Skip to contentSkip to conversation

Query regarding sampling rates etc

DISCUSSION Pharaoh . 3 participants 4 messages Jul 10, 2007 – Jul 11, 2007

lore
Share & tools
lore

Pharaoh .

author
#0 lore raw

Hi,
This is a very vague question, just thought of asking it after hours of debugging.

I am testing my alsa driver, written for omap 730/850 based board. I am testing it by using aplay.

Despite checking clocks, sampling rates etc many times and after doing many combinations thereof, I cant hear anything more than a noise which changes and becomes more like the original .wav file as I change various params like sampling rates/clocks etc. It becomes close to the actual thing, but not better.

Any idea what are the params I should be tweaking? I know this is h/w dependent.

-pharaoh

#1 lore raw
Quoted 7 lines · Pharaoh .

Hi,
This is a very vague question, just thought of asking it after hours of debugging.

I am testing my alsa driver, written for omap 730/850 based board. I am testing it by using aplay.

Quoted 9 lines

Despite checking clocks, sampling rates etc many times and after doing many combinations thereof, I cant hear anything more than a noise which changes and becomes more like the original .wav file as I change various params like sampling rates/clocks etc. It becomes close to the actual thing, but not better.

Any idea what are the params I should be tweaking? I know this is h/w dependent.

Sounds like (no pun intended) your digital audio interface is not set up correctly between your codec and CPU. It's probably best to make sure they are both using the same I2S or PCM modes.

Liam

#2 lore raw

Exactly, this sounds like when I was sending left-aligned serial audio instead of I2S format from ice1724 to the codec. Low volumes were OK, higner distorted.

Pavel.

Quoted 36 lines

------------ Původní zpráva ------------
Od: Liam Girdwood <[email protected]> Předmět: Re: [alsa-devel] Query regarding sampling rates etc
Datum: 10.7.2007 23:18:21
----------------------------------------

Quoted 7 lines · Pharaoh .

Hi,
This is a very vague question, just thought of asking it after hours of debugging.

I am testing my alsa driver, written for omap 730/850 based board. I am testing it by using aplay.

Quoted 9 lines

Despite checking clocks, sampling rates etc many times and after doing many combinations thereof, I cant hear anything more than a noise which changes and becomes more like the original .wav file as I change various params like sampling rates/clocks etc. It becomes close to the actual thing, but not better.

Any idea what are the params I should be tweaking? I know this is h/w dependent.

Sounds like (no pun intended) your digital audio interface is not set up correctly between your codec and CPU. It's probably best to make sure they are both using the same I2S or PCM modes.

Liam

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

author
#3 lore raw
Quoted 30 lines · On 7/11/07, [email protected] <[email protected]> wrote:

Exactly, this sounds like when I was sending left-aligned serial audio instead of I2S format from ice1724 to the codec. Low volumes were OK, higner distorted.

Pavel.

Quoted 8 lines

------------ Původní zpráva ------------
Od: Liam Girdwood <[email protected]> Předmět: Re: [alsa-devel] Query regarding sampling rates etc
Datum: 10.7.2007 23:18:21
----------------------------------------

Quoted 2 lines · Pharaoh .

Hi,
This is a very vague question, just thought of asking it after hours

of

Quoted 3 lines
Quoted 3 lines

debugging.

I am testing my alsa driver, written for omap 730/850 based board. I

am

Quoted 3 lines
Quoted 3 lines

testing it by using aplay.

Despite checking clocks, sampling rates etc many times and after

doing many

Quoted 1 line
Quoted 1 line

combinations thereof, I cant hear anything more than a noise which

changes

Quoted 1 line
Quoted 1 line

and becomes more like the original .wav file as I change various

params like

Quoted 1 line
Quoted 1 line

sampling rates/clocks etc. It becomes close to the actual thing, but

not

Quoted 21 lines
Quoted 7 lines
Quoted 5 lines

better.

Any idea what are the params I should be tweaking? I know this is h/w dependent.

Sounds like (no pun intended) your digital audio interface is not set

up

Quoted 12 lines

correctly between your codec and CPU. It's probably best to make sure they are both using the same I2S or PCM modes.

Liam

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

Okay, got it. But in this case wont the data on i2s line get corrupted? I could see correct data being passed on i2s data line, I tried with some unique patterns and the 2's compliment was visible on the data line.