systemd configuration
I've switched to systemd, in a core-image-base build for an Atom (Cedartrail), and it boots fine. Now I want to make my own daemon start up. I'm new to systemd, and the way it seems to be set up is different from the way the systemd docs say it is usually set up.
The docs say that systemd, when booting up, usually activates a target called default.target, which is symlinked to either multi-user.target or graphical.target. (It would be the former in this GUI-less system.) Then, if I want to cause my daemon to be started, I would add a symlink to its systemd unit file to the .wants directory associated with multi-user.target.
But I can't find these things. They're not in the trees under /etc/systemd or /run/systemd. Oh, and when I do "systemctl list-unit-files", it shows both default.target and multi-user.target as disabled.
What makes this difficult to figure out is that the tools I have for perusing the target system are so primitive. There's no editor in the target that I'm aware of, and I can't network into the system and use an external editor to examine various files. So my question is this: is there someplace in build/tmp on my build system where the full target file system exists as a directory tree, so that I can pore through it and see how systemd is really configured?
Or perhaps someone can just tell me what target gets activated on bootup, where its .wants directory is, and what directory I should put my daemon's unit file into.
Signature · 2 lines
Ciao, Paul D. DeRocco Paul mailto:[email protected]
Quoted 12 lines · On Tuesday 02 July 2013 10:40:06 Paul D. DeRocco wrote:
I've switched to systemd, in a core-image-base build for an Atom (Cedartrail), and it boots fine. Now I want to make my own daemon start up. I'm new to systemd, and the way it seems to be set up is different from the way the systemd docs say it is usually set up.
The docs say that systemd, when booting up, usually activates a target called default.target, which is symlinked to either multi-user.target or graphical.target. (It would be the former in this GUI-less system.) Then, if I want to cause my daemon to be started, I would add a symlink to its systemd unit file to the .wants directory associated with multi-user.target.
Quoted 7 lines
But I can't find these things. They're not in the trees under
/etc/systemdor/run/systemd. Oh, and when I do "systemctl list-unit-files", it shows both default.target and multi-user.target as disabled.What makes this difficult to figure out is that the tools I have for perusing the target system are so primitive. There's no editor in the target that I'm aware of
That's entirely up to what you put into your image. busybox should provide a very basic version of "vi" out of the box.
Quoted 2 lines
, and I can't network into the system and use an external editor to examine various files.
Again, that's up to what you enable in the image. You could use NFS for example.
Quoted 4 lines
So my question is this: is there someplace
in build/tmp on my build system where the full target file system exists as a directory tree, so that I can pore through it and see how systemd is really configured?
Sure, you can find in the "rootfs" subdirectory of the image's WORKDIR (which you can find out using:
bitbake -e imagename | grep ^WORKDIR=
One way to look at this is to launch a devshell for the image:
bitbake -c devshell imagename
In 1.4+ using a devshell has the advantage of showing you the correct permission/ownership of files within the root filesystem.
Quoted 3 lines
Or perhaps someone can just tell me what target gets activated on bootup, where its .wants directory is, and what directory I should put my daemon's unit file into.
I'm sure someone more knowledgeable about systemd will pipe up with further information, but I would suggest looking at other recipes for examples. AFAICT systemd units for daemons should be installed into ${systemd_unitdir}/system.
Cheers,
Paul
Signature · 2 lines
Paul Eggleton Intel Open Source Technology Centre
Quoted 4 lines
From: Paul Eggleton [mailto:[email protected]]
That's entirely up to what you put into your image. busybox should provide a very basic version of "vi" out of the box.
Ah, vi. I guess it's time to learn vi.
Quoted 11 lines
Sure, you can find in the "rootfs" subdirectory of the image's WORKDIR (which you can find out using:
bitbake -e imagename | grep ^WORKDIR=
One way to look at this is to launch a devshell for the image:
bitbake -c devshell imagename
In 1.4+ using a devshell has the advantage of showing you the correct permission/ownership of files within the root filesystem.
For my purpose, the first choice turned out to be sufficient.
Quoted 11 lines
Quoted 4 lines
Or perhaps someone can just tell me what target gets activated on bootup,
where its .wants directory is, and what directory I should put my daemon's unit file into.I'm sure someone more knowledgeable about systemd will pipe up with further
information, but I would suggest looking at other recipes for examples. AFAICT
systemd units for daemons should be installed into ${systemd_unitdir}/system.
Turns out I was confused by the fact that there is no multi-user.target file, since it's just an empty unit. But there is a multi-user.target.wants directory, so I'm all set.
Signature · 2 lines
Ciao, Paul D. DeRocco Paul mailto:[email protected]