Skip to contentSkip to conversation

Document more PTP timestamping known quirks

PATCH In review Vladimir Oltean 4 participants 26 messages Jul 17, 2020 – Jul 25, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover Document more PTP timestamping known quirks

I've tried to collect and summarize the conclusions of these discussions:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
which were a bit surprising to me. Make sure they are present in the documentation.

Vladimir Oltean (3):
docs: networking: timestamping: rename last section to "Known bugs".
docs: networking: timestamping: add one more known issue
docs: networking: timestamping: add a set of frequently asked
questions

 Documentation/networking/timestamping.rst | 77 ++++++++++++++++++++---
 1 file changed, 70 insertions(+), 7 deletions(-)
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/3 docs: networking: timestamping: rename last section to "Known bugs".

One more quirk of the timestamping infrastructure will be documented shortly. Rename the section from "Other caveats for MAC drivers" to simply "Known bugs". This uncovers some bad phrasing at the beginning of the section, which is now corrected.

---
 Documentation/networking/timestamping.rst | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)
Documentation/networking/timestamping.rst +8 -8
index 5fa4e2274dd9..9a1f4cb4ce9e 100644
@@ -711,14 +711,14 @@ discoverable and attachable to a ``struct phy_device`` through Device Tree, and
 for the rest, they use the same mii_ts infrastructure as those. See
 Documentation/devicetree/bindings/ptp/timestamper.txt for more details.
 
-3.2.4 Other caveats for MAC drivers
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
-Stacked PHCs, especially DSA (but not only) - since that doesn't require any
-modification to MAC drivers, so it is more difficult to ensure correctness of
-all possible code paths - is that they uncover bugs which were impossible to
-trigger before the existence of stacked PTP clocks.  One example has to do with
-this line of code, already presented earlier::
+3.2.4 Known bugs
+^^^^^^^^^^^^^^^^
+
+One caveat with stacked PHCs, especially DSA (but not only) - since that
+doesn't require any modification to MAC drivers, so it is more difficult to
+ensure correctness of all possible code paths - is that they uncover bugs which
+were impossible to trigger before the existence of stacked PTP clocks.
+One example has to do with this line of code, already presented earlier::
 
       skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
 
Signature · 1 line
2.25.1
#2 lore raw

Re: [PATCH net-next 1/3] docs: networking: timestamping: rename last section to "Known bugs".

Quoted 25 lines · Vladimir Oltean

One more quirk of the timestamping infrastructure will be documented shortly. Rename the section from "Other caveats for MAC drivers" to simply "Known bugs". This uncovers some bad phrasing at the beginning of the section, which is now corrected.

---
 Documentation/networking/timestamping.rst | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)
Documentation/networking/timestamping.rst +0 -7
index 5fa4e2274dd9..9a1f4cb4ce9e 100644
@@ -711,14 +711,14 @@ discoverable and attachable to a ``struct phy_device`` through Device Tree, and
 for the rest, they use the same mii_ts infrastructure as those. See
 Documentation/devicetree/bindings/ptp/timestamper.txt for more details.
 
-3.2.4 Other caveats for MAC drivers
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
-Stacked PHCs, especially DSA (but not only) - since that doesn't require any
-modification to MAC drivers, so it is more difficult to ensure correctness of
-all possible code paths - is that they uncover bugs which were impossible to
-trigger before the existence of stacked PTP clocks.  One example has to do with

Documentation/networking/timestamping.rst discoverable and attachable to a ``struct phy_device`` through Device Tree, and · line 722

Quoted 10 lines
Documentation/networking/timestamping.rst +8 -1
-this line of code, already presented earlier::
+3.2.4 Known bugs
+^^^^^^^^^^^^^^^^
+
+One caveat with stacked PHCs, especially DSA (but not only) - since that
+doesn't require any modification to MAC drivers, so it is more difficult to
+ensure correctness of all possible code paths - is that they uncover bugs which
+were impossible to trigger before the existence of stacked PTP clocks.
+One example has to do with this line of code, already presented earlier::
 

The interjection between - - is really long and made it difficult to parse this statement. Maybe re-word it like

One caveat with stacked PHCs is that they uncover bugs which were impossible to trigger otherwise, as it is more difficult to ensure correctness of all possible code flows. This is especially true of DSA since it does not require any modifications to the MAC drivers to setup. One example has to do with this line of code, already presented earlier::

Quoted 3 lines
Documentation/networking/timestamping.rst +0 -0
       skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
 
#3 lore raw

PATCH 2/3 docs: networking: timestamping: add one more known issue

In reply to Vladimir Oltean

Document the fact that Ethernet PHY timestamping has a fundamentally flawed corner case (which in fact hits the majority of networking drivers): a PHY for which its host MAC driver doesn't forward the phy_mii_ioctl for timestamping is still going to be presented to user space as functional.

Fixing this inconsistency would require moving the phy_has_tsinfo() check inside all MAC drivers which are capable of PHY timestamping, to be in harmony with the existing design for phy_has_hwtstamp() checks. Instead of doing that, document the preferable solution which is that offending MAC drivers be fixed instead.

---
 Documentation/networking/timestamping.rst | 37 +++++++++++++++++++++++
 1 file changed, 37 insertions(+)
Documentation/networking/timestamping.rst +37 -0
index 9a1f4cb4ce9e..4004c5d2771d 100644
@@ -754,3 +754,40 @@ check in their "TX confirmation" portion, not only for
 that PTP timestamping is not enabled for anything other than the outermost PHC,
 this enhanced check will avoid delivering a duplicated TX timestamp to user
 space.
+
+Another known limitation is the design of the ``__ethtool_get_ts_info``
+function::
+
+  int __ethtool_get_ts_info(struct net_device *dev, struct ethtool_ts_info *info)
+  {
+          const struct ethtool_ops *ops = dev->ethtool_ops;
+          struct phy_device *phydev = dev->phydev;
+
+          memset(info, 0, sizeof(*info));
+          info->cmd = ETHTOOL_GET_TS_INFO;
+
+          if (phy_has_tsinfo(phydev))
+                  return phy_ts_info(phydev, info);
+          if (ops->get_ts_info)
+                  return ops->get_ts_info(dev, info);
+
+          info->so_timestamping = SOF_TIMESTAMPING_RX_SOFTWARE |
+                                  SOF_TIMESTAMPING_SOFTWARE;
+          info->phc_index = -1;
+
+          return 0;
+  }
+
+Because the generic function searches first for the timestamping capabilities
+of the attached PHY, and returns them directly without consulting the MAC
+driver, no checking is being done whether the requirements described in `3.2.2
+Ethernet PHYs`_ are implemented or not. Therefore, if the MAC driver does not
+satisfy the requirements for PHY timestamping, and
+``CONFIG_NETWORK_PHY_TIMESTAMPING`` is enabled, then a non-functional PHC index
+(the one corresponding to the PHY) will be reported to user space, via
+``ethtool -T``.
+
+The correct solution to this problem is to implement the PHY timestamping
+requirements in the MAC driver found broken, and submit as a bug fix patch to
[email protected]. See :ref:`Documentation/process/stable-kernel-rules.rst
+<stable_kernel_rules>` for more details.
Signature · 1 line
2.25.1
#4 lore raw

Re: [PATCH net-next 2/3] docs: networking: timestamping: add one more known issue

Quoted 11 lines · Vladimir Oltean

Document the fact that Ethernet PHY timestamping has a fundamentally flawed corner case (which in fact hits the majority of networking drivers): a PHY for which its host MAC driver doesn't forward the phy_mii_ioctl for timestamping is still going to be presented to user space as functional.

Fixing this inconsistency would require moving the phy_has_tsinfo() check inside all MAC drivers which are capable of PHY timestamping, to be in harmony with the existing design for phy_has_hwtstamp() checks. Instead of doing that, document the preferable solution which is that offending MAC drivers be fixed instead.

This statement feels weird. Aren't you documenting that the preferable solution is? I.e. "Document this preferable solution: Fix the offending MAC driver"

Or am I misunderstanding what the issue is here?

Quoted 52 lines
---
 Documentation/networking/timestamping.rst | 37 +++++++++++++++++++++++
 1 file changed, 37 insertions(+)
Documentation/networking/timestamping.rst +37 -0
index 9a1f4cb4ce9e..4004c5d2771d 100644
@@ -754,3 +754,40 @@ check in their "TX confirmation" portion, not only for
 that PTP timestamping is not enabled for anything other than the outermost PHC,
 this enhanced check will avoid delivering a duplicated TX timestamp to user
 space.
+
+Another known limitation is the design of the ``__ethtool_get_ts_info``
+function::
+
+  int __ethtool_get_ts_info(struct net_device *dev, struct ethtool_ts_info *info)
+  {
+          const struct ethtool_ops *ops = dev->ethtool_ops;
+          struct phy_device *phydev = dev->phydev;
+
+          memset(info, 0, sizeof(*info));
+          info->cmd = ETHTOOL_GET_TS_INFO;
+
+          if (phy_has_tsinfo(phydev))
+                  return phy_ts_info(phydev, info);
+          if (ops->get_ts_info)
+                  return ops->get_ts_info(dev, info);
+
+          info->so_timestamping = SOF_TIMESTAMPING_RX_SOFTWARE |
+                                  SOF_TIMESTAMPING_SOFTWARE;
+          info->phc_index = -1;
+
+          return 0;
+  }
+
+Because the generic function searches first for the timestamping capabilities
+of the attached PHY, and returns them directly without consulting the MAC
+driver, no checking is being done whether the requirements described in `3.2.2
+Ethernet PHYs`_ are implemented or not. Therefore, if the MAC driver does not
+satisfy the requirements for PHY timestamping, and
+``CONFIG_NETWORK_PHY_TIMESTAMPING`` is enabled, then a non-functional PHC index
+(the one corresponding to the PHY) will be reported to user space, via
+``ethtool -T``.
+
+The correct solution to this problem is to implement the PHY timestamping
+requirements in the MAC driver found broken, and submit as a bug fix patch to
[email protected]. See :ref:`Documentation/process/stable-kernel-rules.rst
+<stable_kernel_rules>` for more details.
#5 lore raw

Re: [PATCH net-next 2/3] docs: networking: timestamping: add one more known issue

Quoted 15 lines · Jacob Keller
Quoted 11 lines · Vladimir Oltean

Document the fact that Ethernet PHY timestamping has a fundamentally flawed corner case (which in fact hits the majority of networking drivers): a PHY for which its host MAC driver doesn't forward the phy_mii_ioctl for timestamping is still going to be presented to user space as functional.

Fixing this inconsistency would require moving the phy_has_tsinfo() check inside all MAC drivers which are capable of PHY timestamping, to be in harmony with the existing design for phy_has_hwtstamp() checks. Instead of doing that, document the preferable solution which is that offending MAC drivers be fixed instead.

Quoted 6 lines

This statement feels weird. Aren't you documenting that the preferable solution is? I.e. "Document this preferable solution: Fix the offending MAC driver"

Or am I misunderstanding what the issue is here?

You're right, it looks like I wasn't thinking in full sentences at that particular time of day.

Quoted 44 lines
Quoted 44 lines
---
 Documentation/networking/timestamping.rst | 37 +++++++++++++++++++++++
 1 file changed, 37 insertions(+)
Documentation/networking/timestamping.rst +30 -0
index 9a1f4cb4ce9e..4004c5d2771d 100644
@@ -754,3 +754,40 @@ check in their "TX confirmation" portion, not only for
 that PTP timestamping is not enabled for anything other than the outermost PHC,
 this enhanced check will avoid delivering a duplicated TX timestamp to user
 space.
+
+Another known limitation is the design of the ``__ethtool_get_ts_info``
+function::
+
+  int __ethtool_get_ts_info(struct net_device *dev, struct ethtool_ts_info *info)
+  {
+          const struct ethtool_ops *ops = dev->ethtool_ops;
+          struct phy_device *phydev = dev->phydev;
+
+          memset(info, 0, sizeof(*info));
+          info->cmd = ETHTOOL_GET_TS_INFO;
+
+          if (phy_has_tsinfo(phydev))
+                  return phy_ts_info(phydev, info);
+          if (ops->get_ts_info)
+                  return ops->get_ts_info(dev, info);
+
+          info->so_timestamping = SOF_TIMESTAMPING_RX_SOFTWARE |
+                                  SOF_TIMESTAMPING_SOFTWARE;
+          info->phc_index = -1;
+
+          return 0;
+  }
+
+Because the generic function searches first for the timestamping capabilities
+of the attached PHY, and returns them directly without consulting the MAC
+driver, no checking is being done whether the requirements described in `3.2.2
+Ethernet PHYs`_ are implemented or not. Therefore, if the MAC driver does not
+satisfy the requirements for PHY timestamping, and
+``CONFIG_NETWORK_PHY_TIMESTAMPING`` is enabled, then a non-functional PHC index
Quoted 8 lines

Documentation/networking/timestamping.rst check in their "TX confirmation" portion, not only for · line 793

Quoted 8 lines
Documentation/networking/timestamping.rst +7 -0
+(the one corresponding to the PHY) will be reported to user space, via
+``ethtool -T``.
+
+The correct solution to this problem is to implement the PHY timestamping
+requirements in the MAC driver found broken, and submit as a bug fix patch to
[email protected]. See :ref:`Documentation/process/stable-kernel-rules.rst
+<stable_kernel_rules>` for more details.

Thanks,
-Vladimir

#6 lore raw

PATCH 3/3 docs: networking: timestamping: add a set of frequently asked questions

In reply to Vladimir Oltean

These are some questions I had while trying to explain the behavior of some drivers with respect to software timestamping. Answered with the help of Richard Cochran.

---
 Documentation/networking/timestamping.rst | 26 +++++++++++++++++++++++
 1 file changed, 26 insertions(+)
Documentation/networking/timestamping.rst +26 -0
index 4004c5d2771d..e01ec01179fe 100644
@@ -791,3 +791,29 @@ The correct solution to this problem is to implement the PHY timestamping
 requirements in the MAC driver found broken, and submit as a bug fix patch to
 [email protected]. See :ref:`Documentation/process/stable-kernel-rules.rst
 <stable_kernel_rules>` for more details.
+
+3.4 Frequently asked questions
+------------------------------
+
+Q: When should drivers set SKBTX_IN_PROGRESS?
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+When the interface they represent offers both ``SOF_TIMESTAMPING_TX_HARDWARE``
+and ``SOF_TIMESTAMPING_TX_SOFTWARE``.
+Originally, the network stack could deliver either a hardware or a software
+time stamp, but not both. This flag prevents software timestamp delivery.
+This restriction was eventually lifted via the ``SOF_TIMESTAMPING_OPT_TX_SWHW``
+option, but still the original behavior is preserved as the default.
+
+Q: Should drivers that don't offer SOF_TIMESTAMPING_TX_SOFTWARE call skb_tx_timestamp()?
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The ``skb_clone_tx_timestamp()`` function from its body helps with propagation
+of TX timestamps from PTP PHYs, and the required placement of this call is the
+same as for software TX timestamping.
+Additionally, since PTP is broken on ports with timestamping PHYs and unmet
+requirements, the consequence is that any driver which may be ever coupled to
+a timestamping-capable PHY in ``netdev->phydev`` should call at least
+``skb_clone_tx_timestamp()``. However, calling the higher-level
+``skb_tx_timestamp()`` instead achieves the same purpose, but also offers
+additional compliance to ``SOF_TIMESTAMPING_TX_SOFTWARE``.
Signature · 1 line
2.25.1
#7 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 21 lines · Vladimir Oltean

These are some questions I had while trying to explain the behavior of some drivers with respect to software timestamping. Answered with the help of Richard Cochran.

---
 Documentation/networking/timestamping.rst | 26 +++++++++++++++++++++++
 1 file changed, 26 insertions(+)
Documentation/networking/timestamping.rst +4 -0
index 4004c5d2771d..e01ec01179fe 100644
@@ -791,3 +791,29 @@ The correct solution to this problem is to implement the PHY timestamping
 requirements in the MAC driver found broken, and submit as a bug fix patch to
 [email protected]. See :ref:`Documentation/process/stable-kernel-rules.rst
 <stable_kernel_rules>` for more details.
+
+3.4 Frequently asked questions
+------------------------------
+

Documentation/networking/timestamping.rst The correct solution to this problem is to implement the PHY timestamping · line 807

Quoted 10 lines
Documentation/networking/timestamping.rst +10 -0
+Q: When should drivers set SKBTX_IN_PROGRESS?
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+When the interface they represent offers both ``SOF_TIMESTAMPING_TX_HARDWARE``
+and ``SOF_TIMESTAMPING_TX_SOFTWARE``.
+Originally, the network stack could deliver either a hardware or a software
+time stamp, but not both. This flag prevents software timestamp delivery.
+This restriction was eventually lifted via the ``SOF_TIMESTAMPING_OPT_TX_SWHW``
+option, but still the original behavior is preserved as the default.
+

So, this implies that we set this only if both are supported? I thought the intention was to set this flag whenever we start a HW timestamp.

Documentation/networking/timestamping.rst The correct solution to this problem is to implement the PHY timestamping · line 819

Quoted 13 lines
Documentation/networking/timestamping.rst +12 -0
+Q: Should drivers that don't offer SOF_TIMESTAMPING_TX_SOFTWARE call skb_tx_timestamp()?
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The ``skb_clone_tx_timestamp()`` function from its body helps with propagation
+of TX timestamps from PTP PHYs, and the required placement of this call is the
+same as for software TX timestamping.
+Additionally, since PTP is broken on ports with timestamping PHYs and unmet
+requirements, the consequence is that any driver which may be ever coupled to
+a timestamping-capable PHY in ``netdev->phydev`` should call at least
+``skb_clone_tx_timestamp()``. However, calling the higher-level
+``skb_tx_timestamp()`` instead achieves the same purpose, but also offers
+additional compliance to ``SOF_TIMESTAMPING_TX_SOFTWARE``.

This makes sense.

Thanks,
Jake

#8 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 29 lines · Jacob Keller
Quoted 26 lines · Vladimir Oltean

These are some questions I had while trying to explain the behavior of some drivers with respect to software timestamping. Answered with the help of Richard Cochran.

---
 Documentation/networking/timestamping.rst | 26 +++++++++++++++++++++++
 1 file changed, 26 insertions(+)
Documentation/networking/timestamping.rst +9 -0
index 4004c5d2771d..e01ec01179fe 100644
@@ -791,3 +791,29 @@ The correct solution to this problem is to implement the PHY timestamping
 requirements in the MAC driver found broken, and submit as a bug fix patch to
 [email protected]. See :ref:`Documentation/process/stable-kernel-rules.rst
 <stable_kernel_rules>` for more details.
+
+3.4 Frequently asked questions
+------------------------------
+
+Q: When should drivers set SKBTX_IN_PROGRESS?
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+When the interface they represent offers both ``SOF_TIMESTAMPING_TX_HARDWARE``
+and ``SOF_TIMESTAMPING_TX_SOFTWARE``.
Quoted 9 lines

Documentation/networking/timestamping.rst The correct solution to this problem is to implement the PHY timestamping · line 807

Quoted 5 lines
Documentation/networking/timestamping.rst +5 -0
+Originally, the network stack could deliver either a hardware or a software
+time stamp, but not both. This flag prevents software timestamp delivery.
+This restriction was eventually lifted via the ``SOF_TIMESTAMPING_OPT_TX_SWHW``
+option, but still the original behavior is preserved as the default.
+

So, this implies that we set this only if both are supported? I thought the intention was to set this flag whenever we start a HW timestamp.

It's only _required_ when SOF_TIMESTAMPING_TX_SOFTWARE is used, it seems. I had also thought of setting 'SKBTX_IN_PROGRESS' as good practice, but there are many situations where it can do more harm than good.

Quoted 16 lines

Documentation/networking/timestamping.rst The correct solution to this problem is to implement the PHY timestamping · line 819

Quoted 13 lines
Documentation/networking/timestamping.rst +12 -0
+Q: Should drivers that don't offer SOF_TIMESTAMPING_TX_SOFTWARE call skb_tx_timestamp()?
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The ``skb_clone_tx_timestamp()`` function from its body helps with propagation
+of TX timestamps from PTP PHYs, and the required placement of this call is the
+same as for software TX timestamping.
+Additionally, since PTP is broken on ports with timestamping PHYs and unmet
+requirements, the consequence is that any driver which may be ever coupled to
+a timestamping-capable PHY in ``netdev->phydev`` should call at least
+``skb_clone_tx_timestamp()``. However, calling the higher-level
+``skb_tx_timestamp()`` instead achieves the same purpose, but also offers
+additional compliance to ``SOF_TIMESTAMPING_TX_SOFTWARE``.

This makes sense.

Quoted 2 lines

Thanks,
Jake

Thanks,
-Vladimir

#9 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 14 lines · Vladimir Oltean
Quoted 12 lines · Jacob Keller

Documentation/networking/timestamping.rst The correct solution to this problem is to implement the PHY timestamping · line 807

Quoted 7 lines · Vladimir Oltean
Documentation/networking/timestamping.rst +7 -0
+When the interface they represent offers both ``SOF_TIMESTAMPING_TX_HARDWARE``
+and ``SOF_TIMESTAMPING_TX_SOFTWARE``.
+Originally, the network stack could deliver either a hardware or a software
+time stamp, but not both. This flag prevents software timestamp delivery.
+This restriction was eventually lifted via the ``SOF_TIMESTAMPING_OPT_TX_SWHW``
+option, but still the original behavior is preserved as the default.
+

So, this implies that we set this only if both are supported? I thought the intention was to set this flag whenever we start a HW timestamp.

Quoted 5 lines

It's only _required_ when SOF_TIMESTAMPING_TX_SOFTWARE is used, it seems. I had also thought of setting 'SKBTX_IN_PROGRESS' as good practice, but there are many situations where it can do more harm than good.

I guess I've only ever implemented a driver with software timestamping enabled as an option. What sort of issues arise when you have this set? I'm guessing that it's some configuration of stacked devices as in the other cases? If the issue can't be fixed I'd at least like more explanation here, since the prevailing convention is that we set this flag, so understanding when and why it's problematic would be useful.

Thanks,
Jake

#10 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 28 lines · Jacob Keller
Quoted 14 lines · Vladimir Oltean
Quoted 12 lines · Jacob Keller

Documentation/networking/timestamping.rst The correct solution to this problem is to implement the PHY timestamping · line 807

Quoted 7 lines · Vladimir Oltean
Documentation/networking/timestamping.rst +7 -0
+When the interface they represent offers both ``SOF_TIMESTAMPING_TX_HARDWARE``
+and ``SOF_TIMESTAMPING_TX_SOFTWARE``.
+Originally, the network stack could deliver either a hardware or a software
+time stamp, but not both. This flag prevents software timestamp delivery.
+This restriction was eventually lifted via the ``SOF_TIMESTAMPING_OPT_TX_SWHW``
+option, but still the original behavior is preserved as the default.
+

So, this implies that we set this only if both are supported? I thought the intention was to set this flag whenever we start a HW timestamp.

Quoted 5 lines

It's only _required_ when SOF_TIMESTAMPING_TX_SOFTWARE is used, it seems. I had also thought of setting 'SKBTX_IN_PROGRESS' as good practice, but there are many situations where it can do more harm than good.

I guess I've only ever implemented a driver with software timestamping enabled as an option. What sort of issues arise when you have this set? I'm guessing that it's some configuration of stacked devices as in the other cases? If the issue can't be fixed I'd at least like more explanation here, since the prevailing convention is that we set this flag, so understanding when and why it's problematic would be useful.

Quoted 2 lines

Thanks,
Jake

Yes, the problematic cases have to do with stacked PHCs (DSA, PHY). The pattern is that:
- DSA sets SKBTX_IN_PROGRESS
- calls dev_queue_xmit towards the MAC driver
- MAC driver sees SKBTX_IN_PROGRESS, thinks it's the one who set it
- MAC driver delivers TX timestamp
- DSA ends poll or receives TX interrupt, collects its timestamp, and delivers a second TX timestamp
In fact this is explained in a bit more detail in the current timestamping.rst file.
Not only are there existing in-tree drivers that do that (and various subtle variations of it), but new code also has this tendency to take shortcuts and interpret any SKBTX_IN_PROGRESS flag set as being set locally. Good thing it's caught during review most of the time these days. It's an error-prone design.
On the DSA front, 1 driver sets this flag (sja1105) and 3 don't (felix, mv88e6xxx, hellcreek). The driver who had trouble because of this flag? sja1105.
On the PHY front, 2 drivers set this flag (mscc_phy, dp83640) and 1 doesn't (ptp_ines). The driver who had trouble? dp83640.
So it's very far from obvious that setting this flag is 'the prevailing convention'. For a MAC driver, that might well be, but for DSA/PHY, there seem to be risks associated with doing that, and driver writers should know what they're signing up for.

-Vladimir

#11 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 48 lines · Vladimir Oltean
Quoted 28 lines · Jacob Keller
Quoted 14 lines · Vladimir Oltean
Quoted 12 lines · Jacob Keller

Documentation/networking/timestamping.rst The correct solution to this problem is to implement the PHY timestamping · line 807

Quoted 7 lines · Vladimir Oltean
Documentation/networking/timestamping.rst +7 -0
+When the interface they represent offers both ``SOF_TIMESTAMPING_TX_HARDWARE``
+and ``SOF_TIMESTAMPING_TX_SOFTWARE``.
+Originally, the network stack could deliver either a hardware or a software
+time stamp, but not both. This flag prevents software timestamp delivery.
+This restriction was eventually lifted via the ``SOF_TIMESTAMPING_OPT_TX_SWHW``
+option, but still the original behavior is preserved as the default.
+

So, this implies that we set this only if both are supported? I thought the intention was to set this flag whenever we start a HW timestamp.

Quoted 5 lines

It's only _required_ when SOF_TIMESTAMPING_TX_SOFTWARE is used, it seems. I had also thought of setting 'SKBTX_IN_PROGRESS' as good practice, but there are many situations where it can do more harm than good.

I guess I've only ever implemented a driver with software timestamping enabled as an option. What sort of issues arise when you have this set? I'm guessing that it's some configuration of stacked devices as in the other cases? If the issue can't be fixed I'd at least like more explanation here, since the prevailing convention is that we set this flag, so understanding when and why it's problematic would be useful.

Quoted 2 lines

Thanks,
Jake

Yes, the problematic cases have to do with stacked PHCs (DSA, PHY). The pattern is that:
- DSA sets SKBTX_IN_PROGRESS
- calls dev_queue_xmit towards the MAC driver
- MAC driver sees SKBTX_IN_PROGRESS, thinks it's the one who set it
- MAC driver delivers TX timestamp
- DSA ends poll or receives TX interrupt, collects its timestamp, and delivers a second TX timestamp
In fact this is explained in a bit more detail in the current timestamping.rst file.
Not only are there existing in-tree drivers that do that (and various subtle variations of it), but new code also has this tendency to take shortcuts and interpret any SKBTX_IN_PROGRESS flag set as being set locally. Good thing it's caught during review most of the time these days. It's an error-prone design.
On the DSA front, 1 driver sets this flag (sja1105) and 3 don't (felix,

Quoted 9 lines

mv88e6xxx, hellcreek). The driver who had trouble because of this flag? sja1105.
On the PHY front, 2 drivers set this flag (mscc_phy, dp83640) and 1 doesn't (ptp_ines). The driver who had trouble? dp83640.
So it's very far from obvious that setting this flag is 'the prevailing convention'. For a MAC driver, that might well be, but for DSA/PHY, there seem to be risks associated with doing that, and driver writers should know what they're signing up for.

Perhaps the issue is that the MAC driver using SKBTX_IN_PROGRESS as the mechanism for telling if it should deliver a timestamp. Shouldn't they be relying on SKBTX_HW_TSTAMP for the "please timestamp" notification, and then using their own mechanism for forwarding that timestamp once it's complete?

I see a handful of drivers do rely on checking this, but I think that's the real bug here.

Quoted 2 lines

-Vladimir

#12 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 61 lines · Jacob Keller
Quoted 48 lines · Vladimir Oltean
Quoted 28 lines · Jacob Keller
Quoted 14 lines · Vladimir Oltean
Quoted 12 lines · Jacob Keller

Documentation/networking/timestamping.rst The correct solution to this problem is to implement the PHY timestamping · line 807

Quoted 7 lines · Vladimir Oltean
Documentation/networking/timestamping.rst +7 -0
+When the interface they represent offers both ``SOF_TIMESTAMPING_TX_HARDWARE``
+and ``SOF_TIMESTAMPING_TX_SOFTWARE``.
+Originally, the network stack could deliver either a hardware or a software
+time stamp, but not both. This flag prevents software timestamp delivery.
+This restriction was eventually lifted via the ``SOF_TIMESTAMPING_OPT_TX_SWHW``
+option, but still the original behavior is preserved as the default.
+

So, this implies that we set this only if both are supported? I thought the intention was to set this flag whenever we start a HW timestamp.

Quoted 5 lines

It's only _required_ when SOF_TIMESTAMPING_TX_SOFTWARE is used, it seems. I had also thought of setting 'SKBTX_IN_PROGRESS' as good practice, but there are many situations where it can do more harm than good.

I guess I've only ever implemented a driver with software timestamping enabled as an option. What sort of issues arise when you have this set? I'm guessing that it's some configuration of stacked devices as in the other cases? If the issue can't be fixed I'd at least like more explanation here, since the prevailing convention is that we set this flag, so understanding when and why it's problematic would be useful.

Quoted 2 lines

Thanks,
Jake

Yes, the problematic cases have to do with stacked PHCs (DSA, PHY). The pattern is that:
- DSA sets SKBTX_IN_PROGRESS
- calls dev_queue_xmit towards the MAC driver
- MAC driver sees SKBTX_IN_PROGRESS, thinks it's the one who set it
- MAC driver delivers TX timestamp
- DSA ends poll or receives TX interrupt, collects its timestamp, and delivers a second TX timestamp
In fact this is explained in a bit more detail in the current timestamping.rst file.
Not only are there existing in-tree drivers that do that (and various subtle variations of it), but new code also has this tendency to take shortcuts and interpret any SKBTX_IN_PROGRESS flag set as being set locally. Good thing it's caught during review most of the time these days. It's an error-prone design.
On the DSA front, 1 driver sets this flag (sja1105) and 3 don't (felix,

Quoted 9 lines

mv88e6xxx, hellcreek). The driver who had trouble because of this flag? sja1105.
On the PHY front, 2 drivers set this flag (mscc_phy, dp83640) and 1 doesn't (ptp_ines). The driver who had trouble? dp83640.
So it's very far from obvious that setting this flag is 'the prevailing convention'. For a MAC driver, that might well be, but for DSA/PHY, there seem to be risks associated with doing that, and driver writers should know what they're signing up for.

Quoted 11 lines

Perhaps the issue is that the MAC driver using SKBTX_IN_PROGRESS as the mechanism for telling if it should deliver a timestamp. Shouldn't they be relying on SKBTX_HW_TSTAMP for the "please timestamp" notification, and then using their own mechanism for forwarding that timestamp once it's complete?

I see a handful of drivers do rely on checking this, but I think that's the real bug here.

Quoted 2 lines

-Vladimir

Yes, indeed, a lot of them are exclusively checking "skb_shinfo(skb)->tx_flags & SKBTX_IN_PROGRESS", without any further verification that they have hardware timestamping enabled in the first place, a lot more than I remembered. Some of the occurrences are actually new.

I think at least part of the reason why this keeps going on is that there aren't any hard and fast rules that say you shouldn't do it. When there isn't even a convincing percentage of DSA/PHY drivers that do set SKBTX_HW_TSTAMP, the chances are pretty low that you'll get a stacked PHC driver that sets the flag, plus a MAC driver that checks for it incorrectly. So people tend to ignore this case. Even though, if stacked DSA drivers started supporting software TX timestamping (which is not unlikely, given the fact that this would also give you compatibility with PHY timestamping), I'm sure things would change, because more people would become aware of the issue once mv88e6xxx starts getting affected.

What I've been trying to do is at least try to get people (especially people who have a lot of XP with 1588 drivers) to agree on a common set of guidelines that are explicitly written down. I think that's step #1.

-Vladimir

#13 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 6 lines · Vladimir Oltean

I think at least part of the reason why this keeps going on is that there aren't any hard and fast rules that say you shouldn't do it. When there isn't even a convincing percentage of DSA/PHY drivers that do set SKBTX_HW_TSTAMP, the chances are pretty low that you'll get a stacked PHC driver that sets the flag, plus a MAC driver that checks for it incorrectly. So people tend to ignore this case.

Right.

Quoted 6 lines

Even though, if stacked
DSA drivers started supporting software TX timestamping (which is not unlikely, given the fact that this would also give you compatibility with PHY timestamping), I'm sure things would change, because more people would become aware of the issue once mv88e6xxx starts getting affected.

I really can't see the utility in having a SW time stamp from a DSA interface. The whole point of DSA time stamping is to get the ingress and egress time of frames on the external ports, in order to correct for the residence time within the switch.

Thanks,
Richard

#14 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 17 lines · Richard Cochran
Quoted 6 lines · Vladimir Oltean

I think at least part of the reason why this keeps going on is that there aren't any hard and fast rules that say you shouldn't do it. When there isn't even a convincing percentage of DSA/PHY drivers that do set SKBTX_HW_TSTAMP, the chances are pretty low that you'll get a stacked PHC driver that sets the flag, plus a MAC driver that checks for it incorrectly. So people tend to ignore this case.

Right.

Quoted 6 lines

Even though, if stacked
DSA drivers started supporting software TX timestamping (which is not unlikely, given the fact that this would also give you compatibility with PHY timestamping), I'm sure things would change, because more people would become aware of the issue once mv88e6xxx starts getting affected.

Quoted 7 lines

I really can't see the utility in having a SW time stamp from a DSA interface. The whole point of DSA time stamping is to get the ingress and egress time of frames on the external ports, in order to correct for the residence time within the switch.

Thanks,
Richard

I understand where this is coming from. The DSA software data path is the mirror image of the hardware data path: first the net device corresponding to the switch port, then the net device corresponding to the host port, then the physical host port, then the physical switch port. So, just as hardware timestamping makes the most sense on the outermost PHC, software timestamping makes the most sense on the innermost driver, the last frontier before the packet leaves software hands. That is clear.

But I feel that going as far as saying that 'DSA shouldn't set SKBTX_IN_PROGRESS because it already offers hardware timestamping' is wrong. A software timestamp provided by a DSA net device is just as valuable (or not, depending on your needs) as a software timestamp provided by any other net device. For example, to the people doing TCP time stamping, this software timestamp is just 'the driver timestamp', so it makes perfect sense to have it just where it is: in DSA. Not only that, but we shouldn't completely rule out the idea of software TX timestamps in DSA _and_ in the host interface for the same packet, either, since that could form the basis for some nice benchmarking.

Not only that, but with PHY timestamping, one popular way of handling TX hardware timestamps from a PHY is to call skb_tx_timestamp(). It is nonsense to me, and counterproductive, to end up having that in the code, but not claim SOF_TIMESTAMPING_TX_SOFTWARE support. And PHY timestamping with DSA is not a contradiction in terms by any means, on the contrary, it makes just as much sense as PHY timestamping in general.

So I think the position of "just don't have software timestamping code in DSA and you'll be fine" won't be getting us anywhere. Either you can or you can't, and there isn't anything absurd about it, so sooner or later somebody will want to do it. The rules surrounding it, however, are far from being ready, or clear.

Am I missing something?

Thanks,
-Vladimir

#15 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 7 lines · Vladimir Oltean

So I think the position of "just don't have software timestamping code in DSA and you'll be fine" won't be getting us anywhere. Either you can or you can't, and there isn't anything absurd about it, so sooner or later somebody will want to do it. The rules surrounding it, however, are far from being ready, or clear.

Am I missing something?

I'm just trying to make things easy for you, as the author of DSA drivers. There is no need to set skb flags that have no purpose within the stack.

Nobody is demanding software time stamps from any DSA devices yet, and so I don't see the point in solving a problem that doesn't exist.

I'm sorry if the "rules" are not clear, but if you look around the kernel internals, you will be hard pressed to find perfectly documented rules anywhere!

Thanks,
Richard

#16 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

Quoted 16 lines · Richard Cochran
Quoted 7 lines · Vladimir Oltean

So I think the position of "just don't have software timestamping code in DSA and you'll be fine" won't be getting us anywhere. Either you can or you can't, and there isn't anything absurd about it, so sooner or later somebody will want to do it. The rules surrounding it, however, are far from being ready, or clear.

Am I missing something?

I'm just trying to make things easy for you, as the author of DSA drivers. There is no need to set skb flags that have no purpose within the stack.

Nobody is demanding software time stamps from any DSA devices yet, and so I don't see the point in solving a problem that doesn't exist.

Quoted 6 lines

I'm sorry if the "rules" are not clear, but if you look around the kernel internals, you will be hard pressed to find perfectly documented rules anywhere!

Thanks,
Richard

Could we perhaps take a step back and see what can be improved about the documentation updates?

Thanks,
-Vladimir

#17 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

In reply to Vladimir Oltean

On 7/20/2020 3:13 PM, Vladimir Oltean wrote:>

Quoted 18 lines

Yes, indeed, a lot of them are exclusively checking "skb_shinfo(skb)->tx_flags & SKBTX_IN_PROGRESS", without any further verification that they have hardware timestamping enabled in the first place, a lot more than I remembered. Some of the occurrences are actually new.

I think at least part of the reason why this keeps going on is that there aren't any hard and fast rules that say you shouldn't do it. When there isn't even a convincing percentage of DSA/PHY drivers that do set SKBTX_HW_TSTAMP, the chances are pretty low that you'll get a stacked PHC driver that sets the flag, plus a MAC driver that checks for it incorrectly. So people tend to ignore this case. Even though, if stacked DSA drivers started supporting software TX timestamping (which is not unlikely, given the fact that this would also give you compatibility with PHY timestamping), I'm sure things would change, because more people would become aware of the issue once mv88e6xxx starts getting affected.

Quoted 6 lines

What I've been trying to do is at least try to get people (especially people who have a lot of XP with 1588 drivers) to agree on a common set of guidelines that are explicitly written down. I think that's step #1.

-Vladimir

Right. I think the guideline should be:

This flag indicates to the stack whether or not a hardware Tx timestamp has been started. It's primary purpose is to prevent sending software timestamps if a hw timestamp is provided.

1) set the flag whenever you start a tx timestamp

2) do not assume you are the only driver that will set the flag for a given skb. Use a separate mechanism to decide if that skb is supposed to have a timestamp.

#18 lore raw

Re: [PATCH net-next 3/3] docs: networking: timestamping: add a set of frequently asked questions

In reply to Vladimir Oltean
Quoted 4 lines · Vladimir Oltean

Yes, the problematic cases have to do with stacked PHCs (DSA, PHY). The pattern is that:
- DSA sets SKBTX_IN_PROGRESS

Nit: DSA should _not_ set this bit (but a PHY/MII device should).

Quoted 10 lines

- calls dev_queue_xmit towards the MAC driver
- MAC driver sees SKBTX_IN_PROGRESS, thinks it's the one who set it
- MAC driver delivers TX timestamp
- DSA ends poll or receives TX interrupt, collects its timestamp, and delivers a second TX timestamp

So it's very far from obvious that setting this flag is 'the prevailing convention'. For a MAC driver, that might well be, but for DSA/PHY, there seem to be risks associated with doing that, and driver writers should know what they're signing up for.

The flag only exists to prevent the stack from delivering SW time stamps when HW time stamps are active. If an interface doesn't provide SW time stamps (like DSA interfaces), then there is no need to set the flag.

For MAC and PHY/MII time stamping, they must co-operate, meaning that the MAC driver must be prepared to deal with the fact that the PHY/MII might set this flag. Many MAC drivers don't do this correctly, but there are very few PHY/MII actually in use, and so very few authors of MAC drivers have paid attention to this.

Thanks,
Richard

#19 lore raw
In reply to Vladimir Oltean
Quoted 5 lines · Vladimir Oltean

I've tried to collect and summarize the conclusions of these discussions:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
which were a bit surprising to me. Make sure they are present in the documentation.

As one of participants of these discussions, I'm afraid I incline to alternative approach to solving the issues current design has than the one you advocate in these patch series.

I believe its upper-level that should enforce common policies like handling hw time stamping at outermost capable device, not random MAC driver out there.

I'd argue that it's then upper-level that should check PHY features, and then do not bother MAC with ioctl() requests that MAC should not handle in given configuration. This way, the checks for phy_has_hwtstamp() won't be spread over multiple MAC drivers and will happily sit in the upper-level ioctl() handler.

In other words, I mean that it's approach taken in ethtool that I tend to consider being the right one.

Thanks,
-- Sergey

#20 lore raw
Quoted 22 lines · Sergey Organov
Quoted 5 lines · Vladimir Oltean

I've tried to collect and summarize the conclusions of these discussions:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
which were a bit surprising to me. Make sure they are present in the documentation.

As one of participants of these discussions, I'm afraid I incline to alternative approach to solving the issues current design has than the one you advocate in these patch series.

I believe its upper-level that should enforce common policies like handling hw time stamping at outermost capable device, not random MAC driver out there.

I'd argue that it's then upper-level that should check PHY features, and then do not bother MAC with ioctl() requests that MAC should not handle in given configuration. This way, the checks for phy_has_hwtstamp() won't be spread over multiple MAC drivers and will happily sit in the upper-level ioctl() handler.

Quoted 5 lines

In other words, I mean that it's approach taken in ethtool that I tend to consider being the right one.

Thanks,
-- Sergey

Concretely speaking, what are you going to do for skb_defer_tx_timestamp() and skb_defer_rx_timestamp()? Not to mention subtle bugs like SKBTX_IN_PROGRESS. If you don't address those, it's pointless to move the phy_has_hwtstamp() check to net/core/dev_ioctl.c.

The only way I see to fix the bug is to introduce a new netdev flag, NETIF_F_PHY_HWTSTAMP or something like that. Then I'd grep for all occurrences of phy_has_hwtstamp() in the kernel (which currently amount to a whopping 2 users, 3 with your FEC "fix"), and declare this netdevice flag in their list of features. Then, phy_has_hwtstamp() and phy_has_tsinfo() and what not can be moved to generic places (or at least, I think they can), and those places could proceed to advertise and enable PHY timestamping only if the MAC declared itself ready. But, it is a bit strange to introduce a netdev flag just to fix a bug, I think.

Thanks,
-Vladimir

#21 lore raw
Quoted 34 lines · Vladimir Oltean
Quoted 22 lines · Sergey Organov
Quoted 5 lines · Vladimir Oltean

I've tried to collect and summarize the conclusions of these discussions:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
which were a bit surprising to me. Make sure they are present in the documentation.

As one of participants of these discussions, I'm afraid I incline to alternative approach to solving the issues current design has than the one you advocate in these patch series.

I believe its upper-level that should enforce common policies like handling hw time stamping at outermost capable device, not random MAC driver out there.

I'd argue that it's then upper-level that should check PHY features, and then do not bother MAC with ioctl() requests that MAC should not handle in given configuration. This way, the checks for phy_has_hwtstamp() won't be spread over multiple MAC drivers and will happily sit in the upper-level ioctl() handler.

Quoted 5 lines

In other words, I mean that it's approach taken in ethtool that I tend to consider being the right one.

Thanks,
-- Sergey

Concretely speaking, what are you going to do for skb_defer_tx_timestamp() and skb_defer_rx_timestamp()? Not to mention subtle bugs like SKBTX_IN_PROGRESS. If you don't address those, it's pointless to move the phy_has_hwtstamp() check to net/core/dev_ioctl.c.

Quoted 11 lines

The only way I see to fix the bug is to introduce a new netdev flag, NETIF_F_PHY_HWTSTAMP or something like that. Then I'd grep for all occurrences of phy_has_hwtstamp() in the kernel (which currently amount to a whopping 2 users, 3 with your FEC "fix"), and declare this netdevice flag in their list of features. Then, phy_has_hwtstamp() and phy_has_tsinfo() and what not can be moved to generic places (or at least, I think they can), and those places could proceed to advertise and enable PHY timestamping only if the MAC declared itself ready. But, it is a bit strange to introduce a netdev flag just to fix a bug, I think.

This approach doesn't seem bad to me. We then document that NETIF_F_PHY_HWTSTAMP should only set of the correct conditions are met.

Quoted 3 lines

Thanks,
-Vladimir

#22 lore raw
In reply to Vladimir Oltean
Quoted 26 lines · Vladimir Oltean
Quoted 25 lines · Sergey Organov
Quoted 5 lines · Vladimir Oltean

I've tried to collect and summarize the conclusions of these discussions:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
which were a bit surprising to me. Make sure they are present in the documentation.

As one of participants of these discussions, I'm afraid I incline to alternative approach to solving the issues current design has than the one you advocate in these patch series.

I believe its upper-level that should enforce common policies like handling hw time stamping at outermost capable device, not random MAC driver out there.

I'd argue that it's then upper-level that should check PHY features, and then do not bother MAC with ioctl() requests that MAC should not handle in given configuration. This way, the checks for phy_has_hwtstamp() won't be spread over multiple MAC drivers and will happily sit in the upper-level ioctl() handler.

In other words, I mean that it's approach taken in ethtool that I tend to consider being the right one.

Quoted 6 lines
Quoted 2 lines

Thanks,
-- Sergey

Concretely speaking, what are you going to do for skb_defer_tx_timestamp() and skb_defer_rx_timestamp()? Not to mention subtle bugs like SKBTX_IN_PROGRESS.

I think that we have at least 2 problems here, and what I argue about above addresses one of them, while you try to get solution for another one.

Quoted 2 lines

If you don't address those, it's pointless to move the phy_has_hwtstamp() check to net/core/dev_ioctl.c.

No, even though solving one problem could be considered pointless without solving another, it doesn't mean that solving it is pointless. I do hope you will solve another one.

I believe that logic in ethtool ioctl handling should be moved to clocks subsystem ioctl handling, and then ethtool should simply forward relevant calls to clocks subsystem. This will give us single implementation point that defines which ioctls go to which clocks, and single point where policy decisions are made, that, besides getting rid of current inconsistencies, will allow for easier changes of policies in the future.

That also could be the point that caches time stamping configuration and gives it back to user space by ioctl request, freeing each driver from implementing it, along with copying request structures to/from user space that currently is done in every driver.

I believe such changes are valuable despite particular way the SKBTX_IN_PROGRESS issue will be resolved.

Quoted 10 lines

The only way I see to fix the bug is to introduce a new netdev flag, NETIF_F_PHY_HWTSTAMP or something like that. Then I'd grep for all occurrences of phy_has_hwtstamp() in the kernel (which currently amount to a whopping 2 users, 3 with your FEC "fix"), and declare this netdevice flag in their list of features. Then, phy_has_hwtstamp() and phy_has_tsinfo() and what not can be moved to generic places (or at least, I think they can), and those places could proceed to advertise and enable PHY timestamping only if the MAC declared itself ready. But, it is a bit strange to introduce a netdev flag just to fix a bug, I think.

To me this sounds like a plan.

In general (please don't take it as direct proposal to fix current issues), the most flexible solution would be to allow for user space to select which units will be time stamping (kernel clock being simply one of them), and to deliver all the time stamps to the user space. This will need clock IDs to be delivered along with time stamps (that is a nice thing to have by itself, as I already mentioned elsewhere in previous discussions.) For now it's just a raw idea, nevertheless to me it sounds like a suitable goal for future design.

Thanks,
-- Sergey

#23 lore raw
Quoted 84 lines · Sergey Organov
Quoted 26 lines · Vladimir Oltean
Quoted 25 lines · Sergey Organov
Quoted 5 lines · Vladimir Oltean

I've tried to collect and summarize the conclusions of these discussions:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
which were a bit surprising to me. Make sure they are present in the documentation.

As one of participants of these discussions, I'm afraid I incline to alternative approach to solving the issues current design has than the one you advocate in these patch series.

I believe its upper-level that should enforce common policies like handling hw time stamping at outermost capable device, not random MAC driver out there.

I'd argue that it's then upper-level that should check PHY features, and then do not bother MAC with ioctl() requests that MAC should not handle in given configuration. This way, the checks for phy_has_hwtstamp() won't be spread over multiple MAC drivers and will happily sit in the upper-level ioctl() handler.

In other words, I mean that it's approach taken in ethtool that I tend to consider being the right one.

Quoted 6 lines
Quoted 2 lines

Thanks,
-- Sergey

Concretely speaking, what are you going to do for skb_defer_tx_timestamp() and skb_defer_rx_timestamp()? Not to mention subtle bugs like SKBTX_IN_PROGRESS.

I think that we have at least 2 problems here, and what I argue about above addresses one of them, while you try to get solution for another one.

Quoted 2 lines

If you don't address those, it's pointless to move the phy_has_hwtstamp() check to net/core/dev_ioctl.c.

No, even though solving one problem could be considered pointless without solving another, it doesn't mean that solving it is pointless. I do hope you will solve another one.

I believe that logic in ethtool ioctl handling should be moved to clocks subsystem ioctl handling, and then ethtool should simply forward relevant calls to clocks subsystem. This will give us single implementation point that defines which ioctls go to which clocks, and single point where policy decisions are made, that, besides getting rid of current inconsistencies, will allow for easier changes of policies in the future.

That also could be the point that caches time stamping configuration and gives it back to user space by ioctl request, freeing each driver from implementing it, along with copying request structures to/from user space that currently is done in every driver.

I believe such changes are valuable despite particular way the SKBTX_IN_PROGRESS issue will be resolved.

Quoted 10 lines

The only way I see to fix the bug is to introduce a new netdev flag, NETIF_F_PHY_HWTSTAMP or something like that. Then I'd grep for all occurrences of phy_has_hwtstamp() in the kernel (which currently amount to a whopping 2 users, 3 with your FEC "fix"), and declare this netdevice flag in their list of features. Then, phy_has_hwtstamp() and phy_has_tsinfo() and what not can be moved to generic places (or at least, I think they can), and those places could proceed to advertise and enable PHY timestamping only if the MAC declared itself ready. But, it is a bit strange to introduce a netdev flag just to fix a bug, I think.

To me this sounds like a plan.

In general (please don't take it as direct proposal to fix current issues), the most flexible solution would be to allow for user space to select which units will be time stamping (kernel clock being simply one of them), and to deliver all the time stamps to the user space. This will need clock IDs to be delivered along with time stamps (that is a nice thing to have by itself, as I already mentioned elsewhere in previous discussions.) For now it's just a raw idea, nevertheless to me it sounds like a suitable goal for future design.

Quoted 2 lines

Thanks,
-- Sergey

To me, there's one big inconsistency I see between your position when you were coming from a 4.9 kernel where you wanted to fix a bug, and your position now.

Your position when _you_ wanted to solve a problem for yourself was:

  |You see, I have a problem on kernel 4.9.146. After I apply this patch,
  |the problem goes away, at least for FEC/PHY combo that I care about, and
  |chances are high that for DSA as well, according to your own expertise.
  |Why should I care what is or is not ready for what to get a bug-fix
  |patch into the kernel? Why should I guess some vague "intentions" or
  |spend my time elsewhere?

As I said in that email thread, I can't contradict you. It is a design limitation which right now I am simply documenting. That design limitation is there to stay in stable kernels: I don't think there is any way to backport a new flag to netdev_features_t to kernels as old as 4.9 and such. If you think there is, please say so, that would change things quite a lot.

And now, you're arguing that I shouldn't be documenting the design limitation, I should be fixing it. Maybe I will, but first of all, you're asking me to effectively close the door for anybody else in your position. On one side you proved that PHY timestamping is something that should have been working, and now you're treating it as something which shouldn't be.

You can argue that we can keep accepting bug fixes to this problem for stable kernels, and in that case I don't see why you're arguing that we shouldn't be documenting the design limitation.

Nobody said things are set in stone, I'm simply recording where we are today and I'll be making further changes to the documentation as things progress.

Thanks,
-Vladimir

#24 lore raw
Quoted 86 lines · Vladimir Oltean
Quoted 85 lines · Sergey Organov
Quoted 27 lines · Vladimir Oltean
Quoted 26 lines · Sergey Organov
Quoted 6 lines · Vladimir Oltean

I've tried to collect and summarize the conclusions of these discussions:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
which were a bit surprising to me. Make sure they are present in the documentation.

As one of participants of these discussions, I'm afraid I incline to alternative approach to solving the issues current design has than the one you advocate in these patch series.

I believe its upper-level that should enforce common policies like handling hw time stamping at outermost capable device, not random MAC driver out there.

I'd argue that it's then upper-level that should check PHY features, and then do not bother MAC with ioctl() requests that MAC should not handle in given configuration. This way, the checks for phy_has_hwtstamp() won't be spread over multiple MAC drivers and will happily sit in the upper-level ioctl() handler.

In other words, I mean that it's approach taken in ethtool that I tend to consider being the right one.

Quoted 6 lines
Quoted 2 lines

Thanks,
-- Sergey

Concretely speaking, what are you going to do for skb_defer_tx_timestamp() and skb_defer_rx_timestamp()? Not to mention subtle bugs like SKBTX_IN_PROGRESS.

I think that we have at least 2 problems here, and what I argue about above addresses one of them, while you try to get solution for another one.

Quoted 2 lines

If you don't address those, it's pointless to move the phy_has_hwtstamp() check to net/core/dev_ioctl.c.

No, even though solving one problem could be considered pointless without solving another, it doesn't mean that solving it is pointless. I do hope you will solve another one.

I believe that logic in ethtool ioctl handling should be moved to clocks subsystem ioctl handling, and then ethtool should simply forward relevant calls to clocks subsystem. This will give us single implementation point that defines which ioctls go to which clocks, and single point where policy decisions are made, that, besides getting rid of current inconsistencies, will allow for easier changes of policies in the future.

That also could be the point that caches time stamping configuration and gives it back to user space by ioctl request, freeing each driver from implementing it, along with copying request structures to/from user space that currently is done in every driver.

I believe such changes are valuable despite particular way the SKBTX_IN_PROGRESS issue will be resolved.

Quoted 10 lines

The only way I see to fix the bug is to introduce a new netdev flag, NETIF_F_PHY_HWTSTAMP or something like that. Then I'd grep for all occurrences of phy_has_hwtstamp() in the kernel (which currently amount to a whopping 2 users, 3 with your FEC "fix"), and declare this netdevice flag in their list of features. Then, phy_has_hwtstamp() and phy_has_tsinfo() and what not can be moved to generic places (or at least, I think they can), and those places could proceed to advertise and enable PHY timestamping only if the MAC declared itself ready. But, it is a bit strange to introduce a netdev flag just to fix a bug, I think.

To me this sounds like a plan.

In general (please don't take it as direct proposal to fix current issues), the most flexible solution would be to allow for user space to select which units will be time stamping (kernel clock being simply one of them), and to deliver all the time stamps to the user space. This will need clock IDs to be delivered along with time stamps (that is a nice thing to have by itself, as I already mentioned elsewhere in previous discussions.) For now it's just a raw idea, nevertheless to me it sounds like a suitable goal for future design.

Quoted 6 lines
Quoted 2 lines

Thanks,
-- Sergey

To me, there's one big inconsistency I see between your position when you were coming from a 4.9 kernel where you wanted to fix a bug, and your position now.

[First of all, as it seems there is misunderstanding here, let me say right from beginning that I have nothing against documenting current status, I'm rather all in favor of it, and I do appreciate your work on it very much, and I believe I already said this in a reply to your previous documentation patch some time ago.]

Inconsistency? I don't think so. One thing is to fix a bug within current design limitations, and another one -- suggest design improvements that should make things better in the future. I just talk about different matters.

Quoted 11 lines

Your position when _you_ wanted to solve a problem for yourself was:

  |You see, I have a problem on kernel 4.9.146. After I apply this patch,
  |the problem goes away, at least for FEC/PHY combo that I care about, and
  |chances are high that for DSA as well, according to your own expertise.
  |Why should I care what is or is not ready for what to get a bug-fix
  |patch into the kernel? Why should I guess some vague "intentions" or
  |spend my time elsewhere?

As I said in that email thread, I can't contradict you.

I fail to see what this has to do with current discussion. Apparently I was not able to make my current intentions clear enough, but I try again below.

Quoted 5 lines

It is a design limitation which right now I am simply documenting. That design limitation is there to stay in stable kernels: I don't think there is any way to backport a new flag to netdev_features_t to kernels as old as 4.9 and such. If you think there is, please say so, that would change things quite a lot.

I didn't even think about it, sorry, don't know how you figured I have an opinion about it.

Quoted 2 lines

And now, you're arguing that I shouldn't be documenting the design limitation, I should be fixing it.

No, I'm not. In case you just document them, no. If you also suggest some road for improvements that I don't agree on, only then I argue.

Quoted 4 lines

Maybe I will, but first of all, you're asking me to effectively close the door for anybody else in your position. On one side you proved that PHY timestamping is something that should have been working, and now you're treating it as something which shouldn't be.

I'm not asking you for anything, no. I just shared my thoughts on the issue of proper ways to improve overall design. You are free to disagree or even to ignore them.

Quoted 3 lines

You can argue that we can keep accepting bug fixes to this problem for stable kernels, and in that case I don't see why you're arguing that we shouldn't be documenting the design limitation.

You don't see because I'm not. I'm all for documenting.

I just got an impression that you also suggest ways to improve the design, and, based on your comment that ethtool way is the bad design as it doesn't consult MAC when handling ioctls, I was afraid the design might went into direction I don't agree with.

Maybe I got your intentions wrong. Sorry if I did.

Quoted 4 lines

Nobody said things are set in stone, I'm simply recording where we are today and I'll be making further changes to the documentation as things progress.

I have absolutely nothing against documenting current status, not at all. Moreover, as I think I already said in this thread, your recent idea about NETIF_F_PHY_HWTSTAMP seemed sound to me too.

I'm sorry I managed to provoke so much worry on your side!

Thanks,
-- Sergey

#25 lore raw
In reply to Vladimir Oltean
Quoted 5 lines · Vladimir Oltean

I've tried to collect and summarize the conclusions of these discussions:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
which were a bit surprising to me. Make sure they are present in the documentation.

By the way, there is another somewhat related issue that needs to be addressed. I believe kernel needs to free user space from this trick found even in kernel sources themselves:

tools/testing/selftests/ptp/testptp.c:87:

static clockid_t get_clockid(int fd)
{

#define CLOCKFD 3
        return (((unsigned int) ~fd) << 3) | CLOCKFD;
}

Once upon a time there was a patch for that, but I don't think it addressed the issue correctly, here is more background:

https://lore.kernel.org/lkml/[email protected]/

Thanks,
-- Sergey