Skip to contentSkip to conversation

Is it possible to use 2GB or DDR on MPC834x?

U-Boot Valeriy Glushkov 2 participants 4 messages Dec 30, 2008 – Jan 5, 2009

lore
Share & tools
lore
#0 lore raw

Hi Guys!

On my mpc8347 based board I can access 1GB of DDR with mapping 4 of 256MB ranges via IBAT\DBAT registers.

But with the 2 GB of DDR it's impossible to map them with BATs (there are only 8 BATs in the e300 core and the rest 4 of them are already used).

All the mpc83xx examples in the U-boot tree seem to use <=1GB of SDRAM, so they use BATs to map them.

Any suggestions are highly appreciated.

Best regards,
Valeriy Glushkov

#1 lore raw
Quoted 5 lines · Valeriy Glushkov

Hi Guys!

On my mpc8347 based board I can access 1GB of DDR with mapping 4 of 256MB ranges via IBAT\DBAT registers.

Quoted 7 lines

But with the 2 GB of DDR it's impossible to map them with BATs (there are only 8 BATs in the e300 core and the rest 4 of them are already used).

All the mpc83xx examples in the U-boot tree seem to use <=1GB of SDRAM, so they use BATs to map them.

Any suggestions are highly appreciated.

Why do you need to access all 2GB from u-boot?

-Scott

#2 lore raw

[U-Boot] Is it possible to use 2GB of DDR on MPC834x?

Hi,

Quoted 1 line

Why do you need to access all 2GB from u-boot?

I need only to recognize the real memory size and pass the value to Linux.

If I return the real value 2GB from my initdram() U-boot does not like that and resets the board.

Our devices have to support different DDR types and sizes (512/1024/2048 MB), so U-boot is responsible for DDR init and reporting its size to Linux...

#3 lore raw

[U-Boot] Is it possible to use 2GB of DDR on MPC834x?

Hi All,

The problem has been solved with defining of the following in the board config file:
#define CONFIG_VERY_BIG_RAM
#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)1024 << 20)

After that Linux recognizes all the DDR memory, while U-boot runs well using the first 1GB of it.

Best regards,
Valeriy Glushkov

----- Original Message -----
From: "Valeriy Glushkov" <[email protected]>
To: <[email protected]>
Sent: 5 ?????? 2009 ?. 14:09
Subject: Re: [U-Boot] Is it possible to use 2GB of DDR on MPC834x?

Quoted 53 lines

Hi,

Quoted 1 line

Why do you need to access all 2GB from u-boot?

I need only to recognize the real memory size and pass the value to Linux.

If I return the real value 2GB from my initdram() U-boot does not like that
and resets the board.

Our devices have to support different DDR types and sizes (512/1024/2048 MB), so U-boot is responsible for DDR init and reporting its size to Linux...

From your answer I understand that U-boot does not support >1GB of memory for MPC83xx. Is it correct?

Best regards,
Valeriy Glushkov

----- Original Message -----
From: "Scott Wood" <[email protected]>
To: "Valeriy Glushkov" <[email protected]>
Cc: <[email protected]>
Sent: 30 ??????? 2008 ?. 18:45
Subject: Re: [U-Boot] Is it possible to use 2GB or DDR on MPC834x?

Quoted 11 lines
Quoted 10 lines · Valeriy Glushkov

Hi Guys!

On my mpc8347 based board I can access 1GB of DDR with mapping 4 of 256MB
ranges via IBAT\DBAT registers.

But with the 2 GB of DDR it's impossible to map them with BATs (there are
only 8 BATs in the e300 core and the rest 4 of them are already used).

Quoted 8 lines
Quoted 4 lines

All the mpc83xx examples in the U-boot tree seem to use <=1GB of SDRAM, so they use BATs to map them.

Any suggestions are highly appreciated.

Why do you need to access all 2GB from u-boot?

-Scott

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot