arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes
Subsystems (2)
Vignesh Raghavendra
maintainerPATCH 1/1 arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes
8250_omap compatible UART IPs on all SoCs have registers aligned at 4 byte address boundary and constant byte addressability. Thus there is no need for reg-io-width or reg-shift DT properties. These properties are not used by 8250_omap driver nor documented as part of binding document. Therefore drop them.
This is in preparation to move omap-serial.txt to YAML format.
--- arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 14 ------------- arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi | 4 ---- arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 6 ------ arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi | 2 -- arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 -- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 20 ------------------- .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 4 ---- arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 20 ------------------- .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ---- 9 files changed, 76 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +0 -14
@@ -189,8 +189,6 @@ phy_gmii_sel: phy@4044 { main_uart0: serial@2800000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02800000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -202,8 +200,6 @@ main_uart0: serial@2800000 { main_uart1: serial@2810000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02810000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -215,8 +211,6 @@ main_uart1: serial@2810000 { main_uart2: serial@2820000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02820000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -228,8 +222,6 @@ main_uart2: serial@2820000 { main_uart3: serial@2830000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02830000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -241,8 +233,6 @@ main_uart3: serial@2830000 { main_uart4: serial@2840000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02840000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -254,8 +244,6 @@ main_uart4: serial@2840000 { main_uart5: serial@2850000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02850000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -267,8 +255,6 @@ main_uart5: serial@2850000 { main_uart6: serial@2860000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02860000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi +0 -4
@@ -9,8 +9,6 @@ &cbass_mcu { mcu_uart0: serial@4a00000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x04a00000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -22,8 +20,6 @@ mcu_uart0: serial@4a00000 { mcu_uart1: serial@4a10000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x04a10000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
arch/arm64/boot/dts/ti/k3-am65-main.dtsi +0 -6
@@ -84,8 +84,6 @@ serdes1: serdes@910000 { main_uart0: serial@2800000 { compatible = "ti,am654-uart"; reg = <0x00 0x02800000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -95,8 +93,6 @@ main_uart0: serial@2800000 { main_uart1: serial@2810000 { compatible = "ti,am654-uart"; reg = <0x00 0x02810000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
@@ -105,8 +101,6 @@ main_uart1: serial@2810000 { main_uart2: serial@2820000 { compatible = "ti,am654-uart"; reg = <0x00 0x02820000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi +0 -2
@@ -23,8 +23,6 @@ phy_gmii_sel: phy@4040 { mcu_uart0: serial@40a00000 { compatible = "ti,am654-uart"; reg = <0x00 0x40a00000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 565 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <96000000>; current-speed = <115200>;
arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi +0 -2
@@ -50,8 +50,6 @@ wkup_pmx0: pinctrl@4301c000 { wkup_uart0: serial@42300000 { compatible = "ti,am654-uart"; reg = <0x42300000 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +0 -20
@@ -301,8 +301,6 @@ main_pmx0: pinctrl@11c000 { main_uart0: serial@2800000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02800000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -314,8 +312,6 @@ main_uart0: serial@2800000 { main_uart1: serial@2810000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02810000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -327,8 +323,6 @@ main_uart1: serial@2810000 { main_uart2: serial@2820000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02820000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -340,8 +334,6 @@ main_uart2: serial@2820000 { main_uart3: serial@2830000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02830000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -353,8 +345,6 @@ main_uart3: serial@2830000 { main_uart4: serial@2840000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02840000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -366,8 +356,6 @@ main_uart4: serial@2840000 { main_uart5: serial@2850000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02850000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -379,8 +367,6 @@ main_uart5: serial@2850000 { main_uart6: serial@2860000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02860000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -392,8 +378,6 @@ main_uart6: serial@2860000 { main_uart7: serial@2870000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02870000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -405,8 +389,6 @@ main_uart7: serial@2870000 { main_uart8: serial@2880000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02880000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -418,8 +400,6 @@ main_uart8: serial@2880000 { main_uart9: serial@2890000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02890000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +0 -4
@@ -73,8 +73,6 @@ mcu_ram: sram@41c00000 { wkup_uart0: serial@42300000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x42300000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -86,8 +84,6 @@ wkup_uart0: serial@42300000 { mcu_uart0: serial@40a00000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x40a00000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <96000000>; current-speed = <115200>;
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +0 -20
@@ -775,8 +775,6 @@ pcie3_ep: pcie-ep@2930000 { main_uart0: serial@2800000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02800000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -788,8 +786,6 @@ main_uart0: serial@2800000 { main_uart1: serial@2810000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02810000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -801,8 +797,6 @@ main_uart1: serial@2810000 { main_uart2: serial@2820000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02820000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -814,8 +808,6 @@ main_uart2: serial@2820000 { main_uart3: serial@2830000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02830000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -827,8 +819,6 @@ main_uart3: serial@2830000 { main_uart4: serial@2840000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02840000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -840,8 +830,6 @@ main_uart4: serial@2840000 { main_uart5: serial@2850000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02850000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -853,8 +841,6 @@ main_uart5: serial@2850000 { main_uart6: serial@2860000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02860000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -866,8 +852,6 @@ main_uart6: serial@2860000 { main_uart7: serial@2870000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02870000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -879,8 +863,6 @@ main_uart7: serial@2870000 { main_uart8: serial@2880000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02880000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -892,8 +874,6 @@ main_uart8: serial@2880000 { main_uart9: serial@2890000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02890000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi +0 -4
@@ -73,8 +73,6 @@ mcu_ram: sram@41c00000 { wkup_uart0: serial@42300000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x42300000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; current-speed = <115200>;
@@ -86,8 +84,6 @@ wkup_uart0: serial@42300000 { mcu_uart0: serial@40a00000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x40a00000 0x00 0x100>; - reg-shift = <2>; - reg-io-width = <4>; interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <96000000>; current-speed = <115200>;
Signature · 1 line
2.31.1
Quoted 9 lines · Vignesh Raghavendra
8250_omap compatible UART IPs on all SoCs have registers aligned at 4 byte address boundary and constant byte addressability. Thus there is no need for reg-io-width or reg-shift DT properties. These properties are not used by 8250_omap driver nor documented as part of binding document. Therefore drop them.
This is in preparation to move omap-serial.txt to YAML format.
Signed-off-by Vignesh Raghavendra <[email protected]>
Thanks and regards,
Lokesh
Quoted 7 lines · Vignesh Raghavendra
8250_omap compatible UART IPs on all SoCs have registers aligned at 4 byte address boundary and constant byte addressability. Thus there is no need for reg-io-width or reg-shift DT properties. These properties are not used by 8250_omap driver nor documented as part of binding document. Therefore drop them.
This is in preparation to move omap-serial.txt to YAML format.
Hi Vignesh Raghavendra,
I have applied the following to branch ti-k3-dts-next on [1]. Thank you!
[1/1] arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes
commit: 53af668e7c154c33f69e3f631261155b0cf2a784
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
[1] git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux.git
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D