extcon: add Maxim MAX3355 driver
Subsystems (3)
PATCH v5 1/1 extcon: add Maxim MAX3355 driver
Maxim Integrated MAX3355E chip integrates a charge pump and comparators to enable a system with an integrated USB OTG dual-role transceiver to function as an USB OTG dual-role device. In addition to sensing/controlling Vbus, the chip also passes thru the ID signal from the USB OTG connector. On some Renesas boards, this signal is just fed into the SoC thru a GPIO pin -- there's no real OTG controller, only host and gadget USB controllers sharing the same USB bus; however, we'd like to allow host or gadget drivers to be loaded depending on the cable type, hence the need for the MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs (however, we aren't currently interested in them), the OFFVBUS# signal is controlled by the host controllers, there's also the SHDN# signal wired to a GPIO, it should be driven high for the normal operation.
---
Changes in version 5:
- removed unused variable in the probe() method;
- removed reference to the Koelsch board from the binding document;
- added Chanwoo Choi's ACK.
Changes in version 4:
- stopped calling kstrdup() for the device name;
- removed unneeded 'owner' field initializer;
- moved devm_extcon_allocate() call further down in the probe() method;
- extended the driver copyright;
- indented the continuation lines in the binding document.
Changes in version 3:
- reformatted the change log.
Changes in version 2:
- added the USB gadget cable support;
- added the remove() driver method which drives SHDN# GPIO low to save power;
- dropped vendor prefix from the ID GPIO property name;
- changed the GPIO property name suffix to "-gpios";
- switched to usign extcon_set_cable_state_() API;
- switched to using the gpiod/sleeping 'gpiolib' APIs;
- addded error messages to max3355_probe();
- added IRQF_NO_SUSPEND flasg to the devm_request_threaded_irq() call;
- renamed 'ret' variable to 'err' in max3355_probe();
- expanded the Kconfig entry help text;
- added vendor name to the patch summary, the bindings document, the Kconfig entry, the driver heading comment, the module description, and the change log;
- fixed up and reformatted the change log.
Documentation/devicetree/bindings/extcon/extcon-max3355.txt | 21 + drivers/extcon/Kconfig | 8 drivers/extcon/Makefile | 1 drivers/extcon/extcon-max3355.c | 150 ++++++++++++ 4 files changed, 180 insertions(+)
Documentation/devicetree/bindings/extcon/extcon-max3355.txt new file +21 -0
@@ -0,0 +1,21 @@ +Maxim Integrated MAX3355 USB OTG chip +------------------------------------- + +MAX3355 integrates a charge pump and comparators to enable a system with an +integrated USB OTG dual-role transceiver to function as a USB OTG dual-role +device. + +Required properties: +- compatible: should be "maxim,max3355"; +- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's SHDN# pin; +- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's ID_OUT pin. + +Example: + + usb-otg { + compatible = "maxim,max3355"; + maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; + };
drivers/extcon/Kconfig +8 -0
@@ -52,6 +52,14 @@ config EXTCON_MAX14577 Maxim MAX14577/77836. The MAX14577/77836 MUIC is a USB port accessory detector and switch. +config EXTCON_MAX3355 + tristate "Maxim MAX3355 USB OTG EXTCON Support" + help + If you say yes here you get support for the USB OTG role detection by + MAX3355. The MAX3355 chip integrates a charge pump and comparators to + enable a system with an integrated USB OTG dual-role transceiver to + function as an USB OTG dual-role device. + config EXTCON_MAX77693 tristate "Maxim MAX77693 EXTCON Support" depends on MFD_MAX77693 && INPUT
drivers/extcon/Makefile +1 -0
@@ -8,6 +8,7 @@ obj-$(CONFIG_EXTCON_ARIZONA) += extcon-a obj-$(CONFIG_EXTCON_AXP288) += extcon-axp288.o obj-$(CONFIG_EXTCON_GPIO) += extcon-gpio.o obj-$(CONFIG_EXTCON_MAX14577) += extcon-max14577.o +obj-$(CONFIG_EXTCON_MAX3355) += extcon-max3355.o obj-$(CONFIG_EXTCON_MAX77693) += extcon-max77693.o obj-$(CONFIG_EXTCON_MAX77843) += extcon-max77843.o obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o
drivers/extcon/extcon-max3355.c new file +150 -0
150 lines not on this page · raw message
Hi,
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.
drivers/extcon/Kconfig +1 -0
@@ -54,6 +54,7 @@ config EXTCON_MAX14577 config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TEST help If you say yes here you get support for the USB OTG role detection by MAX3355. The MAX3355 chip integrates a charge pump and comparators to
Thanks,
Chanwoo Choi
Quoted 271 lines · Sergei Shtylyov
Maxim Integrated MAX3355E chip integrates a charge pump and comparators to enable a system with an integrated USB OTG dual-role transceiver to function as an USB OTG dual-role device. In addition to sensing/controlling Vbus, the chip also passes thru the ID signal from the USB OTG connector. On some Renesas boards, this signal is just fed into the SoC thru a GPIO pin -- there's no real OTG controller, only host and gadget USB controllers sharing the same USB bus; however, we'd like to allow host or gadget drivers to be loaded depending on the cable type, hence the need for the MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs (however, we aren't currently interested in them), the OFFVBUS# signal is controlled by the host controllers, there's also the SHDN# signal wired to a GPIO, it should be driven high for the normal operation.
Signed-off-by Sergei Shtylyov <[email protected]>Acked-by Chanwoo Choi <[email protected]>---
Changes in version 5:
- removed unused variable in theprobe()method;
- removed reference to the Koelsch board from the binding document;
- added Chanwoo Choi's ACK.Changes in version 4:
- stopped callingkstrdup()for the device name;
- removed unneeded 'owner' field initializer;
- moveddevm_extcon_allocate()call further down in theprobe()method;
- extended the driver copyright;
- indented the continuation lines in the binding document.Changes in version 3:
- reformatted the change log.Changes in version 2:
- added the USB gadget cable support;
- added theremove()driver method which drives SHDN# GPIO low to save power;
- dropped vendor prefix from the ID GPIO property name;
- changed the GPIO property name suffix to "-gpios";
- switched to usignextcon_set_cable_state_()API;
- switched to using the gpiod/sleeping 'gpiolib' APIs;
- addded error messages tomax3355_probe();
- addedIRQF_NO_SUSPENDflasg to thedevm_request_threaded_irq()call;
- renamed 'ret' variable to 'err' inmax3355_probe();
- expanded theKconfigentry help text;
- added vendor name to the patch summary, the bindings document, theKconfigentry, the driver heading comment, the module description, and the change log;
- fixed up and reformatted the change log.Documentation/devicetree/bindings/extcon/extcon-max3355.txt | 21 + drivers/extcon/Kconfig | 8 drivers/extcon/Makefile | 1 drivers/extcon/extcon-max3355.c | 150 ++++++++++++ 4 files changed, 180 insertions(+)Index:
extcon/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
===================================================================Documentation/devicetree/bindings/extcon/extcon-max3355.txt new file +21
-0@@ -0,0 +1,21 @@ +Maxim Integrated MAX3355 USB OTG chip +------------------------------------- + +MAX3355 integrates a charge pump and comparators to enable a system with an +integrated USB OTG dual-role transceiver to function as a USB OTG dual-role +device. + +Required properties: +- compatible: should be "maxim,max3355"; +- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's SHDN# pin; +- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's ID_OUT pin. + +Example: + + usb-otg { + compatible = "maxim,max3355"; + maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; + };Index: extcon/drivers/extcon/Kconfig
===================================================================drivers/extcon/Kconfig +8
-0@@ -52,6 +52,14 @@ config EXTCON_MAX14577 Maxim MAX14577/77836. The MAX14577/77836 MUIC is a USB port accessory detector and switch. +config EXTCON_MAX3355 + tristate "Maxim MAX3355 USB OTG EXTCON Support" + help + If you say yes here you get support for the USB OTG role detection by + MAX3355. The MAX3355 chip integrates a charge pump and comparators to + enable a system with an integrated USB OTG dual-role transceiver to + function as an USB OTG dual-role device. + config EXTCON_MAX77693 tristate "Maxim MAX77693 EXTCON Support" depends on MFD_MAX77693 && INPUTIndex: extcon/drivers/extcon/Makefile
===================================================================drivers/extcon/Makefile +1
-0@@ -8,6 +8,7 @@ obj-$(CONFIG_EXTCON_ARIZONA) += extcon-a obj-$(CONFIG_EXTCON_AXP288) += extcon-axp288.o obj-$(CONFIG_EXTCON_GPIO) += extcon-gpio.o obj-$(CONFIG_EXTCON_MAX14577) += extcon-max14577.o +obj-$(CONFIG_EXTCON_MAX3355) += extcon-max3355.o obj-$(CONFIG_EXTCON_MAX77693) += extcon-max77693.o obj-$(CONFIG_EXTCON_MAX77843) += extcon-max77843.o obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.oIndex:
extcon/drivers/extcon/extcon-max3355.c
===================================================================drivers/extcon/extcon-max3355.c new file +150
-1@@ -0,0 +1,150 @@ +/* +* Maxim Integrated MAX3355 USB OTG chip extcon driver +* +* Copyright (C) 2014-2015 Cogent Embedded, Inc. +* Author: Sergei Shtylyov <[email protected]> +* +* This software is licensed under the terms of the GNU General Public +* License version 2, as published by the Free Software Foundation, and +* may be copied, distributed, and modified under those terms. +*/ + +#include <linux/extcon.h> +#include <linux/gpio.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of_gpio.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/workqueue.h> + +struct max3355_data { +struct extcon_dev *edev; +struct gpio_desc *id_gpiod; +struct gpio_desc *shdn_gpiod; +}; + +static const unsigned int max3355_cable[] = { +EXTCON_USB , +EXTCON_USB_HOST , +EXTCON_NONE , +}; + +static irqreturn_t max3355_id_irq (int irq,void *dev_id) +{ +struct max3355_data *data = dev_id; +int id =gpiod_get_value_cansleep (data->id_gpiod); + +if (id) { +/* +* ID = 1 means USB HOST cable detached. +* As we don't have event for USB peripheral cable attached, +* we simulate USB peripheral attach here. +*/ +extcon_set_cable_state_ (data->edev,EXTCON_USB_HOST , false); +extcon_set_cable_state_ (data->edev,EXTCON_USB , true); + }else { +/* +* ID = 0 means USB HOST cable attached. +* As we don't have event for USB peripheral cable detached, +* we simulate USB peripheral detach here. +*/ +extcon_set_cable_state_ (data->edev,EXTCON_USB , false); +extcon_set_cable_state_ (data->edev,EXTCON_USB_HOST , true); + } + +return IRQ_HANDLED ; +} + +static int max3355_probe (struct platform_device *pdev) +{ +struct max3355_data *data; +struct gpio_desc *gpiod; +int irq, err; + + data =devm_kzalloc (&pdev->dev,sizeof (struct max3355_data ), +GFP_KERNEL ); +if (!data) +return -ENOMEM ; + + gpiod =devm_gpiod_get (&pdev->dev,"id" ,GPIOD_IN ); +if (IS_ERR (gpiod)) { +dev_err (&pdev->dev,"failed to get ID_OUT GPIO\n" ); +return PTR_ERR (gpiod); + } + data->id_gpiod = gpiod; + + gpiod =devm_gpiod_get (&pdev->dev,"maxim,shdn" ,GPIOD_OUT_HIGH ); +if (IS_ERR (gpiod)) { +dev_err (&pdev->dev,"failed to get SHDN# GPIO\n" ); +return PTR_ERR (gpiod); + } + data->shdn_gpiod = gpiod; + + data->edev =devm_extcon_dev_allocate (&pdev->dev, max3355_cable); +if (IS_ERR (data->edev)) { +dev_err (&pdev->dev,"failed to allocate extcon device\n" ); +return PTR_ERR (data->edev); + } + + err =devm_extcon_dev_register (&pdev->dev, data->edev); +if (err <0 ) { +dev_err (&pdev->dev,"failed to register extcon device\n" ); +return err; + } + + irq =gpiod_to_irq (data->id_gpiod); +if (irq <0 ) { +dev_err (&pdev->dev,"failed to translate ID_OUT GPIO to IRQ\n" ); +return irq; + } + + err =devm_request_threaded_irq (&pdev->dev, irq,NULL , max3355_id_irq, +IRQF_ONESHOT |IRQF_NO_SUSPEND | +IRQF_TRIGGER_RISING | +IRQF_TRIGGER_FALLING , + pdev->name, data); +if (err <0 ) { +dev_err (&pdev->dev,"failed to request ID_OUT IRQ\n" ); +return err; + } + +platform_set_drvdata (pdev, data); + +/* Perform initial detection */ +max3355_id_irq (irq, data); + +return 0 ; +} + +static int max3355_remove (struct platform_device *pdev) +{ +struct max3355_data *data =platform_get_drvdata (pdev); + +gpiod_set_value_cansleep (data->shdn_gpiod,0 ); + +return 0 ; +} + +static const struct of_device_id max3355_match_table[] = { + { .compatible ="maxim,max3355" , }, + { } +}; +MODULE_DEVICE_TABLE (of, max3355_match_table); + +static struct platform_driver max3355_driver = { + .probe = max3355_probe, + .remove = max3355_remove, + .driver = { + .name ="extcon-max3355" , + .of_match_table = max3355_match_table, + }, +}; + +module_platform_driver (max3355_driver); + +MODULE_AUTHOR ("Sergei Shtylyov <[email protected]>" ); +MODULE_DESCRIPTION ("Maxim MAX3355 extcon driver" ); +MODULE_LICENSE ("GPL v2" ); --To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Hello.
drivers/extcon/Kconfig config EXTCON_MAX14577 · line 57
Quoted 12 lines · Chanwoo Choi
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.drivers/extcon/Kconfig +1
-0@@ -54,6 +54,7 @@ config EXTCON_MAX14577 config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TEST
If it won't compile w/o gpiolib, what's the use of COMIPLE_TEST?
And no, it shouldn't depend on gpiolib. It has empty stubs for the case ofCONFIG_GPIOLIB=n. Obviously something is wrong with the GPIO headers, I'll look into it.
[...]
Quoted 2 lines
drivers/extcon/Kconfig +0
-0Thanks,Chanwoo Choi
MBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Chanwoo Choi
maintainerHi,
Quoted 13 lines · Sergei Shtylyov
Hello.
Quoted 9 lines · Chanwoo Choi
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.drivers/extcon/Kconfig +0
-0@@ -54,6 +54,7 @@ config EXTCON_MAX14577
Quoted 6 lines
drivers/extcon/Kconfig config EXTCON_MAX14577 · line 57
Quoted 3 lines
drivers/extcon/Kconfig +1
-0config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TESTIf it won't compile w/o gpiolib, what's the use of
COMIPLE_TEST?
And no, it shouldn't depend on gpiolib. It has empty stubs for the case ofCONFIG_GPIOLIB=n. Obviously something is wrong with the GPIO headers, I'll look into it.
Yes. When GPIOLIB is disabled, the build issue don't happen. because include/linux/gpio/consumer.h implement the dummy function for all gpio functions if CONFIG_GPIOLIB is disabled.
For correct operation of max3355, you should add the dependency to the extcon-max3355.c driver. This driver use the GPIO library certainly.
COMPILE_TEST is used for just build test. You can see the detailed data[1].
[1] https://lkml.org/lkml/2013/5/22/155
Thanks,
Chanwoo Choi
Hello.
Quoted 9 lines · Chanwoo Choi
Quoted 9 lines
Quoted 9 lines
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.drivers/extcon/Kconfig +0
-0@@ -54,6 +54,7 @@ config EXTCON_MAX14577
Quoted 8 lines
Quoted 6 lines
drivers/extcon/Kconfig config EXTCON_MAX14577 · line 57
Quoted 3 lines
drivers/extcon/Kconfig +1
-0config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TESTIf it won't compile w/o gpiolib, what's the use of
COMIPLE_TEST?
And no, it shouldn't depend on gpiolib. It has empty stubs for the case ofCONFIG_GPIOLIB=n. Obviously something is wrong with the GPIO headers, I'll look into it.Yes. When GPIOLIB is disabled, the build issue don't happen.
What? It surely does happen!
Quoted 2 lines
because
include/linux/gpio/consumer.himplement the dummy function for all gpio functions ifCONFIG_GPIOLIBis disabled.
Linus W. advised to #include this header explicitly -- I'll try and post.
Quoted 3 lines
For correct operation of max3355, you should add the dependency to the
extcon-max3355.cdriver. This driver use the GPIO library certainly.
I disagree. The driver will just cease to load in this case. I don't see
why we need such dependency. Only compilation time dependencies should be specified, I think.
Quoted 2 lines
COMPILE_TESTis used for just build test. You can see the detailed data[1].
[1] https://lkml.org/lkml/2013/5/22/155
I know. Re-read my question please.
Quoted 2 lines
Thanks,
Chanwoo Choi
MBR, Sergei
Hello.
Quoted 18 lines · Sergei Shtylyov
Quoted 18 lines
Quoted 17 lines
drivers/extcon/Kconfig config EXTCON_MAX14577 · line 57
Quoted 12 lines
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.drivers/extcon/Kconfig +1
-0@@ -54,6 +54,7 @@ config EXTCON_MAX14577 config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TESTIf it won't compile w/o gpiolib, what's the use of
COMIPLE_TEST? And no, it shouldn't depend on gpiolib. It has empty stubs for the case
ofCONFIG_GPIOLIB=n. Obviously something is wrong with the GPIO headers, I'll look into it.
Quoted 8 lines
Quoted 1 line
Yes. When GPIOLIB is disabled, the build issue don't happen.
What? It surely does happen!
Quoted 2 lines
because
include/linux/gpio/consumer.himplement the dummy function for all gpio functions ifCONFIG_GPIOLIBis disabled.Linus W. advised to #include this header explicitly -- I'll try and post.
I see you already #include'd it, thanks. But in that case, <linux/gpio.h>
doesn't seem necessary.
Quoted 2 lines
Quoted 2 lines
Thanks,
Chanwoo Choi
MBR, Sergei
Chanwoo Choi
maintainerQuoted 20 lines · Sergei Shtylyov
Hello.
Quoted 16 lines · Chanwoo Choi
Quoted 15 lines
drivers/extcon/Kconfig config EXTCON_MAX14577 · line 57
Quoted 12 lines
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.drivers/extcon/Kconfig +1
-0@@ -54,6 +54,7 @@ config EXTCON_MAX14577 config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TESTIf it won't compile w/o gpiolib, what's the use of
COMIPLE_TEST?
And no, it shouldn't depend on gpiolib. It has empty stubs for the case ofCONFIG_GPIOLIB=n. Obviously something is wrong with the GPIO headers, I'll look into it.
Quoted 3 lines
Quoted 1 line
Yes. When GPIOLIB is disabled, the build issue don't happen.
What? It surely does happen!
hmm....
Sure. you need to check the include/linux/gpio/consumer.h.
Because of build error happen, you miss to include the "linux/gpio/consumer.h" header file in extcon-max3355.c. Please test it for enough time.
Quoted 5 lines
Quoted 3 lines
because
include/linux/gpio/consumer.himplement the dummy function for all gpio functions ifCONFIG_GPIOLIBis disabled.Linus W. advised to #include this header explicitly -- I'll try and post.
Don't necessary. I already updated it including the "include/linux/gpio/consumer.h".
Quoted 7 lines
Quoted 4 lines
For correct operation of max3355, you should add the dependency to the
extcon-max3355.cdriver. This driver use the GPIO library certainly.I disagree. The driver will just cease to load in this case. I don't see why we need such dependency. Only compilation time dependencies should be
specified, I think.
This driver have to depend on GPIOLIB.
Why are you disagreeing the COMPILE_TEST dependency? It is just compile test without anything.
Hello.
Quoted 18 lines · Chanwoo Choi
Quoted 18 lines
Quoted 17 lines
Quoted 9 lines
Quoted 9 lines
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.drivers/extcon/Kconfig +0
-0@@ -54,6 +54,7 @@ config EXTCON_MAX14577Quoted 6 lines
drivers/extcon/Kconfig config EXTCON_MAX14577 · line 57
Quoted 3 lines
drivers/extcon/Kconfig +1
-0config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TESTIf it won't compile w/o gpiolib, what's the use of
COMIPLE_TEST?
And no, it shouldn't depend on gpiolib. It has empty stubs for the case ofCONFIG_GPIOLIB=n. Obviously something is wrong with the GPIO headers, I'll look into it.Yes. When GPIOLIB is disabled, the build issue don't happen.
Quoted 7 lines
Quoted 1 line
What? It surely does happen!
hmm....
Sure. you need to check theinclude/linux/gpio/consumer.h.Because of build error happen, you miss to include the "
linux/gpio/consumer.h" header file inextcon-max3355.c. Please test it for enough time.
Yes, with this file #include'd, it build fine now.
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
because
include/linux/gpio/consumer.himplement the dummy function for all gpio functions ifCONFIG_GPIOLIBis disabled.Linus W. advised to #include this header explicitly -- I'll try and post.
Don't necessary. I already updated it including the "
include/linux/gpio/consumer.h".
I saw that, yes.
Quoted 10 lines
Quoted 6 lines
Quoted 3 lines
For correct operation of max3355, you should add the dependency to the
extcon-max3355.cdriver. This driver use the GPIO library certainly.I disagree. The driver will just cease to load in this case. I don't see why we need such dependency. Only compilation time dependencies should be
specified, I think.This driver have to depend on GPIOLIB.
Why are you disagreeing theCOMPILE_TESTdependency? It is just compile test without anything.
I agree now. I still disagree about the gpiolib dependency though.
MBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Chanwoo Choi
maintainerQuoted 45 lines · Sergei Shtylyov
Hello.
Quoted 18 lines · Chanwoo Choi
Quoted 18 lines
Quoted 17 lines
Quoted 9 lines
Quoted 9 lines
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.drivers/extcon/Kconfig +0
-0@@ -54,6 +54,7 @@ config EXTCON_MAX14577Quoted 6 lines
drivers/extcon/Kconfig config EXTCON_MAX14577 · line 57
Quoted 3 lines
drivers/extcon/Kconfig +1
-0config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TESTIf it won't compile w/o gpiolib, what's the use of
COMIPLE_TEST?
And no, it shouldn't depend on gpiolib. It has empty stubs for the case ofCONFIG_GPIOLIB=n. Obviously something is wrong with the GPIO headers, I'll look into it.Yes. When GPIOLIB is disabled, the build issue don't happen.
Quoted 7 lines
Quoted 1 line
What? It surely does happen!
hmm....
Sure. you need to check theinclude/linux/gpio/consumer.h.Because of build error happen, you miss to include the "
linux/gpio/consumer.h" header file inextcon-max3355.c. Please test it for enough time.Yes, with this file #include'd, it build fine now.
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
because
include/linux/gpio/consumer.himplement the dummy function for all gpio functions ifCONFIG_GPIOLIBis disabled.Linus W. advised to #include this header explicitly -- I'll try and post.
Don't necessary. I already updated it including the "
include/linux/gpio/consumer.h".I saw that, yes.
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines
For correct operation of max3355, you should add the dependency to the
extcon-max3355.cdriver. This driver use the GPIO library certainly.
Quoted 8 lines
Quoted 6 lines
Quoted 2 lines
I disagree. The driver will just cease to load in this case. I don't see why we need such dependency. Only compilation time dependencies should be
specified, I think.This driver have to depend on GPIOLIB.
Why are you disagreeing theCOMPILE_TESTdependency? It is just compile test without anything.I agree now. I still disagree about the gpiolib dependency though.
If gpiolib is disabled, extcon-max3355.c might not operate it correctly. Just this driver could be built without operation because gpiolib function will not do the any behavior.
I think that it is not too much problem. I should send the pull request within this week. If you want to need more discussion of extcon-max3355.c,
I will not include it on pull request for v4.5 because there is issue.
Hello.
Quoted 44 lines · Chanwoo Choi
Quoted 44 lines
Quoted 18 lines
Quoted 18 lines
Quoted 17 lines
Quoted 9 lines
Quoted 9 lines
This patch depend on GPIOLIB configuration as following:
I modified it with following diff and applied it.drivers/extcon/Kconfig +0
-0@@ -54,6 +54,7 @@ config EXTCON_MAX14577Quoted 6 lines
drivers/extcon/Kconfig config EXTCON_MAX14577 · line 57
Quoted 3 lines
drivers/extcon/Kconfig +1
-0config EXTCON_MAX3355 tristate "Maxim MAX3355 USB OTG EXTCON Support" + depends on GPIOLIB || COMPILE_TESTIf it won't compile w/o gpiolib, what's the use of
COMIPLE_TEST?
And no, it shouldn't depend on gpiolib. It has empty stubs for the case ofCONFIG_GPIOLIB=n. Obviously something is wrong with the GPIO headers, I'll look into it.Yes. When GPIOLIB is disabled, the build issue don't happen.
Quoted 7 lines
Quoted 1 line
What? It surely does happen!
hmm....
Sure. you need to check theinclude/linux/gpio/consumer.h.Because of build error happen, you miss to include the "
linux/gpio/consumer.h" header file inextcon-max3355.c. Please test it for enough time.Yes, with this file #include'd, it build fine now.
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
because
include/linux/gpio/consumer.himplement the dummy function for all gpio functions ifCONFIG_GPIOLIBis disabled.Linus W. advised to #include this header explicitly -- I'll try and post.
Don't necessary. I already updated it including the "
include/linux/gpio/consumer.h".I saw that, yes.
Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
For correct operation of max3355, you should add the dependency to the
extcon-max3355.cdriver. This driver use the GPIO library certainly.I disagree. The driver will just cease to load in this case. I don't see why we need such dependency. Only compilation time dependencies should be
specified, I think.
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
This driver have to depend on GPIOLIB.
Why are you disagreeing theCOMPILE_TESTdependency? It is just compile test without anything.I agree now. I still disagree about the gpiolib dependency though.
If gpiolib is disabled,
extcon-max3355.cmight not operate it correctly.
It'll just fail the probe, that's all.
Quoted 2 lines
Just this driver could be built without operation because gpiolib function will not do the any behavior.
devm_gpiod_get() will just fail with -ENOSYS.
Quoted 3 lines
I think that it is not too much problem. I should send the pull request within this week. If you want to need more discussion of
extcon-max3355.c,
I will not include it on pull request for v4.5 because there is issue.
No, please include it into the pull request.
MBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html