PCI: designware: split samsung and fsl bindings
Subsystems (5)
PATCH v3 1/3 PCI: designware: split samsung and fsl bindings
The glue around the core designware IP is
significantly different between the Exynos and
i.MX, which is reflected in the DT bindings.
Note that this patch doesn't change any bindings, but just alters the documentation to match reality of deployed DTs and kernels.
--- .../devicetree/bindings/pci/designware-pcie.txt | 69 +-------------------- .../devicetree/bindings/pci/fsl,imx6q-pcie.txt | 38 ++++++++++++ .../bindings/pci/samsung,exynos5440-pcie.txt | 70 ++++++++++++++++++++++ 3 files changed, 109 insertions(+), 68 deletions(-) create mode 100644 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt create mode 100644 Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt
Documentation/devicetree/bindings/pci/designware-pcie.txt +1 -68
@@ -1,15 +1,7 @@ * Synopsys Designware PCIe interface Required properties: -- compatible: should contain "snps,dw-pcie" to identify the - core, plus an identifier for the specific instance, such - as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie". -- reg: base addresses and lengths of the pcie controller, - the phy controller, additional register for the phy controller. -- interrupts: interrupt values for level interrupt, - pulse interrupt, special interrupt. -- clocks: from common clock binding: handle to pci clock. -- clock-names: from common clock binding: should be "pcie" and "pcie_bus". +- compatible: should contain "snps,dw-pcie" to identify the core. - #address-cells: set to <3> - #size-cells: set to <2> - device_type: set to "pci"
@@ -22,62 +14,3 @@ Required properties: Optional properties: - reset-gpio: gpio pin number of power good signal - -Optional properties for fsl,imx6q-pcie -- power-on-gpio: gpio pin number of power-enable signal -- wake-up-gpio: gpio pin number of incoming wakeup signal -- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal - -Example: - -SoC specific DT Entry: - - pcie at 290000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x290000 0x1000 - 0x270000 0x1000 - 0x271000 0x40>; - interrupts = <0 20 0>, <0 21 0>, <0 22 0>; - clocks = <&clock 28>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0x0 0 &gic 53>; - num-lanes = <4>; - }; - - pcie at 2a0000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x2a0000 0x1000 - 0x272000 0x1000 - 0x271040 0x40>; - interrupts = <0 23 0>, <0 24 0>, <0 25 0>; - clocks = <&clock 29>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0x0 0 &gic 56>; - num-lanes = <4>; - }; - -Board specific DT Entry: - - pcie at 290000 { - reset-gpio = <&pin_ctrl 5 0>; - }; - - pcie at 2a0000 { - reset-gpio = <&pin_ctrl 22 0>; - };
Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt new file +38 -0
@@ -0,0 +1,38 @@ +* Freescale i.MX6 PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "fsl,imx6q-pcie" +- reg: base addresse and length of the pcie controller +- interrupts: Must contain interrupt handle for controller INTA output. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "pcie_ref_125m" + - "sata_ref_100m" + - "lvds_gate" + - "pcie_axi" + +Optional properties: +- power-on-gpio: gpio pin number of power-enable signal +- wake-up-gpio: gpio pin number of incoming wakeup signal +- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal + +Example: + + pcie at 0x01000000 { + compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; + reg = <0x01ffc000 0x4000>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 + 0x81000000 0 0 0x01f80000 0 0x00010000 + 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; + num-lanes = <1>; + interrupts = <0 123 0x04>; + clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>; + clock-names = "pcie_ref_125m", "sata_ref_100m", "lvds_gate", "pcie_axi"; + };
Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt new file +70 -0
70 lines not on this page · raw message
Signature · 1 line
1.8.5.3
PATCH v3 2/3 ARM: dts: imx6: extend PCIe interrupt list for MSI
Add optional irqs, necessary for MSI handling.
--- Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt | 10 +++++++++- arch/arm/boot/dts/imx6qdl.dtsi | 3 ++- 2 files changed, 11 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +9 -1
@@ -16,6 +16,13 @@ Required properties: - "pcie_axi" Optional properties: +- interrupts: Must contain an entry for each entry in the + interrupt-names property. +- interrupt-names: May include the following entries: + - "inta" + - "intb" + - "intc" + - "intd/msi" if not present the driver won't be able to handle MSI - power-on-gpio: gpio pin number of power-enable signal - wake-up-gpio: gpio pin number of incoming wakeup signal - disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal
@@ -32,7 +39,8 @@ Example: 0x81000000 0 0 0x01f80000 0 0x00010000 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; num-lanes = <1>; - interrupts = <0 123 0x04>; + interrupt-names = "inta", "intb", "intc", "intd/msi"; + interrupts = <0 123 0x04>, <0 122 0x04>, <0 121 0x04>, <0 120 0x04>; clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>; clock-names = "pcie_ref_125m", "sata_ref_100m", "lvds_gate", "pcie_axi"; };
arch/arm/boot/dts/imx6qdl.dtsi +2 -1
@@ -126,7 +126,8 @@ 0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */ 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */ num-lanes = <1>; - interrupts = <0 123 0x04>; + interrupt-names = "inta", "intb", "intc", "intd/msi"; + interrupts = <0 123 0x04>, <0 122 0x04>, <0 121 0x04>, <0 120 0x04>; clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>; clock-names = "pcie_ref_125m", "sata_ref_100m", "lvds_gate", "pcie_axi"; status = "disabled";
Signature · 1 line
1.8.5.3
PATCH v3 2/3 ARM: dts: imx6: extend PCIe interrupt list for MSI
Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt Example: · line 44
Quoted 6 lines · On Thursday 27 February 2014 17:41:44 Lucas Stach wrote:
num-lanes = <1>;Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +2
-1- interrupts = <0 123 0x04>; + interrupt-names = "inta", "intb", "intc", "intd/msi"; + interrupts = <0 123 0x04>, <0 122 0x04>, <0 121 0x04>, <0 120 0x04>; clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>;
The standard PCI interrupts should not be listed here, you need to put them into the "interrupt-map" property so the of_irq_parse_and_map_pci() function can translate them.
Arnd
PATCH v3 2/3 ARM: dts: imx6: extend PCIe interrupt list for MSI
Hi Arnd,
Am Donnerstag, den 27.02.2014, 17:44 +0100 schrieb Arnd Bergmann:
Quoted 8 lines · On Thursday 27 February 2014 17:41:44 Lucas Stach wrote:
Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt Example: · line 44
Quoted 6 lines
num-lanes = <1>;Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +2
-1- interrupts = <0 123 0x04>; + interrupt-names = "inta", "intb", "intc", "intd/msi"; + interrupts = <0 123 0x04>, <0 122 0x04>, <0 121 0x04>, <0 120 0x04>; clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>;
Quoted 5 lines
The standard PCI interrupts should not be listed here, you need to put them into the "interrupt-map" property so the
of_irq_parse_and_map_pci()function can translate them.Arnd
So as INTA is already listed and implemented in the driver this way, this means the binding is totally bogus (taking into account that it didn't match the documented designware binding in more places).
I wonder if we should just break the binding to sort things out, given that there are not that many users of imx-pcie yet.
Regards,
Lucas
Signature · 4 lines
Pengutronix e.K. | Lucas Stach | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-5076 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
PATCH v3 2/3 ARM: dts: imx6: extend PCIe interrupt list for MSI
Quoted 14 lines · On Friday 28 February 2014 11:19:36 Lucas Stach wrote:
Am Donnerstag, den 27.02.2014, 17:44 +0100 schrieb Arnd Bergmann:
Quoted 8 lines · On Thursday 27 February 2014 17:41:44 Lucas Stach wrote:
Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt Example: · line 44
Quoted 6 lines
num-lanes = <1>;Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +2
-1- interrupts = <0 123 0x04>; + interrupt-names = "inta", "intb", "intc", "intd/msi"; + interrupts = <0 123 0x04>, <0 122 0x04>, <0 121 0x04>, <0 120 0x04>; clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>;Quoted 4 lines
The standard PCI interrupts should not be listed here, you need to put them into the "interrupt-map" property so the
of_irq_parse_and_map_pci()function can translate them.
Quoted 6 lines
So as INTA is already listed and implemented in the driver this way, this means the binding is totally bogus (taking into account that it didn't match the documented designware binding in more places).
I wonder if we should just break the binding to sort things out, given that there are not that many users of imx-pcie yet.
That may be best, yes. If we have to provide backwards compatibility, the driver can have a fallback for the case where no interrupt-map property is present, but it should not try to handle multiple interrupt lines that way, only the trivial case where you have a single IntA line for all devices.
Arnd
PATCH v3 3/3 PCI: imx6: add support for MSI
In reply to Lucas StachThis patch adds support for Message Signaled Interrupt in the imx6q-pcie driver. It is done in a similar way as for the Exynos PCIe driver (commit f342d940ee0e3a2b5197fd4fbade1cb6bbc960b7), which is also using the Synopsys designware PCIe IP core.
--- drivers/pci/host/pci-imx6.c | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
drivers/pci/host/pci-imx6.c +30 -0
@@ -25,6 +25,7 @@#include <linux/resource.h> #include <linux/signal.h> #include <linux/types.h> +#include <linux/interrupt.h> #include "pcie-designware.h"
@@ -329,6 +330,17 @@ static int imx6_pcie_wait_for_link(struct pcie_port *pp)return 0 ; } +/* legacy IRQD/MSI interrupt */ +static irqreturn_t imx6_pcie_irqd_msi_handler (int irq,void *arg) +{ +struct pcie_port *pp = arg; + +if (IS_ENABLED (CONFIG_PCI_MSI )) +dw_handle_msi_irq (pp); + +return IRQ_HANDLED ; +} +static int imx6_pcie_start_link (struct pcie_port *pp) {struct imx6_pcie *imx6_pcie =to_imx6_pcie (pp);
@@ -403,6 +415,9 @@ static void imx6_pcie_host_init(struct pcie_port *pp)dw_pcie_setup_rc (pp);imx6_pcie_start_link (pp); + +if (IS_ENABLED (CONFIG_PCI_MSI ) && (pp->msi_irq >=0 )) +dw_pcie_msi_init (pp); }static void imx6_pcie_reset_phy (struct pcie_port *pp)
@@ -498,6 +513,21 @@ static int imx6_add_pcie_port(struct pcie_port *pp,return -ENODEV ; } +if (IS_ENABLED (CONFIG_PCI_MSI )) { + pp->msi_irq =platform_get_irq_byname (pdev,"intd/msi" ); +if (pp->msi_irq <0 ) { +dev_info (&pdev->dev,"failed to get INTD/MSI, PCIe will not support MSI\n" ); + }else { + ret =devm_request_irq (&pdev->dev, pp->msi_irq, + imx6_pcie_irqd_msi_handler, +IRQF_SHARED ,"mx6-pcie-msi" , pp); +if (ret) { +dev_err (&pdev->dev,"failed to request INTD/MSI irq\n" ); +return -ENODEV ; + } + } + } + pp->root_bus_nr =-1 ; pp->ops = &imx6_pcie_host_ops;
Signature · 1 line
1.8.5.3