net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs
Subsystems (3)
PATCH v3 1/2 net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs in the micrel PHY driver, it is used even with the KSZ87xx switch. This is wrong, since the KSZ8051 configures registers of the PHY which are not present on the simplified KSZ87xx switch PHYs and misconfigures other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the KSZ87xx switch by checking the Basic Status register Bit 0, which is read-only and indicates presence of the Extended Capability Registers. The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct PHY driver instance.
---
NOTE: It was also suggested to populate phydev->dev_flags to discern
the PHY from the switch, this does not work for setups where the switch is used as a PHY without a DSA driver. Checking the BMSR Bit 0 for Extended Capability Register works for both DSA and non-DSA usecase.
V2: Move phy_id check into ksz8051_match_phy_device() and
ksz8795_match_phy_device() and drop phy_id{,_mask} from the ksphy_driver[] list to avoid matching on other PHY IDs.
V3: Pull the logic behind discerning the KSZ8051 PHY and KSZ87xx switch
into common ksz8051_ksz8795_match_phy_device() function. Add Fixes tag.
--- drivers/net/phy/micrel.c | 40 ++++++++++++++++++++++++++++++++++++---- 1 file changed, 36 insertions(+), 4 deletions(-)
drivers/net/phy/micrel.c +36 -4
@@ -341,6 +341,35 @@ static int ksz8041_config_aneg(struct phy_device *phydev)return genphy_config_aneg (phydev); } +static int ksz8051_ksz8795_match_phy_device (struct phy_device *phydev, +const u32 ksz_phy_id) +{ +int ret; + +if ((phydev->phy_id &MICREL_PHY_ID_MASK ) != ksz_phy_id) +return 0 ; + + ret =phy_read (phydev,MII_BMSR ); +if (ret <0 ) +return ret; + +/* KSZ8051 PHY and KSZ8794/KSZ8795/KSZ8765 switch share the same +* exact PHY ID. However, they can be told apart by the extended +* capability registers presence. The KSZ8051 PHY has them while +* the switch does not. +*/ + ret &=BMSR_ERCAP ; +if (ksz_phy_id ==PHY_ID_KSZ8051 ) +return ret; +else +return !ret; +} + +static int ksz8051_match_phy_device (struct phy_device *phydev) +{ +return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ8051 ); +} +static int ksz8081_config_init (struct phy_device *phydev) {/* KSZPHY_OMSO_FACTORY_TEST is set at de-assertion of the reset line
@@ -364,6 +393,11 @@ static int ksz8061_config_init(struct phy_device *phydev)return kszphy_config_init (phydev); } +static int ksz8795_match_phy_device (struct phy_device *phydev) +{ +return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ8795 ); +} + static int ksz9021_load_values_from_of(struct phy_device *phydev, const struct device_node *of_node, u16 reg,
@@ -1017,8 +1051,6 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .phy_id = PHY_ID_KSZ8051, - .phy_id_mask = MICREL_PHY_ID_MASK, .name = "Micrel KSZ8051", /* PHY_BASIC_FEATURES */ .driver_data = &ksz8051_type,
@@ -1029,6 +1061,7 @@ static struct phy_driver ksphy_driver[] = { .get_sset_count = kszphy_get_sset_count, .get_strings = kszphy_get_strings, .get_stats = kszphy_get_stats, + .match_phy_device = ksz8051_match_phy_device, .suspend = genphy_suspend, .resume = genphy_resume, }, {
@@ -1141,13 +1174,12 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .phy_id = PHY_ID_KSZ8795, - .phy_id_mask = MICREL_PHY_ID_MASK, .name = "Micrel KSZ8795",/* PHY_BASIC_FEATURES */ .config_init = kszphy_config_init, .config_aneg = ksz8873mll_config_aneg, .read_status = ksz8873mll_read_status, + .match_phy_device = ksz8795_match_phy_device, .suspend = genphy_suspend, .resume = genphy_resume, }, {
Signature · 1 line
2.23.0
PATCH v3 2/2 net: phy: micrel: Update KSZ87xx PHY name
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches. Update the PHY ID and name to reflect that, as this family of switches is commonly refered to as KSZ87xx
---
V2: Rebase on top of 1/2, no functional change
V3: Rebase on top of 1/2, no functional change
--- drivers/net/phy/micrel.c | 4 ++-- include/linux/micrel_phy.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)
drivers/net/phy/micrel.c +2 -2
@@ -395,7 +395,7 @@ static int ksz8061_config_init(struct phy_device *phydev)static int ksz8795_match_phy_device (struct phy_device *phydev) { -return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ8795 ); +return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ87XX ); } static int ksz9021_load_values_from_of(struct phy_device *phydev,
@@ -1174,7 +1174,7 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .name = "Micrel KSZ8795", + .name = "Micrel KSZ87XX Switch", /* PHY_BASIC_FEATURES */ .config_init = kszphy_config_init, .config_aneg = ksz8873mll_config_aneg,
include/linux/micrel_phy.h +1 -1
@@ -31,7 +31,7 @@#define PHY_ID_KSZ886X 0x00221430#define PHY_ID_KSZ8863 0x00221435 -#define PHY_ID_KSZ8795 0x00221550 +#define PHY_ID_KSZ87XX 0x00221550#define PHY_ID_KSZ9477 0x00221631
Signature · 1 line
2.23.0
Heiner Kallweit
maintainerQuoted 16 lines · Marek Vasut
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs in the micrel PHY driver, it is used even with the KSZ87xx switch. This is wrong, since the KSZ8051 configures registers of the PHY which are not present on the simplified KSZ87xx switch PHYs and misconfigures other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the KSZ87xx switch by checking the Basic Status register Bit 0, which is read-only and indicates presence of the Extended Capability Registers. The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct PHY driver instance.
Quoted 10 lines
Signed-off-by Marek Vasut <[email protected]>Cc Andrew Lunn <[email protected]>Cc David S. Miller <[email protected]>Cc Florian Fainelli <[email protected]>Cc George McCollister <[email protected]>Cc Heiner Kallweit <[email protected]>Cc Sean Nyekjaer <[email protected]>Cc Tristram Ha <[email protected]>Cc Woojung Huh <[email protected]>Fixes 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
The Fixes tag has to be the first one. And patch still misses the "net" annotation. For an example just see other fix submissions on the mailing list.
Quoted 101 lines
---
NOTE: It was also suggested to populatephydev->dev_flagsto discern
the PHY from the switch, this does not work for setups where the switch is used as a PHY without a DSA driver. Checking the BMSR Bit 0 for Extended Capability Register works for both DSA and non-DSA usecase.
V2: Movephy_idcheck intoksz8051_match_phy_device()and
ksz8795_match_phy_device()and drop phy_id{,_mask} from the ksphy_driver[] list to avoid matching on other PHY IDs.
V3: Pull the logic behind discerning the KSZ8051 PHY and KSZ87xx switch
into commonksz8051_ksz8795_match_phy_device()function. Add Fixes tag.--- drivers/net/phy/micrel.c | 40 ++++++++++++++++++++++++++++++++++++---- 1 file changed, 36 insertions(+), 4 deletions(-)drivers/net/phy/micrel.c +36
-4@@ -341,6 +341,35 @@ static int ksz8041_config_aneg(struct phy_device *phydev)return genphy_config_aneg (phydev); } +static int ksz8051_ksz8795_match_phy_device (struct phy_device *phydev, +const u32 ksz_phy_id) +{ +int ret; + +if ((phydev->phy_id &MICREL_PHY_ID_MASK ) != ksz_phy_id) +return 0 ; + + ret =phy_read (phydev,MII_BMSR ); +if (ret <0 ) +return ret; + +/* KSZ8051 PHY and KSZ8794/KSZ8795/KSZ8765 switch share the same +* exact PHY ID. However, they can be told apart by the extended +* capability registers presence. The KSZ8051 PHY has them while +* the switch does not. +*/ + ret &=BMSR_ERCAP ; +if (ksz_phy_id ==PHY_ID_KSZ8051 ) +return ret; +else +return !ret; +} + +static int ksz8051_match_phy_device (struct phy_device *phydev) +{ +return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ8051 ); +} +static int ksz8081_config_init (struct phy_device *phydev) {/* KSZPHY_OMSO_FACTORY_TEST is set at de-assertion of the reset line @@ -364,6 +393,11 @@ static int ksz8061_config_init(struct phy_device *phydev)return kszphy_config_init (phydev); } +static int ksz8795_match_phy_device (struct phy_device *phydev) +{ +return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ8795 ); +} + static int ksz9021_load_values_from_of(struct phy_device *phydev, const struct device_node *of_node, u16 reg,@@ -1017,8 +1051,6 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .phy_id = PHY_ID_KSZ8051, - .phy_id_mask = MICREL_PHY_ID_MASK, .name = "Micrel KSZ8051", /* PHY_BASIC_FEATURES */ .driver_data = &ksz8051_type,@@ -1029,6 +1061,7 @@ static struct phy_driver ksphy_driver[] = { .get_sset_count = kszphy_get_sset_count, .get_strings = kszphy_get_strings, .get_stats = kszphy_get_stats, + .match_phy_device = ksz8051_match_phy_device, .suspend = genphy_suspend, .resume = genphy_resume, }, {@@ -1141,13 +1174,12 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .phy_id = PHY_ID_KSZ8795, - .phy_id_mask = MICREL_PHY_ID_MASK, .name = "Micrel KSZ8795",/* PHY_BASIC_FEATURES */ .config_init = kszphy_config_init, .config_aneg = ksz8873mll_config_aneg, .read_status = ksz8873mll_read_status, + .match_phy_device = ksz8795_match_phy_device, .suspend = genphy_suspend, .resume = genphy_resume, }, {
Quoted 28 lines · Heiner Kallweit
Quoted 16 lines · Marek Vasut
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs in the micrel PHY driver, it is used even with the KSZ87xx switch. This is wrong, since the KSZ8051 configures registers of the PHY which are not present on the simplified KSZ87xx switch PHYs and misconfigures other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the KSZ87xx switch by checking the Basic Status register Bit 0, which is read-only and indicates presence of the Extended Capability Registers. The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct PHY driver instance.
Quoted 10 lines
Signed-off-by Marek Vasut <[email protected]>Cc Andrew Lunn <[email protected]>Cc David S. Miller <[email protected]>Cc Florian Fainelli <[email protected]>Cc George McCollister <[email protected]>Cc Heiner Kallweit <[email protected]>Cc Sean Nyekjaer <[email protected]>Cc Tristram Ha <[email protected]>Cc Woojung Huh <[email protected]>Fixes 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Quoted 3 lines
The Fixes tag has to be the first one. And patch still misses the "net" annotation. For an example just see other fix submissions on the mailing list.
The "net" annotation ? The net: tag is right there in the subject.
Quoted 29 lines · Marek Vasut
Quoted 28 lines · Heiner Kallweit
Quoted 26 lines · Marek Vasut
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs in the micrel PHY driver, it is used even with the KSZ87xx switch. This is wrong, since the KSZ8051 configures registers of the PHY which are not present on the simplified KSZ87xx switch PHYs and misconfigures other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the KSZ87xx switch by checking the Basic Status register Bit 0, which is read-only and indicates presence of the Extended Capability Registers. The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct PHY driver instance.
Signed-off-by Marek Vasut <[email protected]>Cc Andrew Lunn <[email protected]>Cc David S. Miller <[email protected]>Cc Florian Fainelli <[email protected]>Cc George McCollister <[email protected]>Cc Heiner Kallweit <[email protected]>Cc Sean Nyekjaer <[email protected]>Cc Tristram Ha <[email protected]>Cc Woojung Huh <[email protected]>Fixes 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Quoted 6 lines
Quoted 3 lines
The Fixes tag has to be the first one. And patch still misses the "net" annotation. For an example just see other fix submissions on the mailing list.
The "net" annotation ? The net: tag is right there in the subject.
It is missing from within the [PATCH] part of the subject, so it should be [PATCH net] for the net tree (bugfixes) or [PATCH net-next] for features (broadly speaking). This is explained in the netdev-FAQ that Heiner pointed out previously:
Signature · 1 line
Florian
David Miller
maintainerFrom: Marek Vasut <[email protected]>
Date: Sun, 13 Oct 2019 22:29:31 +0200
Quoted 29 lines · Heiner Kallweit
Quoted 28 lines · Marek Vasut
Quoted 26 lines
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs in the micrel PHY driver, it is used even with the KSZ87xx switch. This is wrong, since the KSZ8051 configures registers of the PHY which are not present on the simplified KSZ87xx switch PHYs and misconfigures other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the KSZ87xx switch by checking the Basic Status register Bit 0, which is read-only and indicates presence of the Extended Capability Registers. The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct PHY driver instance.
Signed-off-by Marek Vasut <[email protected]>Cc Andrew Lunn <[email protected]>Cc David S. Miller <[email protected]>Cc Florian Fainelli <[email protected]>Cc George McCollister <[email protected]>Cc Heiner Kallweit <[email protected]>Cc Sean Nyekjaer <[email protected]>Cc Tristram Ha <[email protected]>Cc Woojung Huh <[email protected]>Fixes 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Quoted 5 lines
Quoted 3 lines
The Fixes tag has to be the first one. And patch still misses the "net" annotation. For an example just see other fix submissions on the mailing list.
The "net" annotation ? The net: tag is right there in the subject.
It also belongs in the [ PATCH ...] area as an indicator of the target GIT tree.