Skip to contentSkip to conversation

Q40 IDE fixes

PATCH Applied Michael Schmitz 2 participants 5 messages Aug 27, 2023 – Aug 28, 2023

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v6 cover Q40 IDE fixes

Version 6 of the pata_falcon bugfix patch for Q40 support, addressing the latest comments by Geert and Damien.

No logic changes from v5 which was tested by William.

Cheers,

Michael

#1 lore raw

PATCH v6 1/2 ata: pata_falcon: fix IO base selection for Q40

With commit 44b1fbc0f5f3 ("m68k/q40: Replace q40ide driver with pata_falcon and falconide"), the Q40 IDE driver was replaced by pata_falcon.c.

Both IO and memory resources were defined for the Q40 IDE platform device, but definition of the IDE register addresses was modeled after the Falcon case, both in use of the memory resources and in including register shift and byte vs. word offset in the address.

This was correct for the Falcon case, which does not apply any address translation to the register addresses. In the Q40 case, all of device base address, byte access offset and register shift is included in the platform specific ISA access translation (in asm/mm_io.h).

As a consequence, such address translation gets applied twice, and register addresses are mangled.

Use the device base address from the platform IO resource for Q40 (the IO address translation will then add the correct ISA window base address and byte access offset), with register shift 1. Use MMIO base address and register shift 2 as before for Falcon.

Encode PIO_OFFSET into IO port addresses for all registers for Q40 except the data transfer register. Encode the MMIO offset there (pata_falcon_data_xfer() directly uses raw IO with no address translation).

---

Changes from v4:

Geert Uytterhoeven:
- use %px for ap->ioaddr.data_addr

Changes from v3:

Sergey Shtylyov:
- change use of reg_scale to reg_shift

Geert Uytterhoeven:
- factor out ata_port_desc() from platform specific code

Changes from v2:

Finn Thain:
- add back stable Cc:

Changes from v1:

Damien Le Moal:
- change patch title
- drop stable backport tag

Changes from RFC v3:

- split off byte swap option into separate patch

Geert Uytterhoeven:
- review comments

Changes from RFC v2:
- add driver parameter 'data_swap' as bit mask for drives to swap

Changes from RFC v1:

Finn Thain:
- take care to supply IO address suitable for ioread8/iowrite8
- use MMIO address for data transfer

---
 drivers/ata/pata_falcon.c | 50 +++++++++++++++++++++++----------------
 1 file changed, 29 insertions(+), 21 deletions(-)
drivers/ata/pata_falcon.c +29 -21
index 996516e64f13..616064b02de6 100644
@@ -123,8 +123,8 @@ static int __init pata_falcon_init_one(struct platform_device *pdev)
 	struct resource *base_res, *ctl_res, *irq_res;
 	struct ata_host *host;
 	struct ata_port *ap;
-	void __iomem *base;
-	int irq = 0;
+	void __iomem *base, *ctl_base;
+	int irq = 0, io_offset = 1, reg_shift = 2; /* Falcon defaults */
 
 	dev_info(&pdev->dev, "Atari Falcon and Q40/Q60 PATA controller\n");
 
@@ -165,26 +165,34 @@ static int __init pata_falcon_init_one(struct platform_device *pdev)
 	ap->pio_mask = ATA_PIO4;
 	ap->flags |= ATA_FLAG_SLAVE_POSS | ATA_FLAG_NO_IORDY;
 
-	base = (void __iomem *)base_mem_res->start;
 	/* N.B. this assumes data_addr will be used for word-sized I/O only */
-	ap->ioaddr.data_addr		= base + 0 + 0 * 4;
-	ap->ioaddr.error_addr		= base + 1 + 1 * 4;
-	ap->ioaddr.feature_addr		= base + 1 + 1 * 4;
-	ap->ioaddr.nsect_addr		= base + 1 + 2 * 4;
-	ap->ioaddr.lbal_addr		= base + 1 + 3 * 4;
-	ap->ioaddr.lbam_addr		= base + 1 + 4 * 4;
-	ap->ioaddr.lbah_addr		= base + 1 + 5 * 4;
-	ap->ioaddr.device_addr		= base + 1 + 6 * 4;
-	ap->ioaddr.status_addr		= base + 1 + 7 * 4;
-	ap->ioaddr.command_addr		= base + 1 + 7 * 4;
-
-	base = (void __iomem *)ctl_mem_res->start;
-	ap->ioaddr.altstatus_addr	= base + 1;
-	ap->ioaddr.ctl_addr		= base + 1;
-
-	ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx",
-		      (unsigned long)base_mem_res->start,
-		      (unsigned long)ctl_mem_res->start);
+	ap->ioaddr.data_addr = (void __iomem *)base_mem_res->start;
+
+	if (base_res) {		/* only Q40 has IO resources */
+		io_offset = 0x10000;
+		reg_shift = 0;
+		base = (void __iomem *)base_res->start;
+		ctl_base = (void __iomem *)ctl_res->start;
+	} else {
+		base = (void __iomem *)base_mem_res->start;
+		ctl_base = (void __iomem *)ctl_mem_res->start;
+	}
+
+	ap->ioaddr.error_addr	= base + io_offset + (1 << reg_shift);
+	ap->ioaddr.feature_addr	= base + io_offset + (1 << reg_shift);
+	ap->ioaddr.nsect_addr	= base + io_offset + (2 << reg_shift);
+	ap->ioaddr.lbal_addr	= base + io_offset + (3 << reg_shift);
+	ap->ioaddr.lbam_addr	= base + io_offset + (4 << reg_shift);
+	ap->ioaddr.lbah_addr	= base + io_offset + (5 << reg_shift);
+	ap->ioaddr.device_addr	= base + io_offset + (6 << reg_shift);
+	ap->ioaddr.status_addr	= base + io_offset + (7 << reg_shift);
+	ap->ioaddr.command_addr	= base + io_offset + (7 << reg_shift);
+
+	ap->ioaddr.altstatus_addr	= ctl_base + io_offset;
+	ap->ioaddr.ctl_addr		= ctl_base + io_offset;
+
+	ata_port_desc(ap, "cmd %px ctl %px data %px",
+		      base, ctl_base, ap->ioaddr.data_addr);
 
 	irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (irq_res && irq_res->start > 0) {
Signature · 1 line
2.17.1
#2 lore raw

PATCH v6 2/2 ata: pata_falcon: add data_swab option to byte-swap disk data

In reply to Michael Schmitz

Some users of pata_falcon on Q40 have IDE disks in default IDE little endian byte order, whereas legacy disks use host-native big-endian byte order as on the Atari Falcon.

Add module parameter 'data_swab' to allow connecting drives with non-native data byte order. Drives selected by the data_swap bit mask will have their user data byte-swapped to host byte order, i.e. 'pata_falcon.data_swab=2' will byte-swap all user data on drive B, leaving data on drive A in native byte order. On Q40, drives on a second IDE interface may be added to the bit mask as bits 2 and 3.

Default setting is no byte swapping, i.e. compatibility with the native Falcon or Q40 operating system disk format.

---

Changes since v5:

Geert Uytterhoeven:
- correct mask_shift comment

Changes since v4:

Damien Le Moal:
- spell out bitmask shift calculation

Changes since v2:

Geert Uytterhoeven:
- only shift swap bitmask if pdev->id > 0

Finn Thain:
- use pdev->devno directly for byte swap check

Changes since v1:

Damien Le Moal:
- change patch title
- drop swap_data flag

Finn Thain:
- drop allocation of ap->private struct, use field as bitmask

Changes since RFC v4:

Geert Uytterhoeven:
- don't shift static module parameter for drive 3/4 bitmask
- simplify bit mask calculation to always use pdev->id

Finn Thain:
- correct bit numbers for drive 3/4

Changes since RFC v3:

- split off this byte swap handling into separate patch

- add hint regarding third and fourth drive on Q40

Finn Thain:
- rename module parameter to 'data_swab' to better reflect its use

William Sowerbutts:
- correct IDE drive number used in data swap conditional

---
 drivers/ata/pata_falcon.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
drivers/ata/pata_falcon.c +11 -1
index 616064b02de6..e3a0aa384f59 100644
@@ -33,6 +33,11 @@
 #define DRV_NAME "pata_falcon"
 #define DRV_VERSION "0.1.0"
 
+static int pata_falcon_swap_mask;
+
+module_param_named(data_swab, pata_falcon_swap_mask, int, 0444);
+MODULE_PARM_DESC(data_swab, "Data byte swap enable/disable bitmap (0x1==drive1, 0x2==drive2, 0x4==drive3, 0x8==drive4, default==0)");
+
 static const struct scsi_host_template pata_falcon_sht = {
 	ATA_PIO_SHT(DRV_NAME),
 };
@@ -50,7 +55,7 @@ static unsigned int pata_falcon_data_xfer(struct ata_queued_cmd *qc,
 
 	if (dev->class == ATA_DEV_ATA && cmd &&
 	    !blk_rq_is_passthrough(scsi_cmd_to_rq(cmd)))
-		swap = 0;
+		swap = (uintptr_t)ap->private_data & BIT(dev->devno);
 
 	/* Transfer multiple of 2 bytes */
 	if (rw == READ) {
@@ -124,6 +129,7 @@ static int __init pata_falcon_init_one(struct platform_device *pdev)
 	struct ata_host *host;
 	struct ata_port *ap;
 	void __iomem *base, *ctl_base;
+	int mask_shift = 0; /* Q40 & Falcon default */
 	int irq = 0, io_offset = 1, reg_shift = 2; /* Falcon defaults */
 
 	dev_info(&pdev->dev, "Atari Falcon and Q40/Q60 PATA controller\n");
@@ -194,6 +200,10 @@ static int __init pata_falcon_init_one(struct platform_device *pdev)
 	ata_port_desc(ap, "cmd %px ctl %px data %px",
 		      base, ctl_base, ap->ioaddr.data_addr);
 
+	if (pdev->id > 0)
+		mask_shift = 2;
+	ap->private_data = (void *)(uintptr_t)(pata_falcon_swap_mask >> mask_shift);
+
 	irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (irq_res && irq_res->start > 0) {
 		irq = irq_res->start;
Signature · 1 line
2.17.1
maintainer Applied
#3 lore raw
In reply to Michael Schmitz
Quoted 4 lines · Michael Schmitz

Version 6 of the pata_falcon bugfix patch for Q40 support, addressing the latest comments by Geert and Damien.

No logic changes from v5 which was tested by William.

Applied to fo-6.6. Thanks !

Quoted 6 lines

Cheers,

Michael

Signature · 2 lines
Damien Le Moal
Western Digital Research
#4 lore raw

Thanks Damien!

Cheers,

    Michael

Quoted 12 lines · Damien Le Moal
Quoted 4 lines · Michael Schmitz

Version 6 of the pata_falcon bugfix patch for Q40 support, addressing the latest comments by Geert and Damien.

No logic changes from v5 which was tested by William.

Applied to fo-6.6. Thanks !

Quoted 5 lines

Cheers,

Michael