Skip to contentSkip to conversation

htb and iptables marked packets question

LARTC Felipe Ceglia 3 participants 3 messages Dec 27, 2004 – Dec 28, 2004

lore
Share & tools
lore
#0 lore raw

Hi folks,

I have a strange situation. When I add branches to the tree, everything goes to the default class.
The error might be obvious, but I cannot find it. I would really appreciate your help.

this works, nothing goes to "1:9999":
#############################################################################
/sbin/iptables -F -t mangle
/sbin/tc qdisc del dev eth1 root > /dev/null 2>&1
/sbin/tc qdisc add dev eth1 root handle 1: htb default 9999 /sbin/tc class add dev eth1 parent 1: classid 1:1 htb rate 100Mbit ceil 100Mbit /sbin/tc class add dev eth1 parent 1:1 classid 1:9999 htb rate 128kbit /sbin/tc class add dev eth1 parent 1:1 classid 1:4 htb rate 100Mbit /sbin/tc class add dev eth1 parent 1:4 classid 1:28 htb rate 510kbit #
/sbin/iptables -A POSTROUTING -o eth1 -t mangle -d 192.168.0.0/16 -j MARK --set-mark 4
/sbin/tc filter add dev eth1 protocol ip parent 1:0 prio 3 handle 4 fw flowid 1:4
#
/sbin/iptables -A POSTROUTING -o eth1 -t mangle -d 192.168.200.0/24 -j MARK --set-mark 28
/sbin/tc filter add dev eth1 protocol ip parent 1:0 prio 3 handle 28 fw flowid 1:28
#############################################################################

when I add subclasses to "1:28", traffic goes to "1:34" and "1:35", but exceeding traffic goes to "1:9999" instead of being placed at "1:28":
#############################################################################
/sbin/iptables -F -t mangle

/sbin/tc qdisc del dev eth1 root > /dev/null 2>&1
/sbin/tc qdisc add dev eth1 root handle 1: htb default 9999 /sbin/tc class add dev eth1 parent 1: classid 1:1 htb rate 100Mbit ceil 100Mbit /sbin/tc class add dev eth1 parent 1:1 classid 1:9999 htb rate 128kbit /sbin/tc class add dev eth1 parent 1:1 classid 1:4 htb rate 100Mbit /sbin/iptables -A POSTROUTING -o eth1 -t mangle -d 192.168.0.0/16 -j MARK --set-mark 4
/sbin/tc filter add dev eth1 protocol ip parent 1:0 prio 3 handle 4 fw flowid 1:4
#
/sbin/tc class add dev eth1 parent 1:4 classid 1:28 htb rate 510kbit /sbin/iptables -A POSTROUTING -o eth1 -t mangle -d 192.168.200.0/24 -j MARK --set-mark 28
/sbin/tc filter add dev eth1 protocol ip parent 1:0 prio 3 handle 28 fw flowid 1:28
#
/sbin/tc class add dev eth1 parent 1:28 classid 1:34 htb rate 64kbit /sbin/iptables -A POSTROUTING -o eth1 -t mangle -d 192.168.200.8/32 -j MARK --set-mark 34
/sbin/tc filter add dev eth1 protocol ip parent 1:0 prio 3 handle 34 fw flowid 1:34
#
/sbin/tc class add dev eth1 parent 1:28 classid 1:35 htb rate 64kbit /sbin/iptables -A POSTROUTING -o eth1 -t mangle -d 192.168.200.14/32 -j MARK --set-mark 35
/sbin/tc filter add dev eth1 protocol ip parent 1:0 prio 3 handle 35 fw flowid 1:35
#############################################################################

iptables says:
iptables -L -n -v -t mangle
Chain PREROUTING (policy ACCEPT 184K packets, 105M bytes)
pkts bytes target prot opt
in out source destination

Chain INPUT (policy ACCEPT 115K packets, 63M bytes)
pkts bytes target prot opt
in out source destination

Chain FORWARD (policy ACCEPT 68617 packets, 42M bytes)
pkts bytes target prot opt
in out source destination

Chain OUTPUT (policy ACCEPT 123K packets, 63M bytes)
pkts bytes target prot opt
in out source destination

Chain POSTROUTING (policy ACCEPT 191K packets, 105M bytes)
pkts bytes target prot opt
in out source destination
1827 1990K
MARK all -- * eth1 0.0.0.0/0 192.168.0.0/16
MARK set 0x4
1827 1990K
MARK all -- * eth1 0.0.0.0/0 192.168.200.0/24
MARK set 0x1c
174 245K
MARK all -- * eth1 0.0.0.0/0 192.168.200.8
MARK set 0x22

    30 10519 

MARK all -- * eth1 0.0.0.0/0 192.168.200.14
MARK set 0x23

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 6 lines · Felipe Ceglia

Hi folks,

I have a strange situation. When I add branches to the tree, everything goes to the default class.
The error might be obvious, but I cannot find it. I would really appreciate your help.

<snip>

Quoted 1 line

MARK set 0x1c

This is in hex. Put 0x before the mark in the iptables and the match in the tc command to make sure they are all in hex.

Stef
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Felipe Ceglia

Hi.

Quoted 6 lines · Felipe Ceglia

Hi folks,

I have a strange situation. When I add branches to the tree, everything goes to the default class.
The error might be obvious, but I cannot find it. I would really appreciate your help.

I think it's the expected behaviour.

Quoted 2 lines

this works, nothing goes to "1:9999":

perhaps all the traffic you generate to test was marked by the iptables rules and then classified by that.
btw in this order the rule for 192.168.200.0/24 never matches, because the rule for 192.168.0.0/16 matches always first.

Quoted 5 lines

#############################################################################

/sbin/iptables -F -t mangle
/sbin/tc qdisc del dev eth1 root > /dev/null 2>&1 /sbin/tc qdisc add dev eth1 root handle 1: htb default 9999

That's whats the default parameter is for ^^^^
Traffic not classified goes to the default.

Quoted 15 lines

/sbin/tc class add dev eth1 parent 1: classid 1:1 htb rate 100Mbit ceil 100Mbit /sbin/tc class add dev eth1 parent 1:1 classid 1:9999 htb rate 128kbit /sbin/tc class add dev eth1 parent 1:1 classid 1:4 htb rate 100Mbit /sbin/tc class add dev eth1 parent 1:4 classid 1:28 htb rate 510kbit
#
/sbin/iptables -A POSTROUTING -o eth1 -t mangle -d 192.168.0.0/16 -j MARK --set-mark 4 /sbin/tc filter add dev eth1 protocol ip parent 1:0 prio 3 handle 4 fw flowid 1:4 #
/sbin/iptables -A POSTROUTING -o eth1 -t mangle -d 192.168.200.0/24 -j MARK --set-mark 28 /sbin/tc filter add dev eth1 protocol ip parent 1:0 prio 3 handle 28 fw flowid 1:28
#############################################################################

Quoted 5 lines

when I add subclasses to "1:28", traffic goes to "1:34" and "1:35", but exceeding traffic goes to "1:9999" instead of being placed at "1:28":
#############################################################################

/sbin/tc qdisc add dev eth1 root handle 1: htb default 9999

That's whats the default parameter is for ^^^^

Regards,
Francisco.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/