Skip to contentSkip to conversation

About Network Console Protocol and nc/ncb

U-Boot-Users Frederic Kwiatkowski 2 participants 5 messages Mar 16, 2006

lore
Share & tools
lore
#0 lore raw

Hi all

I'm wondering how to use te Network Console Protocol. I've read the README.NetConsole file and discoverd it, but does this feature is available on every boards-configs, such as the at91 one?

I've tried to set the env variable like this:
setenv nc 'setenv stdout nc;setenv stdin nc'
setenv ncip 192.168.0.66 (wich is the board's IP)
run nc

and run the following script on my Linux Computer:
#! /bin/bash

[ $# = 1 ] || { echo "Usage: $0 target_ip" >&2 ; exit 1 ; } TARGET_IP=$1

stty icanon echo intr ^T
./ncb &
nc -u ${TARGET_IP} 6666
stty icanon echo intr ^C
kill 0

but when i try to use ./ncip.sh 192.168.0.66, nothings happen So i thoutgh the ncip have to be the one of my desktop computer, but nothing better

Does anyone have already use this feature?

With regards

Frederic

#1 lore raw
Quoted 5 lines · In message <[email protected]> you wrote:

I'm wondering how to use te Network Console Protocol. I've read the README.NetConsole file and discoverd it, but does this feature is available on every boards-configs, such as the at91 one?

If you enable it, it should work. But only few boards actually use this feature in their default configuration.

Quoted 3 lines

but when i try to use ./ncip.sh 192.168.0.66, nothings happen So i thoutgh the ncip have to be the one of my desktop computer, but nothing better

Run a sniffer (ethereal) on your network and check if you see any packets at all. You *did* switch the stdin / stdout channels in U-Boot, didn't you?

Quoted 1 line

Does anyone have already use this feature?

Yes, it is being used actively on a couple of boards, some of them in production with high volumes.

Best regards,

Wolfgang Denk

Signature · 5 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Programmer's Lament: (Shakespeare, Macbeth, Act I, Scene vii)
        "That we but teach bloody instructions,
        which, being taught, return to plague the inventor..."
#2 lore raw

Thanks for your response

Quoted 6 lines
Quoted 3 lines

I'm wondering how to use te Network Console Protocol. I've read the README.NetConsole file and discoverd it, but does this feature is available on every boards-configs, such as the at91 one?

If you enable it, it should work. But only few boards actually use this feature in their default configuration.

Is there any #define to enable it or must I modify some sources file to do this?

Quoted 8 lines
Quoted 4 lines

but when i try to use ./ncip.sh 192.168.0.66, nothings happen So i thoutgh the ncip have to be the one of my desktop computer, but nothing better

Run a sniffer (ethereal) on your network and check if you see any packets at all. You *did* switch the stdin / stdout channels in U-Boot, didn't you?

if setenv nc 'setenv stdout nc;setenv stdin nc have succed, with run nc, it is switched
But, i've seen with ethereal that no packets where transmited through my eth interface
It might be the first step to solve this problem

Quoted 16 lines
Quoted 1 line

Does anyone have already use this feature?

Yes, it is being used actively on a couple of boards, some of them in production with high volumes.

Best regards,

Wolfgang Denk

--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Programmer's Lament: (Shakespeare, Macbeth, Act I, Scene vii)
"That we but teach bloody instructions,
which, being taught, return to plague the inventor..."

#3 lore raw
Quoted 6 lines · In message <[email protected]> you wrote:
Quoted 3 lines

If you enable it, it should work. But only few boards actually use this feature in their default configuration.

Is there any #define to enable it or must I modify some sources file to do this?

#define CONFIG_NETCONSOLE in your board config file.

Quoted 2 lines

if setenv nc 'setenv stdout nc;setenv stdin nc have succed, with run nc, it is switched

Yes. [And you don't see any more output on the U-Boot console, right?]

Quoted 3 lines

But, i've seen with ethereal that no packets where transmited through my eth interface
It might be the first step to solve this problem

Indeed.

Best regards,

Wolfgang Denk

Signature · 6 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Boss, n.: According to the Oxford English Dictionary, in  the  Middle
Ages  the  words  "boss"  and "botch" were largely synonymous, except
that boss, in addition to meaning  "a  supervisor  of  workers"  also
meant "an ornamental stud."
#4 lore raw

2006/3/16, Wolfgang Denk <[email protected]>:

Quoted 10 lines
Quoted 6 lines · In message <[email protected]> you wrote:
Quoted 3 lines

If you enable it, it should work. But only few boards actually use this feature in their default configuration.

Is there any #define to enable it or must I modify some sources file to do this?

#define CONFIG_NETCONSOLE in your board config file.

I'll try this, and debugging my errors
-Map u-boot.map -o u-boot
drivers/libdrivers.a(netconsole.o): In function `nc_send_packet':
/home/smb/uc-dev/frk/u-boot_051108/drivers/netconsole.c:116: undefined reference to eth_get_dev' drivers/libdrivers.a(netconsole.o): In function nc_tstc':
/home/smb/uc-dev/frk/u-boot_051108/drivers/netconsole.c:233: undefined reference to `eth_get_dev'
make: *** [u-boot] Erreur 1

thanks for all, i hope i should solve my problems now

with regards

Frederic