef struct { +unsigned int vbl_count; +struct timeval start; +}vbl_info ; + +/* +* Condition variables,mutex, and shared variables for thread synchronization +*/ +pthread_mutex_t rr_mutex; +pthread_cond_t cv_rr_calc_requested; +pthread_cond_t cv_rr_calc_completed; +int rr_calc_requested =RESET ; +int rr_calc_completed =RESET ; +int thread_flag =SET ; +int refresh_rate_shared =-1 ; + +/* +* Structure for refresh rate type +*/ +typedef struct { +int rate; +const char *name; +}refresh_rate_t ; + +/* +* vblank_handler : +* User defined vblank event handler, to count vblanks. +* The control reaches this function after a vblank event is registered +*/
Quoted 8 lines
tests/kms_drrs.c line 99
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+static void vblank_handler (int fd,unsigned int frame, +unsigned int sec,unsigned int usec,void *data) +{ +/* The control reaches this function after a vblank event is +* registered +*/ +vbl_info *info = data;Doesn't this yell a warning?
Ankit- The type conversion is taken care of in the next patchset.
Quoted 25 lines
Quoted 25 lines
tests/kms_drrs.c new file +25
-0+ +if (info ==NULL ) { +igt_info ("ERROR: Invalid Data passed to the vblank handler\n" ); +return ; + } + info->vbl_count++; +} + + +/* +* read_drrs_status : +* Func to read the DRRS status from debugfs +*/ +static bool read_drrs_status (data_t *data,char *str) +{ +FILE *status; +int cnt; + + status =igt_debugfs_fopen ("i915_drrs_status" ,"r" ); +igt_assert (status); + + cnt =fread (str,DRRS_STATUS_BYTES_CNT -1 ,1 , status); +if (!cnt) { +if (!feof (status)) { +igt_info ("ERROR: %d at fread\n" ,ferror (status));
Quoted 8 lines
tests/kms_drrs.c line 131
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+return false; + } +clearerr (status); + } +fclose (status); +return true; +}Can't find where data is used here.
Ankit – Removed the unnecessary parameter :data_t from the function.
Quoted 7 lines
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+ +/* +* is_drrs_enabled : +* Func to check for DRRS support +*/ +static bool is_drrs_enabled (data_t *data) +{
Quoted 8 lines
tests/kms_drrs.c line 145
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+char str[DRRS_STATUS_BYTES_CNT ] = {}; + +if (!read_drrs_status (data, str)) { +igt_info ("ERROR: Debugfs read FAILED\n" ); +return false; + } +return strstr (str,"DRRS Supported: Yes" ) !=NULL ;No need for data here.
Ankit – Removed the unnecessary parameter :data_t from the function.
Quoted 18 lines
Quoted 18 lines
tests/kms_drrs.c new file +18
-0+} + +/* +* prepare_crtc : +* Func to prepare crtc for the given display +*/ +static bool prepare_crtc (data_t *data) +{ +if (data ==NULL ) +return false; +igt_display_t *display = &data->display; +igt_output_t *output = data->output; + +/* select the pipe we want to use */ +igt_output_set_pipe (output, data->pipe); +igt_display_commit (display); + +if (!output->valid) {
Quoted 8 lines
tests/kms_drrs.c line 170
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+igt_output_set_pipe (output,PIPE_ANY ); +igt_display_commit (display); +return false; + } + +return true; +}The return value isn't used anywhere.
Ankit- the return value is checked for successful prepare_crtc()
Quoted 64 lines
Quoted 64 lines
tests/kms_drrs.c new file +64
-0+ +/* +* calculate_refresh_rate : +* Func to calculate the refresh rate by counting +* vblanks in 1 sec. It returns the calculated refresh rate on success. +* Returns -1 in case of error. +*/ +int calculate_refresh_rate (data_t *data) +{ +drmEventContext evctx; +drmVBlank vbl; +vbl_info handler_info; +struct timeval start_time, curr_time; +double time_elapsed; +int refresh_rate =0 , vbl_count =0 ; +/*set up event context for handling vblank events*/ +memset (&evctx,0 ,sizeof (evctx)); + evctx.version =DRM_EVENT_CONTEXT_VERSION ; + evctx.vblank_handler = vblank_handler; + evctx.page_flip_handler =NULL ; + +/*initialize the vbl count to zero and set the starting time*/ + handler_info.vbl_count =0 ; +gettimeofday (&start_time,NULL ); + handler_info.start = start_time; + curr_time = start_time; + + time_elapsed =0.0 ; +/* To count vblanks in 1 sec. Loop till +* (current-time - starting time) <= 1.0 sec +*/ +while (time_elapsed <=1.0 ) { +int ret; + + vbl.request.type =DRM_VBLANK_RELATIVE |DRM_VBLANK_EVENT ; + vbl.request.sequence =1 ; + vbl.request.signal = (unsigned long )&handler_info; + ret =drmWaitVBlank (data->drm_fd, &vbl); +if (ret !=0 ) { +igt_info ("ERROR : drmWaitVBlank FAILED :%d\n" , ret); +return -1 ; + } +/*call drmHandleEvent() to handle vblank event */ + ret =drmHandleEvent (data->drm_fd, &evctx); +if (ret !=0 ) { +igt_info ("ERROR : drmHandleEvent FAILED %d\n" , ret); +return -1 ; + } + +gettimeofday (&curr_time,NULL ); + time_elapsed = curr_time.tv_sec + curr_time.tv_usec *1e-6 - + (start_time.tv_sec + start_time.tv_usec *1e-6 ); + } +if (!time_elapsed) { +igt_info ("ERROR: Incorrect measurement of vblank duration\n" ); +return -1 ; + } + vbl_count = handler_info.vbl_count; +/* calculate the refresh rate; rr=vblank_count/time_taken */ + refresh_rate = vbl_count / time_elapsed; +return refresh_rate; +} + +/*
Quoted 8 lines
tests/kms_drrs.c line 241
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+* worker_thread_func : +* Func which is run by a worker thread to calculate the refresh_rate, +* when signalled by the master thread. +*/ +void *worker_thread_func (void *ptr) +{ +data_t *data = ptr;Isn't a typecast needed here?
Ankit- Typecasted to data_t *
Quoted 139 lines
Quoted 139 lines
tests/kms_drrs.c new file +139
-0+ +while (1 ) { +int refresh_rate =0 ; +/*wait for signal from master*/ +pthread_mutex_lock (&rr_mutex); +while (!rr_calc_requested) +pthread_cond_wait (&cv_rr_calc_requested, &rr_mutex); + +/* checkpoint for thread termination */ +if (thread_flag ==RESET ) { +pthread_mutex_unlock (&rr_mutex); +pthread_exit (NULL ); + } + rr_calc_requested =RESET ; +pthread_mutex_unlock (&rr_mutex); +/*calculate refresh_rate*/ + refresh_rate =calculate_refresh_rate (data); + +/* signal the master */ +pthread_mutex_lock (&rr_mutex); + refresh_rate_shared = refresh_rate; + rr_calc_completed =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_completed); + } +return NULL ; +} + +/* +* check_refresh_rate : +* Func to check the refresh rate calculated, against the expected refresh +* rate. It signals the worker thread to calculate the refresh- +* rate, and checks if the correct refresh rate is switched. +* Returns 1 in case of pass , 0 in case of failure, and -1 for error. +*/ + +static int check_refresh_rate (data_t *data,refresh_rate_t *expected_rr) +{ +/* +* The calculated refresh-rate is an approximation to estimated refresh-rate. +* The tolerance threshold for the difference is set to 2. Difference more than +* 2 is considered as failure for the check_refresh_rate. +*/ +#define TOLERANCE_THRESHOLD 2 +int ret, refresh_rate =-1 ; +char drrs_status[DRRS_STATUS_BYTES_CNT ] = {}; + +/* Signal worker thread to calculate refresh rate */ +pthread_mutex_lock (&rr_mutex); + rr_calc_requested =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_requested); + +/* Get the DRRS Status from the debugfs entry */ +if (!read_drrs_status (data, drrs_status)) { +igt_info ("ERROR : DRRS debugfs read FAILED\n" ); +return -1 ; + } +/* Wait for the refresh rate calculator thread */ +pthread_mutex_lock (&rr_mutex); +while (!rr_calc_completed) +pthread_cond_wait (&cv_rr_calc_completed, &rr_mutex); + rr_calc_completed =RESET ; + refresh_rate = refresh_rate_shared; +pthread_mutex_unlock (&rr_mutex); +if (refresh_rate <0 ) { +igt_info ("ERROR : Refresh rate calculation FAILED\n" ); +return -1 ; + } +igt_info ("INFO : Actual Refresh_rate based on Vblank Counts/sec = %d\n" + , refresh_rate); + +/* Compare with Expected Refresh Rate*/ +igt_info ("INFO: Expected Refresh-Rate %d\n" , expected_rr->rate); +if (strstr (drrs_status, expected_rr->name) !=NULL + &&abs (refresh_rate - expected_rr->rate) <=TOLERANCE_THRESHOLD ) { +igt_info ("INFO: Expected %s : PASSED\n" , expected_rr->name); +return 1 ; + } + +igt_info ("INFO : Expected %s : FAILED\n" , expected_rr->name); +return 0 ; +} + +/* +* clean_up : +* Func to stop the worker thread and destroy thread syncronization +* structures. +*/ +void clean_up (pthread_t rr_thread) +{ +/* Stop the worker thread */ +pthread_mutex_lock (&rr_mutex); + thread_flag =RESET ; + rr_calc_requested =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_requested); +pthread_join (rr_thread,NULL ); + +/* destroy the condition variables and mutex */ +pthread_cond_destroy (&cv_rr_calc_requested); +pthread_cond_destroy (&cv_rr_calc_completed); +pthread_mutex_destroy (&rr_mutex); +} + +/* +* execute_test: +* This function +* 1. Initializes the thread sync structures. +* 2. Creates a worker thread which can be signaled to estimate +* the refresh rates based on counting vblanks per sec. +* 3. Creates two different Framebuffer fb0, fb1 +* and apply them in the interval of 1.2Sec. So between FB change +* DRRS should toggle from DRRS_HIGH_RR -> DRRS_LOW_RR. +* And on next FB change DRRS_LOW_RR -> DRRS_HIGH_RR. +* +* These expected transistions are verified using the kernel debugfs +* and the refresh-rate, calculated by counting vblanks per sec by the +* worker thread. +*/ +static bool execute_test (data_t *data) +{ +igt_display_t *display = &data->display; +igt_output_t *output = data->output; +drmModeModeInfo *mode, *supported_modes; +bool test_failed = false; +int ret, i, count_modes; +refresh_rate_t high_rr, low_rr; +pthread_t rr_thread; + +/*initialize the condition variables and mutex*/ +pthread_cond_init (&cv_rr_calc_requested,NULL ); +pthread_cond_init (&cv_rr_calc_completed,NULL ); +pthread_mutex_init (&rr_mutex,NULL ); + thread_flag =SET ; + rr_calc_requested =RESET ; + rr_calc_completed =RESET ; +/* Create a thread for calculating the refresh rate */ + ret = pthread_create(&rr_thread, NULL, worker_thread_func,
Quoted 8 lines
tests/kms_drrs.c line 387
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+ (void *) data); +if (ret ==-1 ) { +igt_info ("ERROR : Refresh rate thread creation FAILED\n" ); +clean_up (rr_thread); +return false; + } +/*close the write end of the pipe as it will be used for reading only*/ Where is the write-end of the pipe?
Ankit- Removed this comment.
Quoted 43 lines
Quoted 43 lines
tests/kms_drrs.c new file +43
-0+ + high_rr.name ="DRRS_HIGH_RR" ; + high_rr.rate =0 ; + low_rr.name ="DRRS_LOW_RR" ; + low_rr.rate =0 ; +/* get the max and min supported refresh rates for the display */ + supported_modes = output->config.connector->modes; + count_modes = output->config.connector->count_modes; +/* minimum 2 modes are required for DRRS */ +if (count_modes <2 ) { +igt_info ("ERROR: Minimum 2 modes required for DRRS\n" ); +return false; + } +for (i =0 ; i < count_modes; i++) { +int rr = supported_modes[i].vrefresh; + +if (i ==0 ) { + high_rr.rate = low_rr.rate = rr; +continue ; + } +if (high_rr.rate < rr) + high_rr.rate = rr; +if (low_rr.rate > rr) + low_rr.rate = rr; + } + data->primary =igt_output_get_plane (data->output,IGT_PLANE_PRIMARY ); + mode =igt_output_get_mode (data->output); + data->fb_id[0 ] =igt_create_color_fb (data->drm_fd, mode->hdisplay, + mode->vdisplay, +DRM_FORMAT_XRGB8888 , +LOCAL_DRM_FORMAT_MOD_NONE , +0.0 ,100.1 ,0.0 , &data->fb[0 ]); +igt_assert (data->fb_id[0 ]); + data->fb_id[1 ] =igt_create_color_fb (data->drm_fd, mode->hdisplay, + mode->vdisplay, +DRM_FORMAT_XRGB8888 , +LOCAL_DRM_FORMAT_MOD_NONE , +100.1 ,0.0 ,0.0 , + &data->fb[1 ]); +igt_assert (data->fb_id[1 ]); + + data->handle[0 ] = data->fb[0 ].gem_handle; + data->handle[1 ] = data->fb[1 ].gem_handle;
Quoted 8 lines
tests/kms_drrs.c line 435
Quoted 5 lines
tests/kms_drrs.c new file +5
-0+ +/* scanout = fb[1] */ +igt_plane_set_fb (data->primary, &data->fb[1 ]); +igt_display_commit (display); +I assume that the behaviour is that once you have committed your frame-buffer, DRRS should be enabled by the kernel, hence the check here again. You do this (albeit manually) in
igt_fixtureblock.
Ankit– Yes you are right. There are two things to be checked. 1st is whether DRRS is supported from VBT/Panel side, and this is checked in igt_simple_main. The 2nd thing is whether DRRS is enabled by the driver, checked once the framebuffer is committed.
Quoted 52 lines
Quoted 40 lines
tests/kms_drrs.c new file +39
-0+if (!is_drrs_enabled (data)) { +igt_info ("INFO : DRRS not enabled\n" ); +igt_plane_set_fb (data->primary,NULL ); +igt_output_set_pipe (output,PIPE_ANY ); +igt_display_commit (display); + +igt_remove_fb (data->drm_fd, &data->fb[0 ]); +igt_remove_fb (data->drm_fd, &data->fb[1 ]); +clean_up (rr_thread); +return false; + } + +/* expecting High RR */ + ret =check_refresh_rate (data, &high_rr); +if (ret !=1 ) + test_failed = true; +/* 1.2Sec to Enter the Idleness and check for Low Refresh Rate */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret !=1 ) + test_failed = true; + +/* scanout = fb[0] and check for High Refresh Rate*/ +igt_plane_set_fb (data->primary, &data->fb[0 ]); +igt_display_commit (display); + ret =check_refresh_rate (data, &high_rr); +if (ret !=1 ) + test_failed = true; + +/* 1.2Sec to Enter the Idleness and check for Low Refresh Rate */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret !=1 ) + test_failed = true; + +/* scanout = fb[1] and check for High Refresh Rate*/ +igt_plane_set_fb (data->primary, &data->fb[1 ]); +igt_display_commit (display); + ret =check_refresh_rate (data, &high_rr);tests/kms_drrs.c line 484
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+if (ret !=1 ) + test_failed = true; + +/* 1.2Sec to Enter the Idleness */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret !=1 ) + test_failed = true; + +igt_assert (!test_failed);Do you really want to exit with an assert if DRRS test failed?
Quoted 4 lines
This function returns false when DRRS is not present and bails out earlier if test has failed. You might want to have returned an int with -1 for errors, 0 for test succeeded, 1 when test not succeeded (you seem to be using this notation in one of the functions above).
Ankit- Returning int here, -1 for errors, 0 for test success and 1 for failure.
Quoted 48 lines
Quoted 48 lines
tests/kms_drrs.c new file +47
-0+clean_up (rr_thread); +return true; +} + +/* +* finish_crtc : +* Func to free the framebuffers after the test completion. +*/ +static void finish_crtc (data_t *data) +{ +igt_plane_set_fb (data->primary,NULL ); +igt_output_set_pipe (data->output,PIPE_ANY ); +igt_display_commit (&data->display); + +igt_remove_fb (data->drm_fd, &data->fb[0 ]); +igt_remove_fb (data->drm_fd, &data->fb[1 ]); +} + +/* +* reset_display : +* Func to reset the display structures after the test completion. +*/ +static void reset_display (data_t *data) +{ +igt_display_t *display = &data->display; + +for_each_connected_output (display, data->output) { +if (data->output->valid) { + data->primary =igt_output_get_plane (data->output, +IGT_PLANE_PRIMARY ); +igt_plane_set_fb (data->primary,NULL ); + } +igt_output_set_pipe (data->output,PIPE_ANY ); + } +} +/* +* run_test : +* Func to run the test for the eDP display. +*/ +static void run_test (data_t *data) +{ +igt_display_t *display = &data->display; +int valid_tests =0 ; + +reset_display (data); +/* Check for eDP Connector on PIPE A ,as eDP goes normally on PIPE_A */ +for_each_connected_output (display, data->output) {
Quoted 8 lines
tests/kms_drrs.c line 538
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+drmModeConnectorPtr c = data->output->config.connector; + +if (c->connector_type != DRM_MODE_CONNECTOR_eDP || + c->connection !=DRM_MODE_CONNECTED ) +continue ; + data->pipe =PIPE_A ; +prepare_crtc (data);
prepare_crtc()returns a bool.
Ankit- Return value is handled properly.
Quoted 18 lines
Quoted 18 lines
tests/kms_drrs.c new file +18
-0+igt_info ("INFO : Beginning %s on pipe %s,connector %s\n" , +igt_subtest_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); + +if (!execute_test (data)) { +igt_info ("INFO :%s on pipe %s, connector %s:SKIPPED\n" , +igt_subtest_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); +continue ; + } + + valid_tests++; + + igt_info("INFO :%s on pipe %s, connector %s: PASSED\n", + igt_subtest_name(), + kmstest_pipe_name(data->pipe),
Quoted 8 lines
tests/kms_drrs.c line 563
Quoted 7 lines
tests/kms_drrs.c new file +7
-0+ igt_output_name(data->output)); + +finish_crtc (data); + } +} + +igt_mainMight want to use
igt_simple_mainfor only one test.
Ankit – igt_simple_main is used.
Quoted 32 lines
Quoted 32 lines
tests/kms_drrs.c new file +32
-0+{ +data_t data = {}; + +igt_skip_on_simulation (); + + igt_fixture { +char buf[64 ]; +int cnt; +FILE *status; + + data.drm_fd =drm_open_driver_master (DRIVER_INTEL ); +if (data.drm_fd ==-1 ) { +igt_info ("ERROR : invalid fd\n" ); +return ; + } + + data.devid =intel_get_drm_devid (data.drm_fd); +if (data.devid <0 ) { +igt_info ("ERROR : invalid dev id\n" ); +return ; + } + + status =igt_debugfs_fopen ("i915_drrs_status" ,"r" ); +if (status ==NULL ) { +igt_info ("ERROR : debugfs open FAILED\n" ); +return ; + } +igt_require_f (status,"No i915_drrs_status found\n" ); + cnt =fread (buf,sizeof (buf),1 , status); +if (!cnt) { +igt_info ("ERROR : fread FAILED\n" ); +return ;
Quoted 8 lines
tests/kms_drrs.c line 600
Quoted 5 lines
tests/kms_drrs.c new file +5
-0+ } +fclose (status); + buf[sizeof (buf) -1 ] ='\0' ; +igt_require_f (!strstr (buf,"disabled" ), +"DRRS not supported:check VBT/panel caps\n" );You have a couple functions to test DRRS presence bou do it (again) manually. Also you check for each connected output in you do it (again) manually.
Ankit- Reusing the existing function is_drrs_enabled() for checking the DRRS support. However the function name was a misnomer, so changed it to is_drrs_supported.
Quoted 4 lines
tests/kms_drrs.c line 604
Quoted 3 lines
tests/kms_drrs.c new file +3
-0+/* Check if the DRRS is supported. +* If yes call the Idleness DRRS test +*/ This comments seems to belong in a different place.
Ankit- Added the comments in proper place.
Quoted 13 lines
Quoted 13 lines
tests/kms_drrs.c new file +10
-0+ +igt_display_init (&data.display, data.drm_fd); + } + igt_subtest_f("Idleness_DRRS") +run_test (&data); + + igt_fixture { +igt_display_fini (&data.display); + } +}Signature · 1 line
2.7.4
Quoted 4 lines
Quoted 4 lines
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Thanks for the comments , suggestions pointing out the misses. I will address these comments and send new version of the patch.
Regards,
Ankit
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v2 1/1 Idleness DRRS test
From: Ramalingam C <[email protected]>
Idleness DRRS:
By default the DRRS state will be at DRRS_HIGH_RR. When a Display content is Idle for more than 1Sec Idleness will be declared and DRRS_LOW_RR will be invoked, changing the refresh rate to the lower most refresh rate supported by the panel. As soon as there is a display content change there will be a DRRS state transition as DRRS_LOW_RR--> DRRS_HIGH_RR, changing the refresh rate to the highest refresh rate supported by the panel.
To test this, Idleness DRRS IGT will probe the DRRS state at below instances and compare with the expected state.
Instance Expected State
1. Immediately after rendering the still image DRRS_HIGH_RR
2. After a delay of 1.2Sec DRRS_LOW_RR
3. After changing the frame buffer DRRS_HIGH_RR
4. After a delay of 1.2Sec DRRS_LOW_RR
5. After changing the frame buffer DRRS_HIGH_RR
6. After a delay of 1.2Sec DRRS_LOW_RR
The test checks the driver DRRS state from the debugfs entry. To check the actual refresh-rate, a separate thread counts the number of vblanks received per sec. The refresh-rate calculated is checked against the expected refresh-rate with a tolerance value of 2.
This patch is a continuation of the earlier work
https://patchwork.freedesktop.org/patch/45472/ towards igt for idleness
DRRS. The code is tested on Broxton BXT_T platform.
v2: Addressed the comments and suggestions from Vlad, Marius. The signoff details from the earlier work are also included.
--- tests/Makefile.sources | 1 + tests/kms_drrs.c | 612 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 613 insertions(+) create mode 100644 tests/kms_drrs.c
tests/Makefile.sources +1 -0
@@ -91,6 +91,7 @@ TESTS_progs_M = \ kms_cursor_crc \ kms_cursor_legacy \ kms_draw_crc \ + kms_drrs \ kms_fbc_crc \ kms_fbcon_fbt \ kms_flip \
tests/kms_drrs.c new file +612 -0
612 lines not on this page · raw message
Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 281 lines · Nautiyal Ankit
From: Ramalingam C <[email protected]>
Idleness DRRS:
By default the DRRS state will be atDRRS_HIGH_RR. When a Display content is Idle for more than 1Sec Idleness will be declared andDRRS_LOW_RRwill be invoked, changing the refresh rate to the lower most refresh rate supported by the panel. As soon as there is a display content change there will be a DRRS state transition as DRRS_LOW_RR-->DRRS_HIGH_RR, changing the refresh rate to the highest refresh rate supported by the panel.To test this, Idleness DRRS IGT will probe the DRRS state at below instances and compare with the expected state.
Instance Expected State
1. Immediately after rendering the still imageDRRS_HIGH_RR
2. After a delay of 1.2SecDRRS_LOW_RR
3. After changing the frame bufferDRRS_HIGH_RR
4. After a delay of 1.2SecDRRS_LOW_RR
5. After changing the frame bufferDRRS_HIGH_RR
6. After a delay of 1.2SecDRRS_LOW_RRThe test checks the driver DRRS state from the debugfs entry. To check the actual refresh-rate, a separate thread counts the number of vblanks received per sec. The refresh-rate calculated is checked against the expected refresh-rate with a tolerance value of 2.
This patch is a continuation of the earlier work
https://patchwork.freedesktop.org/patch/45472/ towards igt for idlenessDRRS. The code is tested on Broxton
BXT_Tplatform.v2: Addressed the comments and suggestions from Vlad, Marius. The signoff details from the earlier work are also included.
Signed-off-by Ramalingam C <[email protected]>Signed-off-by Vandana Kannan <[email protected]>Signed-off-by aknautiy <[email protected]>--- tests/Makefile.sources | 1 + tests/kms_drrs.c | 612 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 613 insertions(+) create mode 100644 tests/kms_drrs.ctests/Makefile.sources +1
-0@@ -91,6 +91,7 @@ TESTS_progs_M = \ kms_cursor_crc \ kms_cursor_legacy \ kms_draw_crc \ + kms_drrs \ kms_fbc_crc \ kms_fbcon_fbt \ kms_flip \tests/kms_drrs.c new file +219
-0@@ -0,0 +1,612 @@ +/* +* Copyright © 2016 Intel Corporation +* +* Permission is hereby granted, free of charge, to any person obtaining a +* copy of this software and associated documentation files (the "Software"), +* to deal in the Software without restriction, including without limitation +* the rights to use, copy, modify, merge, publish, distribute, sublicense, +* and/or sell copies of the Software, and to permit persons to whom the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including the next +* paragraph) shall be included in all copies or substantial portions of the +* Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS +* IN THE SOFTWARE. +* +*/ + +#include "drmtest.h" +#include "igt_debugfs.h" +#include "igt_kms.h" +#include "intel_chipset.h" +#include "intel_batchbuffer.h" +#include "ioctl_wrappers.h" +#include <time.h> +#include <pthread.h> +#include <stdlib.h> +#include <sys/time.h> +IGT_TEST_DESCRIPTION ( +"Performs write operations and then waits for DRRS to invoke the" +"Low Refresh Rate and then disturbs the contents of the screen once" +"again hence DRRS revert back to High Refresh Rate(Default)." ); + +#define DRRS_STATUS_BYTES_CNT 1000 +#define SET 1 +#define RESET 0 + +/* +* Structure to store data to create 2 framebuffers, fb[0] and fb[1] on a given +* display. To disturb the content of the screen, we replace fb[0] by fb[1] and +* vice versa. +*/ +typedef struct { +int drm_fd; +uint32_t devid; +uint32_t handle[2 ]; +igt_display_t display; +igt_output_t *output; +enum pipe pipe; +igt_plane_t *primary; +struct igt_fb fb[2 ]; +uint32_t fb_id[2 ]; +}data_t ; + +/* +* Structure to count vblank and note the starting time of the counter +*/ +typedef struct { +unsigned int vbl_count; +struct timeval start; +}vbl_info ; + +/* +* Condition variables,mutex, and shared variables for thread synchronization +*/ +pthread_mutex_t rr_mutex; +pthread_cond_t cv_rr_calc_requested; +pthread_cond_t cv_rr_calc_completed; +int rr_calc_requested =RESET ; +int rr_calc_completed =RESET ; +int thread_flag =SET ; +int refresh_rate_shared =-1 ; + +/* +* Structure for refresh rate type +*/ +typedef struct { +int rate; +const char *name; +}refresh_rate_t ; + +/* +* vblank_handler : +* User defined vblank event handler, to count vblanks. +* The control reaches this function after a vblank event is registered +*/ +static void vblank_handler (int fd,unsigned int frame, +unsigned int sec,unsigned int usec,void *data) +{ +/* The control reaches this function after a vblank event is +* registered +*/ +vbl_info *info = (vbl_info *) data; + +if (info ==NULL ) { +igt_info ("ERROR: Invalid Data passed to the vblank handler\n" ); +return ; + } + info->vbl_count++; +} + + +/* +* read_drrs_status : +* Func to read the DRRS status from debugfs +*/ +static bool read_drrs_status (char *str) +{ +FILE *status; +int cnt; + + status =igt_debugfs_fopen ("i915_drrs_status" ,"r" ); +igt_assert (status); + + cnt =fread (str,DRRS_STATUS_BYTES_CNT -1 ,1 , status); +if (!cnt) { +if (!feof (status)) { +igt_info ("ERROR: %d at fread\n" ,ferror (status)); +return false; + } +clearerr (status); + } +fclose (status); +return true; +} + +/* +* is_drrs_supported : +* Func to check for DRRS support +*/ +static bool is_drrs_supported (void ) +{ +char str[DRRS_STATUS_BYTES_CNT ] = {}; + +if (!read_drrs_status (str)) { +igt_info ("ERROR: Debugfs read FAILED\n" ); +return false; + } +return strstr (str,"DRRS Supported: Yes" ) !=NULL ; +} + +/* +* is_drrs_enabled : +* Func to check if DRRS is enabled by driver +*/ +static bool is_drrs_enabled (void ) +{ +char str[DRRS_STATUS_BYTES_CNT ] = {}; + +if (!read_drrs_status (str)) { +igt_info ("ERROR: Debugfs read FAILED\n" ); +return false; + } +return strstr (str,"Idleness DRRS: Disabled" ) ==NULL ; +} + +/* +* prepare_crtc : +* Func to prepare crtc for the given display +*/ +static bool prepare_crtc (data_t *data) +{ +if (data ==NULL ) +return false; +igt_display_t *display = &data->display; +igt_output_t *output = data->output; + +/* select the pipe we want to use */ +igt_output_set_pipe (output, data->pipe); +igt_display_commit (display); + +if (!output->valid) { +igt_output_set_pipe (output,PIPE_ANY ); +igt_display_commit (display); +return false; + } + +return true; +} + +/* +* calculate_refresh_rate : +* Func to calculate the refresh rate by counting +* vblanks in 1 sec. It returns the calculated refresh rate on success. +* Returns -1 in case of error. +*/ +int calculate_refresh_rate (data_t *data) +{ +drmEventContext evctx; +drmVBlank vbl; +vbl_info handler_info; +struct timeval start_time, curr_time; +double time_elapsed; +int refresh_rate =0 , vbl_count =0 ; +/*set up event context for handling vblank events*/ +memset (&evctx,0 ,sizeof (evctx)); + evctx.version =DRM_EVENT_CONTEXT_VERSION ; + evctx.vblank_handler = vblank_handler; + evctx.page_flip_handler =NULL ; + +/*initialize the vbl count to zero and set the starting time*/ + handler_info.vbl_count =0 ; +gettimeofday (&start_time,NULL ); + handler_info.start = start_time; + curr_time = start_time; + + time_elapsed =0.0 ; +/* To count vblanks in 1 sec. Loop till +* (current-time - starting time) <= 1.0 sec +*/ +while (time_elapsed <=1.0 ) { +int ret; +
tests/kms_drrs.c line 229
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+ vbl.request.type =DRM_VBLANK_RELATIVE |DRM_VBLANK_EVENT ; + vbl.request.sequence =1 ; + vbl.request.signal = (unsigned long )&handler_info; + ret =drmWaitVBlank (data->drm_fd, &vbl); +if (ret !=0 ) { +igt_info ("ERROR : drmWaitVBlank FAILED :%d\n" , ret); +return -1 ; + } +/*call drmHandleEvent() to handle vblank event */ + ret =drmHandleEvent (data->drm_fd, &evctx);
Looks quite complicated. What you want is just
static double vbl_rate(const union drm_wait_vblank *start,
const union drm_wait_vblank *end)
{
double s, e;
s = start->reply.tval_sec + 1e-6*start->reply.tval_usec;
e = end->reply.tval_sec + 1e-6*end->reply.tval_usec;
return (end->reply.sequence - start->reply.sequnce) / (e - s);
}static int calculate_refresh_rate(int fd, int pipe, int period_ms)
{
union drm_wait_vblank start, end;
struct timeval tv;
memset(&start, 0, sizeof(start));
start.request.type = DRM_VBLANK_RELATIVE | pipe_select(pipe);
igt_assert(drmWaitVblank(fb, &start) == 0);
while (igt_milliseconds_elapsed(&tv) < period_ms) {
memset(&end, 0, sizeof(end));
end.request.type = DRM_VBLANK_RELATIVE | pipe_select(pipe);
end.sequence = 1;
igt_assert(drmWaitVblank(fb, &end) == 0);
}
return vbl_rate(&start, &end);
}right?
Call that igt_pipe_measure_vrefresh(int fd, enum pipe pipe, int min_period_ms);
or igt_crtc_measure_vrefresh(with igt_pipe_t instead of enum pipe).
and be done.
Quoted 44 lines
tests/kms_drrs.c new file +44
-0+if (ret !=0 ) { +igt_info ("ERROR : drmHandleEvent FAILED %d\n" , ret); +return -1 ; + } + +gettimeofday (&curr_time,NULL ); + time_elapsed = curr_time.tv_sec + curr_time.tv_usec *1e-6 - + (start_time.tv_sec + start_time.tv_usec *1e-6 ); + } +if (!time_elapsed) { +igt_info ("ERROR: Incorrect measurement of vblank duration\n" ); +return -1 ; + } + vbl_count = handler_info.vbl_count; +/* calculate the refresh rate; rr=vblank_count/time_taken */ + refresh_rate = vbl_count / time_elapsed; +return refresh_rate; +} + +/* +* worker_thread_func : +* Func which is run by a worker thread to calculate the refresh_rate, +* when signalled by the master thread. +*/ +void *worker_thread_func (void *ptr) +{ +data_t *data = (data_t *) ptr; + +while (1 ) { +int refresh_rate =0 ; +/*wait for signal from master*/ +pthread_mutex_lock (&rr_mutex); +while (!rr_calc_requested) +pthread_cond_wait (&cv_rr_calc_requested, &rr_mutex); + +/* checkpoint for thread termination */ +if (thread_flag ==RESET ) { +pthread_mutex_unlock (&rr_mutex); +pthread_exit (NULL ); + } + rr_calc_requested =RESET ; +pthread_mutex_unlock (&rr_mutex); +/*calculate refresh_rate*/ + refresh_rate =calculate_refresh_rate (data);
tests/kms_drrs.c line 283
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+ +/* signal the master */ +pthread_mutex_lock (&rr_mutex); + refresh_rate_shared = refresh_rate; + rr_calc_completed =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_completed); + } +return NULL ; +}
You are calculating the refresh rate synchronously, so what's the point of the thread?
You are serialising on this thread
tests/kms_drrs.c line 378
Quoted 2 lines
tests/kms_drrs.c new file +2
-0+static int execute_test (data_t *data) +{
Split up this monolith into separate subtests and groups thereof. -Chris
Signature · 5 lines
Chris Wilson, Intel Open Source Technology Centre _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Hi Chris,
Thanks for the comments.
I will try out the changes you have mentioned for counting vblanks.
For other comments please find the responses inline.
Quoted 324 lines · Chris Wilson
Quoted 281 lines · Nautiyal Ankit
From: Ramalingam C <[email protected]>
Idleness DRRS:
By default the DRRS state will be atDRRS_HIGH_RR. When a Display content is Idle for more than 1Sec Idleness will be declared andDRRS_LOW_RRwill be invoked, changing the refresh rate to the lower most refresh rate supported by the panel. As soon as there is a display content change there will be a DRRS state transition as DRRS_LOW_RR-->DRRS_HIGH_RR, changing the refresh rate to the highest refresh rate supported by the panel.To test this, Idleness DRRS IGT will probe the DRRS state at below instances and compare with the expected state.
Instance Expected State
1. Immediately after rendering the still imageDRRS_HIGH_RR
2. After a delay of 1.2SecDRRS_LOW_RR
3. After changing the frame bufferDRRS_HIGH_RR
4. After a delay of 1.2SecDRRS_LOW_RR
5. After changing the frame bufferDRRS_HIGH_RR
6. After a delay of 1.2SecDRRS_LOW_RRThe test checks the driver DRRS state from the debugfs entry. To check the actual refresh-rate, a separate thread counts the number of vblanks received per sec. The refresh-rate calculated is checked against the expected refresh-rate with a tolerance value of 2.
This patch is a continuation of the earlier work
https://patchwork.freedesktop.org/patch/45472/ towards igt for idlenessDRRS. The code is tested on Broxton
BXT_Tplatform.v2: Addressed the comments and suggestions from Vlad, Marius. The signoff details from the earlier work are also included.
Signed-off-by Ramalingam C <[email protected]>Signed-off-by Vandana Kannan <[email protected]>Signed-off-by aknautiy <[email protected]>--- tests/Makefile.sources | 1 + tests/kms_drrs.c | 612 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 613 insertions(+)create mode 100644
tests/kms_drrs.ctests/Makefile.sources +1
-0@@ -91,6 +91,7 @@ TESTS_progs_M = \ kms_cursor_crc \ kms_cursor_legacy \ kms_draw_crc \ + kms_drrs \ kms_fbc_crc \ kms_fbcon_fbt \ kms_flip \tests/kms_drrs.c new file +219
-0@@ -0,0 +1,612 @@ +/* +* Copyright © 2016 Intel Corporation +* +* Permission is hereby granted, free of charge, to any person obtaining a +* copy of this software and associated documentation files (the "Software"), +* to deal in the Software without restriction, including without limitation +* the rights to use, copy, modify, merge, publish, distribute, sublicense, +* and/or sell copies of the Software, and to permit persons to whom the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including the next +* paragraph) shall be included in all copies or substantial portions of the +* Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS +* IN THE SOFTWARE. +* +*/ + +#include "drmtest.h" +#include "igt_debugfs.h" +#include "igt_kms.h" +#include "intel_chipset.h" +#include "intel_batchbuffer.h" +#include "ioctl_wrappers.h" +#include <time.h> +#include <pthread.h> +#include <stdlib.h> +#include <sys/time.h> +IGT_TEST_DESCRIPTION ( +"Performs write operations and then waits for DRRS to invoke the" +"Low Refresh Rate and then disturbs the contents of the screen once" +"again hence DRRS revert back to High Refresh Rate(Default)." ); + +#define DRRS_STATUS_BYTES_CNT 1000 +#define SET 1 +#define RESET 0 + +/* +* Structure to store data to create 2 framebuffers, fb[0] and fb[1] on a given +* display. To disturb the content of the screen, we replace fb[0] by fb[1] and +* vice versa. +*/ +typedef struct { +int drm_fd; +uint32_t devid; +uint32_t handle[2 ]; +igt_display_t display; +igt_output_t *output; +enum pipe pipe; +igt_plane_t *primary; +struct igt_fb fb[2 ]; +uint32_t fb_id[2 ]; +}data_t ; + +/* +* Structure to count vblank and note the starting time of the counter +*/ +typedef struct { +unsigned int vbl_count; +struct timeval start; +}vbl_info ; + +/* +* Condition variables,mutex, and shared variables for thread synchronization +*/ +pthread_mutex_t rr_mutex; +pthread_cond_t cv_rr_calc_requested; +pthread_cond_t cv_rr_calc_completed; +int rr_calc_requested =RESET ; +int rr_calc_completed =RESET ; +int thread_flag =SET ; +int refresh_rate_shared =-1 ; + +/* +* Structure for refresh rate type +*/ +typedef struct { +int rate; +const char *name; +}refresh_rate_t ; + +/* +* vblank_handler : +* User defined vblank event handler, to count vblanks. +* The control reaches this function after a vblank event is registered +*/ +static void vblank_handler (int fd,unsigned int frame, +unsigned int sec,unsigned int usec,void *data) +{ +/* The control reaches this function after a vblank event is +* registered +*/ +vbl_info *info = (vbl_info *) data; + +if (info ==NULL ) { +igt_info ("ERROR: Invalid Data passed to the vblank handler\n" ); +return ; + } + info->vbl_count++; +} + + +/* +* read_drrs_status : +* Func to read the DRRS status from debugfs +*/ +static bool read_drrs_status (char *str) +{ +FILE *status; +int cnt; + + status =igt_debugfs_fopen ("i915_drrs_status" ,"r" ); +igt_assert (status); + + cnt =fread (str,DRRS_STATUS_BYTES_CNT -1 ,1 , status); +if (!cnt) { +if (!feof (status)) { +igt_info ("ERROR: %d at fread\n" ,ferror (status)); +return false; + } +clearerr (status); + } +fclose (status); +return true; +} + +/* +* is_drrs_supported : +* Func to check for DRRS support +*/ +static bool is_drrs_supported (void ) +{ +char str[DRRS_STATUS_BYTES_CNT ] = {}; + +if (!read_drrs_status (str)) { +igt_info ("ERROR: Debugfs read FAILED\n" ); +return false; + } +return strstr (str,"DRRS Supported: Yes" ) !=NULL ; +} + +/* +* is_drrs_enabled : +* Func to check if DRRS is enabled by driver +*/ +static bool is_drrs_enabled (void ) +{ +char str[DRRS_STATUS_BYTES_CNT ] = {}; + +if (!read_drrs_status (str)) { +igt_info ("ERROR: Debugfs read FAILED\n" ); +return false; + } +return strstr (str,"Idleness DRRS: Disabled" ) ==NULL ; +} + +/* +* prepare_crtc : +* Func to prepare crtc for the given display +*/ +static bool prepare_crtc (data_t *data) +{ +if (data ==NULL ) +return false; +igt_display_t *display = &data->display; +igt_output_t *output = data->output; + +/* select the pipe we want to use */ +igt_output_set_pipe (output, data->pipe); +igt_display_commit (display); + +if (!output->valid) { +igt_output_set_pipe (output,PIPE_ANY ); +igt_display_commit (display); +return false; + } + +return true; +} + +/* +* calculate_refresh_rate : +* Func to calculate the refresh rate by counting +* vblanks in 1 sec. It returns the calculated refresh rate on success. +* Returns -1 in case of error. +*/ +int calculate_refresh_rate (data_t *data) +{ +drmEventContext evctx; +drmVBlank vbl; +vbl_info handler_info; +struct timeval start_time, curr_time; +double time_elapsed; +int refresh_rate =0 , vbl_count =0 ; +/*set up event context for handling vblank events*/ +memset (&evctx,0 ,sizeof (evctx)); + evctx.version =DRM_EVENT_CONTEXT_VERSION ; + evctx.vblank_handler = vblank_handler; + evctx.page_flip_handler =NULL ; + +/*initialize the vbl count to zero and set the starting time*/ + handler_info.vbl_count =0 ; +gettimeofday (&start_time,NULL ); + handler_info.start = start_time; + curr_time = start_time; + + time_elapsed =0.0 ; +/* To count vblanks in 1 sec. Loop till +* (current-time - starting time) <= 1.0 sec +*/ +while (time_elapsed <=1.0 ) { +int ret; +tests/kms_drrs.c line 229
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+ vbl.request.type =DRM_VBLANK_RELATIVE |DRM_VBLANK_EVENT ; + vbl.request.sequence =1 ; + vbl.request.signal = (unsigned long )&handler_info; + ret =drmWaitVBlank (data->drm_fd, &vbl); +if (ret !=0 ) { +igt_info ("ERROR : drmWaitVBlank FAILED :%d\n" , ret); +return -1 ; + } +/*call drmHandleEvent() to handle vblank event */ + ret =drmHandleEvent (data->drm_fd, &evctx);Looks quite complicated. What you want is just
static double vbl_rate(const union
drm_wait_vblank*start,
const uniondrm_wait_vblank*end){ double s, e; s = start->reply.tval_sec + 1e-6*start->reply.tval_usec; e = end->reply.tval_sec + 1e-6*end->reply.tval_usec; return (end->reply.sequence - start->reply.sequnce) / (e - s); }static int
calculate_refresh_rate(int fd, int pipe, int period_ms){ union drm_wait_vblank start, end; struct timeval tv; memset(&start, 0, sizeof(start)); start.request.type = DRM_VBLANK_RELATIVE | pipe_select(pipe); igt_assert(drmWaitVblank(fb, &start) == 0); while (igt_milliseconds_elapsed(&tv) < period_ms) { memset(&end, 0, sizeof(end)); end.request.type = DRM_VBLANK_RELATIVE | pipe_select(pipe); end.sequence = 1; igt_assert(drmWaitVblank(fb, &end) == 0); } return vbl_rate(&start, &end); }
Quoted 7 lines
right?
Call that
igt_pipe_measure_vrefresh(int fd, enum pipe pipe, int min_period_ms);or
igt_crtc_measure_vrefresh(with igt_pipe_t instead of enum pipe).and be done.
I will try this out and get back to you.
Quoted 57 lines
Quoted 44 lines
tests/kms_drrs.c new file +44
-0+if (ret !=0 ) { +igt_info ("ERROR : drmHandleEvent FAILED %d\n" , ret); +return -1 ; + } + +gettimeofday (&curr_time,NULL ); + time_elapsed = curr_time.tv_sec + curr_time.tv_usec *1e-6 - + (start_time.tv_sec + start_time.tv_usec *1e-6 ); + } +if (!time_elapsed) { +igt_info ("ERROR: Incorrect measurement of vblank duration\n" ); +return -1 ; + } + vbl_count = handler_info.vbl_count; +/* calculate the refresh rate; rr=vblank_count/time_taken */ + refresh_rate = vbl_count / time_elapsed; +return refresh_rate; +} + +/* +* worker_thread_func : +* Func which is run by a worker thread to calculate the refresh_rate, +* when signalled by the master thread. +*/ +void *worker_thread_func (void *ptr) +{ +data_t *data = (data_t *) ptr; + +while (1 ) { +int refresh_rate =0 ; +/*wait for signal from master*/ +pthread_mutex_lock (&rr_mutex); +while (!rr_calc_requested) +pthread_cond_wait (&cv_rr_calc_requested, &rr_mutex); + +/* checkpoint for thread termination */ +if (thread_flag ==RESET ) { +pthread_mutex_unlock (&rr_mutex); +pthread_exit (NULL ); + } + rr_calc_requested =RESET ; +pthread_mutex_unlock (&rr_mutex); +/*calculate refresh_rate*/ + refresh_rate =calculate_refresh_rate (data);tests/kms_drrs.c line 283
Quoted 10 lines
tests/kms_drrs.c new file +10
-0+ +/* signal the master */ +pthread_mutex_lock (&rr_mutex); + refresh_rate_shared = refresh_rate; + rr_calc_completed =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_completed); + } +return NULL ; +}You are calculating the refresh rate synchronously, so what's the point of the thread?
Quoted 1 line
You are serialising on this thread
The DRRS status is verified in 2 ways.
One is through debugfs entry which checks the driver state [DRRS_HIGH / DRRS_LOW].
the other is by counting vblanks/sec for approximate refresh-rate.
As soon as we do a flip, the state is at DRRS_HIGH status, and panel displays at higher refresh rate.
The state goes to DRRS_LOW after waiting for 1.2 sec.
In this window of 1.2sec the main thread checks the state through debugfs, while the worker thread
counts the vblanks and calculates the approximate refresh rate in parallel.
The threads are synchronized so that master (after determining the driver state from debugfs),
waits for the worker thread to complete the refresh rate calculation, before proceeding with the test.
Quoted 3 lines
tests/kms_drrs.c line 378
Quoted 2 lines
tests/kms_drrs.c new file +2
-0+static int execute_test (data_t *data) +{Split up this monolith into separate subtests and groups thereof.
There are no sub-tests here, as we are flipping and checking the transition from high to low and low to high refresh rate. Flip [1.2 sec ](HIGH->LOW); Flip (LOW->HIGH); Flip [1.2 sec] (HIGH->LOW). This constitutes a single test.
Quoted 2 lines
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v3 1/1 Idleness DRRS test
From: Ramalingam C <[email protected]>
Idleness DRRS:
By default the DRRS state will be at DRRS_HIGH_RR. When a Display content is Idle for more than 1Sec Idleness will be declared and DRRS_LOW_RR will be invoked, changing the refresh rate to the lower most refresh rate supported by the panel. As soon as there is a display content change there will be a DRRS state transition as DRRS_LOW_RR--> DRRS_HIGH_RR, changing the refresh rate to the highest refresh rate supported by the panel.
To test this, Idleness DRRS IGT will probe the DRRS state at below instances and compare with the expected state.
Instance Expected State
1. Immediately after rendering the still image DRRS_HIGH_RR
2. After a delay of 1.2Sec DRRS_LOW_RR
3. After changing the frame buffer DRRS_HIGH_RR
4. After a delay of 1.2Sec DRRS_LOW_RR
5. After changing the frame buffer DRRS_HIGH_RR
6. After a delay of 1.2Sec DRRS_LOW_RR
The test checks the driver DRRS state from the debugfs entry. To check the actual refresh-rate, a separate thread counts the number of vblanks received per sec. The refresh-rate calculated is checked against the expected refresh-rate with a tolerance value of 2.
This patch is a continuation of the earlier work
https://patchwork.freedesktop.org/patch/45472/ towards igt for idleness
DRRS. The code is tested on Broxton BXT_T platform.
v2: Addressed the comments and suggestions from Vlad, Marius. The signoff details from the earlier work are also included.
v3: Modified vblank rate calculation by using reply-sequence, provided by drmWaitVBlank, as suggested by Chris Wilson.
--- tests/Makefile.sources | 1 + tests/kms_drrs.c | 599 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 600 insertions(+) create mode 100644 tests/kms_drrs.c
tests/Makefile.sources +1 -0
@@ -91,6 +91,7 @@ TESTS_progs_M = \ kms_cursor_crc \ kms_cursor_legacy \ kms_draw_crc \ + kms_drrs \ kms_fbc_crc \ kms_fbcon_fbt \ kms_flip \
tests/kms_drrs.c new file +599 -0
599 lines not on this page · raw message
Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Chris, happy with this revision?
Quoted 671 lines · Nautiyal Ankit
From: Ramalingam C <[email protected]>
Idleness DRRS:
By default the DRRS state will be atDRRS_HIGH_RR. When a Display content is Idle for more than 1Sec Idleness will be declared andDRRS_LOW_RRwill be invoked, changing the refresh rate to the lower most refresh rate supported by the panel. As soon as there is a display content change there will be a DRRS state transition as DRRS_LOW_RR-->DRRS_HIGH_RR, changing the refresh rate to the highest refresh rate supported by the panel.To test this, Idleness DRRS IGT will probe the DRRS state at below instances and compare with the expected state.
Instance Expected State
1. Immediately after rendering the still imageDRRS_HIGH_RR
2. After a delay of 1.2SecDRRS_LOW_RR
3. After changing the frame bufferDRRS_HIGH_RR
4. After a delay of 1.2SecDRRS_LOW_RR
5. After changing the frame bufferDRRS_HIGH_RR
6. After a delay of 1.2SecDRRS_LOW_RRThe test checks the driver DRRS state from the debugfs entry. To check the actual refresh-rate, a separate thread counts the number of vblanks received per sec. The refresh-rate calculated is checked against the expected refresh-rate with a tolerance value of 2.
This patch is a continuation of the earlier work
https://patchwork.freedesktop.org/patch/45472/ towards igt for idlenessDRRS. The code is tested on Broxton
BXT_Tplatform.v2: Addressed the comments and suggestions from Vlad, Marius. The signoff details from the earlier work are also included.
v3: Modified vblank rate calculation by using reply-sequence, provided by drmWaitVBlank, as suggested by Chris Wilson.
Signed-off-by Ramalingam C <[email protected]>Signed-off-by Vandana Kannan <[email protected]>Signed-off-by aknautiy <[email protected]>--- tests/Makefile.sources | 1 + tests/kms_drrs.c | 599 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 600 insertions(+) create mode 100644 tests/kms_drrs.ctests/Makefile.sources +1
-0@@ -91,6 +91,7 @@ TESTS_progs_M = \ kms_cursor_crc \ kms_cursor_legacy \ kms_draw_crc \ + kms_drrs \ kms_fbc_crc \ kms_fbcon_fbt \ kms_flip \tests/kms_drrs.c new file +599
-0@@ -0,0 +1,599 @@ +/* +* Copyright © 2016 Intel Corporation +* +* Permission is hereby granted, free of charge, to any person obtaining a +* copy of this software and associated documentation files (the "Software"), +* to deal in the Software without restriction, including without limitation +* the rights to use, copy, modify, merge, publish, distribute, sublicense, +* and/or sell copies of the Software, and to permit persons to whom the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including the next +* paragraph) shall be included in all copies or substantial portions of the +* Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS +* IN THE SOFTWARE. +* +*/ + +#include "drmtest.h" +#include "igt_debugfs.h" +#include "igt_kms.h" +#include "intel_chipset.h" +#include "intel_batchbuffer.h" +#include "ioctl_wrappers.h" +#include <time.h> +#include <pthread.h> +#include <stdlib.h> +#include <sys/time.h> +IGT_TEST_DESCRIPTION ( +"Performs write operations and then waits for DRRS to invoke the" +"Low Refresh Rate and then disturbs the contents of the screen once" +"again hence DRRS revert back to High Refresh Rate(Default)." ); + +#define DRRS_STATUS_BYTES_CNT 1000 +#define SET 1 +#define RESET 0 + +/* +* Structure to store data to create 2 framebuffers, fb[0] and fb[1] on a given +* display. To disturb the content of the screen, we replace fb[0] by fb[1] and +* vice versa. +*/ +typedef struct { +int drm_fd; +uint32_t devid; +uint32_t handle[2 ]; +igt_display_t display; +igt_output_t *output; +enum pipe pipe; +igt_plane_t *primary; +struct igt_fb fb[2 ]; +uint32_t fb_id[2 ]; +}data_t ; + +/* +* Structure to count vblank and note the starting time of the counter +*/ +typedef struct { +unsigned int vbl_count; +struct timeval start; +}vbl_info ; + +/* +* Condition variables,mutex, and shared variables for thread synchronization +*/ +pthread_mutex_t rr_mutex; +pthread_cond_t cv_rr_calc_requested; +pthread_cond_t cv_rr_calc_completed; +int rr_calc_requested =RESET ; +int rr_calc_completed =RESET ; +int thread_flag =SET ; +int refresh_rate_shared =-1 ; + +/* +* Structure for refresh rate type +*/ +typedef struct { +int rate; +const char *name; +}refresh_rate_t ; + +static inline uint32_t pipe_select (int pipe) +{ +if (pipe >1 ) +return pipe <<DRM_VBLANK_HIGH_CRTC_SHIFT ; +else if (pipe >0 ) +return DRM_VBLANK_SECONDARY ; +else +return 0 ; +} + +/* +* igt_millisec_elapsed: +* Calculates the no. of millisec elapsed since timeval start +*/ +static double igt_millisec_elapsed (const struct timeval *start) +{ +struct timeval curr; +double res; + +gettimeofday (&curr,NULL ); +return (1e6 *(curr.tv_sec - start->tv_sec) + + (curr.tv_usec - start->tv_usec)/1000.00 ); +} + +/* +* read_drrs_status : +* Func to read the DRRS status from debugfs +*/ +static bool read_drrs_status (char *str) +{ +FILE *status; +int cnt; + + status =igt_debugfs_fopen ("i915_drrs_status" ,"r" ); +igt_assert (status); + + cnt =fread (str,DRRS_STATUS_BYTES_CNT -1 ,1 , status); +if (!cnt) { +if (!feof (status)) { +igt_info ("ERROR: %d at fread\n" ,ferror (status)); +return false; + } +clearerr (status); + } +fclose (status); +return true; +} + +/* +* is_drrs_supported : +* Func to check for DRRS support +*/ +static bool is_drrs_supported (void ) +{ +char str[DRRS_STATUS_BYTES_CNT ] = {}; + +if (!read_drrs_status (str)) { +igt_info ("ERROR: Debugfs read FAILED\n" ); +return false; + } +return strstr (str,"DRRS Supported: Yes" ) !=NULL ; +} + +/* +* is_drrs_enabled : +* Func to check if DRRS is enabled by driver +*/ +static bool is_drrs_enabled (void ) +{ +char str[DRRS_STATUS_BYTES_CNT ] = {}; + +if (!read_drrs_status (str)) { +igt_info ("ERROR: Debugfs read FAILED\n" ); +return false; + } +return strstr (str,"Idleness DRRS: Disabled" ) ==NULL ; +} + +/* +* prepare_crtc : +* Func to prepare crtc for the given display +*/ +static bool prepare_crtc (data_t *data) +{ +if (data ==NULL ) +return false; + +igt_display_t *display = &data->display; +igt_output_t *output = data->output; + +/* select the pipe we want to use */ +igt_output_set_pipe (output, data->pipe); +igt_display_commit (display); + +if (!output->valid) { +igt_output_set_pipe (output,PIPE_ANY ); +igt_display_commit (display); +return false; + } + +return true; +} +/* +* vbl_rate : +* calculates the vblank rate by counting vblanks between start and end +* period, divided by time between start and end. +*/ +static double vbl_rate (const union drm_wait_vblank *start, +const union drm_wait_vblank *end) { +double s, e; + + s = start->reply.tval_sec +1e-6 * start->reply.tval_usec; + e = end->reply.tval_sec +1e-6 * end->reply.tval_usec; +return ((end->reply.sequence - start->reply.sequence) / (e - s)); +} + +/* +* calculate_refresh_rate : +* Func to calculate the refresh rate by counting +* vblanks in 1 sec (1000 ms). It returns the calculated refresh rate on +* success. Returns -1 in case of error. +*/ +int calculate_refresh_rate (data_t *data) +{ +#define PERIOD_MS 1000 +union drm_wait_vblank start, end; +struct timeval start_tv; + +memset (&start,0 ,sizeof (start)); + start.request.type =DRM_VBLANK_RELATIVE |pipe_select (data->pipe); +if (drmWaitVBlank (data->drm_fd, &start) !=0 ) { +igt_info ("ERROR : drmWaitVBlank Failed!\n" ); +return -1 ; + } +gettimeofday (&start_tv,NULL ); +while (igt_millisec_elapsed (&start_tv) <PERIOD_MS ) { +memset (&end,0 ,sizeof (end)); + end.request.type =DRM_VBLANK_RELATIVE | +pipe_select (data->pipe); + end.request.sequence =1 ; +if (drmWaitVBlank (data->drm_fd, &end) !=0 ) { +igt_info ("ERROR : drmWaitVBlank Failed!\n" ); +return -1 ; + } + } +return vbl_rate (&start, &end); +} + +/* +* worker_thread_func : +* Func which is run by a worker thread to calculate the refresh_rate, +* when signalled by the master thread. +*/ +void *worker_thread_func (void *ptr) +{ +data_t *data = (data_t *) ptr; + +while (1 ) { +int refresh_rate =0 ; +/*wait for signal from master*/ +pthread_mutex_lock (&rr_mutex); +while (!rr_calc_requested) +pthread_cond_wait (&cv_rr_calc_requested, &rr_mutex); + +/* checkpoint for thread termination */ +if (thread_flag ==RESET ) { +pthread_mutex_unlock (&rr_mutex); +pthread_exit (NULL ); + } + rr_calc_requested =RESET ; +pthread_mutex_unlock (&rr_mutex); +/*calculate refresh_rate*/ + refresh_rate =calculate_refresh_rate (data); + +/* signal the master */ +pthread_mutex_lock (&rr_mutex); + refresh_rate_shared = refresh_rate; + rr_calc_completed =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_completed); + } +return NULL ; +} + +/* +* check_refresh_rate : +* Func to check the refresh rate calculated, against the expected refresh +* rate. It signals the worker thread to calculate the refresh- +* rate, and checks if the correct refresh rate is switched. +* Returns 0 in case of pass , 1 in case of failure, and -1 for error. +*/ + +static int check_refresh_rate (data_t *data,refresh_rate_t *expected_rr) +{ +/* +* The calculated refresh-rate is an approximation to estimated refresh-rate. +* The tolerance threshold for the difference is set to 2. Difference more than +* 2 is considered as failure for the check_refresh_rate. +*/ +#define TOLERANCE_THRESHOLD 2 +int refresh_rate =-1 ; +char drrs_status[DRRS_STATUS_BYTES_CNT ] = {}; + +/* Signal worker thread to calculate refresh rate */ +pthread_mutex_lock (&rr_mutex); + rr_calc_requested =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_requested); + +/* Get the DRRS Status from the debugfs entry */ +if (!read_drrs_status (drrs_status)) { +igt_info ("ERROR : DRRS debugfs read FAILED\n" ); +return -1 ; + } +/* Wait for the refresh rate calculator thread */ +pthread_mutex_lock (&rr_mutex); +while (!rr_calc_completed) +pthread_cond_wait (&cv_rr_calc_completed, &rr_mutex); + rr_calc_completed =RESET ; + refresh_rate = refresh_rate_shared; +pthread_mutex_unlock (&rr_mutex); +if (refresh_rate <0 ) { +igt_info ("ERROR : Refresh rate calculation FAILED\n" ); +return -1 ; + } +igt_info ("INFO : Actual Refresh_rate based on Vblank Counts/sec = %d\n" + , refresh_rate); + +/* Compare with Expected Refresh Rate*/ +igt_info ("INFO: Expected Refresh-Rate %d\n" , expected_rr->rate); +if (strstr (drrs_status, expected_rr->name) !=NULL + &&abs (refresh_rate - expected_rr->rate) <=TOLERANCE_THRESHOLD ) { +igt_info ("INFO: Expected %s : PASSED\n" , expected_rr->name); +return 0 ; + } + +igt_info ("INFO : Expected %s : FAILED.\n" , expected_rr->name); +return 1 ; +} + +/* +* clean_up : +* Func to stop the worker thread and destroy thread syncronization +* structures. +*/ +void clean_up (pthread_t rr_thread) +{ +/* Stop the worker thread */ +pthread_mutex_lock (&rr_mutex); + thread_flag =RESET ; + rr_calc_requested =SET ; +pthread_mutex_unlock (&rr_mutex); +pthread_cond_signal (&cv_rr_calc_requested); +pthread_join (rr_thread,NULL ); + +/* destroy the condition variables and mutex */ +pthread_cond_destroy (&cv_rr_calc_requested); +pthread_cond_destroy (&cv_rr_calc_completed); +pthread_mutex_destroy (&rr_mutex); +} + +/* +* execute_test: +* This function +* 1. Initializes the thread sync structures. +* 2. Creates a worker thread which can be signaled to estimate +* the refresh rates based on counting vblanks per sec. +* 3. Creates two different Framebuffer fb0, fb1 +* and apply them in the interval of 1.2Sec. So between FB change +* DRRS should toggle from DRRS_HIGH_RR -> DRRS_LOW_RR. +* And on next FB change DRRS_LOW_RR -> DRRS_HIGH_RR. +* +* These expected transitions are verified using the kernel debugfs +* and the refresh-rate, calculated by counting vblanks per sec by the +* worker thread. +*/ +static int execute_test (data_t *data) +{ +igt_display_t *display = &data->display; +igt_output_t *output = data->output; +drmModeModeInfo *mode, *supported_modes; +int test_failed =0 ; +int ret, i, count_modes; +refresh_rate_t high_rr, low_rr; +pthread_t rr_thread; + +/*initialize the condition variables and mutex*/ +pthread_cond_init (&cv_rr_calc_requested,NULL ); +pthread_cond_init (&cv_rr_calc_completed,NULL ); +pthread_mutex_init (&rr_mutex,NULL ); + thread_flag =SET ; + rr_calc_requested =RESET ; + rr_calc_completed =RESET ; +/* create a thread for calculating the refresh rate */ + ret =pthread_create (&rr_thread,NULL , worker_thread_func, + (void *) data); +if (ret ==-1 ) { +igt_info ("ERROR : Refresh rate thread creation FAILED\n" ); +clean_up (rr_thread); +return -1 ; + } + + high_rr.name ="DRRS_HIGH_RR" ; + high_rr.rate =0 ; + low_rr.name ="DRRS_LOW_RR" ; + low_rr.rate =0 ; +/* get the max and min supported refresh rates for the display */ + supported_modes = output->config.connector->modes; + count_modes = output->config.connector->count_modes; +/* minimum 2 modes are required for DRRS */ +if (count_modes <2 ) { +igt_info ("ERROR: Minimum 2 modes required for DRRS\n" ); +return -1 ; + } +for (i =0 ; i < count_modes; i++) { +int rr = supported_modes[i].vrefresh; + +if (i ==0 ) { + high_rr.rate = low_rr.rate = rr; +continue ; + } +if (high_rr.rate < rr) + high_rr.rate = rr; +if (low_rr.rate > rr) + low_rr.rate = rr; + } + data->primary =igt_output_get_plane (data->output,IGT_PLANE_PRIMARY ); + mode =igt_output_get_mode (data->output); + data->fb_id[0 ] =igt_create_color_fb (data->drm_fd, mode->hdisplay, + mode->vdisplay, +DRM_FORMAT_XRGB8888 , +LOCAL_DRM_FORMAT_MOD_NONE , +0.0 ,100.1 ,0.0 , &data->fb[0 ]); +igt_assert (data->fb_id[0 ]); + data->fb_id[1 ] =igt_create_color_fb (data->drm_fd, mode->hdisplay, + mode->vdisplay, +DRM_FORMAT_XRGB8888 , +LOCAL_DRM_FORMAT_MOD_NONE , +100.1 ,0.0 ,0.0 , + &data->fb[1 ]); +igt_assert (data->fb_id[1 ]); + + data->handle[0 ] = data->fb[0 ].gem_handle; + data->handle[1 ] = data->fb[1 ].gem_handle; + +/* scanout = fb[1] */ +igt_plane_set_fb (data->primary, &data->fb[1 ]); +igt_display_commit (display); +if (!is_drrs_enabled ()) { +igt_info ("INFO : DRRS not enabled\n" ); +igt_plane_set_fb (data->primary,NULL ); +igt_output_set_pipe (output,PIPE_ANY ); +igt_display_commit (display); +igt_remove_fb (data->drm_fd, &data->fb[0 ]); +igt_remove_fb (data->drm_fd, &data->fb[1 ]); +clean_up (rr_thread); +return -1 ; + } + +/* expecting High RR */ + ret =check_refresh_rate (data, &high_rr); +if (ret ==-1 ) +return -1 ; +if (ret ==1 ) + test_failed =1 ; +/* 1.2Sec to Enter the Idleness and check for Low Refresh Rate */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret ==-1 ) +return -1 ; +if (ret ==1 ) + test_failed =1 ; + +/* scanout = fb[0] and check for High Refresh Rate*/ +igt_plane_set_fb (data->primary, &data->fb[0 ]); +igt_display_commit (display); + ret =check_refresh_rate (data, &high_rr); +if (ret ==-1 ) +return -1 ; +if (ret ==1 ) + test_failed =1 ; + +/* 1.2Sec to Enter the Idleness and check for Low Refresh Rate */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret ==-1 ) +return -1 ; +if (ret ==1 ) + test_failed =1 ; + +/* scanout = fb[1] and check for High Refresh Rate*/ +igt_plane_set_fb (data->primary, &data->fb[1 ]); +igt_display_commit (display); + ret =check_refresh_rate (data, &high_rr); +if (ret ==-1 ) +return -1 ; +if (ret ==1 ) + test_failed =1 ; + +/* 1.2Sec to Enter the Idleness */ +usleep (1200000 ); + ret =check_refresh_rate (data, &low_rr); +if (ret ==-1 ) +return -1 ; +if (ret ==1 ) + test_failed =1 ; + +clean_up (rr_thread); +return test_failed; +} + +/* +* finish_crtc : +* Func to free the framebuffers after the test completion. +*/ +static void finish_crtc (data_t *data) +{ +igt_plane_set_fb (data->primary,NULL ); +igt_output_set_pipe (data->output,PIPE_ANY ); +igt_display_commit (&data->display); + +igt_remove_fb (data->drm_fd, &data->fb[0 ]); +igt_remove_fb (data->drm_fd, &data->fb[1 ]); +} + +/* +* reset_display : +* Func to reset the display structures after the test completion. +*/ +static void reset_display (data_t *data) +{ +igt_display_t *display = &data->display; + +for_each_connected_output (display, data->output) { +if (data->output->valid) { + data->primary =igt_output_get_plane (data->output, +IGT_PLANE_PRIMARY ); +igt_plane_set_fb (data->primary,NULL ); + } +igt_output_set_pipe (data->output,PIPE_ANY ); + } +} +/* +* run_test : +* Func to run the test for the eDP display. +*/ +static void run_test (data_t *data) +{ +igt_display_t *display = &data->display; +int ret; + +reset_display (data); +/* Check for eDP Connector on PIPE A ,as eDP goes normally on PIPE_A */ +for_each_connected_output (display, data->output) { +drmModeConnectorPtr c = data->output->config.connector; + +if (c->connector_type != DRM_MODE_CONNECTOR_eDP || + c->connection !=DRM_MODE_CONNECTED ) +continue ; + data->pipe =PIPE_A ; +igt_assert_f (prepare_crtc (data),"Failed to prepare CRTC\n" ); +igt_info ("INFO : Beginning %s on pipe %s,connector %s\n" , +igt_test_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); + + ret =execute_test (data); +igt_skip_on_f (ret ==-1 , +"INFO :%s on pipe %s, connector %s:SKIPPED\n" , +igt_test_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); +igt_fail_on_f (ret ==1 , +"INFO :%s on pipe %s, connector %s:FAILED\n" , +igt_test_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); + +igt_assert_f (ret ==0 , +"INFO :%s on pipe %s, connector %s: PASSED\n" , +igt_test_name (), +kmstest_pipe_name (data->pipe), +igt_output_name (data->output)); + +finish_crtc (data); + } +} + +igt_simple_main +{ +data_t data = {}; + +igt_skip_on_simulation (); + data.drm_fd =drm_open_driver_master (DRIVER_INTEL ); +if (data.drm_fd ==-1 ) { +igt_info ("ERROR : invalid fd\n" ); +return ; + } + data.devid =intel_get_drm_devid (data.drm_fd); +if (data.devid <0 ) { +igt_info ("ERROR : invalid dev id\n" ); +return ; + } +/* Check if the DRRS is supported. +* If yes call the Idleness DRRS test +*/ +igt_require_f (is_drrs_supported (), +"DRRS not supported:check VBT/panel caps\n" ); +igt_display_init (&data.display, data.drm_fd); +run_test (&data); +igt_display_fini (&data.display); +}Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 1 line · Petri Latvala
Chris, happy with this revision?
Me? No. It still uses a thread instead of events, so I don't think it qualifies as a good example for anyone else wanting to do the same thing. Lots of hardcoded expectations (specific sleep patterns, rather than waiting for the kernel to change with a timeout for failure). It doesn't check all the possible ways that the output maybe changed (and if they are irrelevent, that too also needs to be tested to establish expected behaviour and catch future regressions). Important question, how is userspace expected to know that the vrefresh changed? How do get around that userspace is expecting a fixed vblank frequency?
-Chris
Signature · 5 lines
Chris Wilson, Intel Open Source Technology Centre _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 12 lines · Chris Wilson
Quoted 1 line · Petri Latvala
Chris, happy with this revision?
Me? No. It still uses a thread instead of events, so I don't think it qualifies as a good example for anyone else wanting to do the same thing. Lots of hardcoded expectations (specific sleep patterns, rather than waiting for the kernel to change with a timeout for failure). It doesn't check all the possible ways that the output maybe changed (and if they are irrelevent, that too also needs to be tested to establish expected behaviour and catch future regressions). Important question, how is userspace expected to know that the vrefresh changed? How do get around that userspace is expecting a fixed vblank frequency?
for display power testing we already have the kms_frontbuffer_tracking testcase, adding a DRRS variants to that one should resolve all this.
And then kms_drrs would be empty, except when we (if ever) do explicit drrs through modeset requests. And that would just be checking that the observed timings match the requested timings.
-Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
As per discussion with Chris, on IRC following were the suggestions :
- Chris has suggested an event based approach to avoid using pthreads.
- Avoid using kernel-specific info like transitional delays and instead use either polling or wait-for-event approach. Need to focus on user-observable behavior rather than the kernel standpoint.
- Check for transition latency is unnecessary in this test, as this is more of a performance/power benchmark.
I will try the event based mechanism to do away with pthreads, and incorporate these suggestions in the next patch-set.
-Ankit
Quoted 12 lines · Daniel Vetter
Quoted 11 lines · Chris Wilson
Quoted 1 line · Petri Latvala
Chris, happy with this revision?
Me? No. It still uses a thread instead of events, so I don't think it qualifies as a good example for anyone else wanting to do the same thing. Lots of hardcoded expectations (specific sleep patterns, rather than waiting for the kernel to change with a timeout for failure). It doesn't check all the possible ways that the output maybe changed (and if they are irrelevent, that too also needs to be tested to establish expected behaviour and catch future regressions). Important question, how is userspace expected to know that the vrefresh changed? How do get around that userspace is expecting a fixed vblank frequency?
Quoted 7 lines
for display power testing we already have the
kms_frontbuffer_trackingtestcase, adding a DRRS variants to that one should resolve all this.And then
kms_drrswould be empty, except when we (if ever) do explicit drrs through modeset requests. And that would just be checking that the observed timings match the requested timings.
-Daniel
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 8 lines · Ankit K
As per discussion with Chris, on IRC following were the suggestions :
- Chris has suggested an event based approach to avoid using pthreads.
- Avoid using kernel-specific info like transitional delays and instead use either polling or wait-for-event approach. Need to focus on user-observable behavior rather than the kernel standpoint.
Quoted 6 lines
- Check for transition latency is unnecessary in this test, as this is more of a performance/power benchmark.
I will try the event based mechanism to do away with pthreads, and incorporate these suggestions in the next patch-set.
Again, why is kms_frontbuffer_tracking not considered? Reinventing wheels is not good, and kms_frontbuffer_tracking implements all of the above stuff afaik.
-Daniel
Quoted 25 lines
-Ankit
Quoted 19 lines · Daniel Vetter
Quoted 11 lines · Chris Wilson
Quoted 1 line · Petri Latvala
Chris, happy with this revision?
Me? No. It still uses a thread instead of events, so I don't think it qualifies as a good example for anyone else wanting to do the same thing. Lots of hardcoded expectations (specific sleep patterns, rather than waiting for the kernel to change with a timeout for failure). It doesn't check all the possible ways that the output maybe changed (and if they are irrelevent, that too also needs to be tested to establish expected behaviour and catch future regressions). Important question, how is userspace expected to know that the vrefresh changed? How do get around that userspace is expecting a fixed vblank frequency?
for display power testing we already have the
kms_frontbuffer_trackingtestcase, adding a DRRS variants to that one should resolve all this.And then
kms_drrswould be empty, except when we (if ever) do explicit drrs through modeset requests. And that would just be checking that the observed timings match the requested timings.
-Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx